DFI KS156P-EHL User manual

© September 08, 2023 DFI Inc.
www.dfi.com
Quick Installation Guide
Package Contents
1 x Touch Panel PC
1 Quick Installation Guide
KS156P-EHL & KS215P-EHL
15.6" & 21.5" Industrial Touch Panel PC

Quick Installation Guide | KS156P-EHL & KS215P-EHL 1
Product Overview
I/O Views
1
2
3
4
DC-In
DP++
HDMI
2.5G LAN
7
2
1
3
6
45
8
9
7
5
6
7
8
9
USB 3.2 Gen1
Line-Out
COM Ports 1~4
Power Button
USB 3.2 Gen2

Removing the Chassis Cover
Please observe the following guidelines and follow the instructions to open the system.
1. Make sure the system and all other peripheral devices connected to it have been
powered off.
2. Disconnect all power cords and cables.
Step 1:
The 8 screws of the system are used to secure the cover to the chassis. Remove the screws
and put them in a safe place for later use.
Step 2:
Lift the cover to open the system.
Quick Installation Guide | KS156P-EHL & KS215P-EHL 2

Mounting Options
Wall mount bracket 1 Wall mount bracket 2
Screw
Wall Mount
Step 1:
Select a place on the wall where you will mount the Panel PC.
Step 2:
Use the provided mounting screws to attach wall mount bracket 1 onto the wall.
Step 3:
Attach the other bracket (wall mount bracket 2) to the rear of the Panel PC.
Step 4:
Slide the Panel PC to wall mount bracket 1 and attach the two brackets together with the
hooks. Then tighten the screw to secure the assembly in place.
Quick Installation Guide | KS156P-EHL & KS215P-EHL 3

Panel Mount - KS156P-EHL
Step 1:
Select a place on the panel (or wall) where you will mount the Panel PC.
Step 2:
Cut out a shape on the panel that corresponds to the Panel PC’s rear dimensions (359mm x
194mm) and ensure that the Panel PC can be fitted into the panel properly.
The flat panel thickness is less than 3mm. Be sure to route or trim down the thick wall to 3 mm
or slightly less for the clamps to recess and be compatible with your wall or enclosure.
Step 3:
Insert the Panel PC from the outside surface of the panel into the mounting hole until it is
properly fitted against the panel.
Step 4:
Position the mounting clamps along the rear edges of the Panel PC and insert them into the
slits around the Panel PC.
Step 5:
The first and second clamps must be positioned and secured diagonally prior to mounting the
rest of the clamps. Tighten the clamp’s screw using an electric screwdriver by pressing the
white plastic cap onto the back of the panel. The illustration below shows that all clamps are
properly mounted.
Quick Installation Guide | KS156P-EHL & KS215P-EHL 4

Panel Mount - KS215P-EHL
Step 1:
Select a place on the panel (or wall) where you will mount the Panel PC.
Step 2:
Cut out a shape on the panel that corresponds to the Panel PC’s rear dimensions (359mm x
194mm) and ensure that the Panel PC can be fitted into the panel properly.
The flat panel thickness is less than 3mm. Be sure to route or trim down the thick wall to 3 mm
or slightly less for the clamps to recess and be compatible with your wall or enclosure.
Step 3:
Insert the Panel PC from the outside surface of the panel into the mounting hole until it is
properly fitted against the panel.
Step 4:
Position the mounting clamps along the rear edges of the Panel PC and insert them into the
slits around the Panel PC.
Step 5:
The first and second clamps must be positioned and secured diagonally prior to mounting the
rest of the clamps. Tighten the clamp’s screw using an electric screwdriver by pressing the
white plastic cap onto the back of the panel. The illustration below shows that all clamps are
properly mounted.
Quick Installation Guide | KS156P-EHL & KS215P-EHL 5

Installing an Antenna
Quick Installation Guide | KS156P-EHL & KS215P-EHL 6
Before installing the antenna, please make sure that the following safety cautions are
wellattended.
1. Make sure the PC and all other peripheral devices connected to it has been
powered down.
2. Disconnect all power cords and cables.
Step 1:
There are antenna holes reserved on the right side of the system and by default covered by
rubber plugs. Please remove the plug prior to installing an antenna.
Step 2:
Connect the internal cable to the board's antenna connector, screw the antenna connector
through the antenna hole with washers and nuts, and screw on the antenna as illustrated
below.
Antenna ConnectorCableModule Connector NutWasher
Chassis Wall Antenna
DFI reserves the right to change the specifications at any
time prior to the product's release. This QR may be based
on the product’s revision. For more documentation and
drivers, please visit the download page at www.dfi.com/
downloadcenter, or via the QR codes to the right.