DeDietrich DIEMATIC 3 User manual

Installation
instructions
M000666
300003765-02
DIEMATIC 3 - FM129
DIEMATIC 3 CH - FM133
Control panel
GT 120 - GTUC 120 - GT 220 - GTUC 220 en
M000665

2DIEMATIC 3 - GT 120 / 220 27/11/2015 - 300003765-02
Contents
1 Symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
3 Installing the outside sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
3.1 Positions to be avoided . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
3.2 Installing the outside sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
4 Fitting the flow sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
5 Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
5.1 Important recommendations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
5.2 Type of connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
5.3 General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
5.4 Terminal block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
5.5 Basic connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
5.6 Connecting circuit B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
5.7 Connecting the options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
5.8 Connection of a second domestic hot water tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
5.9 Pool connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
5.10 Connecting a pool and preparation for solar heated domestic hot water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
5.11 Connecting one or two circuits with mixer valve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
5.12 Hot water storage tank connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
5.13 Basic connections if the installation is in cascade and when connecting to a regulation DIEMATIC VM. . . . . . . . . . . . . . . . . . . . .17
6 Skeleton Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

3
27/11/2015 - 300003765-02 DIEMATIC 3 - GT 120 / 220
1. Symbols used
1 Symbols used
Caution danger
Risk of injury and damage to equipment. Attention must be
paid to the warnings on safety of persons and equipment
Specific information
Information must be kept in mind to maintain comfort
ZReference
Refer to another manual or other pages in this instruction
manual
DHW: Domestic hot water
2 General
• Control panel assembly
ZSee: Boiler installation instructions.
• Fitting the boiler sensor
ZSee: Boiler installation instructions.
• Connection of the water circuit for domestic use
ZSee: Calorifier instructions.
• Installing options
ZSee: Option instructions.
• Parameter settings and installation configuration
ZSee: Control panel technical instructions.

4DIEMATIC 3 - GT 120 / 220 27/11/2015 - 300003765-02
3 Installing the outside sensor
Choose a location:
- on one face of the area to be heated, on the north if possible
- under the influence of meteorological variations
- protected from direct sunlight
- easy to access
Z: Inhabited area controlled by the sensor
H: Inhabited height controlled by the sensor
A: recommended position on a corner
B: Possible position
3.1 Positions to be avoided
3.2 Installing the outside sensor
CB Ø 4 wood screw + Inserts (provided)
A

5
27/11/2015 - 300003765-02 DIEMATIC 3 - GT 120 / 220
4. Fitting the flow sensor
4 Fitting the flow sensor
Heating circuit with mixing valve
The flow sensor with connecting cable (length 2.5 m) and connector
plug should be fitted to the outlet circuit pipe concerned and must be
connected to the point provided in the control panel as shown
hereafter.
The flow sensor after the valve must be positioned around 0.5 m after
the 3 way valve or after the heating pump if this is fitted to the outlet.
- Cut the pipe insulation by 50 mm.
- At the point where the sensor is fitted, thoroughly clean the pipes
(there must be no trace of paint) and coat them with the ready-to-
use contact paste provided in the syringe.
- Secure the sensor with the collar provided for this purpose.
The flow sensor must not be covered by the insulation around
the pipe.

6DIEMATIC 3 - GT 120 / 220 27/11/2015 - 300003765-02
5 Electrical connections
5.1 Important recommendations
The power supply must be cut prior to any intervention on
the heating installation (for example, via the appropriate
fuse or a general switch)and any restart must be
prevented.
Connections must be made by a qualified technician
Do not modify the connections inside the control panel.
All connections are made to the terminals on the control
panel.
Separate the sensor cables from the 230 V cables.
In the boiler: Use the boiler's 2 grommets:
Use 2 cableways at least 10 cm apart.
Attach the cables to the cable clamps provided for this
purpose.
GT 120
GT 220
5.2 Type of connection
For the 230 V electrical connections, use 3-wire cables with a cross-
section of 1,5 mm². Keep to the polarity shown on the terminals: phase (L), neutral (N) and earth (4).
5.3 General
Make the electrical connections of the appliance according to:
- The instructions of the prevailing standards,
- The instructions on the circuit diagrams provided with the
appliance,
- The manufacturer's instructions.
Power the appliance via a circuit which includes a remote omnipolar
switch with a gap of more than 3 mm.
Earthing shall comply with standard NFC 15100 (France) or RGBT
(Belgium).
The available output per outlet is 450 W (2 A, with cos ϕ=
0,7) and the inrush current must be lower than 16 A.
If the charge exceeds one of these values, relay the
command using a contactor (fitted outside the control
panel).
230 V main supply
For Switzerland: Power supply cable Supplied
Sensors
Cable clamps

