DELTA DORE Radio Tybox User manual

RADIO TYBOX
Installation guide
Wireless programmable thermostat
1-zone pack or 2-zone pack
RADIO TYBOX
• Carefully read these instructions prior to
installation.
• The unit must be installed in compliance with
currently applicable standards.
• Always switch off the mains before installing or
servicing the unit.
• Do not attempt to repair the unit yourself;
an after-sales service is available.
• The receiver power supply cable must only be
replaced by the manufacturer or an approved
agent.
• Check that the fastenings are suited to the surface
that the unit will be attached to (plasterboard, brick,
etc.).
• The diagrams provided are simplified for greater
clarity.The protective units and other accessories
required by the standards are not illustrated.
Standard UTE NF C15-100 and good practice must
be complied with. Connected or nearby equipment
must not generate excessive interference (directive
2004/108/CE).
Warnings
DELTA DORE - Bonnemain
35270 COMBOURG - FRANCE
E-mail: [email protected]
Device compliant with the requirements of directives:
R&TTE 1999/5/CE
Because of changes in standards and equipment, the characteristics
given in the text and the illustrations in this document are not binding
unless confirmed by Delta Dore.
*2702000_rev1*
Presentation
The 1-zone pack features a RADIO TYBOX transmitter
associated with an RF 640 receiver (1 zone).
The 2-zone pack features two RADIO TYBOX transmitters
associated with an RF 650 receiver (2 zones).
The RF 640 and RF 640 can be connected either to a
boiler or to contact switches to control electric heating.
The elements of your system (receiver and
transmitter(s)) are already associated when delivered.
For the 2-zone pack, each transmitter is identified by a
label (EMET 1, EMET 2).
Antenna
Electric
cable
Zone
1 LED
Zone
2 LED
12
Antenna
Electric
cable
Button
LED
RF 640 RF 650
Buttons
Location
The receiver must be placed near the heating control
(burner or thermostat input for a boiler, electrical
switchboard when used with a contact switch).
To avoid interference with the radio transmission, the
antenna must be free from any metallic elements
(cables, metallic covers, etc.).
receiver Mounting
Screw-mounting
Mounted on a wall using the
screws and pegs supplied.
Mounting by double-sided adhesive tape
If you fit the receiver using adhesive
tape, you must strictly follow the instal-
lation recommendations
(see “location” section).
Ensure that the surface on which the
tape is applied is thoroughly clean
before attaching the tape.
Connecting the receiver
Inverting the relay contact position
During an On command: the relay closes.
During an Off command: the relay opens.
You can invert the operation of the relay by pressing
the relevant button on the receiver for about
10 seconds.
Connecting a
boiler without
thermostat
input
If the boiler does
not have a ther-
mostat input, you
can directly control
the circulator loca-
ted next to the boi-
ler.
Circulator
blue wire
brown wire
Mains
230V
N
L
black wire
grey wire
RF 640
Grey
5 A max.
Black
Brown
Blue
NL
If necessary, remove
the shunt (electric
wire) connecting the
two thermostat input
terminals.
If the boiler has a
clock input, do not
mistake it for the
thermostat input.
Remove
the shunt
wires to be
connected to
the receiver
do not mistake it
for the clock input
(on some boiler models)
Example of a boiler
terminal box
The contact output of the RF 640 receiver is not
powered (dry contact).
Location / Mounting
For easier use, the RADIOTYBOX can be installed:
- mounted on the wall with screws and pegs at an
approximate height of 1.5 m,
- on a support placed on an item of furniture or a
shelf.
Separate the unit
from its base by
unlocking the
casing.
Starting up
Remove the bat-
teries’ protective
tabs.
Screw-mounting
Mount the base with screws and
pegs suited to the support or on
a flush-mounted box, then close
and lock the unit.
To control electrical convectors, you MUST use a
power contact switch that is suitable for the total power
to be controlled.
contact switches (not
supplied) fitted in the
electrical switchboard
N
N
L
convector(s) convector(s)
mains
supply
230V/50Hz
Power supply
of the contact
switch coil
230V N
N
L
Zone 2Zone 1
blue wire
brown wire black wire
grey wire
Grey
3A
3A
Black
Brown
Blue
NL
RF 650
Connecting the receiver
The contact outputs of the RF 650 receiver are
powered (phase).
