DFI KS070-BT User manual

1
KS070-BT Installation Guide
Package Contents
• One 7" Touch Panel PC
• One sheet of Poron foam
• One HDD drive bay kit
• 1 DVD disk includes:
-Manual
DFI reserves the right to change the specifications at any time prior to
the product's release. For the latest revision and more details of the
installation procedure, please refer to the user's manual on the website.
www.dfi.com

2
Panel
Top View
HDMI
USB 3.0 Antenna
hole
COM 2
(RS232/RS422/RS485)
COM 4/ 8-bit DIO
Antenna
hole
Reset
Power button
(Green LED)
COM 1
(RS232/RS422/RS485)
Status LED (Blue)
Antenna
hole
Line-out
Bottom View
COM 3
(RS232/RS422/RS485)
USB 2.0
LAN 2
DC-in
Mic-in LAN 1

3
Removing the Chassis Cover
1. Make sure the system and all other peripheral devices connected to it
have been powered-off.
2. Disconnect all power cords and cables.
3. The 8 mounting screws on the rear side of the system are used to
secure the cover to the chassis. Remove these screws and put them in a
safe place for later use.
4. Lift the cover up to open the system.
5. The Mini PCIe and the micro SD slots are readily accessible after
removing the chassis cover.
Mounting screw
Mounting screw

4
Installing a SATA Drive
2. Align the mounting holes of the SATA HDD with the mounting holes on
the HDD drive bay and use the provided mounting screws to attach the
SATA HDD to the drive bay.
1. The SATA data and power connectors are on the system board.
SATA mounting location
SATA connectors
Mounting screw
Mounting screw

5
3. Connect one end of the SATA cable to the SATA power and data
connectors on the SATA drive and the other end of the SATA cable to
the SATA power and data connectors on the system board.
4. Align the mounting holes of the HDD drive bay with the mounting holes
on the system and use the provided mounting screws to secure the
drive bay in place.
SATA power/data cable
SATA drive
Mounting screw
SATA drive
SATA connectors

6
Installing a Mini PCIe Card
Note:
The system also has one additional full-size Mini PCIe and one half-size Mini PCIe slot
that uses PCIe and LPC interface respectively.
The system board is equipped with 3 Mini PCIe slots: two full-size and one
half-size slots. Here we will demonstrate the installation of a full-size Mini
PCIe card (mSATA interface) for capacity expansion.
1. Grasp the Mini PCIe card by its edges and align the notch in the
connector of the PCIe card with the notch in the connector on the
system board.
2. Push the Mini PCIe card down and use the provided mounting screws to
secure the card on the system board.
Mounting screw

7
The wall mount kit includes the following:
• 2 wall mount brackets
• Bracket screws
2. Select a place on the wall where you will mount the Panel PC.
3. Use the provided mounting screws to attach “wall mount bracket 1” to
the wall.
Mounting Options
Wall mount
Wall mount bracket 1 Wall mount bracket 2
Wall mount bracket 1
Mounting screw
1. Before starting any installation procedures, attach the poron foam to
the Panel PC.
Poron foam

8
4. Attach the other bracket (wall mount bracket 2) to the rear of the
Panel PC.
Wall mount bracket 2
Mounting screw
Hooks
Screw
5. Slide the Panel PC to "wall mount bracket 1" to attach the two brackets
with the hooks. Then tighten the screw to secure the assembly in place.

9
Panel mount
The panel mounting kit includes the following:
• 6 mounting clamps
2. Select a place on the panel (or wall) where you will mount the Panel PC.
3. Cut out a shape on the panel that corresponds to the Panel PC’s rear
dimensions (202.5mm x 140.3mm) and ensure that the Panel PC can be
fitted into the panel properly.
4. Insert the Panel PC from the outside surface of the panel into the
mounting hole until it is properly fitted against the panel.
5. Position the mounting clamps along the rear edges of the Panel PC and
insert them into the slits around the Panel PC.
1. Before starting any installation procedures, attach the poron foam to
the Panel PC.
Poron foam
Panel
Mounting hole
202.5
140.3

10
6. The first and second clamps must be positioned and secured diagonally
prior to mounting the rest of the clamps. Tighten the clamp’s screw
using an electric screwdriver by pressing the white plastic cap onto
the back of the panel. The illustration below shows that all clamps are
properly mounted.
White plastic cap
fi
Slit for mounting the clamp
Mounting clamp
Note:
The maximum thickness of your panel’s mounting wall should be 10 mm for secure
panel mount.