DFI SU968 User manual

www.d.comChapter 1 Introduction
1
SU968
COM Express Compact Module
User’s Manual
A41300702

www.d.comChapter 1 Introduction
2
Copyright
This publication contains information that is protected by copyright. No part of it may be re-
produced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifi-
cally disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this docu-
ment. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
© 2017. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
COM Express Specification Reference
PICMG®COM Express ModuleTM Base Specification.
http://www.picmg.org/
FCC and DOC Statement on Class B
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-
able protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for compli-
ance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.

www.d.comChapter 1 Introduction
3
Chapter 1 - Introduction............................6
Specifications...........................................................................6
Features .................................................................................7
Chapter 2 - Concept..................................8
COM Express Module Standards................................................8
Specification Comparison Table.................................................9
Chapter 3 - Hardware Installation............ 10
Board Layout......................................................................... 10
Block Diagram .......................................................................10
Mechanical Diagram............................................................... 11
System Memory..................................................................... 12
Connectors ............................................................................13
CPU Fan Connector................................................................... 13
COM Express Connectors .......................................................... 13
COM Express Connectors .......................................................... 14
COM Express Connectors Signals and Descriptions ....................... 15
Standby Power LED ...............................................................22
Cooling Option.......................................................................22
Installing SU968 onto a Carrier Board..................................... 23
Installing the COM Express Debug Card.................................. 25
Chapter 4 - BIOS Setup .......................... 27
Overview ..............................................................................27
Insyde BIOS Setup Utility....................................................... 28
Main ....................................................................................... 28
Advanced ............................................................................... 28
Security .................................................................................. 35
Boot ....................................................................................... 36
Exit ........................................................................................ 38
Updating the BIOS.................................................................39
Notice: BIOS SPI ROM ...........................................................39
Chapter 5 - Supported Software .............. 41
Chapter 6 - RAID ................................... 55
Chapter 7 - Intel AMT Settings ............... 59
Appendix A - Troubleshooting .................. 72
Table of Contents
Appendix B - Insyde BIOS Standard Status POST Code
........................................................................74

www.d.comChapter 1 Introduction
4
About this Manual
An electronic file of this manual is included in the DVD. To view the user’s manual in the DVD,
insert the DVD into a DVD-ROM drive. The autorun screen (Main Board Utility DVD) will ap-
pear. Click “User’s Manual” on the main menu.
Warranty
1. Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2. The warranty is void if the product has been subjected to physical abuse, improper instal-
lation, modification, accidents or unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-
stances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequencial damages to the
product that has been modified or altered.
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in han-
dling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con-
nectors by their ends.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servic-
ing. After installation or servicing, cover the system chassis before plugging the power
cord.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other com-
ponents. Perform the upgrade instruction procedures described at an ESD worksta-
tion only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chas-
sis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.

www.d.comChapter 1 Introduction
5
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• One SU968 board
• One DVD
• One Heat Sink (Height: 23.8mm)
Optional Items
• COM332-B Carrier Board Kit
• Heat spreader (Height: 11mm)
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance with the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Before Using the System Board
Before using the system board, prepare basic system components.
If you are installing the system board in a new system, you will need at least the following
internal components.
• Storage devices such as hard disk drive, CD-ROM, etc.
You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.

