Desoutter EAB 15-900 Instruction sheet

Printed Matter No. 6159929380_EN
Issue No. 01
Date 06/2020
Page 1 / 24
Cordless Angle Nutrunner
Product Instructions
Model Part number
EAB 15-900 6151657310
EAB 26-560 6151657320
EAB 32-410 6151657330
EAB 45-330 6151657340
EAB 50-450 6151657350
EAB 60-370 6151657360
EAB 75-300 6151657370
EAB 95-240 6151657380
Download the latest version of this document at
http://www.desouttertools.com/info/6159929380_EN
WARNING
Read all safety warnings and instructions
Failure to follow the safety warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference

2 / 24 06/2020
Table of Contents
Product Information ..............................................................................................................................3
General Information.........................................................................................................................3
Warranty...............................................................................................................................3
Website ................................................................................................................................3
Information about spare parts ..............................................................................................3
Dimensions (mm) .................................................................................................................3
CAD files ..............................................................................................................................4
Overview .........................................................................................................................................4
General overview .................................................................................................................4
Product description ..............................................................................................................4
Technical data......................................................................................................................5
Accessories..........................................................................................................................6
Installation..............................................................................................................................................7
Installation Instructions....................................................................................................................7
Inserting the battery pack.....................................................................................................7
How to connect the tool to CVIMONITOR............................................................................7
How to install optional accessories ......................................................................................7
Operation................................................................................................................................................8
Configuration Instructions................................................................................................................8
How to configure the tool .....................................................................................................8
Operating Instructions ...................................................................................................................11
How to use the tool ............................................................................................................11
Results monitoring .............................................................................................................13
Service..................................................................................................................................................15
Firmware version on tool display...................................................................................................15
Tool information from tool display .................................................................................................15
Tool test with CVIMONITOR .........................................................................................................15
Tool identification with CVIMONITOR ...........................................................................................15
Maintenance Instructions ..............................................................................................................15
Instructions for transducerized tools ..................................................................................15
Read before maintenance..................................................................................................15
Preventive Maintenance.....................................................................................................16
Service alarm on tool display ........................................................................................................16
Calibration via tool display.............................................................................................................17
Calibration with eDOCK and CVIMONITOR .................................................................................17
Checking before putting back into service.....................................................................................17
Advanced tool maintenance with ACCESS KEY...........................................................................17
Motor align .........................................................................................................................18
Declaring fixed accessories ...............................................................................................18
Upgrading tool firmware .....................................................................................................18
Troubleshooting ..................................................................................................................................19
List of user infos related to the tools..............................................................................................19

EN Product Information
06/2020 3 / 24
Product Information
General Information
WARNING Risk of Property Damage or Severe Injury
Ensure that you read, understand and follow all instructions before operating the tool. Failure to follow all the
instructions may result in electric shock, fire, property damage and/or severe bodily injury.
►Read all Safety Information delivered together with the different parts of the system.
►Read all Product Instructions for installation, operation and maintenance of the different parts of the system.
►Read all locally legislated safety regulations regarding the system and parts thereof.
►Save all Safety Information and instructions for future reference.
Warranty
• Product warranty will expire 12 months after the product is first taken into use, but will in any case expire at the
latest 13 months after delivery.
• Normal wear and tear on parts is not included within the warranty.
• Normal wear and tear is that which requires a part change or other adjustment/overhaul during standard tools
maintenance typical for that period (expressed in time, operation hours or otherwise).
• The product warranty relies on the correct use, maintenance, and repair of the tool and its component parts.
• Damage to parts that occurs as a result of inadequate maintenance or performed by parties other than Desoutter
or their Certified Service Partners during the warranty period is not covered by the warranty.
• To avoid damage or destruction of tool parts, service the tool according to the recommended maintenance sched-
ules and follow the correct instructions.
• Warranty repairs are only performed in Desoutter workshops or by Certified Service Partners.
Desoutter offers extended warranty and state of the art preventive maintenance through its Tool Care contracts. For
further information contact your local Service representative.
For electrical motors:
• Warranty will only apply when the electric motor has not been opened.
Website
Information concerning our Products, Accessories, Spare Parts and Published Matters can be found on the Desoutter
website.
Please visit: www.desouttertools.com.
Information about spare parts
Exploded views and spare parts lists are available in Service Link at www.desouttertools.com.
Dimensions (mm)
L ØA ØB ØC
EABx 15-900 470 46 46 37
EABx 26-560 496 46 46 37
EABx 32-410 496 46 46 37
EABx 45-330 506 46 46 37