When you turn the unit on for the first time, you will
need to set the time.
Turn the knob to .
The days flash.
Press + or - to
change the day, then
press OK to confirm
and continue on to
the next setting.
Repeat the operations to set the hours and minutes.
To leave the “time setting” mode, turn the knob.
Time setting
Minutes
Hours
Days
(1 :Monday ...
7 : Sunday)
Fitting to the base
Position the unit on its base and lock it.
Position the thermostat
on its base.
Lock the thermostat
1 2
Basic configurations (menu 1)
Press button 1,
To change the various settings, press the + or -
buttons, then press OK to confirm the change and go
to the next setting.
Choice of
programming
Weekly (by default)
Daily
Choice of
programming
increments
1-hour increments (by default)
30-minute increments
15-minute increments
Turn the knob to to
access the configuration
menus, then press the i
button for 5 seconds.
The unit will propose 4 configurations to choose from:
Configuration
Configurations of the
consumption indication function
(Menu 3)
Basic configurations (Menu 1)
Unit version
Advanced configurations (Menu 2)
Radio association
Unit version
Configuration mode
5 sec.
Menu 3 can only be accessed when the RADIO
TYBOX is associated with a RADIO TYWATT.
With thermostatic valve electric heating or hot water
heaters, the Comfort temperature can be provided by
adjusting the thermostat of each radiator.
In this case, only Economy and Frost Protection
temperatures are set by the RADIO TYBOX.
Comfort temperature set by the
RADIO TYBOX (by default)
Temperature
control Comfort Comfort temperature set on each
radiator or convector.
In this option the screen displays ConF.
Anti-seizing off (by default)
Circulator
anti-seizing Anti-seizing enabled (circulator
operates for 1 minute every
24 hours).
Connecting a boiler with thermostat input
Connect the black and
grey wires of the
receiver to both
terminals of the boiler
thermostat input.
Command sent
ON
OFF
Contact Inverted contact
ON
ON
OFF
OFF
Boiler
thermostat input
blue wire
Mains
230V
N
L
brown wire black wire
grey wire
RF 640
Grey
5 A max.
Black
Brown
Blue
NL
Press button 2.
To change the various settings, press the + or -
buttons, then press OK to confirm the change and go
to the next setting.
Advanced configurations (menu 2)
Modification
authorization
for the user
Program and temperature settings
(from 5 to 30°C) modification authorized
Program and set-point setting
modification unauthorized
(Comfort: 16 to 22°C,
Economy: 13 to 19°C
Frost Protection: 5 to 11°C)
If there is a difference between the temperature noted (ther-
mometer) and the temperature measured and displayed by
the unit, function 2-02 modifies the way the probe takes mea-
surements so as to compensate for this difference.
E.g.
If the temperature dis-
played by the unit is 19°C
and the temperature mea-
sured is 20°C, add 1°C to
the display and confirm by
pressing OK.
Correction of the
measured
temperature.
Correction possible from -5°C to +5°C
in increments of 0.1°C.
Press the + or - buttons to make changes,
and confirm with the OK button.
Continuous set-point temperature
display (by default)..
With this option, press i to display
the room temperature.
Automatic mode
temperature
display option Continuous room temperature
display.
With this option, press i to display
the set-point temperature.
Advanced configurations (menu 2)

Radio association (menu R)
This menu lets you associate all the installation’s
wireless products (transmitters and receivers) with the
RADIO TYBOX.
Go to the radio association menu
Home automation features on the
installation
Up to 8 home automation products can be associated
with the RADIO TYBOX.
The features are the following:
- operation with door/window magnetic contacts,
- operation with a TYXAL alarm central control unit,
- operation with TYXAL or TYDOM remote controls
(Delta Dore),
- operation with a home automation transmitter (e.g.
TYDOM 310).
Press + or - to display “1” flashing.
Confirm on the RADIO TYWATT.
Check on the RADIO TYBOX that “1” is no longer
flashing.
The RADIO TYBOX and the RADIO TYWATT are asso-
ciated.
Consumption
indication function
No consumption indication
Consumption indicator to associate
Press + or - to make your choice.
Press OK to confirm and go to the next mode.
Fonctionsdomotiques
sur l'installation
Pas de fonctionsdomotiques
Fonctionsdomotiquesassociées
au RADIO TYBOX
Transmitter Association
Press the button.
