Dhollandia DH-P2 User manual

Order ref: MD034.EN Doc: USE_DH-P series_CE_EN_2020 Rev: 0 Date: OCT 17, 2020
Manufacturer:
DHOLLANDIA N.V. Zoomstraat 9 9160 LOKEREN (Belgium)
Tel : [phone] Fax : [phone]
e-mail : i[email protected]
website : www.dhollandia.com
DH-P2 / PH2
DH-P1 / PH1
OPERATION MANUAL
Read the manual in its entirety before operating the lift
Keep this manual in the vehicle cab, as reference for the driver and lift operator
edition

1
DHOLLANDIA
TABLE OF CONTENTS
1Understanding safety and warning signs ...................................................................................................................................2
2Contact information and disclaimers..........................................................................................................................................3
3General introduction...................................................................................................................................................................4
4Intended use ..............................................................................................................................................................................4
5Identification...............................................................................................................................................................................5
6Description and terminology ......................................................................................................................................................6
6.1 General .............................................................................................................................................................................6
6.2 Safety devices.................................................................................................................................................................12
7Safety instructions for using the lift ..........................................................................................................................................15
7.1 DO NOT use the lift without adequate safety and operator training................................................................................15
7.2 General safety instructions..............................................................................................................................................15
7.3 Danger zones, risk of crush and shear injury..................................................................................................................19
7.4 Additional instructions for the wheelchair occupants and standees ................................................................................22
7.5 Load diagram ..................................................................................................................................................................24
7.6 Recommended daily pre-trip inspection..........................................................................................................................25
7.7 Importance of preventative maintenance ........................................................................................................................26
8Operating instructions –principles and procedures .................................................................................................................27
8.1 Control units....................................................................................................................................................................27
8.1.1 Standard 2-button wander lead with spiral cable (ref. OAE001) .................................................................................27
8.1.2 Optional 3-button wander lead with spiral cable (ref. OWE002) .................................................................................27
8.1.3 Optional 4-button wander lead with spiral cable (option OWE003).............................................................................28
8.1.4 Auxiliary toggle switch control for DH-PH2* / DH-P2 lifts (option OWE001)...............................................................28
8.2 Switching the main power on/off .....................................................................................................................................29
8.3 Platform locks..................................................................................................................................................................30
8.4 Operation instructions for DH-PH2* / P2* lifts .................................................................................................................31
8.5 Operation instructions for the DH-PH1* / P1* lifts ...........................................................................................................35
9Emergency operation...............................................................................................................................................................39
10 Decals......................................................................................................................................................................................41
10.1 Introduction .....................................................................................................................................................................41
10.2 Regular decals on the lift.................................................................................................................................................41
10.3 Decals on inside of bus near the lift ................................................................................................................................43
11 Meaning of safety and warning signs.......................................................................................................................................45
12 End note...................................................................................................................................................................................47

2
DHOLLANDIA
1UNDERSTANDING SAFETYAND WARNING SIGNS
Many safety signs and symbols used in this manual are based on international standards, others refer to specific situations or
actions.
Consult section 11 on page 45 for an overview of signs and symbols used in DHOLLANDIA manuals and their meaning.
Please take special notice of the following signs used in the manual. They indicate the likelihood and severity of a potential
injury if a person fails to follow the instructions presented on the safety sign.
WARNING
Failure to understand and to follow the instructions in this manual can put the operator and any bystanders at great risk of
serious bodily injury and death.
Prior to operating the lift, make sure you understand the safety and warning signs used, and read them in conjunction with the
instructions in this manual.
If in doubt, DO NOT operate the lift. Contact your national DHOLLANDIA distributor. See page 3 for contact info.
NOTICE
DANGER: indicates an imminently hazardous situation which, if not avoided, will result in death
or serious injury. [white letters on red background]
WARNING: indicates a potentially hazardous situation which, if not avoided, could result in death
or serious injury. [black letters on orange background]
CAUTION: indicates a potentially hazardous situation which, if not avoided, could result in minor
or moderate injury. [black letters on yellow background]
NOTICE: is used to address practices not related to physical injury. [white letters on blue
background]
SAFETY INSTRUCTIONS: indicate general instructions relative to safe work practices,
reminders of proper safety procedures, or the location of safety equipment. [white letters on
green background]
SAFETY
INSTRUCTIONS
SAFETY ALERT SYMBOL: is used to alert the user to potential hazards. All safety messages
that accompany this sign shall be obeyed to avoid possible harm. [free-standing, or on back-
ground colours red, orange, yellow or black]

