Seitron freetime evo User manual

Freetime Evo Radio
USER MANUAL
Daily/Weekly wireless programmable thermostat

DCD02B2001SE 040429 281122
3
INDEX
GENERAL FEATURES 5
TECHNICAL FEATURES 5
CLASSIFICATION UNDER REG. 2013.811.CE 6
SIZE 6
TURNING ON / OFF WITH ANTI-FREEZE MODE ACTIVATED 6
OPERATION LOGIC 6
REMOTE ROOM SENSOR 6
TIME / TEMPERATURE DISPLAY 6
DISPLAY BACKLIGHT 6
INSTALLATION 7
WIRELESS SYSTEM CONFIGURATION 7
WIRINGS 7
CONTROL OF A PELLET STOVE 7
INSERTING / REPLACING THE BATTERIES 8
BATTERY LEVEL 8
KEYS AND KNOB FUNCTIONS 9
DISPLAY 10
DAILY - WEEKLY PROGRAM SETTING 11
TIME - CURRENT DAY REGULATION 11
HEATING / COOLING SETTING 11
COMFORT TEMPERATURE SETTING 12
ECONOMY TEMPERATURE SETTING 12
DAILY TIME PROGRAM SETTING 13
WEEKLY TIME PROGRAM SETTING 14
TIME SCHEDULE SHARING WITH OTHER WIRELESS THERMOSTATS 15
MANUAL OPERATION MODE 19
OPEARATION MODE ON PAUSE / VACATION 20
USER PARAMETERS SETTING 22
USER PARAMETERS DETAILS 24
TROUBLESHOOTING 26

DCD02B2001SE 040429 281122
5
GENERAL FEATURES
Wall-mounted and battery powered daily/weekly wireless programmable electronic thermostat, it allows to set the room temperature easily and
precisely. Its main feature is the lack of electrical connections; in fact, on/off signals are transmitted to the receiving unit via radio, making the
installation of this device easy and inexpensive, especially where there is no existing electrical system available. Suitable for controlling heating and
cooling systems, it is equipped with a large backlit display to show all functional indications, the detected room temperature or, optionally, the current
time. The room temperature is regulated on two levels: Comfort and Reduction (in accordance with the set time schedule).
The minimum settable temperature is +0,5°C (anti-frost temperature): this allows to protect your heating system from any damage due to freezing,
if freetime evo is turned off. Featured with an input for the remote sensor connection, the device offers the possibility to regulate the Offset on the
internal sensor or on the remote sensor. This parameter enables to correct any systematic reading errors due to the placement of freetime evo or the
remote sensor, in areas which are not suitable for room temperature detection.
TECHNICAL FEATURES
Power supply: 2 x 1,5V alkaline (Type AA)
Battery life: >3 years
Frequency: 868,150 MHz
Modulation: GFSK
Max. transmitted RF power: < 1 mW
Antenna type: Internal
Max. distance from the receiver: >300 m in open eld or >50 m inside buildings (it depends on building and environment)
Regulation eld: comfort: 5°C .. 40°C
economy: 5°C .. 40°C
Type of internal sensor: NTC 10kΩ ±1% @ 25°C beta (25-85°C) 3977 ±1%
Range: -10,0°C .. +50,0°C
Precision: ±1,0°C
Resolution: 0,1°C
Type of remote sensor (optional): NTC 10kΩ ±1% @ 25°C beta (25-85°C) 3977 ±1%
Range: -10,0°C .. +60,0°C
Precision: ±1,0°C
Resolution: 0,1°C
Max. remote sensor wires length: 15 m
Differential: 0,0°C .. 5,0°C
Anti-frost: 0,5°C .. 25,0°C (Can be disabled)
Internal sensor Offset: ±10,0°C. (Default 0.0°C)
Remote sensor Offset: ±10,0°C. (Default 0.0°C)
Protection grade: IP 30
Type of action: 1
Overvoltage category: II
Pollution degree: 2
Tracking index (PTI): 175
Class of protection against
electric shock: III
Rated impulse voltage: 2500V
Number of manual cycles: 1000
Number of automatic cycles: NO LIMIT
Software class: A
EMC test voltage: 3V
EMC test current: 38mA
Distances tolerances fault
mode ‘short’ exclusion: ±0,15mm
Ball pressure test temperature: 75°C
Operating temperature: 0°C .. +40°C
Storage temperature: -10°C .. +50°C
Humidity limits: 20% .. 80% RH non condensing
Case: Material: ABS+PC V0 self-extinguishing
Color: White