7
27/11/2015 - 300003765-02 DIEMATIC 3 - GT 120 / 220
5. Electrical connections
5.4 Terminal block
State on delivery
6
-B
2 x 0,75 mm 2
mini.
1(A) All countries except Switzerland:
To connect the mixing valve PCB + sensor options - See:
Instructions for option FM48, AD217
1(B) For Switzerland:
To connect the mixing valve PCB + sensor options - See:
Instructions for option FM48, AD217
2Boiler sensor
3Boiler remote control input
4Alarm output
5Connecting the TELCOM vocal telesurveillance module
See chapter: Connecting the options
6Flue gas thermostat

8DIEMATIC 3 - GT 120 / 220 27/11/2015 - 300003765-02
5.5 Basic connections
For Switzerland: circuit B
ZSee next page
8575N576
Alim
230 V - 50 H z
N L
VA + CS
NLN LN LN L
AU AX
o o ooo ooo oo oo o 2 134 ooo
EU
QIN
O
H
PELETSIALER
SIA
LERNOHPEL
ET
YALERENOH
PELE
T
ERIALOS
RALOS
RALOS
SEEMUF
H
CUA
R
SA
GEULF
ERIAILIXUA
ZTASUZ
Y
RA
IL
I
X
UA
C
TI
UC
RIC
ECN
AIB
MA
CSIE
R
K
M
UA
R
C
T
IUCR
IC
MOOR
B
TI
UC
RI
CEC
NAI
BM
A
B
SIERK
M
UAR
B
TI
UCR
IC
MOOR
C
TI
U
CRI
C
TRAPED
C
S
I
E
R
KF
UAL
RO
V
C
TI
UCR
IC
WO
LFR
ETAW
ERI
A
IL
I
X
UAEP
M
OP
G
N
A
GSUA
SF
LIH
T
U
P
TUO
Y
RA
ILI
XUA
EGR
AH
CED
E
PMOP
EPM
UPED
ALRE
HCIEPS
PM
UPD
AOL
R
UETA
RELEC
CA
E
PMU
P
SGN
UZI
E
H
P
MUP
GNI
TA
E
H
ETI
RUCE
SED
TC
AT
N
O
C
T
KAT
NOKS
TI
E
HREH
CIS
TC
AT
NOCY
T
E
FAS
E
MRA
LA
T
NAY
OV
E
T
HCUE
L
MRAL
A
ROT
ACI
DN
I
M
R
A
LA
zH05V
0
32
N
O
IT
ATNEM
IL
A
z
H0
5
V
03
2
R
HUF
UZMOR
T
S
zH05V032
YLPP
USN
IAM
A
T
IUC
R
ICE
CNA
IBM
A
A
SIER
KM
UAR
B
A
TI
UC
RIC
MOOR
E
RI
ATIN
ASE
DUA
HC
UAE
RESSAWM
RA
W
RE
TA
WT
O
HC
ITSEMOD
E
R
ÈI
D
UAHC
L
ESSEK
R
E
LI
OB
RUEI
R
E
T
X
E
N
E
SSUA
LAN
R
E
TX
E
B
T
I
U
C
RI
CT
RAPE
D
BSI
ERK
F
UAL
R
OV
B
TIUC
R
IC
W
O
LF
RETAW
oo
36 3538 37
oo
40 39
oo
S FS SOL S AUX S EXTS CHS ECS
S AMB
(C)
S DEP
(C)
S AMB
(B)
S DEP
(B)
S AMB
(A)
o o
OPTION - ZUBEHÖR
SONDE - FÜHLER - SENSOR
OPTION -
ZUBEHÖR
BUS DIEMATIC
DIEMATIC BUS
12345
VA
67
(A)
8910111213141516
AUX
46 45 44 4348 4750 4952 5154 5356 5558 57 142495061626
3 x 0,75 mm
2
mini.
2 x 0,75 mm
2
mini.
2 x 0,75 mm
2
mini.
2 x 0,75 mm
2
mini.
3 x 0,75 mm
2
mini.
3 x 1,5 mm
2
mini.
ÉSOP
MI
TNA
RUO
CA
EDON
AE
DONA
MOR
TSD
ME
R
FEDON
AT
NERR
U
C
D
ESSERP
MI
TA
-A
1
2
34
5
6
7
8
9
10
11
1230 V main supply
2Flue gas thermostat
3Burner fault alarm light
4Pump circuit A
5D.H.W. load pump
6DHW sensor
7Titanium anode
8Outside sensor
9Boiler sensor
10 Boiler with or without accumulator
11 Boiler with accumulator