3
DHOLLANDIA
2CONTACT INFORMATION AND DISCLAIMERS
DHOLLANDIA lifts are regularly being adapted to new vehicle and chassis developments and specialized customer
requirements. Therefore, DHOLLANDIA reserves the right to alter product specifications without prior notice and potentially
modifications or new developments might not have been taken into account at the time of printing.
NOTICE
Please confirm you have reviewed the most up-to-date version of this manual prior to operation of the associated DHOLLANDIA lift.
See below for instructions to download the latest version of the manual.
Contact your national DHOLLANDIA distributor if you have any questions regarding the installation, operation, repair and
maintenance of DHOLLANDIA lifts, to obtain replacement copies of manuals or decals, or to learn about available equipment
options for DHOLLANDIA lifts.
Take notice of following important disclaimers:
DISCLAIMERS
DHOLLANDIA disclaims liability for any personal injury, death or property damage that results from operating a lift that has
been modified from the original design, without explicit written approval from the manufacturer.
DHOLLANDIA disclaims liability for any personal injury, death or property damage that results from the use of aftermarket or
non-OEM replacement parts for service or repair of the lift.
DHOLLANDIA disclaims liability for any personal injury, death or property damage that results from improper use of the lift.
DHOLLANDIA disclaims liability for any personal injury, death or property damage that results from overloading or improperly
loading the platform, disregard of the maximum rated lift capacity and the applicable load charts.
There are no warranties, express or implied, including the warranty of merchantability or a warranty of fitness for a particular
purpose extending beyond that set forth in this manual.
If in doubt where to find your national DHOLLANDIA distributor, visit the official DHOLLANDIA website
www.dhollandia.com → Country selection / language selection → Distributors & service
The latest version of all manuals can also be downloaded from the DHOLLANDIA website
www.dhollandia.com → Country selection / language selection → Downloads → Operation
manuals → … select required manual

4
DHOLLANDIA
3GENERAL INTRODUCTION
The manuals mentioned below apply to various types of lifts DH-P2*, DH-PH2*, DH-P1*, DH-PH1* operating in a similar way.
In case of any doubt, always contact your national DHOLLANDIA distributor. See contact info on page 3.
The DH-PH2* and DH-PH1* are wheelchair lifts , used to assist wheelchair occupants or persons with an impaired mobility
embark and disembark the vehicle. The DH-P2* and DH-P1* are commercial lifts, used to handle cargo.
This OPERATION MANUAL explains how the DHOLLANDIA lift is manufactured, what safety devices are incorporated in its
design and how to use the lift in a correct manner, that preserves the integrity of the machine over the intended lifetime and
helps maximize the safety of the operator and any bystanders.
The MAINTENANCE AND REPAIR MANUAL (separate) explains how to maintain and service the lift in the appropriate manner,
maximizing the safety of the operator and any bystanders and ensuring the reliability of the lift over the intended lifetime.
The CE IDENTIFICATION AND INSPECTION LOGBOOK (separate) contains the serial number identification, the CE
Declaration of Conformity, the Fitting Declaration to be filled out by the installer of the lift, and an overview of the owner’s legal
obligations in terms of periodic testing and certification.
The manuals must be kept with the lift at all times, as a reference book for the operators and technical service.
4INTENDED USE
DHOLLANDIA wheelchair lifts DH-PH2* and DH-PH1* are designed to be fitted to multi passenger vehicles, busses and coaches,
and shall be used exclusively to assist wheelchair occupants or persons with an impaired mobility embark and disembark the vehicle,
within the limits of the load chart, in compliance with the operator instructions and safety instructions described in this manual.
DHOLLANDIA commercial lifts DH-P2* and DH-P1* are designed to be fitted to vans and light-duty commercial vehicles, and shall
be used exclusively to load and unload the goods transported on the vehicle they are fitted to, within the limits of the load chart, in
compliance with the operator instructions and safety instructions described in this manual.
WARNING
Improper use of the lift will put the operator and other parties at great risk of serious bodily injury and death. Therefore, the use
of the lift is restricted to skilled operators only; who have been properly trained, and who know and understand the full contents
of this manual.
Unauthorized modifications to the lift can put the operator and other parties at great risk of serious bodily injury and death.
Therefore, it is strictly forbidden to modify the lift and its safety devices in any way.
The use of aftermarket or non-OEM replacement parts to repair the lift is strictly prohibited and may result in serious bodily
injury or death of the operator or any bystanders.
WARNING
Improper use of the lift will put the operator and bystanders at great risk of serious bodily injury and death. Therefore, it is strictly
forbidden to use the lift in a different way, or for different purposes than described in the operation manual.
The lift must NEVER be used as an elevated work platform, to push loads, to move snow or other debris.
DHOLLANDIA disclaims liability for any personal injury and / or property damage that results from improper use.