DCD02B2001SE 040429 281122
6
CLASSIFICATION UNDER REG. 2013.811.CE
Class: IV
Contribution to energy efciency: 2%
SIZE
TURNING ON / OFF WITH ANTI-FREEZE MODE ACTIVATED
In order to deactivate or activate freetime evo, press the key“ “, The device will be in OFF condition and the display will show the writing “OFF”
and the symbol “ “. If the programmable thermostat in set on winter operation mode (see user parameter PAr 6.0 H_C) and the anti-freeze mode
is activated, the display shows the related symbol “ “ and the set anti-freeze setpoint temperature (see user parameter PAr 1.0 AFr); in this case
the room temperature is regulated according to the set value for the anti-freeze parameter.
OPERATION LOGIC
On “Heating” mode, when the detected room temperature, by the internal sensor or alternatively by the remote sensor, is lower than the set one
(manually or by program), freetime evo will turn on the relay to start the boiler and the symbol “ “ appears on the display.
On “Cooling mode”, when the detected room temperature, by the internal sensor or alternatively by the remote sensor, is higher than the set one
(manually or by program), freetime evo will turn on the relay to start the cooling system and the symbol “ “ appears on the display.
The switch from Heating mode to Cooling mode and vice-versa is not automatic, it has to be manually set using the user parameter “H_C” (see chapter
“USER PARAMETERS SETTINGS“).
REMOTE ROOM SENSOR
The freetime evo has an input for connecting an optional remote probe. The remote probe can be used to detect room temperature or floor temperature
or other temperature. The remote probe can be connected to sense room temperature in case the programmable thermostat needs to be installed
in a location not suitable for sensing room temperature. Alternatively, the remote probe can be congured to measure floor temperature, a useful
function in underfloor heating systems. In case the installation requires the installation of a remote probe, it is necessary to connect a probe with the
characteristics listed in the section ‘TECHNICAL FEATURES’, to terminals 4 and 5 as shown in the connection diagram in the chapter ‘CONNECTIONS’.
If in doubt about the type of probe to be connected, please consult the manufacturer. Depending on the desired function for the remote probe, the
user parameter “PAr 3.0 Entc” must be set.
TIME / TEMPERATURE DISPLAY
By pushing the knob, the current time or the detected room temperature can be alternatively displayed.
If a remote probe has been connected to detect the floor temperature and has been congured for its temperature to be shown on the display, pressing
the knob will cycle between displaying Time, Room Temperature, and Floor Temperature.
The floor temperature is indicated on the display by the symbol ‘ ’.
The temperatures detected are shown corrected by the set Offset values (see user parameters PAr 2.0 OFS1 and/or PAr 3.0 OFS2).
WARNING:
The programmable thermostat, in order to optimize battery life, detects the room temperature every 3 minutes and, accordingly, decides on the
activation or deactivation of the relay. Immediate temperature acquisition can be forced by pressing the ‘ ’ button.
DISPLAY BACKLIGHT
The display backlight is turned on if a key is pressed or when the knob is rotated.
The backlight is turned off automatically 20 seconds after a key has been pushed or the knob has been rotated or pushed.
36mm 134mm
86mm

