DFI TPC121 User manual

www.dfi.com
1
Chapter 1 Introduction
TPC121/150/170/190-SB
Touch Panel PC
User’s Manual
A24640503

www.dfi.com
2
Chapter 1 Introduction
Copyright
This publication contains information that is protected by copyright. No part of it may be re-
produced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifi-
cally disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this docu-
ment. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
© 2015. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
FCC and DOC Statement on Class A
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-
able protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for compli-
ance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.

www.dfi.com
3
Chapter 1 Introduction
Table of Contents
Copyright.............................................................................................................2
Trademarks........................................................................................................2
FCC and DOC Statement on Class A.....................................................2
About this Manual..........................................................................................4
Warranty..............................................................................................................4
Static Electricity Precautions......................................................................4
Safety Measures..............................................................................................4
About the Package.........................................................................................5
Chapter 1 - Introduction.............................................................................6
Overview.........................................................................................................6
Key Features..................................................................................................7
Specifications ................................................................................................8
Getting to Know the TPC121/150/170/190-SB.................................12
Mechanical Dimensions............................................................................14
Chapter 2 - Getting Started..................................................................... 17
Preparing the System...............................................................................17
Installing Devices.......................................................................................17
Configuring the BIOS................................................................................ 17
Installing the Operating System............................................................17
Installing the Drivers................................................................................17
Chapter 3 - Installing Devices................................................................18
Removing the Chassis Cover..................................................................18
Installing an SODIMM...............................................................................19
Installing a SATA Drive.............................................................................20
Installing a Mini PCIe Card.....................................................................22
Latch .........................................................................................................22
Removing the Latch....................................................................................23
Installing the Mini PCIe Card.......................................................................24
Installing the PCI and PCIe x1 Expansion Cards..............................24
Connecting Cables to Terminal Blocks.................................................25
Chapter 4 - Jumper Settings...................................................................26
Clear CMOS..................................................................................................26
PS/2 Power Select.....................................................................................26
USB Power Select......................................................................................27
Power-on Select .........................................................................................27
COM 1 RS232/422/485 Select................................................................28
COM 1 Signal Select .................................................................................28
Front Audio or Audio Amplifier Select..................................................29
Chapter 5 - Ports and Connectors........................................................30
Front Panel I/O Port..................................................................................30
USB Ports...................................................................................................30
Bottom Panel I/O Ports............................................................................31
PS/2 Mouse and PS/2 Keyboard Ports..........................................................31
RJ45 LAN Ports...........................................................................................32
USB Ports...................................................................................................32
Graphics Interfaces.....................................................................................33
COM (Serial) Ports...................................................................................... 34
Audio.........................................................................................................34
I/O Connectors........................................................................................... 35
SATA (Serial ATA) Connectors .....................................................................35
Digital I/O Connector and Digital I/O Power Connector.................................36
Audio Amplifier Connector........................................................................... 36
Chassis Intrusion Connector........................................................................37
Cooling Fan Connectors...............................................................................37
Standby Power LED....................................................................................38
Power Connectors.......................................................................................38
Expansion Slots..........................................................................................39
Front Panel Connector ................................................................................39
Battery....................................................................................................... 40
SDVO Connector.........................................................................................40
SDVO-LVDS Daughterboard (optional)..........................................................41
Installing the SDVO-LVDS Daughterboard onto the Motherboard (optional)....43
Chapter 6 - Mounting Options................................................................45
Wall Mount...................................................................................................45
Panel Mount ................................................................................................46
Chapter 7 - BIOS Setup............................................................................48
Overview.......................................................................................................48
AMI BIOS Setup Utility.............................................................................49
Updating the BIOS....................................................................................60
Notice: BIOS SPI ROM.............................................................................61
Chapter 8 - Supported Software...........................................................62
Chapter 9 - Audio Configuration........................................................... 75
Appendix A - Smart Fan Setting Guide.............................................. 77
Appendix B - Watchdog Sample Code................................................79
Appendix C - System Error Message...................................................80
Appendix D - Troubleshooting Checklist............................................ 81

www.dfi.com
4
Chapter 1 Introduction
About this Manual
An electronic file of this manual is included in the CD. To view the user’s manual in the CD, in-
sert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear. Click
“User’s Manual” on the main menu.
Warranty
1. Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2. The warranty is void if the product has been subjected to physical abuse, improper instal-
lation, modification, accidents or unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-
stances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequencial damages to the
product that has been modified or altered.
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in han-
dling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con
nectors by their ends.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servic-
ing. After installation or servicing, cover the system chassis before plugging the power cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other com-
ponents. Perform the upgrade instruction procedures described at an ESD worksta-
tion only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chas-
sis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.

