Denver TFD-2213 User manual

22"TFT LCD TV+DVD COMBO
Operating Instructions
TFD-2213
AC 110-240V 50/60Hz
SCART IN, PC IN
TELETEXT
NTSC PLAYBACK
INSIDE DVD
SUPPORT FORMAT: SVCD, VCD, WMA, HDCD,
KODAK PICTURE CD, DVD
MPEG4
PAL/SECAM B/G,D/K, I,

TABLE OF CONTENTS
1
3
Table of Contents 1
2
15-16
Specifications
Installation
6
8-9
Setup
Functional Parts(TV)
Remote Control unit
TELETEXT Operations 10
Warnings and Cautions 4-5
7
Functional Parts(DVD)
Rear view of TV set
Remote Control Operation(DVD)
11-12
MENU Screens
13-14
Inital Settings(DVD)
17
18
Troubleshooting Tips
The Causes of interference
6
7

SPECIFICATIONS
2
REMOTE CONTROL
Transmitting System :Infrared
Power Supply :DC 3V
Receiving System:
Colour System:
LCD Panel: 558.8mm(22 inch) diagonal
Ext.Antenna:
Ext. In/Out:
Speaker:
Audio Output:
75 Ohm Coaxial Cable
HDMI,YPbPr,AV,PC Input, SCART IN,Earphone
8 Ohm
Dimension:
Net Weight:
W530 xD196 xH435(mm)
5.4KG
3W x 2
Note:Design and specifications are subject to change without prior notice.
B/G,D/K,l,L/L,,
, (Optional)
PAL,SECAM,(optional)
Power Supply: AC 110-240V 50/60Hz
Power consumption: 60W
Standby power consumption: 3W
OPEN/CLOSE POWER
P.PP.P
SWAPSWAP
Q.
VIEW
Q.
VIEW
REPEAT
MUTE SOURCE
MENU
PROG+
PROG-
VOL+
VOL-
REVEAL SIZE STOP
INDEX TEXT
MIX
DVDMENU PROGRAM SUBTITLE
AUDIO
DISPLAY
DVDSETUP GOTO
ENTER
-/---/--
ANGLE SLOW TITLE ZOOM
SUB.PAGE
ASPECT S.M

3
Thank you verymuch for yourpurchase of thisproduct, the mostnatural Colour TelevisionReceiver.
To enjoy yourset to thefull from thevery beginning, readthis manual carefullyand keep ithandy for ready
reference.
INSTALLATION
Locate the receiverin the room where direct light does not strike the screen.
Total darkness ora reflection onthe picture screen can cause eyestrain. Soft and indirect lighting is
recommended for comfortableviewing.
Allow enough spacebetween the receiver and the wall to permit ventilation.
Avoid excessively warmlocations to prevent possible damage to the cabinet or premature component
failure.
This TV operateson a DC supply provided by the AC-DC adaptor. The voltage is as Indicated on the label
on the backcover.Only use theAC-DC adaptor supplied with the TV and never apply an AC mains to the TV
directly. The AC-DCadaptor operates onand AC mains supply, the voltage is as indicated on the label of
the AC-DC adaptor.Connect the DCplug of the AC-DC adaptor to the DC 12V socket at the back of the TV.
Connect the AC-DCadaptor and itsmains cord. Insert the mains plug in the wall socket having a mains
voltage of 110-240V.
Do not installthe receiver ina location near heat sources such as radiator, air ducts, direct sunlight ,or
in a placesomewhere like closecompartment and close area.
Do not coverthe ventilation openingswhen using the set.
CAUTION
Never tamper withany components insideyour set, orany other adjustmentcontrols not mentionedin
this manual. TheLCD panel usedin this productis made ofglass. Therefore,it can break When the product
is dropped orapplied with impact.Be careful notto be injuredby broken glass pieces in case the LCD panel
breaks.When you cleanup dust orstick of awater drop onthe LCD panel. The power cord should be pulled
out from theplug receptacle, thenwipe the receiverwith dried softcloth .During thunderand lighting ,
unplug the powercord and antennacord to preventyour TV setfrom damage. Alltelevision receivers are
high voltage instruments.All "inside work"on your receivershould be performedonly by theTV service
personnel.
If some abnormalphenomena happens ,may be youhave some mis-opertion,pleasetake off powerand
restart your TVset .
INSTALLATION
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE AND OBJECTS FILLED WITH LIQUIDS,
SUCH AS VASES, SHOULD NOT BE PLACED ON THIS APPARATUS.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lighting flash with arrow head within a triangle is intended to tell the user that
parts inside the product are a risk of electric shock to persons.
The exclamation point within a triangle is intended to tell the user that important
operating and servicing instructions are in the papers with the appliance.
IMPORTANT SAFETY INSTRUCTION