DCD02B2001SE 040429 281122
7
INSTALLATION
WARNING
- To properly set the room temperature, install the programmable thermostat far from heat sources, airstreams or particularly cold
walls (thermal bridges).
If a remote sensor is used, the note is applied to the sensor and not to the programmable thermostat.
- In order to connect the external probe use cables with minimum section of 1,5 mm² and with a maximum length of 15 m. Do not
pass the cables through the pipes where the power lines run.
- If the load controlled by the relay of the thermostat’s receiver operates with mains voltage, the connection must be made via an
omnipolar switch complying with current standards and with a contact opening of at least 3 mm in each pole.
- Installation and electrical wirings of this appliance must be made by qualied technicians and in compliance with the current
standards.
- Before wiring the device be sure to turn the mains power off.
WIRELESS SYSTEM CONFIGURATION
When freetime evo radio is purchased in bundle with its receiver, it is already factory pre-matched with its receiver.
Before installing the programmable thermostat in the desired position, it is necessary to test whether the receiving unit correctly receives its
radio signals. This operation is performed by activating, on the freetime evo radio, the ‘Test’ mode; this function is activated by pressing the
keys ‘ ’ and ‘
24h
’ at the same time. When in ‘Test’ mode, the thermostat shows on the display the text ‘TEST’, and continuously transmits
ON and OFF commands to the receiver with a pause of 2 seconds between one and the next. Everytime a command is transmitted the symbol
‘’ flashes on the display and in the receiver the relay of the relevant output should continuously turn on and off every 2 seconds, the status is
also indicated by the relevant Led. If this happens, the thermostat communicates correctly with the receiver. When placing the thermostat in the
desired room, make sure that the two devices are still communicating properly. If the thermostat is positioned too far away from the receiver,
the relay output will always remain On or Off. In this case, it is recommended that a better position is found, possibly closer to the receiver, and
make sure the new position is not close to metal screens or reinforced concrete walls because this could weaken the radio transmission. The
signal quality can be monitored in the receiver, see the relative documentation for further information.
The ‘Test’ mode can be ended by pressing the keys ’ ’ or ‘
24h
’ or ‘ ’ . In any case the ‘Test’ mode will end automatically after approximately
17 minutes.
If the freetime evo radio is purchased individually, or you intend to install it with multi-channel receivers, you must proceed to self-learn
its address on the receiver by performing the ‘Test’ mode (described above), used in this case to self-learn the address of the programmable
thermostat on the receiver. See the instructions of the receiver module for the self-learning procedure.
WIRINGS
CONTROL OF A PELLET STOVE
The programmable thermostat can be set to control the room temperature by turning a pellet stove on and off.
The receiver should be connected to the stove according to the connection diagram in the receiver instruction manual.
In order to limit the number of stove on/offs, congure the following parameters as shown:
- HYSt PAr6.0: room temperature control hysteresis at 1.0°C
- tMIn PAr8.0: minimum relay turn-on time at 30 minutes
Remote probe input
Remote probe
cable input

DCD02B2001SE 040429 281122
8
INSERTING / REPLACING THE BATTERIES
In order to insert / replace the batteries, proceed as follows:
1. Open the plastic slider placed on the front of the product, which
gives access to the battery compartment, sliding it to the left.
2. Extract the batteries, levering with a tool if needed.
3. Insert the new batteries, respecting the polarities indicated. The
batteries must be alkaline at 1.5V type AA.
4. Check the clock accuracy and, if necessary, adjust it.
WARNING
- If the batteries need to be replaced, dispose them in the special containers for recycling.
- Replace the batteries within a few seconds in order not to lose the set time.
BATTERY LEVEL
The display always shows the battery life status with the symbol “ ”.
The battery life is full if all 3 indicators are on inside the battery symbol.
On the contrary, the batteries are low and must be replaced if the display shows the symbol “ “ (with only one bar left).
WARNING
- If the display shows the blinking writing “bAtt“ and the symbol “ “ (completely empty), it means that the battery power is too
low to allow the device to work properly and the output will always be off.
In this case freetime evo won’t regulate the temperature and the time schedule; the time and the detected room temperature won’t be
displayed.