9
27/11/2015 - 300003765-02 DIEMATIC 3 - GT 120 / 220
5. Electrical connections
5.6 Connecting circuit B
Originally for Switzerland, FM48 option for other countries.
(1) If using a two-way motor
Connect open to terminal 232, close to terminal 223and neutral to
terminal 24 (N).
If using a thermal motor
Connect between terminal 23 2(open) and terminal 2 (N).
(2) Safety thermostat
If using underfloor heating, it is imperative that a temperature limit of
50°C is installed and a safety thermostat set to 65°C (cf. NF P 52-
303-1) is fitted, which interrupts the operation of the circulating pump
in the circuit concerned should overheating occur.
Connect the safety thermostat wires to the 5 pin connector at the
point marked TS(B) terminals 17-18 after removing the jumper from
terminals 17-18.
If the safety thermostat is fitted with an earth wire, connect the
thermostat to the earth terminal on pump 21.
mini.
2 x
MODE
+
-
1234567
0246 8 10 12 14 16 18 20 22 24
8575N394B
1
2
3
4
5
6
1Remote control (circuit B) (package FM51 or FM52)
2Flow sensor (circuit B)
33-way valve (circuit B)
4Pump (circuit B)
5Safety thermostat
6Remove bridge

10 DIEMATIC 3 - GT 120 / 220 27/11/2015 - 300003765-02
5.7 Connecting the options
For example: Solar collector, TELCOM vocal telesurveillance module, remote controls for circuits A and B, flue gas sensor.
-A
1
2
3
4
5
6
7
8
9
10
10
11
12
13
14
15
16
17
18
1230 V main supply
2Flue gas thermostat
3Burner fault alarm light
4Pump circuit A
5DHW sensor (Package AD212)
6Titan Active System® simulation connector
(package AD212)
7Outside sensor
8Boiler sensor
9Outlet sensor
10 Interactive remote control (package FM51 or FM52)
11 Flue gas sensor
12 TELCOM voice remote monitoring module (depending on its
availability in your country)
13 Solar sensor probe
14 Boiler with or without accumulator
15 Boiler with accumulator
16 DHW sensor (Package AD160)
For connection of solar collectors: adjust the S.AUX parameter (#
FITTER PARAM.) to SOLAR.
17 D.H.W. load pump
18 Solar load pump

11
27/11/2015 - 300003765-02 DIEMATIC 3 - GT 120 / 220
5. Electrical connections
5.8 Connection of a second domestic hot water tank
This connection is possible if circuit A is not used
If connecting a second DHW tank, use circuit A:
- set the CIRC.A parameter (#. INSTAL PARAM.) to DHW.
- Fit the sensor (package AD 212) into the second DHW tank.
- Connect the sensor to the S.AUX input.
- Adjust the TEMP.DHW A set temperature using the key 2% 40-
80°C range to obtain a domestic hot water calorifier type operation.
-A
1
2
3
4
5
6
7
1230 V main supply
2Flue gas thermostat
3Burner fault alarm light
4DHW sensor (Package AD212)
5D.H.W. load pump
6Outside sensor
7Boiler sensor
8Boiler with or without accumulator
9Boiler with accumulator

12 DIEMATIC 3 - GT 120 / 220 27/11/2015 - 300003765-02
5.9 Pool connection
This connection is possible if circuit A is not used
-A
1
2
3
4
5
6
7
8
1230 V main supply
2Flue gas thermostat
3Burner fault alarm light
4Swimming pool sensor (Package AD212)
5Pool secondary pump
6Primary pump pool
7Outside sensor
8Boiler sensor

