decon Liberty LBM7013 User manual

Assembly Instructions
LBM7013, LBM7113, LBM7213
Liberty Mounting set Etac Cross 6 / Cross 6 Long
2022-03
Revision 1

Mounting set
LBM7013, LBM7113, LBM7213
__________________________________________________________________________________
__________________________________________________________________________________
Sida 2/9
1. Safety
Symbols
Risk of serious injury or death.
An operation that, if not correctly performed, may lead to injury to the operator or others.
Risk of material damage.
An operation that, if not correctly performed, may lead to material damage.
Particularly important or explanatory information
General instructions
These instructions shall always be followed when placing the mounting set LBM7013,
LBM7113, LBM7213 Mounting set Etac Cross 6 / Cross 6 Long on a wheelchair.
To be able to connect Liberty to the wheelchair Liberty also needs to be adjusted according
to the assembly instructions that is included in the delivery of Liberty.
Warnings
Assembly work or changes made to the mounting set must be carried out by trained service
technician, reseller or another person assigned by Decon.

Mounting set
LBM7013, LBM7113, LBM7213
__________________________________________________________________________________
__________________________________________________________________________________
Sida 3/9
2. Overview
Item number
Qty.
Description
A
1
Center pipe
B
2
Outer pipe
C
2
Clamp
D
2
Holder adapter bar
E
2
QR-Pin
F
2
Adapter plate
G
4
Spacer adapter plate front
H
4
Spacer adapter plate rear
I
6
Washer adapter plate
J
6
Screw M6x55 countersunk
K
6
Spring washer M6
L
6
Dome nut M6
M
4
Screw M6x14 countersunk
A
B
C
D
E
F
G
I
H
K
L
J

Mounting set
LBM7013, LBM7113, LBM7213
__________________________________________________________________________________
__________________________________________________________________________________
Sida 4/9
3. Assembly and adjustment of adaptor
First mount the adapter plate (F), spacer
adapter plate (G & H), washer adapter
plate (I). The kit includes 2 of each type of
distance adapter plates/side, front and rear
type. This is to enable the correct
placement of the adapters (F). Use a total
of 3 pcs/side.
This is kept into place using screws (J) that
is tightened on the outside of the frame
using spring washer (K) and domed nut (L).
Tighten the domed nut (L) loosely at this
point so that the complete assembly can
be moved along the frame of the wheelchair.
Now mount the adapter bar (D) bracket in the
adapter plate (F) using the screws (M).
Assemble both sides.
WARNING!
When assembly on wheelchair one support point
must always be in front of the wheelchairs brake.
J
K
L

Mounting set
LBM7013, LBM7113, LBM7213
__________________________________________________________________________________
__________________________________________________________________________________
Sida 5/9
INFO
The position of the wheelchair´s rear wheels can
affect the position of the screws (J) and holder
adapter bar (D). The positioning of the assembly
that pictures are showing can vary depending on
the position of the rear wheels of the wheelchair.
On the Cross 6 Long version it is most likely that
all the screws (J) will be positioned in front of the
wheelchair’s brakes.
Now mount the complete adapter bar
that consists of center pipe (A), outer
pipe (B) and clamp (C). The complete
adapter bar is mounted into the
holders (D) by using the QR-pins (E).
Make sure the ends of the outer pipe
(B) are parallell otherwise it can be
hard to assemble it into the holders
(D). It shall be possible to move the
center pipe sideways and also rotate
it if correctly assembled.
Now tighten all the screws (J) that holds the adapter plate in place.
INFO
Check that the arrow on the labeling mounted on the center pipe (A) is pointing towards the
front of the wheelchair. If the center pipe (A) is mounted the wrong way around it will not be
possible to attach Liberty to the bar.
D
J
M

Mounting set
LBM7013, LBM7113, LBM7213
__________________________________________________________________________________
__________________________________________________________________________________
Sida 6/9
There are two types of assembly tools. The old version where the complete spirit level is
shown and one new version where the front part of the spirit level is hidden. When using the
old version make sure that the bubble in the spirit level sits on the lines of the back part of
the spirit level (marked on the pictures bellow with a rectangle). Since the adapter bar now
have splines inside it will not be possible to get the bubble of the spirit level exactly right.
Just choose the most correct position.
Old version New version
Adjustment of the angle can be done in two different manners. Both is descriped bellow.
Alt.1
Using the adjustment tool that is
included in the delivery of Liberty (not
this mounting set), set the angle of
the adaptorbar so that the spirit level
is in level. Inside the pipes there are
splines so when rotating you will feel
and hear a clicking. When desired
angle have been accomplished, check
that the center pipe is centered in the
wheelchair. Now tighten the screws in
the clamps (C).

Mounting set
LBM7013, LBM7113, LBM7213
__________________________________________________________________________________
__________________________________________________________________________________
Sida 7/9
WARNING!
The screws holding the clamps (C)
shall be tightened to 7-9Nm of
torque.
Alt.2
Using the adjustment tool that is included in the
delivery of Liberty (not this mounting set), set the
angle of the adaptorbar. Only mount the inner pipe on
one side and then rotate the center pipe to the correct
angle. Now mount the other inne pipe in the same
position/angle as the first one. Check that the center
pipe is centered in the wheelchair. Now tighten the
screws in the clamps (C).
WARNING!
The screws holding the clamps (C)
shall be tightened to 7-9Nm of
torque.

Mounting set
LBM7013, LBM7113, LBM7213
__________________________________________________________________________________
__________________________________________________________________________________
Sida 8/9
With a measuring tape the height between
the ground and the upper docking pin of
the adapter bar is measured. This will be
used later when assembling Liberty.
Now read the assembly instructions that
was included in the delivery of the Liberty
unit. Assemble and adjust the Liberty
according to the instruction.
Don’t forget to reassemble the brakes of the wheelchair in case these were removed when
mounting the adaptor. Also, if the seat cloth was loosened during mounting of the adaptor
don’t forget to reassemble this.

Decon Wheel AB
Södra Ekeryd 119, SE-314 93 Hyltebruk, Sweden
Tel: [phone]
Fax: [phone]
E-mail: [email protected]