Product Information EN
4 / 24 06/2020
EABx 50-450 546 46 46 37
EABx 60-370 559 46 58 41
EABx 75-300 582 46 58 48.5
EABx 95-240 582 46 58 48.5
D E F G
EABx 15-900 1/4" 28 12 46
EABx 26-560 3/8" 28 12 46
EABx 32-410 3/8" 28 12 46
EABx 45-330 3/8" 35 12 51
EABx 50-450 3/8" 35 12 51
EABx 60-370 1/2" 40 12 57
EABx 75-300 1/2" 45 18 60
EABx 95-240 1/2" 45 18 60
EABx stands for EAB/EABA.
CAD files
For information about the dimensions of a product, see the Dimensional drawings archive:
https://www.desouttertools.com/resource-centre
Overview
General overview
EAB tools are cordless angle-head nutrunners.
They are hand-held by the operator and powered by a Desoutter battery pack.
On delivery, the tool display is protected by a password.
Tools are delivered with 1 Pset.
The target torque is configurable from the tool display.
The last 100 results can be displayed on the computer for analysis with CVIMONITOR.
Tool settings can be done via the tool display.
Tool maintenance can be done with eDOCK and CVIMONITOR software.
Product description
1 Output drive
2 Reporting LEDs

EN Product Information
06/2020 5 / 24
3 Trigger
4 Battery footprint
5 Display
6 Programming buttons
7 Reverse button
Technical data
Voltage (V)
36 V
Output drive
Model Type
EABx 15-900 Sq. 1/4"
EABx 26-560 Sq. 3/8"
EABx 32-410 Sq. 3/8"
EABx 45-330 Sq. 3/8"
EABx 50-450 Sq. 3/8"
EABx 60-370 Sq. 1/2"
EABx 75-300 Sq. 1/2"
EABx 95-240 Sq. 1/2"
EABx stands for EAB/EABA/EABC.
Torque range (Nm)
Model Min. / Nominal / Max.
EABx 15-900 5 / 13 / 15
EABx 26-560 5 / 24 / 26
EABx 32-410 7 / 30 / 32
EABx 45-330 9 / 40 / 45
EABx 50-450 9 / 45 / 50
EABx 60-370 10 / 55 / 60
EABx 75-300 12 / 70 / 75
EABx 95-240 19 / 90 / 95
EABx stands for EAB/EABA/EABC.
Torque range (ft.lb)
Model Min. / Nominal / Max.
EABx 15-900 3.69 / 9.59 / 11.06
EABx 26-560 3.69 / 17.70 / 19.18
EABx 32-410 5.16 / 22.13 / 23.60
EABx 45-330 6.64 / 29.50 / 33.19
EABx 50-450 6.64 / 33.19 / 36.88
EABx 60-370 7.37 / 40.57 / 44.25
EABx 75-300 8.85 / 51.63 / 55.32
EABx 95-240 14.01 / 66.38 / 70.07
EABx stands for EAB/EABA/EABC.