www.dfi.com
5
Chapter 1 Introduction
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• 1 12”/15”/17”/19” Touch Panel PC
• 1 120W Power adapter
• 1 CD disk includes
- Manual
- Drivers
• 1 Quick Installation Guide
Optional Items
• Wall Mount kit
• Panel Mount kit
• Power Cord
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Before Using the System
Before powering-on the system, prepare the basic system components.
If you are installing the system board in a new system, you will need at least the following
internal components.
• Memory module
• Storage devices such as hard disk drive, CD-ROM, etc.
You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.
Safety Precautions
• Use the correct DC input voltage range.
• Unplug the power cord before removing the system chassis cover for installation or servic-
ing. After installation or servicing, cover the system chassis before plugging the power cord.
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
• Keep this system away from humidity.
• Place the system on a stable surface. Dropping it or letting it fall may cause damage.
• The openings on the system are for air ventilation to protect the system from overheating.
DO NOT COVER THE OPENINGS.
• Place the power cord in such a way that it will not be stepped on. Do not place anything on
top of the power cord. Use a power cord that has been approved for use with the system
and that it matches the voltage and current marked on the system’s electrical range label.
• If the system will not be used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
• If one of the following occurs, consult a service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated the system.
- The system has been exposed to moisture.
- The system is not working properly.
- The system dropped or is damaged.
- The system has obvious signs of breakage.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground the
unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does
not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.

www.dfi.com
6
Chapter 1 Introduction
Chapter 1 - Introduction
Chapter 1
Overview
TPC121 TPC150/TPC170/TPC190-SB

www.dfi.com
7
Chapter 1 Introduction
Key Features
TPC121/150/170/190-SB
Processor 3rd/2nd Generation Intel®CoreTM processors
Chipset Intel®H61 Express Chipset
LAN 2 LAN ports
COM 2 COM ports
Dual Displays HDMI and DVI-I
USB 2 Type A USB 2.0/1.1 ports at the front panel
4 Type A USB 2.0/1.1 ports at the bottom
Audio Mic-in, Line-in, Line-out
2 3W speakers (left and right sides)
Chapter 1

www.dfi.com
8
Chapter 1 Introduction
I/O Ports
• Front
-
2 Type A USB 2.0/1.1 ports
- 5 function keys: power, volume, and brightness
- 3 LED indicators: Power, HDD, Alarm
- 1 built-in antenna
• Bottom
- 1 DB-9 RS232/422/485 COM
- 1 DB-9 RS232 COM
- 1 PS/2 keyboard
- 1 PS/2 mouse
-
4 Type A USB 2.0/1.1
-
3 audio jacks: Mic-in, Line-in, Line-out
- 2 RJ45 LAN with LEDs
- 1 DVI-I
- 1 HDMI
- 1 power switch
- 1 +19V DC-in jack or 16-30V 3-pole terminal block
Expansion • 1 PCIe x1 and 1 PCI (X100-3PE2)
• 2 PCI (X100-2P1M)
• 2 Mini PCIe
- Supports PCIe and USB signals for Wi-Fi module
- Supports half/full size Mini PCIe card
Front Panel
Protection •
IP65 (Dust Tight; Water Proof protection)
Construction
• Aluminum front bezel
• Rear panel: sheet metal
Mounting
• VESA mount: 75x75 and 100x100
• Wall mount bracket* (optional)
• Panel mount: mounting clamp* (optional)
Dimensions
• 345mm x 265mm x 103mm (W x H x D)
Weight •
6.5 kg
OS Support
• Windows XP, WES 2009, POSReady 2009, Windows 7, WES 7
• Linux (Distribution available upon request)
Certification
• CE
• FCC Class A
• RoHS
Specifications
TPC121
Processor System • Processors:
- 3rd generation Intel®CoreTM processors
- 2nd generation Intel®CoreTM processors
- Supports up to 65W TDP
• Intel®H61 Express chipset
Memory • Two DDR3 1333/1600MHz SODIMM sockets (3rd generation processors)
Two DDR3 1066/1333MHz SODIMM sockets (2nd generation processors)
• Supports up to 16GB system memory
LCD and
Touch Screen • 12.1” 1024x768 TFT LCD panel with touch screen
• Supports 5-wire Resistive Touch
• 30,000 MTBF LED backlight
• Brightness (cd/m²): 500
Graphics • Intel®HD Graphics
• Display ports: HDMI and DVI-I
• HDMI and DVI-I display resolution up to 1920x1200
Storage • 1 2.5" SATA drive bay
- SATA 2.0 port with data transfer rate up to 3Gb/s
• 1 optical drive bay* (optional)
Ethernet • 1 Intel®W82579LM Gigabit Ethernet Controller
• 1 Intel®W82574L Gigabit Ethernet Controller
Audio • Realtek ALC886 5.1-channel High Definition Audio
• Two 3W speakers (left and right sides)
COM • 1 RS232/422/485 COM port
• 1 RS232 COM port
USB • 2 Type A USB 2.0/1.1 ports at the front panel
• 4 Type A USB 2.0/1.1 ports at the bottom
Power • Power input voltage
- Standard: 19~24V DC-in jack
- Option: 24V DC-in 3-pole terminal block
Cooling System • Smart fan system control suitable for quiet environments
Environment • Temperature
- Operating: -10oC ~ 50oC
- Storage: -20oC ~ 60oC
• Relative Humidity
- 90% RH at 50oC, 1 week
• Corrosion
- 4 periods of 7 days at 50oC with 90-95% relative humidity after 2 hours salt
spray or waiver
Vibration • Operating: 1G, 5~500Hz
• Non-operating: 1.5G, 5~25Hz
• IEC 68-2-64 compliant
Shock • Operating: 3G peak acceleration (11 msec. duration)
• Non-operating: 10G peak acceleration (11 msec. duration)
• IEC 68-2-27 compliant
Chapter 1
Note:
*Optional and is not supported in standard model. Please contact your sales represen-
tative for more information.

