DBI SALA PYTHON SAFETY 1500096 Product manual

Installation and Use Instructions for
Python Safety Scaffold Wrench Holster
with Retractor
This manual is intended to be used as part of an employee training program.
These products are not to be used for worker fall protection.
TM
Fall Protection for ToolsTM
© Copyright 2015, DB Industries, Inc.Form: 5903847-A3 Rev: A
www.capitalsafety.com
1
2
34
EN Python Scaffold Wrench Holster with Retractor
• Beacon™HighVisibilityReectorsonfrontandback.
• Quicklyholstersscaffoldwrencheswhileworkingatheight.
• D-RingsonsidesofWrenchHolsterareload-ratedfor5lbs(2.3kg).
• BackofHolsterhaspouchforPythonSafetyRetractor.
Retractorisload-ratedfor1.5lbs(0.7kg)andextendsupto
52in.(132.1cm).RearfeedsystemkeepsRetractoroutoftheway.
• HolsterandHook2LoopBungeeTethercombination(1500097)canbeused
totieoffscaffoldwrenches.
üWhen to use a Scaffold Wrench Holster with Retractor
• Tomaintainpositivecontrolofscaffoldwrencheswhileworkingatheight.
ûWhen NOT to use a Scaffold Wrench Holster with Retractor
• DonotusetoolsthatexceedD-RingorRetractorloadlimits.
Warnings
• Allwarnings,warninglabelsandinstructionsshouldbereadand
understoodbeforeusingthisproduct.Failuretodosomayresultin
property damage, serious injury or death.
• AllproceduresshowninthisinstructionareforPythonSafetyproducts
only.
• PythonSafetyattachmentpointsrequiretheuseofanappropriate
PythonSafetyLanyard,TetherorRetractorforsafeconnectionof
thetoolorequipmenttoanotherPythonattachmentpoint,theuser
orananchorage.SeespecicPythonSafetyinstructionsforproduct
installation, connection and use procedures.
• Donotuseforworkerfallprotectionorforclimbing.
• Donotuseiffallprotectionfortoolcomponentswillinterferewiththe
safeworkingconditionoroperationoftheconnectedtoolorequipment.
• Ifatoolisdroppedoraloadisforcedontotheconnectionpoint,
inspect the tool and fall protection for tool components
connected to the tool for damage.Thisincludestheattachment
point,thelanyardandtheanchorpoint.(Anchorpointexamples:tool
holster,toolbelt,toolbag,workersafetyharnessoranchorpointsuch
asarail.)Lookfortornstitchingandfordeformitiesanddamagetoany
material.Ifdamageisfound,removetheaffecteditemsfromservice
immediately and replace them.
• Inspectbefore,during,andafterusetoensurefallprotectionfortool
componentsareingoodworkingconditionandfreefromdefects,cuts,
tears,etc.See“InspectBeforeUse”inthisinstructionmanual.Never
modifyPythonSafetyproducts.
• N
everexceedthemaximumloadratingstatedonthe PythonSafety
product label.
• Neverconnectindividualtoolsthatweighmorethan5pounds(2.26kg)
to a person.
• Neverattachtoollanyardsorattachmentpointstoataperedsurface.
• Neverwrapfallprotectionfortoolcomponentsaroundroughorsharp
edges.
• Neverattachmultiplefallprotectionfortoolcomponentstogether(daisy
chain).
• Nevermakeamodicationtoaconnectedtoolorequipmentthatwill
causeittodeviatefromthemanufacturer’sspecication.
• Alwaysuseproperpersonalprotectiveequipment(PPE).
• Useextremecautionwhileworkingaroundrotatingormoving
equipment.
• Toavoidthedangerofelectricalshock,useextremecautionwhen
workingaroundpowerequipmentandconnections.
• Readandunderstandproductinformationandwarninglabelsforall
connecting lanyards and adapters.