Product Information EN
6 / 24 06/2020
Rated speed (rpm)
Model rpm
EABx15-900 900
EABx 26-560 560
EABx 32-410 410
EABx 45-330 330
EABx 50-450 450
EABx 60-370 370
EABx 75-300 300
EABx 95-240 240
EABx stands for EAB/EABA/EABC.
Weight
Model (kg) (lb)
EABx 15-900 1.55 3.42
EABx 26-560 1.65 3.64
EABx 32-410 1.65 3.64
EABx 45-330 1.76 3.88
EABx 50-450 2.04 4.50
EABx 60-370 2.35 5.18
EABx 75-300 2.94 6.48
EABx 95-240 2.98 6.57
EABx stands for EAB/EABA.
The weight is given without the battery pack.
Storage and use conditions
Storage temperature -20 to +70 °C (-4 to +158 F)
Operating temperature 0 to 45 °C (32 to 113 F)
Storage humidity 0-95 % RH (non-condensing)
Operating humidity 0-90 % RH (non-condensing)
Altitude up to 2000 m (6562 feet)
Usable in Pollution degree 2 environment
Indoor use only
Accessories
Optional accessories
eDOCK 6158119760
Required accessories
Battery pack 18 V 2.5 Ah 6158132660
Battery pack 36 V 2.5 Ah 6158132670
Battery pack charger 6158132700

EN Installation
06/2020 7 / 24
Installation
Installation Instructions
Inserting the battery pack
Insert the battery pack in front or behind the tool until a locking sound can be clearly heard.
There is no ON/OFF switch: the tool is ready to operate as soon as a battery pack is mounted.
When the tool is powered on, tool LEDs are blinking.
NOTICE Usage recommendations for battery packs
Ensure a longer service life of the battery pack.
►Unplug the battery pack when the tool is not used.
Do not leave the battery pack on the charger when the charger power supply is off.
How to connect the tool to CVIMONITOR
Plug a battery pack to the tool.
Connect eDOCK to the tool and to the USB port of the computer.
Respect the connection order.
Launch CVIMONITOR from the computer desktop.
Click Tool in the top bar.
Click Select to select the tool.
How to install optional accessories
Refer to the user manual dedicated to the accessory available at https://www.desouttertools.com/resource-centre.

Operation EN
8 / 24 06/2020
Operation
Configuration Instructions
How to configure the tool
Icons and buttons
The password is enabled.
The password is disabled.
Press the button "Validate/Run reverse".
Press the right button.
Press the left button.
"Validate/Run reverse" button
Right button
Left button
Validate
Save
Quit
Pset
The sound is disabled.
The sound is enabled.
The battery pack is full.
The battery pack is low.
Additional icons and buttons
Reverse mode: once
The tool will run in reverse once only. To run the tool in reverse again, the operator will have to press the Re-
verse button.
Reverse mode: alternate
The tool will run in reverse until the operator presses the Reverse button again.
This icon blinks when the tool memory is full.
New results will overwrite the oldest results.
How to disable the passwords
On delivery, passwords are enabled (1 by default).
Passwords are used to protect some settings against hazardous changes.
Pset, Ergostop, Pset password, Reverse, Sound, Torque unit are settings protected by the Pset password.

EN Operation
06/2020 9 / 24
Maintenance password, Calibration are settings protected by the Maintenance password.
A red padlock is displayed on the top line of the main screen.
Press this button during 2 seconds.
Press this button to reach Configuration.
Go to Enter password, then Pset password, use the buttons to display "1", save and validate. The red padlock turns
green.
The procedure is the same to disable the Maintenance password.
How to set up new passwords
To set new passwords, current passwords must be disabled and the green padlock displayed.
Go to the main screen.
Press this button during 2 seconds.
Press this button to reach Configuration.
Go to Set password, then Pset password, use the buttons to enter a figure from 0 to 999, save and validate.
Setting the password to 0 will disable all password protections.
The procedure is the same to set up a new Maintenance password.
Sound, torque unit
Sound
The tool can emit sounds to alert the operator in case of problems or events that may happen during the tightening
operation.
Sounds can be set for the following topics:
• tightening out of tolerances
• calibration procedure
• preventive maintenance
• low battery
• hardware failure
• maintenance
On tool delivery, the sound is disabled.
To enable the sound, go to the main screen.
Press this button during 2 seconds.
Press this button to reach Configuration.
Go to Sound, then No sound, use the buttons to save and validate.
Torque unit
The following torque units are available:
• Nm
• ft.lb
• in.lb