DCD02B2001SE 040429 281122
9
KEYS AND KNOB FUNCTIONS
Double function key:
- Access the setting of the Comfort temperature (Set-Point).
- Setting the regulation in Comfort mode, when in “Time program setting”.
Double function key:
- Access the setting of the Economy temperature
(Set-Point).
- Setting the regulation in Economy mode, when in
“Time program setting”.
Double function key:
- Conrm the settings.
- Enter the clock regulation mode, when pushed for
2 sec.
Double function key:
- Short press: Enter the “Time program setting“ mode.
- Pressed for 5 s: Switches from daily mode to weekly
mode and vice versa.
Double function key:
- When operating normally, starts the “Pause” mode
(temporary stand-by).
- On “Time program setting” sets the regulation
mode on Off (OFF/Anti-frost).
Double function key:
-When operating normally, on each press it cycles
through modes: Manual 24 hours >Permanent
Manual>Automatic
- On “Time program setting” copies the time
program from the current day to the next day. *
Double function key:
- Turn on / off freetime evo.
- Exit from Edit mode, when on “hourly program” or “user parameters settings”.
Multi-functions knob:
- On normal operation:
- By pushing the knob, shows the time of the detected room temperature.
- If the backlight is off, by rotating the knob it activates the display backlight.
- On “Comfort / Economy temperature setting” (when the keys “ ” or “ ”are pressed) by rotating the knob it is possible to set the temperature
of the selected mode.
- On “Hourly Program Setting”, by rotating the knob towards right/left, shifts the hour-cursor through the 24 hours.
- By pushing the knob for 10 seconds, it enters the mode “Setting User Parameters” and then:
- Rotating the knob, the display shows all the advanced parameters of freetime evo.
- When a “User Parameter” is selected, pushing the knob it enters edit mode of the selected parameter:
- By rotating the knob, it is possible to set the desired value/data.
- By pushing the knob again the chosen setting is conrmed.
- On mode “Manual 24 hours” / “Manual Permanent” by rotating the knob it is possible to set the desired temperature (Set-Point) on “manual” mode.
* Valid only if the programmable thermostat has been set to “weekly mode”.

DCD02B2001SE 040429 281122
10
DISPLAY
Symbols
On the table below, are shown the symbols which can appear on the display and their meaning:
Time Slots
0-24 hours
The segments shows the time slot set to Economy temperature
The segments shows the time slot set to Comfort temperature
Time / room temperature indication
Set Comfort temperature
(Setpoint)
Set Economy temperature
(Setpoint)
The cursor shows the temperature
which is being set.
Indicates that the temperature displayed is the remote
sensor temperature
Battery life indicator
Operation mode
Battery life.
Comfort mode temperature setting (Set-Point).
Economy mode temperature setting (Set-Point).
Shows that the regulation temperature (Set-Point) is on edit mode.
Anti-freeze mode activated, the display also shows the writing OFF (programmable thermostat off).
Activation in heating mode (relay activated).
Activation in cooling mode (relay activated).
24h
Room temperature regulation in Manual mode until 24.00.
24h
Room temperature regulation in permanent Manual mode.
The programmable thermostat is on “User parameters setting” or freetime evo shows a fault condition.
Programmable thermostat off.
Regulation interrupted (Pause mode) for less than 96 hours; when the time is nished the programmable thermostat automatically restarts.
Regulation interrupted (Vacation mode) for more than 96 hours (4 days); when the time is nished the programmable thermostat
automatically restarts.
The temperature shown on the display is the temperature of the remote sensor connected to terminals 4 and 5 (Floor temperature).
The thermostat is transmitting a radio command.
The thermostat is in ‘Test’ mode, that is, it transmits a command every 2 seconds for self-learning the radio address on the receiver.
* Valid only if the programmable thermostat has been set in “weekly programming”.
Week-day 1 Monday .. 7 Sunday*.

