Dension GBL-9222-1 User manual

Gateway Lite BT
iPod, USB and Bluetooth
(A2DP & HFP)
Install Guide
v.1.0
GBL-9222-1
1. INTRODUCTION
Gateway Lite BT enables music playback from a
USB storage or iPod through your vehicle’s
entertainment system, using the buttons of the
car stereo for basic control.
This device also offers handsfree mobile call
handling via the original buttons of the Head Unit
(Radio).
Gateway Lite BT is designed to give easy to
manage control, in cars where it is not possible
to display text, therefore only basic control is
available (track skip functions and USB folder
browsing).
2. GETTING STARTED
At first please make sure that the vehicle
compatibility is correct.
The Dension Gateway Lite BT is available in
specific versions for different vehicle types,
therefore the exact operation and installation
may be different in each case.
Warning!
During the installation always make sure that
the ignition key is removed from the car, the
radio is switched off and that you have the
security code of the head unit (radio)
available (if applicable).
3. HOW TO REMOVE THE HEAD UNIT
First, carefully remove your vehicle's existing
factory fit head unit as per the factory instructions
and using the correct tools.
In some cases, removing the head unit will
require panel removal as well therefore we
recommend to contact your vehicle's dealer or
installation supplier / installer for more
information.
3. FITTING THE GATEWAY HARNESS
Once the head unit has been removed,
disconnect the antenna cable (1) and then unclip
the main wiring connector from the head unit (2).
This will differ in all makes and manufacturers.
With the main radio cable removed, first connect
the Dension supplied cable to the original factory
cable harness.
In some cases there may be an add-in
connector. Remove the CD changer section and
replace with the loom supplied with the Gateway
Lite Blue. For further details please go to section
6.
Please note: The free brown lead on the
Gateway car harness needs to be connected to
the phone mute pin of the radio.
Important installation notes for Volkswagen
and Audi owners:
The free black lead on the Gateway harness
must be grounded / connected to the chassis
of the radio. In case of BMW you don’t need to
connect this lead.
4. CONNECTION
The below diagram depicts how the
different modules connect to the Gateway
Lite BT.
Connect the round iPod connector and USB to
the module and feed them through the
dashboard to an appropriate location.
Warning! Do not trap the cables, or leave
them in a position where they may become
trapped after refitting the head unit.
Ensure the device is correctly fitted before
running the cable. Then, reconnect the Dension
supplied main radio connector to the rear of the
head unit.
Connect the 12 way micro-fit (12 pin molex) to
the Car side of the Gateway Lite BT module.
5. INSTALLATION
Fitting the microphone
The microphone will work best when it is kept
away from all noise sources (open windows or
speaker) and close to the speaker. So the best
place to ensure perfect sound is to install at the
central light cluster or rear view mirror in the
center of the wind screen. There are clips that
help you to do this.
The optimal place for the microphone depends
on many factors, so it is recommended that you
try different installation places before finally
mounting the microphone

6. TEST AND REFIT
Before you refit the head unit, test the Gateway
Lite BT with your car audio, making sure all
connections are correct and that you have full
functionality.
Note: If during testing you notice any
changes or inconsistencies in the way the
car's electrical system operates, disconnect
the Gateway product immediately and consult
your dealer.
When you have tested everything, refit your head
unit. Take care not to trap any wires or the
Dension product. We supply cable ties to mount
the Gateway Lite BT module. Please mount the
module away from heat or damp surfaces.
Refit of the Head Unit is the reversal of the
removal process for your specific vehicle, as per
your manufacturer's instructions.
7. CAR-SPECIFIC CONNECTIONS
Cars with mini ISO connector
BMWs with 17-pin connector
Cars with Quadlock connector (not break-in)
If the CDC connector has a separate housing
7. DISCLAIMER
All photos / illustrations are for representation
purposes only and may differ visually from the
equipment in your vehicle. Information correct at
time of going to print E. & O. E. Dension Audio
Sytems Ltd. and it’s registered partners cannot
be held liable for any damages caused by the
incorrect installation of any Dension product.
8. FURTHER ASSISTANCE
If you need further assistance in using your
Dension product, please contact your local
supplier or visit www.dension.com/en/support
and click on ‘Support’.
Please check also the download section for the
latest firmware version and product
documentation, as these may provide additional
features or easier use of the product.