Dell S520 User manual

Dell Interactive Projector S520 Screen/Whiteboard
PTDRV

2
Important Safety Instructions
WARNING: Failure to read, thoroughly
understand, and follow all instructions can result
in serious personal injury, damage to equipment,
or voiding of factory warranty! It is the installer’s
responsibility to make sure all components are
properly assembled and installed using the
instructions provided.
WARNING: Failure to provide adequate
structural strength for this component can
result in serious personal injury or damage to
equipment! It is the installer’s responsibility
to make sure the structure to which this
component is attached can support ve
times the combined weight of all equipment.
Reinforce the structure as required before
installing the component. The wall to which
the screen/whiteboard is being attached may
have a maximum drywall thickness of 5/8”
(1.6cm) for wood stud installation, and 1/2”
(1.3cm) minimum for steel stud installation.
WARNING: Use this screen/whiteboard
system only for its intended use as described
in these instructions. Do not use attachments
not recommended by the manufacturer.
WARNING: Do not use this product outdoors.

3
14.02 in.
(356.2 mm)
78.75 in. (2000.1 mm)
80.37 in. (2041.4 mm)
4.99 in.
(126.7 mm)
5.02 in.
(127.4 mm)
4.99 in.
(984.8 mm)
15.23 in.
(386.8 mm)
6.6 in. (167.52 mm)
1.21 in.
(30.65 mm)
41.60 in.
(1056.5 mm)
55.52 in.
(1410.1 mm)
1.67 in. (42.3 mm) 2.4 in. (60.9 mm)
28.07 in.
(712.9 mm)
Front View
Side View
Back View
Top View
Product Dimensions

4
1/8 in. (wood)
1/2 in. (drywall)
8 mm (concrete)
6 mm (concrete – AF6 toggler)
7/16” Wrench
#8 X 1/2” Screws (5)
1/4” Washer (3)
#8 x 3/4” Screws (1)
#8-10 Wall
Anchor (7)
Screen Bracket (3)
#8 x 1” Screws (7)
1/4” x 1-1/2”
Lag Screw (3)
Screen (1) Wall Bracket (1)
Cable Cover
Clips (2)
Cleaning Cloth (1)
Cable Cover (1)
Marker Tray (1)
Sensor Cover (1)
#2 Phillips Screwdriver
Carpenter’s Level Ruler
Tools Required for Installation
Parts
Included InstallationHardware

5
1. Determine desired height of image (measured
from oor) (Figure 1).
2. Determine desired center of image area (Figure 1).
3. Measure 4-1/16” up from desired height (top) of
image and 4” to the right of center of screen and
mark location (Figure 1).
4. Determine location of studs behind drywall.
5. Drill one pilot hole into a wall stud at location
marked in Step 3 (Figure 1).
Studs
Center of
Screen
Floor
73-3/4 in.
46-1/8 in.
4-1/16 in.
Figure 1
4 in.
Height
from Floor
Installation

6
6. Install (1) 1/4” x 1-1/2” bolt and (1) washer through
middle of bracket into previously drilled hole,
leaving 1/2” of the bolt extending from wall. Use
carpenter’s level to make sure bracket is properly
level (Figure 2).
7. Position level on top of wall bracket. Move bracket
until level. Drill (2) holes for the other bolts in wall
studs.
8. Install the other (2) 1/4” x 1-1/2” bolts and (2) 1/4”
washers in the previously drilled holes. Tighten all
bolts against wall bracket.
9. Measure down 52-1/4” on center and mark spot.
Move right and left of screen until wall studs are
found and mark (Figure 3).
10. Install the (3) screen brackets using:
Wood or steel studs: (3) supplied #8 x 1” screws.
Concrete wall or no studs: (3) supplied #8-10 wall
anchors and (3) supplied #8 x 1” screws.
11. Install projector mount. Refer to the S520 Dual
Stud Wall Mount (MSP-DCCUST2) manual. Do not
install the (2) plastic covers for mount (Figure 4).
12. Run cables for projector up through hole in wall
bracket and cover to projector location (Figure 5).
Middle Fastener
Previously
Drilled Hole
Center of Screen
IR Sensor Power
Projector Signal Cable
Projector Power Cord
Figure 2
Figure 3
Figure 4 Figure 5
52-1/4 in.
Installation (continued)

7
13. Mount screen onto wall bracket by hooking into
the back groove of the screen frame (Figure 6).
14. Secure bottom of screen to wall using (3) of
the supplied #8 x 1/2” screws through bottom
brackets into the lower channel of the screen
frame (Figure 7).
15. Secure marker tray to right side of screen frame
at desired height by using (2) of the supplied
#8 x 1/2” screws into the side channel of the
screen frame (Figure 8).
16. Secure IR sensor bar (packaged with the S520
Projector) to screen by sliding it onto the metal
bracket. Insert safety screw through IR sensor
bar into bracket (Figure 9).
Figure 6
Figure 8
Figure 7
Figure 9
Attach marker
tray to frame with
(2) screws into the
side channel.
Installation (continued)
Safety
Screw

8
17. Attach sensor cover by snapping clips over
screen frame. Secure to frame by screwing down
into the upper channel of the screen frame with
supplied #8 x 3/4” screw (Figure 10).
18. In between the projector mount and the IR sensor
cover, cable clips will be mounted to the wall for
cable management. Attach clips to the wall using:
Wood studs: (4) supplied #8 x 1” screws.
Concrete wall or no studs: (4) supplied #8-10
wall anchors and (4) supplied #8 x 1” screws.
When secure, route cables and cords behind the
two cable cover clips. Attach cable cover to the
cable clips (Figure 11).
19. Install projector mount covers and projector.
Refer to the S520 Dual Stud Wall Mount
(MSP-DCCUST1) manual.
Figure 12
Figure 10
Figure 11
Installation (continued)

Recommended Screen/Whiteboard
Markers
This Dell S520 Screen/Whiteboard is a dual-purpose
projection screen and whiteboard. The surface of
the screen/whiteboard can be used with dry erase
markers from a wide variety of manufacturers and
brands. Do not use permanent markers with this
product.
Recommended Screen/Whiteboard
Cleaning
The supplied cleaning cloth can be used to clean
marks on the Dell S520 Screen/Whiteboard surface
made by everyday dry erase marker usage. To clean
persistent marks from dry erase markers, only use
a standard dry erase marker cleaning solution and
the cleaning cloth. To clean permanent marks and
other unintentional marks on the surface, use a non-
abrasive or non-scouring spray cleaning solution with
the cleaning cloth or a melamine foam cleaning pad.