DeLonghi CPC206AU Specification sheet

OPERATING AND INSTALLATION MANUAL
SINGLE SPLIT AIR-CONDITIONER
AND HEAT PUMP
Please carefully read this
manual before operating the
appliance.
R410a
eco

INDEX
SINGLE SPLIT 1English 11/2002
Safety standards 2
Identification of the parts 4
Remote control 6
Operating modes 8
AUTO mode 9
TIMER mode 9
DRY mode 10
SLEEP mode 10
Maintenance 11
Troubleshooting 12
Installation instructions 13
Installation of the indoor unit 15
Installation of the outdoor unit 19
Venting the air 19
Note 20
Useful information 20
U AI
U AI
U A
I
U AI
U A
I
U AI
U A
I
U AI
U AI
U A
I
AI
A
I
AI
A
I
U AI
U A
I
UUser IInstaller AService

SINGLE SPLIT
2English 11/2002
Use the power supply voltage shown on the rating
plate. Keep the power switch or plug clean.Connect
the power cable correctly and securely to the out-
let, avoiding the risk of electric shock or fire due to
insufficient contact.
Check that the outlet is suitable for the plug, oth-
erwise have the outlet replaced. Do not use the
power switch or pull out the plug to switch the
appliance off when operating.This may cause fires
due to sparks,etc.
The user must contact qualified personnel to
earth the appliance, in compliance with the legis-
lation in force, and to install a thermal-magnetic
circuit breaker.
Do not bend, pull or press the power cable, as it
may break.Electric shock or fire are usually caused
by damaged power cables.
The power cable must only be replaced by special-
ist technicians.
Do not use power supply cables that are too
long,or multiple adapters. Do not operate the air-conditioner with wet hands;this may cause electric shock.
Do not modify or alter the characteristics of the
appliance in any way.
Contact the Service Centres authorised by the
Manufacturer for all repairs.Incorrect repair may
cause electric shock,etc.
Make sure the appliance is disconnected from
the power supply when not used for extend-
ed periods, and before performing any clean-
ing or maintenance operations.
Do not install the appliance in environments
where the air may contain gases, oil or sulphur,
or near sources of heat.
Check that the base of the outdoor unit is
installed securely.
This appliance must only be used by adults; do
not allow children to play with the appliance.
Do not climb onto or rest objects on the out-
door unit.
Never insert sticks or tools into the appliance.
This may cause injuries.
Do not block the air inlet or outlet of either the
indoor or outdoor unit. Extended exposure to cold air is a health risk.
If smoke or a smell of burning is detected,imme-
diately disconnect power and contact the Service
Centre.
SAFETY STANDARDSANDWARNINGS U I A

SINGLE SPLIT 3English 11/2002
Keep the appliance at least 50cm from flamma-
ble substances (alcohol, etc.) or from pres-
surised containers (e.g.spray cans).
Selecting the most suitable temperature will avoid
damaging the appliance.
The direction of air flow must be adjusted correct-
ly.The louvers must be adjusted downwards in
heating mode,and upwards in cooling mode.
Do not leave doors and windows open when the
air-conditioner is operating for long periods.
Do not aim the air stream directly at plants or
animals. Do not spray water onto the air-conditioner.
This appliance has been designed to air-condition
the home and must not be used for other pur-
poses,such as drying clothes,cooling food,etc.
If the appliance is used in areas without the
renewal of fresh air, precautions must be taken
to prevent any leaks of refrigerant gas from
stagnating in the environment and creating the
risk of fire. Do not rest heavy or hot objects on the appliance.
The packing materials are recyclable. It is therefore
recommended to place them in suitable containers
for separate waste disposal.
At the end of its working life, take the air-condi-
tioner to a special waste disposal centre.
Only use the air-conditioner as shown in this
booklet.These instructions are not intended to
cover every possible situation that may arise.
Common sense and prudence must be applied
in the installation,operation and conservation of
all household appliances.
Lowers
the inside
temperature
by 5°C from
the outside
temperature
※Working temperature range
Maximum cooling
Maximum heating
Minimum cooling
Minimum heating
36
Indoor side DB(℃)
30
16
16
45
Outdoor side DB(℃)
27
18
-10

SINGLE SPLIT
4English 11/2002
IDENTIFICATION OFTHE PARTS
AUTO
TEST
RUN
STOP
AUTO
STOP
1
4
511
10
7
9
6
8
12
4
4
14
13
23
Air inlet
INDOOR UNIT
OUTDOOR UNIT
The above figure represents a simplified layout of the appliance and may not correspond to the
appearance of the unit actually purchased.
U I A
Air outlet
Air inlet
Air outlet
1Front panel
2Air filter
3Electrostatic filter (optional)
4Manual switch
5Cable panel
6Activated carbon filter
7Louvers
8Signal receiver
9LED display
10 Power plug
11 Drain hose
12 Remote control
13 Handle
14 Air outlet grill
4
AUTO
STOP
RUN
TEST

SINGLE SPLIT 5English 11/2002
1
2
3
4
5
AUTO
TEST
RUN
STOP
1. Manual switch
This is used to start the appliance if the remote con-
trol is not working.*
2. Heating indicator
This comes on when the appliance is in heating mode.
3. Cooling indicator
This comes on when the appliance is in cooling
mode.
4. Operation indicator
This comes on when the appliance is operating.
5. Signal receiver
Receives the signals from the remote control.
OPERATION AND DISPLAY
The shape and the position of the switches and
indicators may change according to the model,
however their functions remain the same.
Power on when grill open.
*This operation must be carried out by spe-
cialist technicians.