Operation EN
10 / 24 06/2020
• kg.m
• kg.cm
• oz.in
• dNm
To change the torque unit, go to the main screen.
Press this button during 2 seconds.
Press this button to reach Configuration.
Go to Torque unit, use the buttons to select the torque unit and validate.
How to set up the reverse mode
Go to the main screen.
Press this button during 2 seconds.
Press this button to reach Configuration.
Go to Reverse.
Use the buttons to enable or disable the feature.
Select the reverse mode (alternate or once), save and validate.
How to set up the Pset
Check that the Pset password is disabled.
The green padlock is displayed on the top line.
Go to the main screen.
Press this button during 2 seconds.
Press this button to reach Pset.
Use the buttons to navigate, save and validate.
If no action is done, the display returns to the main screen after 15 seconds and the changes will not be saved.
Pressing the trigger at that stage will cancel all modifications done.
Parameter Description
Thread Selection of the thread direction of the screw.
CW: when operating in forward, the tool rotates clockwise.
CCW: when operating in forward, the tool rotates counter-
clockwise.
Target torque The torque value to reach.
Min./max. torque Torque values which define the min./max. torque tolerances.
Min./max. angle Angle values which define the min./max. angle tolerances.
Abort angle 5,000 degrees by default
Start torque This is the torque value that must be reached to declare the
Pset as started.
Below this value, neither result or report will be generated.
Angle threshold This is the torque threshold value used to start counting the
angle (usually 50% of the target torque)
Max. time 30 sec by default. The tool stops when the time is reached.
Motor control

EN Operation
06/2020 11 / 24
Starting at the "Start" signal, the tool runs with a programmed acceleration up to "Rundown speed".
The tool keeps running at "Rundown speed".
Once "Downshift torque" has been reached, the speed changes to "Downshift speed".
Item Parameter Description
1 Pset start torque The Pset start torque is the torque
value that must be reached to declare the
Pset as started.
Below this value, neither result or report
will be generated.
2 Rundown speed Speed applied from the start to "Down-
shift torque".
3 Downshift torque Torque value where the speed moves
from "Rundown speed" to "Downshift
speed".
4 Downshift speed Speed applied from "Downshift torque"
to the motor stop.
Operating Instructions
How to use the tool
Starting the tool
Fit the tool with a suitable socket.
Select the appropriate Pset.
Hold the tool by means of the handle and apply to the fastener to be tightened.
WARNING Risk Of Injury
As the reaction force increases in proportion to the tightening torque, there is a risk of severe bodily injury of the
operator as a result of unexpected behavior of the tool.
►Make sure that the tool is in perfect working order and the system is programmed correctly.
Press the trigger to start the tool.

Operation EN
12 / 24 06/2020
Tightening status and LED reporting
Torque control with angle monitoring
1 Max. torque
2 Target torque
3 Min. torque
4 Downshift torque
5 Pset start torque
6 Angle start
7 Min. angle
8 Max. angle
Examples:
- Both torque and angle within tolerances will lead to a green LED reporting.
- Torque within tolerances and angle below tolerances will lead to red + yellow status (red LED).
For tools running in severe applications, it may happen that reports are null when the battery is low.
Reporting LEDs
1 Red
2 Green
3 Yellow