Simultaneously press and hold the buttons
for 5 seconds, le LED comes on,
goes off, and then comes back on, release
the buttons.
Door/window
Open Window:
heating in frost
protection mode
TYXIA remote
control
Comfort or
Economy overrides.
Radio association
From the menu rAd.
1st step: the receiver is delivered already associated
with the transmitter.
The display indicates “rAd” as well as the number of
associated products (1 receiver).
You can go straight on to the 2nd step, associating
home automation products
To associate a wireless receiver again, you must first
remove all associations (see Removing radio
associations section), then, on the receiver: for three
seconds, press and hold the button of the channel you
wish to associate.
The corresponding LED flashes.
Press ion the RADIO
TYBOX.
The screen displays “1”.
The receiver is associated
with the RADIO TYBOX
2nd step: associating the home automation products.
On the transmitter, confirm
the association as indicated
in the table or refer to its
user guide.
Each newly associated
transmitter is displayed on
the screen.
The association operation is carried out channel by
channel on the RF 650 receiver.
Number of associated
transmitters
Transmitter Association
123
456
789
0#
Enter the first 4 numbers of the access
code (1234 by default), then press the
button for 5 seconds.
( )
Set the control unit to maintenance mode
before switching the RADIO TYBOX to radio
association (menu rAd).
Simultaneously press and hold the ON and
OFF buttons of the unit’s control device for 5
seconds to switch to maintenance mode.
Open the cover of the control unit and press
the “test” button.
Close the control unit.
Once the radio associations are made, press the OK
button to confirm and go on to the next mode.
Telephone
transmitter
Remote control of
the installation
TYXAL control unit
Monitoring
alarm on:
Heating in
Economy mode
Monitoring
alarm off:
Heating in
Comfort mode
Radio association (menu R)
Transmitter Association
Press the domain button until
until the remote control emits a beep and
the symbol flashes.
Associate the buttons and
Press one of the tactile buttons
or .
Associate the buttons and
Press one of the tactile buttons or .
To exit the association mode, press another
domain button (e.g. ).
Open the sensor’s casing.
Press the association button,
the red LED will switch on then off.
Close the sensor unit.
Home automation
remote control
Overrides
Comfort / Economy
or
On / Off
Outdoor
probe
Indication
of the outdoor
temperature
Configurations 3-13 to 3-18 let you modify costs
according to your subscription.
After menu 3 has been configured, the unit returns to the
choice of menus.
To exit the configuration, turn the knob to the right.
IMPORTANT: The consumption value that you can
read on the digital screen is a non-contractual
indication and cannot be substituted with the
consumption value mentioned on your electricity bill.
Base OP OP blue day
Base Double tariff tempo EJP
Normal
hours
-PH PH blue day
white day OP
white day PH
red day OP
red day PH
Peak
hours
-- -
-- -
-- -
-- -
Subscription
option
PH: Peak Hours
,
OP: Off-
p
eak Hours
The menus 3-12 to 3-18 are only accessible if the
RADIO TYBOX is associated with a RADIO TYWATT.
To access the display of consumption, heating, DHW
and other uses, you must declare the number of CTs
(current transformers, ref. 6330004) associated with the
RADIO TYWATT option.
3-13 to 3-18 Cost per Kwh (incl. tax)
The price displayed is the price per kWh
(excl.subscription) expressed in euros including taxes
(price including municipal and regional taxes and VAT
(average of 30%)).
For further information, contact
your electricity provider.
We advise you to round to the
nearest cent.
E.g. 0.1085 euros gives
0.11 euros.
0.11 euros (incl. tax)
Number of CTs
No consumption indication
(by default)
1 CT (Heating)
2 CTs (Heating + DHW)
Not used
Option configuration (menu 3)
Returning to the factory configuration is possible for
each of the menus.
Turn the knob to , then press and hold the ibutton
for 5 seconds.
Follow the same steps for the other menus.
To exit this mode, turn the knob to the right.
Return to the factory configuration
Press the button of the menu
you wish to reset, and hold the
button for 5 seconds
(this example uses menu 1).
Then press the OK button to
confirm the reset.
To cancel all radio associations, turn the knob to ,
then hold the ibutton down for 5 seconds.
To associate the receiver with the transmitter again,
refer to the “radio association” section.