www.d.comChapter 1 Introduction
6
WatchDog
Timer
Output &
Interval
System Reset, Programmable via Software from 1 to 255 Seconds
Security TPM Available Upon Request
Power Type 12V, 5VSB, VCC_RTC (ATX mode)
12V, VCC_RTC (AT mode)
Consumption Typical: I7-6600U: 12V @ 0.86A (10.28Watt)
Max.: I7-6600U: 12V @ 1.372A (16.46Watt)
OS Support Windows 7 (/WES7) 32/64-bit
Windows 8.1 (64-bit)
Windows 10 IoT Enterprise 64-bit
Debian 8 (with VESA graphic driver)
CentOS 7 (with VESA graphic driver)
Ubuntu 15.10 (Intel graphic driver available)
Environment Temperature Operating
: 0 to 60°C
: -45 to 80°C -40 to 85°C (with heat spreader)
Storage: -40 to 85°C
Humidity Operating: 5 to 90% RH
Storage: 5 to 90% RH
MTBF 921,923 hrs @ 25°C; 460,715 hrs @ 45°C; 256,677 hrs @ 60°C
Calculation Model: Telcordia Issue 2, Method Case 3
Environment: GB, GC – Ground Benign, Controlled
Mechanical Dimensions COM Express®Compact
95mm (3.74") x 95mm (3.74")
Compliance PICMG COM Express®R2.1, Type 6
Chapter 1 - Introduction
Specifications
Chapter 1
System Processor 6th Generation Intel®CoreTM Processors, BGA 1356
Intel®CoreTM i7-6600U Processor, Dual Core, 4M Cache, 2.6GHz (3.4GHz), 15W
Intel®CoreTM i5-6300U Processor, Dual Core, 3M Cache, 2.4GHz (3.0GHz), 15W
Intel®CoreTM i3-6100U Processor, Dual Core, 3M Cache, 2.3GHz, 15W
Intel®Celeron®Processor 3955U, Dual Core, 2M Cache, 2.0GHz, 15W
Memory Two 204-pin SODIMM up to 16GB
Dual Channel DDR3L 1600MHz
BIOS Insyde SPI 128Mbit
Graphics Controller Intel®HD Graphics GT Series
Feature OpenGL 5.0, DirectX 12, OpenCL 2.1
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/H265, VP8, VP9
HW Encode: AVC/H.264, MPEG2, JPEG, HEVC/H265, VP8, VP9
Display 1 x VGA/DDI (DDI available upon request)
1 x LVDS/eDP (eDP available upon request)
1 x DDI
VGA: resolution up to 2560x1600 @ 60Hz
LVDS: dual channel 24-bit, resolution up to 1920x1200 @ 60Hz
HDMI: resolution up to 4096x2160 @ 24Hz or 2560x1600 @ 60Hz
DP++: resolution up to 4096x2304 @ 60Hz
Triple Displays VGA + LVDS + DDI
DDI + eDP + DDI
Expansion Interface 5 PCIe x1 or 4 PCIe x1 + 1 PCIe x4 or 3 PCIe x1 + 2 PCIe x2
1 x LPC
1 x I2C
1 x SMBus
2 x UART (TX/RX)
Audio Interface HD Audio
Ethernet Controller 1 x Intel®I219LM with iAMT11.0 PCIe (10/100/1000Mbps)
(only Core i7/i5 supports iAMT)
I/O USB 4 x USB 3.0
8 x USB 2.0
SATA 3 x SATA 3.0 (up to 6Gb/s) (Core i7/i5)
2 x SATA 3.0 (up to 6Gb/s) (Celeron)
RAID 0/1/5/10 (Core i7/i5 )
DIO 1 x 8-bit DIO

www.d.comChapter 1 Introduction
7
Chapter 1
Features
• Watchdog Timer
The Watchdog Timer function allows your application to regularly “clear” the system at the set
time interval. If the system hangs or fails to function, it will reset at the set time interval so
that your system will continue to operate.
• DDR3L
DDR3L SDRAM provides backward compatibility to DDR3 memory modules but can operate at
the same or at a lower power level.
• Graphics
The integrated Intel®HD graphics engine delivers an excellent blend of graphics performance
and features to meet business needs. It provides excellent video and 3D graphics with out-
standing graphics responsiveness. These enhancements deliver the performance and compat-
ibility needed for today’s and tomorrow’s business applications. It supports VGA/DDI, LVDS/
eDP and DDI interfaces for 3 display outputs.
• Serial ATA
Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of
up to 6Gb/s (SATA 3.0), it improves hard drive performance to be faster than the standard
parallel ATA, which only has data transfer rate of 100MB/s. The bandwidth of the SATA 3.0 will
be limited by carrier board design.
• Gigabit LAN
The Intel®I219LM with iAMT11.0 Gigabit LAN controller supports up to 1Gbps data transmis-
sion (only Core i7/i5 supports iAMT).
• USB
The system board supports the new USB 3.0. It is capable of running at a maximum transmis-
sion speed of up to 5 Gbit/s (625 MB/s) and is faster than USB 2.0 (480 Mbit/s, or 60 MB/s)
and USB 1.1 (12Mb/s). USB 3.0 reduces the time required for data transmission, reduces
power consumption, and is backward compatible with USB 2.0. It is a marked improvement
in device transfer speeds between your computer and a wide range of simultaneously
accessible external Plug and Play peripherals.

www.d.comChapter 2 Concept
8
Chapter 2
Chapter 2 - Concept
106.00
91.00
70.00
51.00
4.00
18.00
6.00
0.00
16.50 4.00 0.00
Extended
BasicCompact
Mini
74.20 80.00 91.00 121.00 151.00
Common for all Form Factors
Extended only
Basic only
Compact only
Compact and Basic only
Mini only
COM Express Module Standards
The figure below shows the dimensions of the different types of COM Express modules.
SU968 is a COM Express Compact module. The dimension is 95mm x 95mm.