REMOTE CONTROL
SINGLE SPLIT
6English 11/2002
3
4
1
5
6
7
10
2
8
9
1. Liquid crystal display
Displays all the operating modes.
2. MODE button
Used to select the operating mode.
3. FAN button
Used to set the fan speed, in sequence, to automatic,
low,medium,high.
4. SLEEP button
Used to set or cancel SLEEP mode.
5. SWING button
Used to start or stop the movement of the vertical
louvers.
6. TIMER ON button
When the appliance is off, this button is used to
switch the air-conditioner on automatically.
7-8. ROOMTEMPERATURE SETTING buttons
Used to set the room temperature.
9. TIMER OFF button
When the appliance is on, this button is used to
switch the air-conditioner off automatically.
10. button
Used to switch appliance on or off.
Meaning of the symbols shown on the liquid
crystal display:
Automatic fan speed
Low fan speed
Medium fan speed
High fan speed
Cooling indicator
Dehumidification indicator
Fan only operation indicator
Heating indicator
Automatic mode indicator
SLEEP indicator
Louver swing indicator
The display on the remote control remains on even when the unit is off.
The remote control sends signals to the appliance.
U I A

SINGLE SPLIT 7English 11/2002
HOWTO FITTHE BATTERIES
•Remove the cover of the battery compartment in the
direction of the arrow.
•Fit the new batteries, making sure the (+) and (-) signs
on the battery match correctly.
•Put the cover back on by sliding it into position.
Use 2 x R03 AAA (1.5 V) batteries. Do not
use rechargeable batteries.
Replace the used batteries with new batter-
ies of the same type when the display is no
longer visible.
The batteries last around one year.
The batteries in the remote control must be
disposed of appropriately according to the
legislation in force in the country concerned.
TIPS ON STORING AND USING THE REMOTE
CONTROL
The remote control can be stored in a special support
mounted on the wall.
The remote control holder is standard
HOWTO USETHE REMOTE CONTROL
To switch the air-conditioner on, aim the remote control
towards the signal receiver.The remote control will work
at a distance of up to 8 metres from the indoor unit.
Store the remote control at least 1m from
television sets or other electrical appliances.
Signal receiver
Remote control holder

SINGLE SPLIT
8English 11/2002
OPERATING MODES
OPERATING MODES
1. Selecting the operating mode
Each time that the MODE button is pressed the oper-
ating mode is changed,in the following sequence:
FULL AUTO COOLING DRY FAN ONLY
HEATING
2. FAN mode
Each time that the FAN button is pressed,the speed is
changed,in the following sequence:
AUTO LOW MEDIUM HIGH
3. Setting the temperature
Press once to increase the set temperature
by 1°C.
Press once to decrease the set temperature
by 1°C.
Range of temperature settings available:
HEATING 16°C ~ 30°C
COOLING 16°C ~ 30°C
DEHUMIDIFICATION 16°C ~ 30°C
FAN ONLY no setting allowed
4. Starting the appliance
Press the button .
When the unit is switched on it will start
operating in the mode selected prior to
being switched off.
5. Adjusting the air flow
Pressing the “SWING” button starts moving the air
flow louvers start automatically; pressing the
“SWING” button again stops the louvers.
Do not move the vertical air flow louvers
manually,as this may cause poor operation.If
this happens, first turn the appliance off, then
disconnect and reconnect it to the power
supply.
Adjusting the horizontal air flow (manual)
Turn the louver sliders for the horizontal adjustment of
the air outlet to change the angle of the air flow,as shown
(the unit illustrated may be different from the air-condi-
tioner you have purchased).
This operation must be carried out by specialist
technicians.
12
5
4
3
3
U I A
Sliders for adjusting the horizontal air flow louvers.

AUTOMATIC START
After having switched the appliance off, press the T-ON
button to set the time you want the air-conditioner to
switch back on; pressing the T-ON button again increases
the time by 30 minutes,until a maximum of 24 hours from
when theTIMER is set.
E.g.: If the setting is performed at 4 p.m. and the TIMER is set
to 2.5h, the appliance will start at 6.30 p.m.
When the unit is switched on it will start operating in
the mode selected prior to being switched off.
AUTOMATIC STOP
When the appliance is on,press theT-OFF button to set
the time you want the air-conditioner to switch off;
pressing theT-ON button again increases the time by 30
minutes, until a maximum of 24 hours from when the
TIMER is set.
E.g.: If the setting is performed at 8.30 p.m. and the TIMER
is set to 3.5h, the appliance will switch off at midnight.
AUTO MODE
SINGLE SPLIT 9English 11/2002
AUTO OPERATING MODES
Press the MODE button until displaying AUTO ();in
this mode,the temperature and the fan speed are set auto-
matically based on the actual room temperature.
The operating mode and the temperature setting
depend on the room temperature.
InAUTO mode,the pre-set temperature is 25°C in cooling
mode,while the fan speed may change.
2.5
U I A
TIMER MODE
U I A
23°C ~ 26°C FAN ONLY
higher than 26°C COOLING
Lower than 23°C HEATING
Room temperature Mode