Removing radio associations
Press and hold the R button
for 5 seconds.
Then press the OK button to
confirm the reset.
NOTE:You can manually reset the receiver by
pressing the button of the channel to associate for
30 seconds until the LED flashes rapidly.
Summary table of configurations
1-01 Type of programming
0 = weekly 1 = daily
1-02 No programming
0 = 1 hour 1 = 30 minutes 2 = 15 minutes
1-08 Controlling the Comfort temperature
0 = controlled by the RADIO TYBOX
1 = by each radiator or convector.
1-09 Circulator anti-seizing
0 = off
1 = on
2-01
Modification authorization
0 = Program and settings may be changed
1 = Program not modifiable and set-point
temperature settings limited (Comfort: 16 to 22°C,
Economy: 13 to 19°C, Frost Protection: 5 to 11°C)
2-02 Correction of the measured temperature
from -5°C to +5°C in increments of 0.1°C.
2-04 Automatic mode temperature display option
0 = Set-point temperature display
1 = Room temperature display
Turn the knob to , then hold the 2nd button
(from the top) down for 5 seconds until tESt appears.
The LED on the receiver should flash for each
reception (approximately every 6 seconds).
If this happens, radio transmission is occurring
correctly.
If this does not occur, move your transmitter.
Turn the knob or press the OK button to exit the tESt
mode.
Radio test
5 sec.
Technical characteristics
RADIO TYBOX transmitter
•Power supplied by two LR03 or AAA-type 1.5 V
alkaline batteries (supplied), autonomy of 2 years for
normal use
• Class III insulation
• Clock back-up in the event of battery change:
30 seconds
• Radio range 100 to 300 metres outside, variable
depending on the associated equipment (the range
can be altered depending on the installation
conditions and the electromagnetic environment)
• Radio frequency 868 MHz, class I
(standard EN 300 220)
• Wireless remote control device
• Dimensions: LxHxD = 80 x 103 x 16 mm
• Protection index: IP 30
• Storage temperature: -10°C to +70°C
• Operating temperature: 0°C to +40°C
• Installation in an environment with normal pollution
levels
• Mounting with screws or on a support
Radio association (menu R)
r-01 Home automation features
0 = No 1 = Yes
r-02 Consumption indication
0 = No 1 = Yes
rAd Radio association
zone
rAd 1 Reserved menu
With a RADIO TYWATT
3-12 Number of CTs
0 = No RADIO TYWATT 1 = 1 CT (Heating)
2 = 2 CTs (Heating + DHW) 3 = 3 CTs (Three-phase)
3-13
à
3-18 Cost per kWh according to subscription
Summary table of configurations Troubleshooting
Nothing is displayed on the room unit screen.
There is no power supply.
Check the batteries.
The receiver does not accept orders from the transmitter.
• Check the transmission by performing a radio test.
• Move your transmitter if necessary.
• Repeat the radio-controlled association of the receiver with
the RADIO TYBOX.
The indication is displayed.
The batteries are low.
Change the batteries, making sure they are the right way round.
The unit displays: dEF 6
There is a communication fault between the RADIOTYBOX
and the RF 640 or RF 650 receivers.
Check the installation.
You wish to associate a home automation feature and the
screen displays ---- .
You have reached the maximum number of functions to
associate.
During the radio association, then device displays:
Zone rAd 1.
This menu is reserved.
Associate the receiver again from the rAd menu.
RF 640 / RF 650 receivers
•230 V, 50 Hz power supply, ±10%
• Class II insulation
• Power consumption: 0.5VA
• 1 dry contact output, 5 A max. (RF 640)
• Two 3 A powered contact outputs,
230 V Cos ϕ= 1 (RF 650)
• Radio frequency 868 MHz (standard EN 300 220)
• Radio range 100 to 300 metres outside, variable
depending on the associated equipment (the range
can be altered depending on the installation
conditions and the electromagnetic environment)
• Type 1.C automatic action (brownout)
• Operating temperature: -5°C to +55°C
• Storage temperature: -10°C to +70°C
• Dimensions: LxHxD = 102 x 54 x 20 mm
• Protection index: IP 44
• Installation in an environment with normal pollution
levels
Technical characteristics
“Consumption
indication” feature
To associate a consump-
tion indicator with the
RADIO TYBOX (e.g.
RADIO TYWATT).