4
Caution
Do not dropor push objectsinto the television
cabinet slots oropenings. Never spillany kind
of liquid on the television receiver.
Caution
Do not insertanything in theventilation holes. If
metal or somethingflammable enters, itmay result in
fire or electricshock.
Caution
Do not placeobjects on thisunit, it
may damage thescreen surface.
Caution
Do not squashpower supply cord under the
television receiver.
WARNINGS AND CAUTIONS
Caution
Do not throwanything at theset. The screenglass
may explode byimpact and causeserious injury.
Caution
Never stand on,lean on, orsuddenly push the
television or itsstand. You should pay special
attention to children.Serious injury may result if it
should fall.
Caution
Do not placeyour television onan unstable
cart , stand, shelf ortable. Serious injuryto
an individual, anddamage to the television,
may result ifit should fall.
Caution
When the televisionreceiver is notused for an
extended period oftime, it isadvisable to disconnect
the AC powercord from the AC outlet .

Caution
Do not blockthe ventilation holesin the back
cover. Adequate ventilationis essential to
prevent failure ofelectrical component.
Avoid exposing thetelevision receiver todirect
sunlight and othersource of theheat. Do notstand
the television receiverdirectly on otherproduces
which give offheat .E.g.video cassetteplayers.
Audio amplifiers. Donot place nakedflame sources,
such as lightedcandle on thetelevision. Do not
expose the LCDscreen surface tothe sun, itmay
damage the screensurface.
Warning
WARNINGS AND CAUTIONS
5
Take care notto connect manyappliances to the
same mains socketas this could result in fire or
electric shock.
Warning
High voltages areused in theoperation of this
television receiver.Do notremove the cabinet
back from your set. Refer servicingto qualified
service personnel.
Warning
To prevent fireor electrical shockhazard, Do not
expose the televisionreceiver to rainor moisture.
Warning
For you ownsafety, Do nottouch any part of the set,
main lead oraerial lead duringlighting storms.
Warning
Caution
If the televisionis to bebuilt into aCompartment or
similarly enclosed, theminimum distances mustbe
maintained. Heat build-upcan reduce theservice
life of yourtelevision, and canalso be dangerous.

¼ò ½é¼ò ½é
SETUP
6
Remote Control Battery Installation
4. If you cause a static discharge when touching the unit, and the unit fails tofunction, simply unplug the
unit from the AC outlet,wait a few minutes, andplug it back in. Theunit should return to normaloperation.
Requires two AAA batteries(supplied).
Procedure
1. Turn the remote control face down. Remove battery cover by pressing down on the marking on the
cover and sliding it off in the direction indicated.
2. Install batteries matching(+) and(-) polarity signs.
3. Replace the battery cover by sliding in reverse until the lock snaps.
Note: Incorrect installation can cause battery leakage and corrosion that will damage the Remote control.
Precautions
Replace batteries in pair.
Do not mix battery types(zinc carbon with alkaline).
Do not recharge, heat, short-circuit, disassemble, or burn batteries.
To turn theTV power ON
Put the TVset on thecorrect place, thenconnect the DCplug of the AC-DC adaptor to the DC 12V socket
at the backof the TVset. Connect theadaptor main cordto the wall outlet ,then the LED indicator lamp
turns red/green andthe TV setis at Standby/work Mode. At StandbyMode, if StandbyButton is pressed
the power indicatorwill change togreen. It takesa few secondsbefore the picture appears.
To turn theTV power OFF
Press the StandbyButton to makethe TV setin Standby Mode, then disconnect the power plug from the
wall outlet.
FUNCTIONAL PARTS(TV)
Front View ofLCD Set
NOTE
If TV isthe selected inputwithout
signal received andNO operation
is performed forabout 5 minutes
continuously, the TVset will enter
standby mode. Forany inputs other
than TV, theTV set willnot enter
standby mode automaticallywithout
users instruction. Ifyou are not
going to usethis TV setfor a long
time, switch offthe set and
disconnect the powerplug from
the wall outlet.
2. Remote Sensor
1. LED indicator lamp
3. Standby Button
4. SOURCE Button
5. MENU Button
6. P+ Button
7. P- Button
8. V+Button
9. V- Button
9 8 7 6 5 4
1
¼ò ½é¼ò ½é
3 2

