DFI KS101-BT User manual

www.dfi.com
1
DFI reserves the right to change the specifications at any time prior to the product's release. This QIG may
be based on editions that do not resemble your actual products. For the latest revision and more details of
the installation procedure, please refer to go.dfi.com/KS101-BT or scan the QR code on the right.
Quick Installation Guide
KS101-BT
• KS101-BT Touch Panel PC
• One sheet of poron foam
• One HDD drive bay kit
Package Contents
Top View
HDMI
USB 3.0
Antenna
hole
COM 2
(RS232/RS422/RS485)
COM 4/ 8-bit DIO
Antenna
hole
Reset/
Status LED
Power button
COM 1
(RS232/RS422/RS485)
Bottom View
Line-out
COM 3
(RS232/RS422/RS485)
USB 2.0
LAN 2
DC-in
COM 5
(RS232)
Mic-in
LAN 1

2Quick Installation Guide |
Removing the Chassis Cover
Make sure the system and all other peripheral devices connected to it have been powered-off.
1. Disconnect all power cords and cables.
2. The 8 mounting screws on the rear side of the system are used to secure the cover to the
chassis. Remove these screws and put them in a safe place for later use.
Mounting screw
Mounting screw
Mounting screw
Installing a SATA Drive
The system can accommodate one 2.5" SATA drive.
1. Align the mounting holes of the SATA HDD with the mounting holes on the HDD drive bay
and use the provided mounting screws to attach the SATA HDD to the drive bay.
Mounting screw
2. Connect the SATA cable. Align the mounting holes of the HDD drive bay with the mounting holes
on the system and use the provided mounting screws to secure the drive bay in place.
SATA drive
SATA power/data cable
Mounting screw

3Quick Installation Guide |
Installing a Mini PCIe Card
Note:
The system also has one additional full-size Mini PCIe and one half-size Mini PCIe slot that
use the mSATA and LPC interface respectively.
The system board is equipped with 3 Mini PCIe slots: two full-size and one half-size slots. Here we will
demonstrate the installation of a full-size Mini PCIe card (working in conjunction with a SIM card) for
4G connectivity.
1. Grasp the Mini PCIe card by its edges and align the notch in the connector of the PCIe card with
the notch in the connector on the system board.
2. Push the Mini PCIe card down and use the provided mounting screws to secure the card on the
system board.
Mounting screw

4
Quick Installation Guide |
Board Layout and Jumper Settings
933-KS1010-000G
A46001944
LAN 1 LAN 2
3
DDR3L
DDR3L
DDR3L
DDR3L
Mini PCIe with SIM
COM 4
RS232/RS422/RS485
1210
31
JP22 1
1 1
(JP20) (JP18) (JP17)
(JP21)
1 3
1210
COM 2
RS232/RS422/RS485
COM 1
RS232/RS422/RS485
USB 0
USB 3.0
HDMI
Reset
Power
3940
21
LVDS LCD Panel
USB 7 USB 6
Mic-in
1
Battery
Buzzer
1
Chassis Intrusion
1
Clear CMOS Data (JP24)
SPI Flash BIOS
eMMC
(optional)
iTE
IT8528E
Mini PCIe with LPC mSATA
MicroSD (optional)
1
System Fan
1
USB 0 Power Select (JP5)
1
2
5 6
(JP23)
1 1 1
(JP3) (JP4)
1 2 10
9
COM 6
1
10
9
COM 5
1 1
USB 2 Power Select (JP6)
USB 5-7 Power
Select (JP7)
1 2 10
9
USB 5
(JP25)
USB 2.0
USB 2.0
(JP17) (JP20)
COM 4/DIO Select (JP22, JP21)
Digital I/O 0-3 Output State Digital I/O Power Select
Panel Power Select
(JP3) (JP4) (JP23)
Backlight Enable Power Select Auto Power-on Select (JP25) Dimming Mode Select
(JP18)
Digital I/O 4-7 Output State
1
COM 3
RS232/RS422/RS485
4
1(JP2)
(JP2)LCD/Inverter Power Select
SATA 1
4 1 SATA
Power
1
SATA 2.0
I C
Line-out
DC-in
USB 2
USB 2 USB 2
USB 2
USB Power Select: 0 (JP5), 1-2 (JP6), 5-7 (JP7)
+5V_standby (default) 1-2 On
+5V 2-3 On
Clear CMOS Data JP24
Normal (default) 1-2 On
Clear CMOS Data 2-3 On
Panel Power Select JP23
+12V 1-2 On
+5V 3-4 On
+3.3V (default) 5-6 On
Auto Power-on Select JP25
Power-on via power button (default) 1-2 On
Power-on via AC power 2-3 On
Note:
You cannot use COM 4 and DIO at the same time.
Please set up JP21 and JP22 together.
Backlight Enable Power Select JP3
+3.3V (default) 1-2 On
+5V 2-3 On
Dimming Mode Select JP4
Voltage Mode 1-2 On
PWM Mode (default) 2-3 On
Digital I/O Output State JP18 (DIO 4-7)
JP20 (DIO 0-3)
GND (default) 1-2 On
+5V or +5V_standby 2-3 On
Digital I/O Power Select JP17
+5V_standby 1-2 On
+5V (default) 2-3 On
COM 4/DIO Select JP21, JP22
COM 4 (default) 1-2, 4-5
7-8, 10-11 On
DIO 2-3, 5-6
8-9, 11-12 On
LCD/Inverter Power Select JP2
+12V (default) 1-2 On
+5V 2-3 On