DCD02B2001SE 040429 281122
11
DAILY - WEEKLY PROGRAM SETTING
The programmable thermostat is set to daily mode by factory default.
To set the daily or weekly programming mode of the programmable thermostat, perform the following operations:
1. The display of the programmable thermostat shows the normal operation mode:
WARNING!
The access to the program setting mode IS NOT allowed on the following operations modes:
Off, Pause, Holiday, Manual 24h, Permanent manual.
2. Open the flap, gaining the access to the buttons.
3. Keep the “ “ button pressed for at least 5 seconds; the programmable thermostat, depending on the initial programming mode, switches from
daily mode to weekly mode or vice versa.
If the programmable thermostat is set on weekly program mode, the display shows the weekday number, placed between the segments strip and
the clock / room temperature indicator.
Programmable thermostat set to weekly progrm mode Programmable thermostat set to daily program mode
Weekday number
WARNING!
The rst time that the programmable thermostat is set to weekly program mode, it asks to set the clock and the current day of the
week (see chapter “Time - current day regulation“).
TIME - CURRENT DAY REGULATION
In order to set the clock of the programmable thermostats, follow instructions below:
1. Open the flap which gives access to the buttons.
2. Push for at least 2 seconds the button “ “; the display shows “Set CLO” and the hour digits blink.
3. Set the hours by rotating the knob (right=Increase / left=Decrease).
4. Conrm with “ “ or by pushing the knob; the minutes digits blink.
5. Set the minutes by rotating the knob (right=Increase / left=Decrease).
6. Conrm with “ “ or by pushing the knob; the weekday is blinking.
7. Set the day of the week by turning the knob (to the right = Increase / to the left = Decrease); the selected day of the week flashes (1 Monday ..
7 Sunday).
8. Conrm with “ “ or pressing the knob.
WARNING!
- Setting the day of the week is only possible if the programmable thermostat was previously set to weekly programming.
- If the programmable thermostat has been set in daily programming, it will only be possible to adjust the hour and minutes.
HEATING / COOLING SETTING
Refer to the parameter “H_C” on the section “SETTING USER PARAMETERS”.

DCD02B2001SE 040429 281122
12
COMFORT TEMPERATURE SETTING
In order to set the Comfort temperature, follow this procedure:
1. Open the flap which gives access to the buttons.
2. Push the button “ “.
3. Rotate the knob, to adjust the regulation temperature (Set-point).
4. Conrm the set value with “ “ or pushing the knob.
ECONOMY TEMPERATURE SETTING
In order to set the Economy temperature, follow this procedure:
1. Open the flap which gives access to the buttons.
2. Push the button “ “.
3. Rotate the knob, to adjust the regulation temperature (Set-point).
4. Conrm the set value with “ “ or pushing the knob.
WARNING
Normally, in order to get a temperature decrease, the Economy
temperature must be set to a lower value than the Comfort
temperature. The arrow, placed near the
economy Set-point temperature,
blinks indicating the edit mode.
This is the room temperature value
detected by the internal / remote
sensor.
The arrow, placed near the
comfort Set-point temperature,
blinks indicating the edit mode.
This is the room temperature value
detected by the internal / remote
sensor.