FUNCTIONAL PARTS(DVD)
7
Once you insertthe disk to DVDslot, the player will suck it in, and the current source will be switched
to DVD statusautomatically.
Notes:
1.Do not attachany seal or label to either side (the labeled side or the recorded side) of a disc.
2.Do not useirregularly shaped CDs (e.g., Heartshaped or octagonal)since they may result in
malfunctions.
3.Some playback operationsof DVDs and Video CDs may be intentionally programmed by software
manufacturers. This unit plays DVDS and Video CDs according to disc content designed by the
software manufacturer, thereforesome playback features may not be available or other functions
may be added.
REAR VIEW OF TV SET
NOTE
Precautions when connecting to other equipment
When using external equipment with this TV set, please read the instruction manual of the external equipment.
Switch off all power supplies to the equipment and TV set before connection.
Always ensure that the input and output terminals are correctly connected.
ANT. VGAPC-A IN SCART VIDEO
L R
Y Pb
Pr
HDMI DC-12V
TO DC IN 12V
TO POWER SOURCE
1
2
34
4. Open/Close
1. DVD Slot
3. Stop
2. Play/Pause

REMOTE CONTROL UNIT
POWER ON/STANDBY button
Press this button to switch on the TV when at standby mode orenter
standby mode.
MUTE button
Press this button to mute or restore sound.
P.P Button
Press this button to select the desired picture mode:
NORMAL/SOFT/DYNAMIC/CUSTOM
DISPLAY Button
Press this button to display the setting on the screen.
SLEEP Button
Press this button to set the sleep timer, the order
shown below(minutes):
OFF - 15 - 30 - 45 - 60-120
When the preset length of time has passed, the TV set
enters standby mode.
SOURCE Button
Press ¡°SOURCE¡± button,there will be some word show on the right
top of the screen, press ¡°PROG+/-¡± to select the AV source,and then
press ¡°VOL+/-¡±to enter AV mode.
DIGIT Button(0-9)
This TV allows you to select channels from 1 to 254.
Press this button to select one-digit,two digit or three -digital channels
input options.
To select a one-digit channel(e.g. Channel 8),press this ¡°-/--¡±button
to change channel selection to ¡°-¡±on screen display andpress the
¡°8¡±button only.
To select a two-digit channel(e.g. Channel 28),press this ¡°-/--¡±button
to change channel selection to ¡°--¡±on screen display and press¡°2¡±
and ¡°8 ¡± buttons. To select a three-digit channel(e.g. Channel 128),
press this¡°-/--¡±button to change channel selection to ¡°---¡±on screen
display and press¡°1¡±,¡°2¡±and ¡°8¡± buttons.
8
P.PP.P
TV
AV
DVD
YPBPR
PC
HDMI
SCART
OPEN/CLOSE POWER
P.PP.P
SWAPSWAP
Q.
VIEW
Q.
VIEW
REPEAT
MUTE SOURCE
MENU
PROG+
PROG-
VOL+
VOL-
REVEAL SIZE STOP
INDEX TEXT
MIX
DVD MENU PROGRAM SUBTITLE
AUDIO
DISPLAY
DVD SETUP GOTO
ENTER
-/---/--
ANGLE SLOW TITLE ZOOM
SUB.PAGE
ASPECT S.M