13
27/11/2015 - 300003765-02 DIEMATIC 3 - GT 120 / 220
5. Electrical connections
Controlling the pool circuit
The DIEMATIC 3 regulation can be used to control a pool circuit in
two different cases:
• Case 1
The regulation DIEMATIC 3 regulates the primary circuit (boiler /
exchanger) and the secondary circuit (exchanger / pool).
- Set the value of TPC D to the temperature which corresponds to
the needs of the exchanger.
- Set the parameter S.AUX (#FITTER PARAM.) to SWIM.P.
- Set the parameter CIRC. A: (#FITTER PARAM.) to SWIM.P.
- Connect the primary circuit pump (boiler/exchanger) to the
pump A outlet. The TPC J temperature is then maintained during
programme A comfort periods in summer and in winter.
- Connect the pool sensor (package AD212) to the S.AUX: input.
- Set the value of the pool sensor using key 2% in the range 0.5-
39°C or to FF (Frost Free).
- With an FF setting, the primary pump starts up and the secondary
pump stays off if the installation's antifreeze function is activated.
• Case 2
The pool has already a regulation system that is to be kept. The
DIEMATIC 3 control unit only regulates the primary circuit (boiler/
exchanger).
- Set the value of TPC D to the temperature which corresponds to
the needs of the exchanger.
- Set the CIRC.A parameter in #INSTAL PARAM. to POOL
- Connect the primary circuit pump (boiler/exchanger) to the
pump A outlet. The TPC J temperature is then maintained during
programme A comfort periods in summer and in winter.
Hourly programming of the secondary circuit pump
The secondary pump operates during programme A comfort periods
in summer and winter alike.
Stopping
To prepare your pool for winter, consult your pool specialist.

14 DIEMATIC 3 - GT 120 / 220 27/11/2015 - 300003765-02
5.10 Connecting a pool and preparation for solar heated domestic hot water
This connection is possible if circuit A and either circuit B or C are not used.
-A
1
2
3
4
56
7
8
10
9
111213
14

15
27/11/2015 - 300003765-02 DIEMATIC 3 - GT 120 / 220
5. Electrical connections
Parameter settings
- Fit the mixing valve PCB + sensor option (Package FM 48)
- adjust the S. AUX parameter to SWIM. P.
- adjust the CIRC.A parameter to SWIM. P.
- adjust the CIRC.B parameter to SOLAR
5.11 Connecting one or two circuits with mixer valve
ZTo connect the mixing valve PCB + sensor options - See:
Instructions for option FM48
For Switzerland:
1 PCB + sensor for a mixing valve is already prefitted to the
control panel.
1230 V main supply
2Flue gas thermostat
3Burner fault alarm light
4Primary pump pool
5Pool secondary pump
6Swimming pool sensor (Package AD212)
7DHW sensor
8DHW sensor (Package AD212)
9D.H.W. load pump
10 Solar load pump
11 Outside sensor
12 Boiler sensor
13 Titan Active System® simulation connector
(package AD 212)
14 Solar sensor probe

16 DIEMATIC 3 - GT 120 / 220 27/11/2015 - 300003765-02
5.12 Hot water storage tank connection
The storage tank handles heating and DHW production.
Package AD160 contains 2 sensors:
- The sensor for the solar panel is used as a storage tank sensor
- The sensor for the storage tank is used as a DHW sensor
Parameter settings
Set the parameter STOR.T.SENS (#CONFIGURATION) to ON.
Operation
• In DHW production:
Operation is the same as the normal operation. The boiler setting
only is equal to the DHW setting +10 K. The heating load pump
is off.
• In heating mode:
The burner and the heating load pump:
-are off if the temperature of the storage tank is higher than the
boiler setting.
-start up if the temperature of the storage tank falls below the
boiler setting -6 K.
-A
1
2
3
4
5
6
7
8
9
10
11
12
1230 V main supply
2Flue gas thermostat
3Burner fault alarm light
4Pump circuit A
5Outside sensor
6Boiler sensor
7Titan Active System® simulation connector
(package AD212)
8DHW sensor (Package AD212)
9Hot water storage tank sensor (Package AD160)
10 Buffer tank
11 D.H.W. load pump
12 Heating load pump