DCD02B2001SE 040429 281122
13
DAILY TIME PROGRAM SETTING
During the normal operation, the upper and lower segments strip of the display show the regulation mode of freetime evo, which allows to customize
the daily time program according to each proper need.
The upper segments strip shows the temperature regulation on Comfort mode, while the lower one shows the temperature regulation on Economy.
The default time program is shown below:
TIME SCHEDULE EDITING - BRIEF DESCRIPTION
Push “ “ to enter the editing of the time program.
Turn the knob to select the time from which you want to change the time program.
Rotate the knob to select the desired time without modifying the default time program.
Push “ “ to set the comfort mode (on the time histogram bar it is shown the segment on the upper strip).
Push “ “ to set the economy mode (on the time histogram bar it is shown the segment on the lower strip).
Push “ “ to set the Off Mode (OFF/Antifrost) (NO segment is displayed on the time histogram bar).
At every push of the button “ “ or “ “ the clock moves on the next half hour.
Every segment, shown on the time histogram, represents half an hour.
Set the desired mode for the next half hours up to complete the entire day by repeatedly pressing “ “ or “ “ or “ “.
In order to conrm the changes, push the knob or wait 10 seconds without pushing any button.
In order to cancel the modications, reset to the last time schedule set and exit from “Time schedule” edit mode, push the button “ “.
Hours corresponding to
the shown segment on the
histogram
First segment blinking
It shows that the “hourly pro-
gram” mode is active
Temperature regulation mode set for the selected half hour:
“ “: Comfort mode
“ “: Economy mode
“ “: OFF/Anti-frost mode
FACTORY SETTINGS (DEFAULT)
TIME SLOT REGULATION MODE
00:00 .. 06:00 Economy
06:00 .. 09:00 Comfort
09:00 .. 16:00 Economy
16:00 .. 22:00 Comfort
22:00 .. 24:00 Economy

DCD02B2001SE 040429 281122
14
WEEKLY TIME PROGRAM SETTING
During the normal operation, the upper and lower segments strip of the display show the regulation mode of freetime evo, which allows to customize
the daily time program according to each proper need.
The upper segments strip shows the temperature regulation on Comfort mode, while the lower one shows the temperature regulation on Economy.
The default time program is shown below:
TIME SCHEDULE EDITING - BRIEF DESCRIPTION
Push “ “ to enter the editing of the time program.
The display shows the flashing number 1 (1 = Monday); if you do not want to modify this day, press the button “ “ to go to the next day.
Once the day to be set is selected, rotate the knob to select the time from which you want to change the time program.
Push “ “ to set the comfort mode (on the time histogram bar it is shown the segment on the upper strip).
Push “ “ to set the economy mode (on the time histogram bar it is shown the segment on the lower strip).
Push ““to set the Off mode (OFF/Antifrost) (NO segment is displayed on the time histogram bar).
At every push of the button “ “ or “ “ or “ “ the clock moves on the next half hour.
Every segment, shown on the time histogram, represents half an hour.
Select the required mode for the next half hours until the entire day is completed by repeatedly pushing the button “ “ or “ “ or “ “.
Once the daily program is completed, proceed as follows:
Push the button “ “ in order to copy the program of the current day on the next one. By pushing the key “ “, the programmable thermostat
automatically stores the program of the current day and proceeds to the next day program by coping the hourly schedule of the previous day.
1
FACTORY SETTINGS (DEFAULT)
MONDAY .. FRIDAY
TIME SLOT REGULATION MODE
00:00 .. 06:00 Economy
06:00 .. 09:00 Comfort
09:00 .. 16:00 Economy
16:00 .. 22:00 Comfort
22:00 .. 24:00 Economy
SATURDAY .. SUNDAY
TIME SLOT REGULATION MODE
00:00 .. 08:00 Economy
08:00 .. 23:00 Comfort
23:00 .. 24:00 Economy
Hours corresponding to
the shown segment on the
histogram
First segment blinking
It shows that the “hourly pro-
gram” mode is active
Temperature regulation mode set for the selected half hour:
“ “: Comfort mode
“ “: Economy mode
““: OFF/Antifrost mode