FROM CH 1
TO CH 7
SAVE
MENU Button
Press this button to enter the menu screens for various optional
adjustable settings.
PROG+/- Button
Press the program up button to select the program forwards. Press
the program Down button to select the program Backwards.
VOL+/- Button
Press volume up/down buttons to adjust sound level.
Q.VIEW Button
Press this button to return to the previously viewed program.
SWAP Button
You can adjust your TV program list order, press this button, the
program swap menu will displayed, as shown below. E.g. to swap
channel 1 and 7 , press¡°SWAP¡± button, press¡°PROG+/-¡± to
choose .FROM and press ¡°VOL+/-¡± to set the channel number as
¡°0¡±,and as the sameway to set the TO as¡°7¡±,last to do choose
the¡°SAVE¡± and press ¡°VOL+/-¡± to implement this fuction.
REMOTE CONTROL UNIT
9
ASPECT Button:
Press this button to selectscaler mode:
16:9 4:3 ZOOM 16:9FS PANORAMA
S.M Button:
Press this button to selectthe sound mode:
NORMAL/NEWS/MUSIC/CUSTOM
OPEN/CLOSE POWER
P.PP.P
SWAPSWAP
Q.
VIEW
Q.
VIEW
REPEAT
MUTE SOURCE
MENU
PROG+
PROG-
VOL+
VOL-
REVEAL SIZE STOP
INDEX TEXT
MIX
DVD MENU PROGRAM SUBTITLE
AUDIO
DISPLAY
DVD SETUP GOTO
ENTER
-/---/--
ANGLE SLOW TITLE ZOOM
SUB.PAGE
ASPECT S.M

TEXT Button
Press this button to enter or exit the teletext mode.
INDEX Button
Press the button to go to the index page.
REVEAL Button
Press this button to reveal the hidden information for
some Teletext pages(e.g. answers to puzzles or riddles).
Press again to hide the information.
MIX Button
Press this button enter to mix mode.(For SUBTITLE or
NEWSFLASH page, please use mix mode).
Press this button again to exit.
SIZE Button
Press this button to change the Teletext screen display
mode among the following:
- Upper half screen enlarged
- Lower half screen enlarged
- Normal screen state
STOP Button
Press this button to hold the Teletext page on display to prevent the
page from changing. Press again to release the hold state.
SUB.PAGE (Optional)
Press this button to display subpage.
TELETEXT OPERATIONS (OPTIONAL)
For models withTeletext function only.
10
NO SILK BUTTONS:
Have no function£¡
OPEN/CLOSE POWER
P.PP.P
SWAPSWAP
Q.
VIEW
Q.
VIEW
REPEAT
MUTE SOURCE
MENU
PROG+
PROG-
VOL+
VOL-
REVEAL SIZE STOP
INDEX TEXT
MIX
DVD MENU PROGRAM SUBTITLE
AUDIO
DISPLAY
DVD SETUP GOTO
ENTER
-/---/--
ANGLE SLOW TITLE ZOOM
SUB.PAGE
ASPECT S.M

REMOTE CONTROL OPERATION(DVD)
11
OPEN/CLOSE POWER
P.PP.P
SWAPSWAP
Q.
VIEW
Q.
VIEW
REPEAT
MUTE SOURCE
MENU
PROG+
PROG-
VOL+
VOL-
REVEAL SIZE STOP
INDEX TEXT
MIX
DVD MENU PROGRAM SUBTITLE
AUDIO
DISPLAY
DVD SETUP GOTO
ENTER
-/---/--
ANGLE SLOW TITLE ZOOM
SUB.PAGE
ASPECT S.M
DVD Mode:
OPEN/CLOSE Button
Press OPEN/CLOSE buttonto load discon disc tray.
PREV/NEXT Button
Press these buttonto go tothe previous/next chapter(DVD).
FR/FF Button
These buttons allowskipping ahead/back at5-level speed. Press
¡°PLAY¡±button to return to normal playback.
REPEAT Button
To press thisbutton you canrepeatedly play atitle(DVD) or all
tracks(CD) .
PLAY/PAUSE Button
Press this buttonto start playback.Press this buttonagain to
pause playback.
STOP Button
Press this buttonto stop DVDplayer.
TITLE button
DVD disc:
Press TITLE button,then you canuse " "and ENTER buttonto
select programs.
VCD disc:
Press TITLE button,youcan switch PBCon/off.
ZOOM button
Press ZOOM duringplayback or stillplayback to activatethe Zoom
function.
Note:Zoom may notwork on someDVDs.
ANGLE button
If the disccontains scenes recordedat different cameraangles,
you can changeto a differentcamera angle duringplayback.
Note:The angle indicatorwill blink onthe TV screenduring
scenesrecorded at differentangles as anindication that angle