EN Operation
06/2020 13 / 24
How to read the tightening report
LED color Description Action to do
Green Accept report None
Yellow Incomplete rundown Tighten again.
Yellow and red (orange) Reject report Loosen and tighten again.
Red Above max. limits Remove and replace the fastener.
How to reverse the rotation
1 Run reverse button
Press this button.
Red and green LEDs are blinking alternatively.
Apply the tool to the fastener and press the trigger.
How to smooth the tool stop
The "Ergostop" function must be disabled for tightening tests or certification on tightening benches.
Ergostop allows a smoother tool stop to reduce the torque reaction on the operator.
When delivered, this function is disabled.
Go to the main screen.
Press this button during 2 seconds.
Go to Ergostop. Use the buttons to enable or disable the function, save and validate.
How to wake up EAB tools
The tool display switches off automatically after 2 minutes of inactivity.
Press the trigger.
The tool powers off after 30 minutes of inactivity.
Long press the reverse button.
Refer to "Power off" configurable on the tool display.
Unplug and plug the battery pack.
Results monitoring
Connect the tool to a PC by using the eDOCK device.

Operation EN
14 / 24 06/2020
Launch CVI MONITOR to collect and display the last 100 results.
Refer to the user manual of CVIMONITOR available at https://www.desouttertools.com/resource-centre.

EN Service
06/2020 15 / 24
Service
Firmware version on tool display
The firmware version of the tool is displayed in the menu "Maintenance/Tool".
FX.YY.ZZ.
Tool information from tool display
Go to "Maintenance/Tool" menu to get the following information:
Total counter Number of tightenings since the manufacturing of the tool.
Battery The current voltage value is displayed.
The "Low battery" message is displayed when lower than 32
V.
At 31 V, the tool stops.
Serial number 18B64685 for example.
Tool test with CVIMONITOR
Click this icon.
Click Tool test.
Click Start tool test.
LEDs start blinking.
Press the triggers, the reverse button.
Click Start audio test.
The tool emits a sound.
The green tick displayed indicates the function is working properly.
Tool identification with CVIMONITOR
Click this icon.
Click Tool identification.
Go to the bottom of the screen and click Read tool.
A green tick indicates the reading is successful.
Maintenance Instructions
Instructions for transducerized tools
• Do not damage the wires when pulling out the connectors.
• Do not pull out the torque transducer wires.
• Ensure that wires are not crushed.
Read before maintenance
WARNING Connection Hazard
The tool can start unexpectedly and cause severe bodily injury.
►Prior to any maintenance task, disconnect the tool.
Maintenance should be performed by qualified personnel only.
Follow standard engineering practices and refer to exploded views for disassembling and reassembling the different
parts of the system.

Service EN
16 / 24 06/2020
Take into account the following instructions given in the exploded views.
Be cautious: when reassembling, tighten the right direction.
Left hand thread
Right hand thread
When reassembling:
Apply the recommended glue.
Tighten to the required torque.
Lubricate with the required grease or oil. Do not apply too much grease on gears or bearings; a thin coat shall be
sufficient.
Preventive Maintenance
Recommendations
Overhaul and preventive maintenance are recommended at regular intervals once per year or after a maximum num-
ber of tightenings (refer to the table below) depending on which occurs sooner.
Maintenance frequency
500,000 tightenings
Service alarm on tool display
An alarm can be displayed when service is required.
This icon is displayed.
One of the service levels is displayed (see below). When no service is required, "none" is displayed.
A sound is heard.
It is possible to set 3 service levels:
Level Number of tightenings Service level
1 25 000 Calibration
2 250 000 Intermediate
(for heavy duty applications only)
3 500 000 Standard
Go to the main screen.
Press this button during 2 seconds.
Press this button to reach Maintenance.
Go to Tool, then Service alarm, select a level, save and validate.
Once the service is performed, reset the indicators.
Go to the "Maintenance/Service alarm" menu and press OK.