DCD02B2001SE 040429 281122
15
or
Push the knob or the key “ “ in order to conrm the settings made; on the contrary, press the key “ “ to reset the last stored hourly schedule
and exit from the “Time schedule” mode.
Warning: By pressing the knob or the key “ “ the time schedule settings for the current day are conrmed.
The display shows the hourly program of the next day; repeat the procedure for the following days.
Once the program is set for the whole week, push the knob or the key “ “ or “ “ or wait 40 seconds without pushing any button in order to
conrm the settings made.
Programming example Monday-Friday and Saturday-Sunday
If you want to set the same time program from Monday to Friday:
1. set the schedule for Monday, press the “ “ button 4 times in order to copy the same program on every day until Friday, save
Friday pressing the “OK” button.
2. set Saturday, press the button “ “ to copy the same program on Sunday, conrm Sunday pressing the button “ “ or “ “.
TIME SCHEDULE SHARING WITH OTHER WIRELESS THERMOSTATS
In a system made by one programmable thermostat and some more plain thermostats one in each room, it is possible to make the thermostats regulate
according to the time schedule programmed in the programmable thermostat.
This can be achieved using a multi-channel receiver and associating the outputs driven by the themostats to the output driven by the programmable
thermostat. In this way a programmable thermostat and the thermostats associated with it will form a ‘zone’. For example, in a home, it would
be possible to create the ‘living zone’ and the ‘bedroom zone’, with temperature regulation in each room according to different time schedules
programmed on two different programmable thermostats.
See the receiver’s documentation for instruction how to associate outputs. In the receiver, associated channels will receive from the programmable
thermostat the time slot information and therefore the information of which setpoint temperature, comfort or economy, to use for the regulation.
Also the off or antifreeze states are received by the associated thermostats. If the programmable thermostat is regulating a comfort temperature, the
associated thermostats will regulate according to their setpoint knob temperature, instead if the programmable thermostat is regulating an economy
temperature, the associated thermostats will regulate according to a reduction temperature which can be adjusted in the receiver.
Likewise if the device is off with 5°C antifreeze function, also the associated thermostats will regulate a 5°C antifreeze temperature.

DCD02B2001SE 040429 281122
16
PROGRAMMING EXAMPLE:
1.
During normal operation, push “ “ to enter the
time schedule edit mode.
2.
The display shows:
- “SEt PrG” to indicate the access to the edit mode of the
time schedule.
-Number 1 is blinking and it corresponds to Monday.
Valid only if the programmable thermostat has been
congured in “weekly programming”.
- Hour 0:00.
- The blinking segment corresponds to hour 0:00.
- The symbol “ “ to indicate the regulation mode
which has been set.
The time schedule is set starting from hour 0:00 towards
24:00, with steps of 30 minutes.
3.
By pressing the knob or the key “ “ the selection
of the day of the week is moved WITHOUT modifying
the previously set time program.
Valid only if the programmable thermostat has been
congured in “weekly programming”.
4.
The time cursor is moved by turning the knob, without
modifying the previously set time schedule.
The corresponding segment will blink at the selected half
hour.
3
12345 76
12345 76
12345 76

DCD02B2001SE 040429 281122
17
5. After selecting the time from which you intend to modify the time schedule (in this case, from 5:00), proceed as follows:
Push “ “ to set the comfort mode (on the time
histogram, a segment is shown on the upper strip).
WARNING
- In order to set the economy mode push “ “.
- To set the “Pause” mode (temporary stand-by) press
“ “.
- At every push of the button “ “ or “ “ or
“ “ the time cursor automatically shifts on the
next half hour.
6.
Push again “ “ to set the comfort mode (on the
time histogram, a segment is shown on the upper strip).
7.
Continue with the setting as shown in this example
(points 4 and 5), until the entire daily time slot is done.
On the opposite case, go to the next step.
Otherwise, or at the end of the programming of the entire
daily strip, go to the points:
9If the programmable thermostat has been set on
“Daily programming mode” .
8If the programmable thermostat has been set on
“Weekly programming mode” and it is required to set
the time schedule by copying the time schedule set
for the selected day.
8a If the programmable thermostat has been set on
“Weekly programming mode” and it is required to set
the time schedule manually.
8
When the setting for the current day is over,press
the button “ “ in order to copy the program of the
current day onto the next.
If the “ “ key is pressed, it automatically stores
the current day program and it goes directly to the next
day program by copying the time schedule of the previous
day.
There is one exception related to day 7 of the week
(Sunday) and this exception is that the pressure of the
“ “ button, exits from the programming phase storing
the settings made.
Valid only if the programmable thermostat has been
congured in “weekly programming”.
12345 76
12345 76
12345 76
12345 76