www.dfi.com
9
Chapter 1 Introduction
Chapter 1
Specifications
TPC150
I/O Ports
• Front
-
2 Type A USB 2.0/1.1 ports
- 5 function keys: power, volume, and brightness
- 3 LED indicators: Power, HDD, Alarm
- 1 built-in antenna
• Bottom
- 1 DB-9 RS232/422/485 COM
- 1 DB-9 RS232 COM
- 1 PS/2 keyboard
- 1 PS/2 mouse
-
4 Type A USB 2.0/1.1
-
3 audio jacks: Mic-in, Line-in, Line-out
- 2 RJ45 LAN with LEDs
- 1 DVI-I
- 1 HDMI
- 1 power switch
Expansion • 1 PCIe x1 and 1 PCI (X100-3PE2)
• 2 PCI (X100-2P1M)
• 2 Mini PCIe
- Supports PCIe and USB signals for Wi-Fi module
- Supports half/full size Mini PCIe card
Front Panel
Protection •
IP65 (Dust Tight; Water Proof protection)
Construction
• Aluminum front bezel
• Rear panel: sheet metal
Mounting
• VESA mount: 75x75 and 100x100
• Wall mount bracket* (optional)
• Panel mount: mounting clamp* (optional)
Dimensions
• 410mm x 320mm x 106mm (W x H x D)
Weight •
7.8 kg
OS Support
• Windows XP, WES 2009, POSReady 2009, Windows 7, WES 7
• Linux (Distribution available upon request)
Certification
• CE
• FCC Class A
• RoHS
• UL
Processor System • Processors:
- 3rd generation Intel®CoreTM processors
- 2nd generation Intel®CoreTM processors
- Supports up to 65W TDP
• Intel®H61 Express chipset
Memory • Two DDR3 1333/1600MHz SODIMM sockets (3rd generation processors)
Two DDR3 1066/1333MHz SODIMM sockets (2nd generation processors)
• Supports up to 16GB system memory
LCD and
Touch Screen • 15” 1024x768 TFT LCD panel with touch screen
• Supports 5-wire Resistive Touch
• 50,000 MTBF LED backlight
• Brightness (cd/m²): 250
Graphics • Intel®HD Graphics
• Display ports: HDMI and DVI-I
• HDMI and DVI-I display resolution up to 1920x1200
Storage • 2 2.5" SATA drive bays
- SATA 2.0 port with data transfer rate up to 3Gb/s
• 1 optical drive bay* (optional)
Ethernet • 1 Intel W82579LM Gigabit Ethernet Controller
• 1 Intel W82574L Gigabit Ethernet Controller
Audio • Realtek ALC886 5.1-channel High Definition Audio
• Two 3W speakers (left and right sides)
COM • 1 RS232/422/485 COM port
• 1 RS232 COM port
USB • 2 Type A USB 2.0/1.1 ports at the front panel
• 4 Type A USB 2.0/1.1 ports at the bottom
Power • Power input voltage
- Standard: ATX power type, AC 100-240V, 3.5A, 250W
- Option: 24V DC-in 3-pole terminal block
- Available upon request: 12V and 30V DC-in 3-pole terminal block
Cooling System • Smart fan system control suitable for quiet environments
Environment • Temperature
- Operating: -10oC ~ 50oC
- Storage: -20oC ~ 60oC
• Relative Humidity
- 90% RH at 50oC, 1 week
• Corrosion
- 4 periods of 7 days at 50oC with 90-95% relative humidity after 2 hours salt
spray or waiver
Vibration • Operating: 1G, 5~500Hz
• Non-operating: 1.5G, 5~25Hz
• IEC 68-2-64 compliant
Shock • Operating: 3G peak acceleration (11 msec. duration)
• Non-operating: 10G peak acceleration (11 msec. duration)
• IEC 68-2-27 compliant
Note:
*Optional and is not supported in standard model. Please contact your sales represen-
tative for more information.

