De Raat Sun Safe ES 045 User manual

Possibilities for bolt-down:
These safes can be bolted-down to the
floor.
Push the start button. On the screen you will see six bars
“_ _ _ _ _ _”.
Now enter the pre-set factory code 1 2 3 4 5 6.
On the screen you will see “open”.
Turn the knob to the right and turn the handle upwards
before the word “open” disappears.
Manual Sun Safe
Modellen: ES 045, ES 065, ES 080, ES 100, ES 150, ES 200, ES
400, ES 700
Opening the safe for the first time How do I set a second code?
How do I change the code in the lock?
Current (factory) code
Enter the current (factory) code and open the door.
On the inside of the door you will find a black cover.
Open this cover.
Behind this cover is a white memory button.
Press the memory button once.
On the screen you will see “-Code-” followed by “USEr_”.
Now press 1 followed by the start button.
Now you will see six bars “- - - - - -”.
Now enter your new 6-digit code.
On the screen you will see AgAiN.
Enter your new 6-digit code again.
Now you will see IN_1B which confirms your new code
has been programmed.
How do I hide the code on the screen?
Enter the current code and open the door.
On the inside of the door you will find a black cover.
Open this cover.
Behind the cover you will see a white memory button.
Press this button for 3 seconds.
On the screen you will see the word “beep”.
Next the screen will show “On-OFF”.
Press 0 followed by start to turn on the sound.
Press 1 followed by start to turn off the sound.
Please note you have to change the pre-set factory
code after the you have opened your safe for the
first time.
Enter the current code and open the door.
On the inside of the door you will find a black cover.
Open this cover.
Behind this cover is a white memory button.
Press the memory button once.
Now press 2 followed by the start button.
Now enter your new 6-digit code.
On the screen you will see AGAIN IN.
Enter your new 6-digit code again.
Now you will see IN1 which confirms your new code has
been set.
Handle Screen Keypad
Green/red light
Start buon
Key lock
Baery cover
How do I turn the sound of the lock on or off?
Press the start button twice.
Now enter your code. The code will not be visible on the
screen.
Hook on
baery cover

• When the screen shows “Lo_bAt”
• When the door of the safe will not open and you
have entered the right code en the screen shows
“OPEn”
• When you have entered the right code and the
screen shows “good” and you hear a beep twice
• When the screen will not turn when when you press
the start button
Manual Sun Safe
Modellen: ES 045, ES 065, ES 080, ES 100, ES 150, ES 200,
ES 400, ES 700
How do I lock the keypad?
When do I have to change the batteries?
How do I unlock the keypad?
Press the start button for 3 seconds.
On the screen you will see “Act”.
The keypad is now locked.
Press the start button for 3 seconds.
On the screen you will see “deAct”.
The keypad is now unlocked.
How do I change the batteries?
Enter the current code and open the door.
Under the keypad you will find a hook on the battery cover
(see picture at the beginning of the manual).
Pull the hook towards you and remove the battery cover.
Now you will have access to four batteries which you can
replace now with new ones.
We advice to use four Alkaline batteries from the brand
Duracell.
These batteries have enough voltage for the lock.
Please do not use rechargeable batteries!
Always check if the lock works correctly before closing the
door.
Frequently asked questions
Problem Pausible cause Solution
No reaction when
I push the start
button
Empty batteries Change the batteries
Placed the
batteries in the
wrong way in the
battery holder
Place the batteries in the
right way in the battery
holder
The key pad is
locked
Push the start button for
3 seconds to unlock the
keypad again
Circuit error
Contact the store where
you have bought your
safe
The screen
shows "Err-03"
You have entered
the wrong code Enter the right code
The alarm goes
off and the safe
will not open
You have entered
the wrong code 5
times
Enter the right code and
wait for 3 minutes until
the alarm stops
The green light in
on, but the safe
will not open.
The screen
shows “OPEN”
The batteries are
almost empty Change the batteries
The key has not
been turned yet Turn the key clockwise
Mailfunction in
the lock
Contact the store where
you have bought your
safe
I can not change
my code
The time frame
to change your
code has passed
Enter your new code
within the time frame of
5 seconds
The panel does
not work
Contact the store where
you have bought your
safe
The keypad does
not work
Contact the store where
you have bought your
safe
The screen
shows "Lo_bAt"
The batteries are
almost empty Change the batteries
The screen
shows "Act"
The keypad is
locked
Press the start button for
3 seconds to unlock the
keypad
I forgot my code
Contact the store where
you have bought your
safe
I can not find the
key anymore
Contact the store where
you have bought your
safe