17
27/11/2015 - 300003765-02 DIEMATIC 3 - GT 120 / 220
5. Electrical connections
5.13 Basic connections if the installation is in cascade and when connecting to a regulation
DIEMATIC VM
(Without option AD217)
5.13.1 Master boiler 1
(1) The boiler can be connected to a boiler in cascade or to a
DIEMATIC VM using a BUS cable (package AD134 or DB119).
-A
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1230 V main supply
2Flue gas thermostat
3Burner fault alarm light
4Primary injection pump
5D.H.W. load pump
6Titan Active System® simulation connector
(package AD 212)
7DHW sensor
8D.H.W. loop back pump
9Outside sensor
10 Boiler sensor
11 Boiler with or without accumulator
12 Boiler with accumulator
13 To the Diematic VM (1) regulation
14 To 2 secondary boiler (1)

18 DIEMATIC 3 - GT 120 / 220 27/11/2015 - 300003765-02
5.13.2 Secondary boiler
-B
1
2
34
5
6
7
8
9
1230 V main supply
2Flue gas thermostat
3Burner fault alarm light
4Primary injection pump
5Boiler sensor (Follower boiler)
6Boiler with or without accumulator
7From the previous cascade boiler
8Not used
9Boiler sensor on common output

19
27/11/2015 - 300003765-02 DIEMATIC 3 - GT 120 / 220
5. Electrical connections
5.13.3 Cascade
To construct the cascade, set the parameter CASCADE
(#CONFIGURATION) on each boiler to 1 and 2 respectively.
Set the parameter CIRC. A: to PRIM.P. on boiler .
The boilers switch over every 7 days.
If necessary, the startup of the secondary boiler is timed at 4 minutes.
1Master boiler
2Secondary boiler
3Primary injection pump
4Common outlet sensor to be connected to the S ECS input on boiler

5Mixing valve and circulating pump
To connect the mixing valve PCB + sensor options, See: Instructions
for option FM48