www.d.comChapter 2 Concept
9
Chapter 2
Specification Comparison Table
Module Pin-out - Required and Optional Features C-D Connector. PICMG®COM.0 Revision 2.1
The table below shows the COM Express standard specifications and the corresponding specifications supported on the SU968 module.
• 5 Indicates 12V-tolerant features on former VCC_12V signals.
• 6 Cells in the connected columns spanning rows provide a rough approximation of features
sharing connector pins.
Connector Feature
COM Express Module Base
Specification Type 6
(No IDE or PCI, add DDI+ USB3)
Min / Max
DFI SU968
Type 6
A-B
A-B PCI Express Lanes 0 - 5 1 / 6 6
A-B LVDS Channel A 0 / 1 1
A-B LVDS Channel B 0 / 1 1
A-B eDP on LVDS CH A pins 0 / 1 1
A-B VGA Port 0 / 1 0/1 (Option : DDI2 or VGA)
A-B TV-Out NA NA
A-B DDI 0 NA NA
A-B5Serial Ports 1 - 2 0 / 2 2
A-B CAN interface on SER1 0 / 1 0
A-B SATA / SAS Ports 1 / 4 3 (with Intel® Celeron®: 2)
A-B AC’97 / HDA Digital Interface 0 / 1 1
A-B USB 2.0 Ports 4 / 8 8
A-B USB Client 0 / 1 0
A-B USB 3.0 Ports NA NA
A-B LAN Port 0 1 / 1 1
A-B Express Card Support 1 / 2 2
A-B LPC Bus 1 / 1 1
A-B SPI 1 / 2 1
A-B
SDIO (muxed on GPIO) 0 / 1 0
General Purpose I/O 8 / 8 8
A-B SMBus 1 / 1 1
A-B I2C 1 / 1 1
A-B Watchdog Timer 0 / 1 1
A-B Speaker Out 1 / 1 1
A-B External BIOS ROM Support 0 / 2 1
A-B Reset Functions 1 / 1 1
A-B6
System I/O
System Management
Connector Feature
COM Express Module Base
Specification Type 6
(No IDE or PCI, add DDI+ USB3)
Min
/
Max
DFI SU968
Type 6
A-B
A-B Thermal Protection 0 / 1 1
A-B Battery Low Alarm 0 / 1 1
A-B Suspend/Wake Signals 0 / 3 1
A-B Power Button Support 1 / 1 1
A-B Power Good 1 / 1 1
A-B VCC_5V_SBY Contacts 4 / 4 4
A-B5Sleep Input 0 / 1 1
A-B5Lid Input 0 / 1 1
A-B5Fan Control Signals 0 / 2 2
A-B Trusted Platform Modules 0 / 1 1
A-B
A-B VCC_12V Contacts 12 / 12 12
Power
Power Management
Connector Feature
COM Express Module Base
Specification Type 6
(No IDE or PCI, add DDI+ USB3)
Min / Max
DFI SU968
Type 6
C-D
PCI Express Lanes 16 - 31 0 / 16 0
PCI Express Graphics (PEG) 0 / 1 0
Muxed SDVO Channels 1 - 2 NA NA
PCI Express Lanes 6 - 15 0 / 2 2
PCI Bus - 32 Bit NA NA
PATA Port NA NA
LAN Ports 1 - 2 NA NA
DDIs 1 - 3 0 / 3 1/2 (Option : DDI2 or VGA)
USB 3.0 Ports 0 / 4 4
C-D
C-D VCC_12V Contacts 12 / 12
12
System I/O
Power
C-D6
C-D6

www.d.comChapter 3 Hardware Installation
10
Chapter 3
Chapter 3 - Hardware Installation
Board Layout
Top View
Bottom View
Block Diagram
EEPROM
SATA 3.0 3x
USB 3.0 4x
A / B
SMBus
6th Generation
Intel®Core™i7/i5/i3
Intel®GLAN
I219LM
MDI
SPI Flash
SPI Bus
C / D
DDR3L 1600MHz
SODIMM
Channel A
PCIe x1
PCIe x1 (4 x1/2 x2/1 x4)
LPC Bus
8-bit DIO
WDT
I2C Bus
TPM
1.2/2.0
(optional)
Serial Port 0,1
Fan PWM/
TACH_IN
SLP/LID
TCA6408A
Embedded
Controller
IT8528E
DDI Port 1
HDA
USB 2.0 8x
eDP/DDI
(optional)
PTN3460
LVDS
(optional)
DDI
(optional)
CH7517
VGA
DDI Port 2
PCIe x1 (2 x1/1 x2)
PCIe x1 (2 x1)
DDR3L 1600MHz
SODIMM
Channel B
CPU Fan
1
SPI Flash BIOS
Standby
Power LED
Intel
I219LM
Intel
BGA 1356
DDR3L_1 SODIMM
iTE
IT8528VG
PWMIC
NXP
PTN3460
Chrontel
CH7517
TPM (optional)
COM Express connector
C1
D1
C110
D110
B1
B110
A1
A110
COM Express connector
DDR3L_2 SODIMM