www.dfi.com
10
Chapter 1 Introduction
Chapter 1
Specifications
TPC170
I/O Ports
• Front
-
2 Type A USB 2.0/1.1 ports
- 5 function keys: power, volume, and brightness
- 3 LED indicators: Power, HDD, Alarm
- 1 built-in antenna
• Bottom
- 1 DB-9 RS232/422/485 COM
- 1 DB-9 RS232 COM
- 1 PS/2 keyboard
- 1 PS/2 mouse
-
4 Type A USB 2.0/1.1
-
3 audio jacks: Mic-in, Line-in, Line-out
- 2 RJ45 LAN with LEDs
- 1 DVI-I
- 1 HDMI
- 1 power switch
Expansion • 1 PCIe x1 and 1 PCI (X100-3PE2)
• 2 PCI (X100-2P1M)
• 2 Mini PCIe
- Supports PCIe and USB signals for Wi-Fi module
- Supports half/full size Mini PCIe card
Front Panel
Protection •
IP65 (Dust Tight; Water Proof protection)
Construction
• Aluminum front bezel
• Rear panel: sheet metal
Mounting
• VESA mount: 75x75 and 100x100
• Wall mount bracket* (optional)
• Panel mount: mounting clamp* (optional)
Dimensions
• 443mm x 363mm x 106mm (W x H x D)
Weight •
9.6 kg
OS Support
• Windows XP, WES 2009, POSReady 2009, Windows 7, WES 7
• Linux (Distribution available upon request)
Certification
• CE
• FCC Class A
• RoHS
Processor System • Processors:
- 3rd generation Intel®CoreTM processors
- 2nd generation Intel®CoreTM processors
- Supports up to 65W TDP
• Intel®H61 Express chipset
Memory • Two DDR3 1333/1600MHz SODIMM sockets (3rd generation processors)
Two DDR3 1066/1333MHz SODIMM sockets (2nd generation processors)
• Supports up to 16GB system memory
LCD and
Touch Screen • 17” 1280x1024 TFT LCD panel with touch screen
• Supports 5-wire Resistive Touch
• 50,000 MTBF LED backlight
• Brightness (cd/m²): 380
Graphics • Intel®HD Graphics
• Display ports: HDMI and DVI-I
• HDMI and DVI-I display resolution up to 1920x1200
Storage • 2 2.5" SATA drive bays
- SATA 2.0 port with data transfer rate up to 3Gb/s
• 1 optical drive bay* (optional)
Ethernet • 1 Intel W82579LM Gigabit Ethernet Controller
• 1 Intel W82574L Gigabit Ethernet Controller
Audio • Realtek ALC886 5.1-channel High Definition Audio
• Two 3W speakers (left and right sides)
COM • 1 RS232/422/485 COM port
• 1 RS232 COM port
USB • 2 Type A USB 2.0/1.1 ports at the front panel
• 4 Type A USB 2.0/1.1 ports at the bottom
Power • Power input voltage
- Standard: ATX power type, AC 100-240V, 3.5A, 250W
- Option: 24V DC-in 3-pole terminal block
- Available upon request: 12V and 30V DC-in 3-pole terminal block
Cooling System • Smart fan system control suitable for quiet environments
Environment • Temperature
- Operating: -10oC ~ 50oC
- Storage: -20oC ~ 60oC
• Relative Humidity
- 90% RH at 50oC, 1 week
• Corrosion
- 4 periods of 7 days at 50oC with 90-95% relative humidity after 2 hours salt
spray or waiver
Vibration • Operating: 1G, 5~500Hz
• Non-operating: 1.5G, 5~25Hz
• IEC 68-2-64 compliant
Shock • Operating: 3G peak acceleration (11 msec. duration)
• Non-operating: 10G peak acceleration (11 msec. duration)
• IEC 68-2-27 compliant
Note:
*Optional and is not supported in standard model. Please contact your sales represen-
tative for more information.

