DFI KS070-ALE39P User manual

1
KS070-AL Installation Guide
Package Contents
• One 7" Touch Panel PC
• One sheet of Poron foam
• 1 DVD disk includes:
- Manual
DFI reserves the right to change the specications at any time prior to
the product's release. For the latest revision and more details of the
installation procedure, please refer to the user's manual on the website.
www.d.com

2
Panel
Top View
Mic-in
USB 2.0
Line-out
LAN 2 LAN 1
DP++
Power on/off
USB 3.0
VGA
DC-in
Bottom View
COM 1
(RS232/RS422/RS485)
Antenna Hole
COM 2
(RS232/RS422/RS485)

3
The CFast card slot can be accessed externally without opening the chassis.
Before installing a CFast card, take off the CFast card slot cover.
Installing a CFast Card
CFast slot cover
1. Gently insert the CFast card straight with the label on the CFast card
facing up until you feel it lock into place. Do not force the card into the
slot if the card is not correctly inserted.
2. Close the CFast card cover and attach the screw. To eject the card, push
the card inward to release the lock and pull it out.
CFast slot cover

4
Removing the Chassis Cover
1. Make sure the system and all other peripheral devices connected to it
have been powered-off.
2. Disconnect all power cords and cables.
3. The 12 mounting screws on the top and bottom as well as both sides of
the system are used to secure the cover to the chassis. Remove these
screws and put them in a safe place for later use.
4. Lift the cover up to open the system.
5. The Mini PCIe and the M.2 sockets are readily accessible after removing
the chassis cover.
Mounting screw
M.2 socket Mini PCIe socket
Mounting screw
Mounting screw

5
Installing an M.2 Card
The system is equipped with one M.2 socket, supporting the M.2 22x42mm
(key B) form factor. Use the following procedure to install an M.2 card:
M.2 card
1. Align the notch at the edge of the M.2 card with the key in the connector.
2. Insert the M.2 card into the connector.
Mounting screw
Note:
The M.2 socket supports PCIe, USB, and SATA signals and can accommodate common
mobile broadband and storage modules. For jumper settings on switching the signal
betwen SATA and PCIe, refer to "Board Layout and Jumper Settings."
3. Push down on the other end of the M.2 card and secure and card on the
mainboard with the provided mounting screw.

6
Installing a Mini PCIe Card
The system board is equipped with one Mini PCIe slot that supports PCIe
and USB signals. Use the following procedure to install a Mini PCIe card:
1. Grasp the Mini PCIe card by its edges and align the notch in the
connector of the PCIe card with the key in the connector on the
system board.
2. Push the Mini PCIe card down and use the provided mounting screws to
secure the card on the system board.
Mini PCIe card
Mounting screw

7
The VESA mount kit includes the following:
• 2 VESA mount brackets
• Bracket screws
2. Select a place on the wall where you will mount the Panel PC.
3. Use the provided mounting screws to attach “VESA mount bracket 1” to
the wall.
Mounting Options
VESA mount
VESA mount bracket 1 VESA mount bracket 2
VESA mount bracket 1
Mounting screw
1. Before starting any installation procedures, attach the poron foam to
the Panel PC.
Poron foam

8
4. Attach the other bracket (VESA mount bracket 2) to the rear of
the Panel PC.
5. Slide the Panel PC to "VESA mount bracket 1" to attach the two brackets
with the hooks. Then tighten the screw to secure the assembly in place.
VESA mount bracket 2
Mounting screw
Hooks
Screw

9
2. Select a place on the panel (or wall) where you will mount the Panel PC.
3. Cut out a shape on the panel that corresponds to the Panel PC’s rear
dimensions (210.5mm x 132.2mm) and ensure that the Panel PC can be
tted into the panel properly.
4. Insert the Panel PC from the outside surface of the panel into the
mounting hole until it is properly tted against the panel.
5. Position the mounting clamps along the rear edges of the Panel PC and
insert them into the slits around the Panel PC.
Panel
Mounting hole
132.20
210.50
5
Panel mount
The panel mounting kit includes the following:
• 6 mounting clamps
1. Before starting any installation procedures, attach the poron foam to
the Panel PC.
Poron foam

10
Note:
The at panel thickness is less than 5mm.
132.20
210.50
5
Slit for mounting the clamp
Mounting clamp
White plastic cap
6. The rst and second clamps must be positioned and secured diagonally
prior to mounting the rest of the clamps. Tighten the clamp’s screw
using an electric screwdriver by pressing the white plastic cap onto
the back of the panel. The illustration below shows that all clamps are
properly mounted.