• Allconnectedtoolsandequipmentmustbeproperlymaintainedand
inspectedfordefectsordeteriorationbeforeeachuse.
Inspect Before Use
PythonSafetyequipmentandcomponentsmustbethoroughlyinspected
before,duringandaftereachuse.Anyfallprotectionfortoolscomponent
thathasdeformities,unusualwearordeteriorationmustbeimmediately
removedfromserviceandreplaced.Inspecttheentiresurfaceofthe
component,carefullyrotatingitwhilevisuallyinspectingfordamageorwear
thatmightaffectitsusefulnessanddependability.Inspectmaterialand
stitching,hardware,D-Ringsandfasteners.Conrmthatcarabiners,trigger
snaps, retractors and other connectors operate properly.
How to use the Scaffold Wrench Holster with Retractor:
1. Insertuser’sbeltthroughtheRetractorHolsterbeltloops.
2. ThePythonSafetySteelCableRetractorfeedsthroughtherearofthe
holster.ConnecttothescaffoldwrenchbythreadingtheQuickRing
attachedtotheyokeattheendoftheRetractorCablethroughthepre-
drilledholeintheendofthewrench.
 Theconnectedscaffoldwrenchcannotexceed
1.5lbs(0.7kg)when
using the Retractor.
How to use the Scaffold Wrench Holster with Hook2Loop Bungee
Tether (1500097):
3. Scaffoldwrenchesthatweighmorethan 1.5lbs(0.7kg)butlessthan 5
lbs(2.3kg)canbetetheredtotheScaffoldWrenchHolster1500097by
usingtheincludedHook2LoopBungeeTether.Connecttheloopendof
theTethertothescaffoldwrenchwiththeincludedQuickRing.Passthe
carabinerendoftheTetherthroughtheloopandpulltighttocinchthe
TetherontheQuickRing.ConnectthecarabinertooneoftheHolster
D-Rings.
 Ifthepre-drilledholeintheendofthewrenchislargeenough,the
Tethercanbeconnectedtothewrenchhandlewithouttheuseofthe
QuickRing.FeedtheloopendoftheTetherthroughthehole.Passthe
carabinerendoftheTetherthroughtheloopandpulltighttocinch
theTetheronthehandle.ConnectthecarabinertooneoftheHolster
D-Rings.
4.
Whenthescaffoldwrenchisnotinuse,thehookandloopstrapcanbe
closedtosecurethewrenchintheHolster.Whenthescaffoldwrenchis
inuse,thestrapcanbelockedinanopenpositionforeasyholstering
andun-holsteringofthewrench.
After Use
Afteruse,cleantheHolster,Retractorandconnectedtoolorequipmentto
removedirt,corrosivesorcontaminants.Removesurfacedirtwithawipethat
hasbeenmoistenedwithamildsolutionofwaterandsoapordetergent.Work
intoathicklatherandcleantheitem.Wipewithacleanclothandhangtodry
awayfromexcessiveheat,steam,orsunlight.
Storeinacleananddryenvironment,freefromfumesorcorrosiveelements.
Propercareofsafetyequipmenthelpstoensurethatitwilloperateeffectively
andtoextenditsservicelife.
In Case of a Dropped Tool
• Ifatoolisdroppedoraloadisforcedontotheconnectionpoint,
inspect the tool and fall protection for tool components
connected to the tool for damage.Thisincludestheattachment
point,thelanyardandtheanchorpoint.(Anchorpointexamples:tool
holster,toolbelt,toolbag,workersafetyharnessoranchorpointsuch
asarail.)Lookfortornstitchingandfordeformitiesanddamagetoany
material.Ifdamageisfound,removetheaffecteditemsfromservice
immediately and replace them.
• Incidentsshouldbereportedtoyoursafetycoordinator.
1500097
1500096
Model #
1500096 Scaffold Wrench Holster with Retractor
1500097 Scaffold Wrench Holster with Retractor
and Hook2Loop Bungee Tether

www.capitalsafety.com