REMOTE CONTROL OPERATION(DVD)
12
OPEN/CLOSE POWER
P.PP.P
SWAPSWAP
Q.
VIEW
Q.
VIEW
REPEAT
MUTE SOURCE
MENU
PROG+
PROG-
VOL+
VOL-
REVEAL SIZE STOP
INDEX TEXT
MIX
DVD MENU PROGRAM SUBTITLE
AUDIO
DISPLAY
DVD SETUP GOTO
ENTER
-/---/--
ANGLE SLOW TITLE ZOOM
SUB.PAGE
ASPECT S.M
DVD Mode:
SLOW Button
Press this buttonduring playback toactivate the slowfunction.
DVD MENU Button
If play someDVD discs, pressthis button backto root menu screen.
PROGRAM Button
Place a trackon the programlist.
SUBTITLE Button
To press thisbutton, you canchange the subtitlelanguage from
one selected tothe initial settingsto a differentlanguage, if
available.
AUDIO Button
To press thisbutton, you canchange the audiolanguage from the
one selected atsettings to adifferent language, ifavailable.
DVD SETUP Button
Accesses or removessetup menu.
DISPLAY Button
To display playerOSD.
GOTO Button
Press this buttonto go todesired position.

SOUND
BASS
TREBLE
BALANCE
SOUND MODE NORMAL
PC
PC
MOVE SELECT EXIT
TUNE
PC
PC
MOVE SELECT EXIT
AUTO SCAN
MANUAL PROGRAM
PROGRAM LIST
COUNTRY FRANCE
PICTURE
16:9
PC
PC
MOVE SELECT EXIT
PICTURE MODE NORMAL
ASPECT
MENU SCREENS
PICTURE MENU
You can adjust the contrast, brightness, tint(NTSC only) colour,sharpness.
COLOUR TEMP: NORMAL / WARM / COOL
APPECT: 16:9/4:3/ZOOM/16:9FS/PANORAMA
PICTURE MODE: NORMAL/SOFT/DYNAMIC/CUSTOM
SOUND MENU
Enter sound menu, you can adjust.
SOUND BASS/TREBLE/BALANCE/SOUND MODE:
NORMAL/NEWS/MUSIC/CUSTOM
TUNE MENU
COUNTRY: Select correct before auto searching,then
you can get right program order.
AUTO SCAN: Press¡°VOL+/-¡±to begin auto search
program, and press menu to exit auto search.
MANUAL PROGRAM: To enter manual setting
sub menu.
PROGRAM LIST: To edit program.
CHANNEL: The number is the current channel, and you
can also change channel from one to another.
COLOUR SYS. AUTO/PAL/SECAM (optional)
SOUND SYS. B/G,D/K,I,L,L¡¯(optional)
SKIP: Set this item on to skip the channel which you
are Watching.
Fine Tune: Frequency data can be fine-tuned in upward
or downward by the VOL+/- buttons.
This TV allows you to adjust any setting from the menu screens using ¡°MENU¡±,¡°VOL+/-¡±and ¡°PROG+/-¡±
buttons.
Press ¡°MENU¡±button to display the menu, press¡°PROG+/-¡±to change menu from one to another, ¡°VOL+/-¡±
to enter the chosen menu, press¡°PROG+/-¡±to select the item, and then press ¡°VOL+/-¡±to adjust each
item.
Press ¡°MENU¡± again to exit the menu mode.
13
PICTURE
BRIGHTNESS
HUE
COLOUR
SHARPNESS
COLOUR TEMP NORMAL
CONTRAST
MOVE SELECT EXIT
PC
PC