5
DHOLLANDIA
5IDENTIFICATION
Every DHOLLANDIA lift is identified by and labelled with a unique 8-digit serial number (with or without a space between the
first and last 4 digits). Use this number for any inquiry on a particular lift, or when ordering replacement parts.
In addition to the lift type and serial number, the various serial number labels provide additional information such as: the
maximum rated lift capacity and load chart, the date of manufacture, etc...
A large label is usually affixed to the
vehicle body near the lift.
Medium sized labels are affixed to
the lift frame, to the platform and to
the power pack.
Small labels are affixed to the
hydraulic cylinders and the electric
motor inside the power pack.

6
DHOLLANDIA
6DESCRIPTION AND TERMINOLOGY
6.1 GENERAL
The DH-PH2* and DH-PH1* are wheelchair lifts , used to assist wheelchair occupants or persons with an impaired mobility
embark and disembark the vehicle. These wheelchair lifts incorporate a number of safety devices that are not required on
commercial lifts
The DH-P2* and DH-P1* are commercial lifts derived from aforementioned wheelchair lifts. They are used to handle cargo.
In this manual the following terms will be used:
1. Lift = refers to both wheelchair and commercial lifts
2. Wheelchair lift = refers to wheelchair applications only abbreviation [W]
3. Commercial lift = refers to commercial cargo handling applications only abbreviation [C]
In one and the same sentence, the abbreviations [W] and [C] will be used to include one type of lift and exclude the other.
DHOLLANDIA lifts are developed and manufactured using state-of-the-art technology, high quality materials and components,
and highly skilled workmanship. They comply with the European CE safety regulations mentioned in the Declaration of
Conformity issued with each lift (unless otherwise agreed for tail lifts exported outside the CE region).
The DH-P2* and DH-PH2* are fully automatic twin-arm lifts, holding the platform at both sides, providing maximum stability and
additional lift capacity.
In travel position, the platform and lift frame are stowed in upright position, just in front of the vehicle doors. Upon deployment,
the platform is tilted down from a vertical travel position to a horizontal work position. Guard rails, the bridge plate at the inboard
platform edge and roll stop at the outboard platform edge are deployed automatically.
The DH-P1* and DH-PH1* are operated by a single arm, holding the platform at 1 side only. In standard execution, they have
a fixed frame, the closed platform stands in the door aperture. Option OWU006 features a rotating frame, so that the platform
can be swung out of the way to a travel position at the side of the vehicle body.
In travel position, the platform and lift frame are stowed in upright position, just in front of the vehicle doors (standard execution),
or swung out of the way against the side of the vehicle body (option OWU006). Upon deployment, the lift frame is swung into
the door aperture (only for OWU006). Then the platform is tilted down from a vertical travel position to a horizontal work position.
The guard rail, bridge plate at the inboard platform edge and roll stop at the outboard platform edge are deployed automatically.
Main details and terminology: see below.
DH-PH2* / DH-P2* ●TERMINOLOGY
See figure below for parts corresponding to numbers in this table
#
Description
1
Lift frame: steel assembly incorporating the lift arms and lift cylinders, who together carry the platform. The lift frame is
mounted in a fixed position on the vehicle floor.
2
Lift arms + lift cylinders: 2 lift arms L+R actuated by the lift cylinders, used to lift / lower the platform and its load (=
functions UP / DOWN).
3
Platform: carries the load during lifting / lowering. It is equipped with a bridge plate at the inboard platform edge and a roll
stop at the outboard platform edge. The guard rails for the platform are integrated in the 2 lift arms.
[W] →Platform in mesh steel, evacuating rainwater, snow, dirt, etc. quickly through the platform surface.
[C] →Steel platform frame filled with aluminium profiles with non-slip ripples.
3a
Platform wings [OWU002 = vertical split platform]: the platform incorporates 2 articulated platform sections that swing
down and form a closed platform surface when the lift is deployed in its work position; and swing up and create an open
space between the lift arms when the lift is stowed in its travel position.
3b
Platform main section [OWU003 = horizontally foldable platform]: inboard main section of the foldable platform, attached
to the lift arms.