20 DIEMATIC 3 - GT 120 / 220 27/11/2015 - 300003765-02
6. Skeleton Diagrams
6 Skeleton Diagrams
Plan n° : 300008992-001-A
N
S3 T2 T1 L1B4
Ë
ËË Ë
J1
1
J1
5
J1
2
J1
6
J1
3
J1
4
J3
1
J3
2
J3
3
J3
4
J3
5
J3
8
J3
7
J3
6
J3
9
J2
2
J2
1
J2
3
J2
4
J2
5
J3
10
CSÄ AUX
L
LL LN
NN N
VA
L
LL LN
NN N
Ä A
L
LL LN
NN N
Ä Ã
L
LL LN
NN N N
NN NL
LL L
RL PA RL ECS RL AUX
RL BR
S EXT
θ°
C
1
11 12
22 2
S CH
θ°
C
1
11 12
22 2
S ECS
θ°
C
1
11 12
22 2
S AMB A S DEP B
θ°
C
1
11 12
22 21
11 12
22 2
S AMB B
1
11 12
22 2
Ì Ì
1
11 12
22 23
33 34
44 4
Ì
S DEP C
θ°
C
1
11 12
22 2
S AMB C
1
11 12
22 2
S AUX
θ°
C
1
11 12
22 2
S SOL
θ°
C
1
11 12
22 2
S
FUMEE
θ°
C
1
11 12
22 2
0 2 4 6 8 1012141618202224
AUTO
ËÃ ÀÈÁ Ä
A B C
A B CA B C A B C
+-
T A
2a 2b
VA
3 2
1
θ
θθ θ
TS
1a1
2a
2b
2
1a1b
1
ZM
ZG
2a
2
1a
1
TEST
STB
TEST
STB
2a 2b
2
1a 1b
1
ZT ZT
å
åå å å
åå å
AUTO
AUTOAUTO AUTO AUTO
AUTOAUTO AUTO
Alim
230 V-50Hz
FA
24 V (RL)
+-+-
Schéma de principe - Stromlaufplan - Principle diagram - Principeschema "DIEMATIC III"
Schéma de principe - Stromlaufplan - Principle diagram - Principeschema "DIEMATIC III"Schéma de principe - Stromlaufplan - Principle diagram - Principeschema "DIEMATIC III" Schéma de principe - Stromlaufplan - Principle diagram - Principeschema "DIEMATIC III"
DJ 6A
TEST SCHAKELAARTEST SWITCHZT
MANUEL SCHAKELAARMANUAL MODE SWITCHZM
ALGEMENE SCHAKELAARMAIN SWITCHZG
ALARM LAMPJEALARM INDICATORVA
VEILIGHEIDSTHERMOSTAATSAFETY THERMOSTATTS
KETELTHERMOSTAATBOILER THERMOSTATTCH
CORROSIEBESCHERMINGSANODEELECTRIC ANODET A
SOLAR VOELERSSOLAR SENSORS SOL
ROOKGASSEN VOELERSSMOKE SENSORS FUMEE
BUITEN VOELERSOUTSIDE SENSORS EXT
SANITAIR WARM W ATER VOELERSDOMESTIC HOT WATER SENSORS ECS
VERTREVOELERFLOW SENSORS DEP
KETEL VOELERSBOILER SENSORS CH
VACUUM VOELERSAUXILIARY SENSORS AUX
RUIMTEVOELERROOM SENSORS AMB VERWARMINGSPOMPE RELAISHEATING PUMP CONTROL RELAYRL PA RELAIS STURING LAADPOMPLOAD PUMP CONTROL RELAYRL ECS BRANDER RELAISBURNER CONTROL RELAYRL BR AFZONDERINGSKLEP RELAISAUXILIARY PUMP CONTROL RELAYRL AUX NULLEIDERNEUTRALN FASEPHASEL AANSLUITKLEMPRINTED CIRCUIT BOARD PLUGJ. TELEFONISCH RELAISTELEPHONE RELAYÌ ONSTORINGS-FILTEREMI SUPPRESSORFA BRANDERBURNERË THERMISCHE BEVEILIGINGCIRCUIT BREAKERDJ6A VEILIGHEIDSCONTACTSAFETY CONTACTCS HULPUITGANGPOMPAUXILIARY PUMPÄ AUX LAADPOMPLOAD PUMPÄ Ã VERWARMINGSPOMP KRING AHEATING PUMP CIRCUIT AÄ A
TESTSCHALTERINTERRUPTEUR TESTZT UMSCHALTER FÜR HANDBETRIEBINTERRUPTEUR MANUELZM HAUPTSCHALTERINTERRUPTEUR GENERALZG ALARMLEUCHTEVOYANT ALARME
VA
SICHERHEITSTEMPERATURBEGRENZERTHERMOSTAT DE SECURITETS KESSEL TEMPERATURREGLERTHERMOSTAT DE CHAUDIERETCH FREMDSTROMANODEANODE A COURANT IMPOSET A SOLAR FÜHLERSONDE SOLAIRES SOL ABGASFÜHLERSONDE FUMEES FUMEE AUSSENFÜHLERSONDE EXTERIEURES EXT WARMWASSERFÜHLERSONDE EAU CHAUDE SANITAIRES ECS VORLAUFFÜHLERSONDE DE DEPARTS DEP KESSELFÜHLERSONDE CHAUDIERES CH FÜHLER ZUSATZSONDE AUXILLIAIRES AUX
RAUMFÜHLERSONDE D' AMBIANCES AMB HEIZUNGSPUMPE STEUERRELAISRELAIS DE COMMANDE ACCELERATEURRL PA SPEICHERLADEPUMPE STEUERRELAISRELAIS DE COMMANDE POMPE DE
CHARGE
RL ECS
BRENNER STEUERRELAISRELAIS DE COMMANDE BRULEURRL BR ZUSATZPUMPE STEUERRELAISRELAIS DE COMMANDE POMPE
AUXILIAIRE
RL AUX
NULLEITERNEUTREN PHASEPHASEL LEITERPLATTE STECKERCONNECTEUR CIRCUIT IMPRIMEJ. FERNSPRECHRELAISRELAIS TELEPHONIQUEÌ FUNKENENSTÖRUNGSFILTERFILTRE ANTIPARASITEFA BRENNERBRULEURË LEISTUNGSSCHALTERDISJONCTEURDJ6A SICHERHEITSKONTAKTCONTACT DE SECURITECS ZUSATZPUMPEPOMPE AUXILIAIREÄ AUX SPEICHERLADEPUMPEPOMPE DE CHARGEÄ Ã KESSELKREISPUMPE KREIS AACCELERATEUR CIRCUIT AÄ A
TCH