PC
PC
PC
MOVE SELECT EXIT
AUTO CONFIG
COLOUR TEMP
PC
BRIGHTNESS
CLOCK
PHASE
CONTRAST
MOVE SELECT EXIT
PC
PC
H-POSITION
V-POSITION
OSD
H-POSITION
DURATION
LANGUAGE ENGLISH
PC
PC
MOVE SELECT EXIT
HALFTONE
V-POSITION
OSD SIZE 2 TIMES
SETUP
TXT LANGUAGE WEST
PC
PC
MOVE SELECT EXIT
NOISE REDUCE
BLUE SCREEN
ON
OFF
OSD MENU
You can choose the language, adjust the H-position,
V-position, duration 1 halftone and size..
NOTE:
If the set is cold ,there may be a small¡°flicker¡± when the set isswitched on. It is normal, There is nothing
wrong with the set.
If possible, use the VESA 1024X768@60HZ video mode to obtain the best image quality for your LCD monitor.
Under other resolutions some scaled or processed pictures may appear on the screen.
Some dot defects may appear on the screen, like red, green or blue Spots, However,this will have no impact
or effect on the monitor performance.
Do not press the LCD screen with your finger for a long time as it may incur some damage to the screen.
MENU SCREENS
14
SETUP MENU
TXT LANGUAGE.You can choose the supported
teletext fonts among AUTO,WEST,EAST,RUSSIAN,
ARABIC and FARSI.
NOISE REDUCE: You can set the noirse filter to ON or OFF.
BULE SCREEN: You can set background ON or OFF.
You can set the picture display mode 16:9,
4:3 ,ZOOM,and 16:9FS,PANORAMA.
PC MENU(under PC mode only)
You can adjust the CONTRAST, BRIGHTNESS
H-POSITION/V-POSITION: Press the VOL+/- buttons to adjust the picture Horizontal and Vertical position.
CLOCK : Press the VOL+/- to minimize any vertical bars or stripes visible on the screen background.
PHASE : When necessary, adjust the pixel phase of the picture to avoid picture interference.
AUTO CONFIG : To adjust the screen position automatically. It will take a few seconds and during this
process the screen will be black.
COLOUR TEMP: To ADJUST the PC mode color temperature.

INITAL SETTINGS(DVD)
15
COMMON PROCEDURES OF INITIAL SETTINGS
Press SETUP button to get the setup menu. Use
direction buttons " " to select the preferred item .
After finishing settings, press SETUP again to TV
display.
The following menu items can be changed:
GENERAL: Selects the GENERAL SETUP PAGE menu.
AUDIO : Selects the AUDIO SETUP PAGE menu.
DOLBY : Selects the DOLBY DIGITAL SETUP PAGE
menu.
PREFERENCE: Selects the PREFERENCE SETUP PAGE
menu.
PASSWORD: Selects the PASSWORD SETUP PAGE
menu.
The following me u items can be changed:
TV DISPLAY: Selects the aspect ratio of the playback
picture.
4:3 PanScan: Pan Scan display.
4:3 LetterBox: LetterBox display.
16:9
n
&
: widescreen display.
ANGLE MARK: Viewing angles change option
(if available).
SCREEN SAVER: This is to turn on/off screen saver.
CLOSED CAPTIONS:Closed captions are data that are
hidden in the video signal of some discs.Before you
select this function,please ensure that the disc contains
closed captions information and your TV set also has
this function.
Dolby
The following menu items can be changed:
DUAL MONO: Reproduction mode, used only when the
input consists of two independent audio
channels(1/1 mode). Possible selections
are:
STEREO: Reproduce both channels as is.
L-MONO: Reproduce the left channel only.
R-MONO: Reproduce the right channel only.
The default is STEREO.
DYNAMIC: Dynamic range compression.
DOLBY DIGITALSETUP PAGE
Dual Mono
Dynamic
Dolby Digital Setup
-- --
Go To Dolby Digital Setup
Stereo
L-Mono
R-Mono
Mix-Mono
FULL
3/4
1/2
1/4
OFF
DOWNMIX Stereo
LT/RT: 2ch output, main channel with surround.
STEREO: 2ch output, main right channel with right
surround; main left channel with left surround.
LT/RT
Stereo
Downmix
Analog Audio Setup Page
-- --
AUDIO SETUP PAGE
This page is for setup speaker output.
Go To Speaker Setup Page
Stereo
Dolby
GENERAL SETUP PAGE
Go To General Setup Page
General Setup Page
-- --
TV Display Ps
Angle Mark On
Osd Lang Eng On
Off
Screen Saver On
On
Off
Closed Captions On On
Off
English
French
German
Italian
Spanish
Portuguese
4:3 PanScan
4:3 LetterBox
16:9
Dolby