EN Service
06/2020 17 / 24
Calibration via tool display
The calibration procedure is recommended to compensate for any possible drift of the tool torque or after each
change of tool element.
This function is set in the "Maintenance" menu.
1. Enter the Maintenance password in the "Configuration" menu.
2. Insert a torque transducer in line with the tool and connect it to any measuring unit from the Desoutter range.
3. Go to "Maintenance/Calibration".
Select the number of tightenings required to execute the calibration and press OK.
Run a Pset the number of times already configured (at max. torque and with an angle above 180° (at low
speed)).
Go on with other tightenings by pressing the trigger.
4. The average torque value is displayed in white.
On the line below, enter the average torque value measured by the measuring unit (± 20 % vs the tool nominal
torque are allowed).
5. Use the left/right buttons to increase or decrease the value.
Press OK and save your data.
Calibration with eDOCK and CVIMONITOR
The calibration procedure is recommended to compensate for any possible drift of the tool torque or after any change
of tool element.
In the manual mode, the standard procedure is executed.
Measurements and values are typed manually by the operator.
The equipment required is as follows:
• Tool equipped with a torque transducer in line
• CVIMONITOR
• Delta measuring unit
Click this icon.
Click Tool calibration.
The standard procedure is as follows:
1. Select the Pset to execute.
2. Select the number of tightenings to perform (5 by default, 50 as a maximum).
According to the test bench use, the tightening may be preceeded by a loosening.
3. Click "Start calibration".
4. Start performing the first loosening / tightening operation. The operation must be successful.
5. At the end of each operation, enter the torque value on the measuring unit.
6. When all operations are performed, a new calibration value is displayed.
Checking before putting back into service
Prior to putting the equipment back into service, check that its main settings have not been modified and that the
safety devices work properly.
Advanced tool maintenance with ACCESS KEY
Launch CVIMONITOR.
To activate the screens, you need to have an ACCESS KEY USB stick with the right profile (configured with the
Desoutter CVIKEY software).
If not, contact your CVIKEY manager for support.

Service EN
18 / 24 06/2020
Motor align
Click this icon.
Click Motor align.
It is mandatory to calibrate the tools after a motor align.
It is recommended to align the motor in case of motor, transducer or PCB change.
Before starting, press the trigger and KEEP IT PRESSED DURING THE COMPLETE PROCESS. If not, the
tool could be severely damaged.
While pressing the trigger, click Start motor align.
The process will run during around 1 minute and will stop automatically.
Click "Stop motor align" to stop the process before the end.
Release the trigger.
Declaring fixed accessories
A fixed accessory mounted on a tool must be declared in this screen.
Click this icon.
Click Tool identification.
Select the type of accessory and fill in the parameters.
Click Write to tool.
It is mandatory to calibrate the tool equipped with the fixed accessory before use.
Upgrading tool firmware
Click this icon.
Click Upgrade tool firmware.
Contact your Desoutter representative to get the last firmware version.
Follow the instructions on screen.