www.dfi.com
11
Chapter 1 Introduction
Chapter 1
I/O Ports
• Front
-
2 Type A USB 2.0/1.1 ports
- 5 function keys: power, volume, and brightness
- 3 LED indicators: Power, HDD, Alarm
- 1 built-in antenna
• Bottom
- 1 DB-9 RS232/422/485 COM
- 1 DB-9 RS232 COM
- 1 PS/2 keyboard
- 1 PS/2 mouse
-
4 Type A USB 2.0/1.1
-
3 audio jacks: Mic-in, Line-in, Line-out
- 2 RJ45 LAN with LEDs
- 1 DVI-I
- 1 HDMI
- 1 power switch
Expansion • 1 PCIe x1 and 1 PCI (X100-3PE2)
• 2 PCI (X100-2P1M)
• 2 Mini PCIe
- Supports PCIe and USB signals for Wi-Fi module
- Supports half/full size Mini PCIe card
Front Panel
Protection •
IP65 (Dust Tight; Water Proof protection)
Construction
• Aluminum front bezel
• Rear panel: sheet metal
Mounting
• VESA mount: 75x75 and 100x100
• Wall mount bracket* (optional)
• Panel mount: mounting clamp* (optional)
Dimensions
• 472mm x 391mm x 116mm (W x H x D)
Weight •
10.2 kg
OS Support
• Windows XP, WES 2009, POSReady 2009, Windows 7, WES 7
• Linux (Distribution available upon request)
Certification
• CE
• FCC Class A
• RoHS
Specifications
TPC190-SB
Processor System • Processors:
- 3rd generation Intel®CoreTM processors
- 2nd generation Intel®CoreTM processors
- Supports up to 65W TDP
• Intel®H61 Express chipset
Memory • Two DDR3 1333/1600MHz SODIMM sockets (3rd generation processors)
Two DDR3 1066/1333MHz SODIMM sockets (2nd generation processors)
• Supports up to 16GB system memory
LCD and
Touch Screen • 19” 1280x1024 TFT LCD panel with touch screen
• Supports 5-wire Resistive Touch
• 50,000 MTBF LED backlight
• Brightness (cd/m²): 350
Graphics • Intel®HD Graphics
• Display ports: HDMI and DVI-I
• HDMI and DVI-I display resolution up to 1920x1200
Storage • 2 2.5" SATA drive bays
- SATA 2.0 port with data transfer rate up to 3Gb/s
• 1 optical drive bay* (optional)
Ethernet • 1 Intel W82579LM Gigabit Ethernet Controller
• 1 Intel W82574L Gigabit Ethernet Controller
Audio • Realtek ALC886 5.1-channel High Definition Audio
• Two 3W speakers (left and right sides)
COM • 1 RS232/422/485 COM port
• 1 RS232 COM port
USB • 2 Type A USB 2.0/1.1 ports at the front panel
• 4 Type A USB 2.0/1.1 ports at the bottom
Power • Power input voltage
- Standard: ATX power type, AC 100-240V, 3.5A, 250W
- Option: 24V DC-in 3-pole terminal block
- Available upon request: 12V and 30V DC-in 3-pole terminal block
Cooling System • Smart fan system control suitable for quiet environments
Environment • Temperature
- Operating: -10oC ~ 50oC
- Storage: -20oC ~ 60oC
• Relative Humidity
- 90% RH at 50oC, 1 week
• Corrosion
- 4 periods of 7 days at 50oC with 90-95% relative humidity after 2 hours salt
spray or waiver
Vibration • Operating: 1G, 5~500Hz
• Non-operating: 1.5G, 5~25Hz
• IEC 68-2-64 compliant
Shock • Operating: 3G peak acceleration (11 msec. duration)
• Non-operating: 10G peak acceleration (11 msec. duration)
• IEC 68-2-27 compliant
Note:
*Optional and is not supported in standard model. Please contact your sales represen-
tative for more information.