INITAL SETTINGS(DVD)
16
The following menu items can be changed:
AUDIO: Selects a language for audio(if available).
SUBTITLE: Selects a language for subtitles(if available).
DISC MENU: Selects a language for DISC menus (if available).
PARENTAL[DVD only]: This is to disable the playing of specified DVDs which are unsuitable for children. Some
DVDs are encoded with specific rating level. If the rating level of the disc is higher than that preset in the setup
operation, playback of the disc will be prohibited. After selecting one of the PARENTAL items the screen will
change to the PASSWORD page, and password is required , The factory initial setting is 1369.
DEFAULT:Back to the factory setting.
Audio Eng
Subtitle
Disc Menu Eng
Parental
Default
Preference Page
-- --
Go To Preference Page
1 Kid
2 G
3 Pg
4 Pg 13
5 Pgr
6 R
7 Nc17
8 Adult
Reset
PREFERENCE SETUP PAGE
English
French
Spanish
Chinese
Japanese
Korean
Russian
English
French
Spanish
Chinese
Japanese
Korean
Russian
English
French
Spanish
Chinese
Japanese
Korean
Russian
Dolby
Eng
PASSWORD MODE: Set password modeon/off. If setto off, changeparental level willnot check password.
PASSWORD: Select the menupassword change page.
PASSWORD SETUP PAGE
Dolby
- - Password Setup Page - -
PASSWORD MODE ON
PASSWORD
ON
OFF
Go To Password Setup Page
OLD PASSWORD: Enter the OLDpassword, (Factory settingis 1369), andthe cursor will jump
automatically to NEWPASSWORD
NEW PASSWORD: Enter the NEWpassword. Enter 4digits from theremote control unitnumeric buttons,
and the cursorwill automatically jumpto CONFIRM PASSWORD.
CONFIRM PASSWORD: Confirm the NEWpassword by entering it again. Ifthe confirmation isincorrect,
the cursor willstay in thiscolumn. After entering,the correct newpassword again, thecursor will jump
automatically to OK.
OK: When cursor ison this button,press ENTER keyto confirm setting.
Note: If thepassword has beenchanged, the parentalanddisc lock codewill also bechanged.
The default password(1369)isalways active eventhe password hasbeen changed.
N
OLD PASSWORD
NEW PASSWORD
CONFIRM PWD
OK
Dolby

TROUBLESHOOTING TIPS
Before calling forservice, you cancheck the followingitems on symptomsand solutions.
No picture:
Check other channel,maybe station problem.
Adjust the tuningcontrol.
Ensure that theinput setting isat TV state.
Ensure that theLCD is on.
Ensure that theequipment is connectedproperly.
No sound anddistorted sound:
Ensure that theinput settings forthe TV andsound are proper.
Adjust the tuningcontrol.
Probably local interference,such as anappliance.
Re-orient aerial(if indoortype).
Ensure that theequipment is connectedproperly.
No remote Control:
Check the batteryare installed withthe correct polarity.
Point the remotecontrol unit atthe remote controlsensor and operate.
Remove the obstaclesbetween the remotecontrol and theremote control sensor.
Operate the remotecontrol unit ata distance ofnot more than8 meters fromthe remote controlsensor.
Troubleshooting tips(PC mode):
¡°NO SIGNAL¡±displayed
Check if thewire is connectedcorrectly.
Ensure the computeror other equipmentsare at poweron mode.
Ensure the computeris not atpower save mode.
Ensure the TVinput setting isat pc mode.
¡°UNSUPPORTED¡±displayed
Check if theinput setting iscompatible to themonitor specification.
Check if thewire is connectedcorrectly.
Led lamp indicatoron but nopicture
Check the monitorsetting :contrast ,brightness.
Check if thewire is connectedcorrectly.
Some unusual spotson screen:
Some dot defectsmay appear onthe screen, likered, green orblue, Spots, However,this will haveno
impact or effecton the monitorperformance.
17

Incorporated in yourTV receiver arethe most up-to-datedevices to eliminateinterference.Local radiation
however, can createdisturbances which visiblyaffect your picture.Proper installation, agood aerial are
your best safe-guardsagainst these disturbances.
RF INTERFERENCE
Moving ripples acrossthe screen arecaused by nearbytransmitting or receivingshort-wave radio
equipment.
DIATHERMY
Herringbone pattern andpartial picture losscan result fromthe operation ofdiathermy equipment froma
nearby doctor's surgery orhospital.
SNOW
Weak TV signalsfrom long distantstations result inan instead pictureand give theeffect of fallingsnow.
An antenna adjustmentor antenna amplifiermay be needed.
GHOST
Multiple image causedby TV signalsreflected back fromsurrounding buildings, hills,aircraft, ect. Is
minimized by correctaerial positioning.
CAR IGNITION
Nearby cars andelectrical motors cancause small streaksacross the pictureor make the picture roll.
THE CAUSES OF INTERFERENCE
18