EN Troubleshooting
06/2020 19 / 24
Troubleshooting
List of user infos related to the tools
Number Description Procedure
I004 Span failure 1- Span value from torque sensor is outside bounds.
2- Try once again to start the tool with no mechanical
constraints. If the problem occurs again, contact your
Desoutter representative for support.
I005 Offset failure 1- Offset value from torque sensor is outside bounds.
2- Try once again to start the tool with no mechanical
constraints. If the problem occurs again, contact your
Desoutter representative for support.
I026 Tool maintenance alarm n1 1- The tool tightening counter has been reached.
I027 Tool maintenance alarm n2 1- The tool tightening counter has been reached.
I038 Tool logs 1- Unexpected tool software exception.
2- Log file has been generated by the tool.
3- Contact your Desoutter representative for support.
I046 Abnormal battery current 1- Abnormal battery current consumption. Check the
Pset settings.
2- This error can be due to wrong speed settings.
I063 Battery pack removed 1- Battery pack removed from the tool detected.
2- After few seconds, the tool will shutdown
I065 External start ignored 1- External start detected but ignored.
2- Check tool and external start configuration.
I103 Invalid rotary selector direction 1- Change the direction of the rotary selector.
2- Verify that the rotary selector is in correct position
or not damaged.
I205 Torque settings 1- Invalid Torque setting: torque is greater than tool
characteristics.
2- Check Pset settings with the tool characteristics.
I206 Speed settings 1- Invalid speed setting: speed is greater than tool
characteristics.
2- Check Pset settings with the tool maximum speed.
I210 Invalid Pset selected 1- The selected Pset does not match the Pset selectable
in the Assembly Process.
I211 Invalid trigger configuration 1- The tool connected to the system is not equipped
with the trigger required by the trigger configuration.
2- Adjust your trigger configuration to the tool or
change the tool according to the trigger configuration.
I224 IGBT too hot 1- Power electronics too warm.
2- Let the system cool down.
I251 No Pset selected 1- No Pset selected.
2- Select a Pset.
I270 Time settings 1-Invalid Time setting|2-Check Pset settings with cor-
rect time value settings
W010 Tool calibration expired 1- The tool calibration date has expired.
2- A tool calibration needs to be done to ensure the
measurement accuracy.
W028 Battery tool version error 1 - Battery tool version and system version are not
compatible.
W030 The battery is low. 1- The battery is low.
2- Recharge the battery.
W033 Tool time error 1- The tool time is not set correctly. The tightening re-
sults will not be time stamped.
2- Connect the tool to the system to set date and time.

Troubleshooting EN
20 / 24 06/2020
Number Description Procedure
W036 Tool memory full 1- The tool memory is full.
2- Connect the tool to the system to empty the mem-
ory.
W062 Overload of torque 1- Overload of the torque (could be a rehit).
2- Check the tool cable is not damaged.
W212 Result not stored 1- It is not possible to store the tightening result in the
system.
2- Contact your Desoutter representative for support.
W216 Current high 1- Maximum current exceeded.
2- Contact your Desoutter representative for support.
W267 Result transfer error Result transfer error.
E007 Motor too hot 1- Tool is locked because the maximum motor temper-
ature has been reached.
2- Tool will remain locked until the motor temperature
comes back to its normal value.
E008 Tool angle fault 1- Problem detected with the tool angle sensor.
2- The tool needs maintenance.
E009 Tool invalid parameters 1- Check the tool compatiblity.
2- The tool memory cannot be read or is invalid.
3- The tool needs maintenance. If the problem occurs
again, contact your Desoutter representative for sup-
port.
E012 Tool EEPROM error 1- The tool memory cannot be read or is invalid.
2- The tool needs maintenance. If the problem occurs
again, contact your Desoutter representative for sup-
port.
E018 Torque out of range ! 1- The target torque value is above the tool maximum
torque.
2- Check Pset settings with tool characteristics.
E029 The battery is empty. 1- The battery back is discharged. The tool cannot
tighten.
2- Recharge the battery pack.
E031 Battery error 1- Abnormal battery voltage. The tool cannot tighten.
2- Recharge the battery pack. If the problem occurs
again, replace the battery pack.
E032 Tool display error 1- Board display malfunction.
2- Contact your Desoutter representative for support.
E034 Tool memory error 1- The tool memory does not work properly.
2- Contact your Desoutter representative for support.
E035 Tool memory locked 1- The tool memory is locked to protect old data from
rewriting.
2- Connect the tool to the computer via eDOCK to re-
trieve old data.
E037 Tool trigger error 1- The tool trigger does not work properly.
2- Check and clean the trigger. If the problem occurs
again, contact your Desoutter representative for sup-
port.
E045 Abnormal battery voltage 1- Check the battery pack.
2- This error can be due to charger malfunction or end
of life battery.
E047 Battery is too low. 1- Check the battery pack.
2- If the problem occurs again, replace the battery
pack.
E048 Battery type not allowed 1- Battery type not allowed.
2- Replace the battery pack or your configuration.