www.dfi.com
12
Chapter 1 Introduction
Getting to Know the TPC121/150/170/190-SB
Chapter 1
Front View
USB Ports
Used to connect USB 2.0/1.1 devices.
Function Keys
Used to navigate.
Alarm LED
Indicates the status when the CPU is over temperature.
HDD LED
Indicates the status of the hard drive.
Power LED
Indicates the power status of the system.
Bottom View - TPC121
Power Switch
Press to power-on or power-off the system.
HDMI Port
Use to connect an HDMI device.
DVI-I Port
Used to connect a DVI device.
COM Ports
Used to connect serial devices.
USB Ports
Used to connect USB 2.0/1.1 devices.
LAN Ports
Used to connect the system to a local area network.
Line-out
Used to connect to a speaker.
Line-in
Used to connect any audio devices such as Hi-fi set, CD player, tape player, AM/FM radio tuner,
synthesizer, etc.
Mic-in
Used to connect an external microphone.
PS/2 KB/Mouse
Used to connect a PS/2 keyboard and a PS/2 mouse.
DC-in jack
Used to plug a power adapter.
USB
Function Keys
Alarm LED
HDD LED
Power LED
Line-in
Mic-in
Line-out
COM 2
COM 1
PS/2 KB
PS/2 Mouse
USB 2.0
19~24V DC-in
(standard)
Power Switch
LANDVI-I
HDMI
24V DC-in (option)
Built-in antenna Expansion slots

www.dfi.com
13
Chapter 1 Introduction
Power Switch
Press to power-on or power-off the system.
HDMI Port
Use to connect an HDMI device.
DVI-I Port
Used to connect a DVI device.
COM Ports
Used to connect serial devices.
USB Ports
Used to connect USB 2.0/1.1 devices.
LAN Ports
Used to connect the system to a local area network.
Line-out
Used to connect to a speaker.
Line-in
Used to connect any audio devices such as Hi-fi set, CD player, tape player, AM/FM radio tuner,
synthesizer, etc.
Mic-in
Used to connect an external microphone.
PS/2 KB/Mouse
Used to connect a PS/2 keyboard and a PS/2 mouse.
DC-in jack
Used to plug a power adapter.
Bottom View - TPC150/TPC170/TPC190-SB
Power Switch
Press to power-on or power-off the system.
HDMI Port
Use to connect an HDMI device.
DVI-I Port
Used to connect a DVI device.
COM Ports
Used to connect serial devices.
USB Ports
Used to connect USB 2.0/1.1 devices.
LAN Ports
Used to connect the system to a local area network.
Line-out
Used to connect to a speaker.
Line-in
Used to connect any audio devices such as Hi-fi set, CD player, tape player, AM/FM radio tuner,
synthesizer, etc.
Mic-in
Used to connect an external microphone.
PS/2 KB/Mouse
Used to connect a PS/2 keyboard and a PS/2 mouse.
Line-in
Mic-in
Line-out
COM 2
COM 1
PS/2 KB
PS/2 Mouse
USB 2.0
Power Switch
LANDVI-I
HDMI
AC power
Expansion slots
Line-in
Mic-in
Line-out
COM 2
COM 1
PS/2 KB
PS/2 Mouse
USB 2.0
Power Switch
LANDVI-I
HDMI
24V DC-in
Expansion slots

www.dfi.com
14
Chapter 1 Introduction
Mechanical Dimensions
TPC121 TPC150
Chapter 1
345.00
248.50
186.50
265.00
6.00
103.00
34.00
Bottom View
Right ViewLeft View
Top View
Front View
130.00
130.00
250.00
90.00
270.00
75.00
100.00
75.00
100.00
90.00
270.00
Rear View
306.00
410.00
305 00
6.00 37.00
106.00
230.00
320.00
Right ViewLeft View
Top View
Front View
110.00
330.00
75.00
100.00
75.00
100.00
110.00
330.00
180.00
305.00
180.00
Rear View