7
DHOLLANDIA
3c
Foldable point [OWU003 = horizontally foldable platform]: foldable point of the platform, folded automatically as the
platform is deployed or stowed.
4
Bridge plate: plate mounted at the inboard platform edge, used to bridge any gap between the platform and the vehicle
floor when the platform is raised to its maximum height.
5
Roll stop: roll stop mounted at the outboard platform edge. The roll stop is tilted up automatically when the platform leaves
the ground, it is tilted down automatically when the platform touches the ground.
[W] → The roll stop prevents the wheelchair from slowly and unexpectedly rolling off the platform during lifting and lowering.
It is not designed to stop fast and powered movements. See also 7.4 on page 22
6
Guard rails [W]: fall protections at both sides of the platform, protecting the wheelchair occupant and his attendant from
falling off the platform. The guard rails are integrated in the lift arms. They are deployed and stowed automatically in
synchronisation with the movement of the platform.
7
Flashing platform lights: used to make the platform visible to other parties in traffic.
8
Platform lock: Mechanical lock to prevent the platform from falling open in case of an accidental loss of hydraulic pressure.
3 types of locks are available:
1. Standard ref. OWF014.1: lock with gas cylinder mounted on 1 side only. This lock only engages in case of a slow
hydraulic pressure loss. In normal conditions at full pressure, it remains inactive.
2. Option OWF014.2: same as above, but mounted on both sides of the lift.
3. Option OWF015: Lock with springs instead of gas cylinders. This lock engages automatically when platform is
closed, and must be released manually every time before opening the platform.
9
Wander lead with spiral cable: control box to execute all functions DEPLOY –UP –DOWN - STOW.
[W] →3-button wander lead with a safety stop at the vehicle floor prior to stowing the platform [= ref. OWE002]. A 4-button
execution [= option OWE003] is available as an option.
[C] →2-button wander lead with for all 4 functions. A 3-button execution [= option OWE002] and 4-button execution [=
OWE003] are available as an option.
10
Hydraulic power pack: contains the electric motor driving the hydraulic pump, the oil tank, and the control valves.
DH-PH2* ● TWIN ARM LIFT WITH STANDARD PLATFORM ● TERMINOLOGY
INBOARD
platform
edge
OUTBOARD
platform edge

8
DHOLLANDIA
DH-PH2* + OWU002 ● TWIN ARM LIFT WITH VERTICAL SPLIT PLATFORM ● TERMINOLOGY
DH-PH2* + OWU003 ● TWIN ARM LIFT WITH HORIZONTALLY FOLDABLE PLATFORM ● TERMINOLOGY
INBOARD
platform
edge
OUTBOARD
platform edge
INBOARD
platform
edge
OUTBOARD
platform edge

9
DHOLLANDIA
DH-PH1* / DH-P1* ●TERMINOLOGY
See figure below for parts corresponding to numbers in this table
#
Description
1
Main column: steel assembly incorporating the lift frame, lift arm and lift cylinder. The main column is mounted in a fixed
position on the vehicle floor and additionally attached to the side of the vehicle body. Following types are available:
1. Standard: fixed column. The main column and lift frame are one and the same assembly. The platform has only
1 travel position just in front of the vehicle doors.
2. Option OWU006: free-access execution. The lift frame can pivot on the main column. The platform can swing
from a travel position against the side of the vehicle body to a work position in the door aperture.
2
Lift frame: steel assembly incorporating the lift arm and lift cylinder, who together carry the platform.
3
Lift arm + lift cylinder: a single lift arm actuated by a lift cylinder, used to lift / lower the platform and its load (= functions
UP / DOWN).
4
Platform: carries the load during loading / unloading, lifting / lowering. It is equipped with a bridge plate at the inboard
platform edge and a roll stop at the outboard platform edge. The guard rail for the platform is integrated in the lift arm.
[W] →Platform in mesh steel, evacuating rainwater, snow, dirt, etc. quickly through the platform surface.
[C] →Steel platform frame filled with aluminium profiles with non-slip ripples.
5
Bridge plate: plate mounted at the inboard platform edge, used to bridge any gap between the platform and the vehicle
floor when the platform is raised to its maximum height.
6
Roll stop: roll stop mounted at the outboard platform edge. The roll stop is tilted up automatically when the platform leaves
the ground, it is tilted down automatically when the platform touches the ground.
[W] → The roll stop prevents the wheelchair from slowly and unexpectedly rolling off the platform during lifting and lowering.
It is not designed to stop fast and powered movements. See also 7.4 on page 22
7
Guard rail [W]: fall protection at the side of the platform, protecting the wheelchair occupant and his attendant from falling
off the platform. The guard rail is integrated in the lift arms. It is deployed and stowed automatically in synchronisation with
the movement of the platform.
8
Flashing platform lights: used to make the platform visible to other parties in traffic.
9
Platform lock: Mechanical lock to prevent the platform from falling open in case of accidental loss of hydraulic pressure.
The lock incorporates a gas cylinder and only engages in case of a slow hydraulic pressure loss. In normal conditions at
full pressure, it remains inactive.
10
Pivot lock [OWU006 = pivoting frame]: unlock and lock the pivot lock to pivot the lift frame from a travel position against
the side of the vehicle body to a work position in the door aperture and vice versa.
11
Wander lead with spiral cable: control box to execute all functions DEPLOY –UP –DOWN - STOW. The wander lead
features 2 buttons for 4 functions.
12
Hydraulic power pack: contains the electric motor driving the hydraulic pump, the oil tank, and the control valves.