DCD02B2001SE 040429 281122
18
8a.
In order to store the set time schedule and go to the
time schedule of the next day, press the knob or the
“ “ button.
Valid only if the programmable thermostat has been
congured in “weekly programming”.
8b.
Keep going with the setting of the time schedule as
shown in this example (points 3 and 8), up to nish
the entire week.
Valid only if the programmable thermostat has been
congured in “weekly programming”.
9.
In order to store the set time schedule and exit from
the mode “Time Schedule” push the knob or the button
“ “ or wait 10 seconds without pushing any button.
In order to cancel the modications done, thus
restoring the last time program set up, and to exit the
“Hourly Schedule” mode, push the button “ “.
10.
WARNING
- If it is needed to restore the default time schedule, it is necessary to access the user parameter PAR 9.0 “dFLt” (set default data); in
this case all the user parameters will be restored to factory values.
- The access to the time program setting IS NOT allowed on the following operational conditions: Off, Pause, Holiday, Manual 24h,
Manual permanent
- When on time schedule setting, by pressing the knob or the button “ “ or by waiting 40 seconds without pressing any button, all
the changes made are stored.
12345 76
12345 76
12345 76
3

DCD02B2001SE 040429 281122
19
MANUAL OPERATION MODE
With the button “ “, freetime evo can be forced to regulate the room temperature independently from the time program.
On manual operation mode the temperature regulation (Set-Point) can be modied at any time by turning the knob and it is independent from the Comfort
and Economy temperature of the time program.
By repeatedly pressing the button “ “, you can alterne between Automatic (normal operation) and Manual 24 hours, from Manual 24 hours to
Manual Permanent, and from Manual Permanent it goes back to Automatic.
During manual operation mode the display will not show the time schedule, instead it will only show the room temperature, the relay status (possible
symbols “ “ or “ “ are lit), the symbol “
24h
“ (manual 24h) or “ “ (manual permanent) and the “Manual“ Set-Point temperature.
1.
By pressing only once the button “ “ Manual 24 hours mode is
activated.
2.
The display shows the symbol “
24h
“ (manual 24h); freetime evo
remains on manual until 23:59 of the current day, after which it returns
to Automatic mode.
Note: If Manual 24h mode is active and the Vacation mode is activated,
when the Vacation setting expires and if it is past the 23.59, the
programmable thermostat will go back to Automatic operation following
the set time schedule.
By pushing a second time the button “ “ the operation is forced
on Manual Permanent.
3.
The display shows the symbol “ “ (manual permanent); freetime
evo regulates the temperature on manual mode until the button “ “ is
pushed again.
During manual operation (“
24h
“ or “ “) by turning the knob it is
possible to set the desired “manual” Set-point temperature, inside the
range 5.0 .. 40°C.
4.
Pressing the button once again “ “ freetime evo goes back to
automatic operation mode (normal operation according to the set time
schedule).

DCD02B2001SE 040429 281122
20
OPEARATION MODE ON PAUSE / VACATION
By pressing the button “ “, freetime evo stops the room temperature regulation taking itself on “Pause“ or “Vacation“ mode depending on the
time set rotating the knob:
Pause: time set less than 96 hours
Vacation: time set more than 4 days (96 hours)
This mode activates (by pushing the knob) a countdown time. When the countdown expires, freetime evo is reset to the previously set operation mode.
1.
2.
NOTE:
- Turn the knob to set the Pause (h) hours or the Vacation (d) days:
- From 1 to 95 hours the display shows the symbol “ “ to indicate the “Pause“ mode.
- From 4 to 99 days the display shows the symbol “ “ to indicate the “Vacation” mode.
- The symbols blink indicating that the countdown is still to be conrmed.
Hours indication (h).
Number of hours.
Pause mode indicator.
Days indication (d).
Number of days.
Vacation mode indicator.