www.dfi.com
15
Chapter 1 Introduction
TPC170
Chapter 1
6.00 37.00106.00
363.00
272.80
339.50
443.78
Right ViewLeft View
Top View
Front View
285.75
348.00
95.25
95.25
144.00
364.00
75.00
100.00
75.00
100.00
144.00
364.00
285.75
Rear View
TPC190-SB
472.00
377.50 116.00
47.00
6.00
300.80
391.00
Right ViewLeft View
Top View
Front View
Rear View
100.00
75.00
100.00
75.00

www.dfi.com
16
Chapter 1 Introduction
Motherboard Dimension
0.00
0.00
6.17 18.23 42.88 79.42
109.25 132.41 151.79 157.48 163.83
10.16
46.94
49.47
68.97
86.97
104.97
124.47
141.39
153.34
154.94
159.84
0.00
18.71
16.62 19.53 80.55 91.63
157.48
154.9
4
64.59
22.8
6
113.35

www.dfi.com
17
Chapter 2 Getting Started
Chapter 2
Preparing the System
Before you start using the system, you need the following items:
• SATA hard drive
• AC power adapter
• PS/2 or USB keyboard
• PS/2 or USB mouse
• CD-ROM drive (for installing software/drivers)
• Screwdriver
• Memory module (optional)
Installing Devices
The following are devices that can be installed in the TPC121/150/170 system.
• Memory module
• SATA hard drive
• Mini PCIe card
Configuring the BIOS
To get you started, you may need to change configurations such as the date, time and the
type of hard disk drive.
1. Power-on the system.
2. After the memory test, the message “Press DEL to run setup” will appear on the screen.
Press the Delete key to enter the AMI BIOS setup utility.
Installing the Operating System
Most operating system software are provided in a CD therefore you need to install a CD-ROM
drive in order to use the CD.
Make sure a 2.5” SATA drive is already installed.
1. Refer to the following chapters for information on connecting a CD-ROM drive and install-
ing a SATA drive.
2. Refer to your operating system manual for instructions on installing the operating system.
Installing the Drivers
The system package includes a CD disk. The CD includes drivers that must be installed to pro-
vide the best system performance. Refer to the Supported Software chapter for instructions on
installing the drivers.
Chapter 2 - Getting Started

Chapter 3
Chapter 3
www.dfi.com
18
Chapter 3 Installing Devices
Chapter 3 - Installing Devices
1. Make sure the system and all other peripheral devices connected to it has been powered-
off.
2. Disconnect all power cords and cables.
3. The 8 mounting screws on the rear side of the system are used to secure the cover to the
chassis. Remove these screws and then put them in a safe place for later use.
Removing the Chassis Cover
Mounting Screw
4. After removing the mounting screws, lift the cover up.
5. The memory socket, expansion slots, Mini PCIe slot and SATA drive bay are readily acces-
sible after removing the chassis cover.
Lift the Cover Upward
SODIMM socket
SATA drive bay
Mini PCIe Slot
TPC121/TPC190-SB
TPC150/TPC170
SODIMM socket
Mini PCIe slot
SATA drive bay

Chapter 3
Chapter 3
www.dfi.com
19
Chapter 3 Installing Devices
4. Grasping the module by its edges, position the module above the socket with the notch in the
socket aligned with the key on the module. Apply firm even pressure to each end of the module
until it slips down into the socket. The contact fingers on the edge of the module will almost
completely disappear inside the socket.
SODIMM
3. Note the key on the socket. The key ensures the module can be plugged into the socket in only
one direction.
SODIMM socket
1. Locate the DIMM socket on the system board.
Installing an SODIMM
2. Push the ejector tabs which are at the ends of the socket at the side.
Ejector tab
Ejector tab
5. Push the module down until the clips at each end of the socket lock into position. You will hear
a distinctive “click”, indicating the module is correctly locked into position.
Clip Clip

Chapter 3
Chapter 3
www.dfi.com
20
Chapter 3 Installing Devices
2. Remove the mounting screws that secure the HDD bracket to the drive bay.
Installing a SATA Drive
1. Locate the SATA drive bay in the chassis.
SATA drive bay
TPC150/TPC170
SATA drive bay
Mounting Screw
TPC150/TPC170
Mounting Screw
TPC121/TPC190-SB
TPC121/TPC190-SB