10
DHOLLANDIA
DH-PH1* ● 1 ARM LIFT WITH STANDARD PLATFORM ● TERMINOLOGY
INBOARD
platform
edge
OUTBOARD
platform edge

11
DHOLLANDIA
POWER PACK ●TERMINOLOGY
See figure below for parts corresponding to numbers in this table
#
Description
1
Power pack: sealed box containing the electric motor and hydraulic pump, the oil tank, control valves, electronic control
unit and various emergency controls that can be operated in case of an electrical power failure.
2
Removable cover: can be removed to get access to the electric motor and hydraulic pump, the oil tank, control valves
and electronic control unit.
3
Hydraulic hand pump: manual back-up pump to lift the platform in case of an electrical power failure (= function UP). The
lever [# 3a] for the hand pump is stored at the front face of the cover of the power pack.
4
Emergency Descent button: manual back-up button to lower the platform in case of an electrical power failure (=function
DOWN).
5
Main battery disconnect switch: switch to switch the main power from the vehicle battery to the lift on / off.
It will stop the lift in case of emergency involving hazard to the operator or wheelchair occupant.
It will stop the lift and reduce the risk of a power pack burn-out if the starter solenoid is stuck and the motor runs
continuously (control button or contact damaged, starter solenoid short circuited by low voltage).
6
Electric connection: plug for the connection of the wander lead with spiral cable
1
1
2
2
3
3
3a
3a
4
4
5
5
6
6

12
DHOLLANDIA
6.2 SAFETY DEVICES
DHOLLANDIA lifts are equipped with a multiple safety devices to enable its intended use with a maximum degree of safety for
the operator, the wheelchair occupant on the platform and any incidental bystanders. The following safety devices are
incorporated on the DH-P*... Series:
N°
Description
Image
1
Non-slip surface: the platform surface incorporates an non-slip profiling to
prevent the operator and platform occupants from slipping and falling.
[W] →Platform in mesh steel, evacuating rainwater, snow, dirt, etc. quickly
through the platform surface.
[C] →Steel platform frame filled with aluminium profiles with non-slip ripples.
2
Roll stop: roll stop mounted at the outboard platform edge. The roll stop is tilted
up automatically when the platform leaves the ground, it is tilted down
automatically when the platform touches the ground.
The roll stop prevents the wheelchair from slowly and unexpectedly rolling off the
platform during lifting and lowering. It is not designed to stop fast and powered
movements. See also 7.4 on page 22
3
Guard rail(s) [W]: fall protections mounted at both sides of the DH-PH2* platform
(*), protecting the wheelchair occupant and his attendant from falling off the
platform. The guard rails are deployed and stowed automatically in
synchronisation with the movement of the platform.
(*) 1 guard rail only on the 1-arm lift DH-PH1*
4
Bridge plate: plate mounted at the inboard platform edge, used to bridge any gap
between the platform and the vehicle floor when the platform is raised to its
maximum height.
The bridge plate tilts down automatically as the platform approaches the vehicle
floor. It tilts up automatically as the platform lowers to the ground.
It also forms a toe-guard for the operator and the wheelchair occupant while
travelling up / down on the platform.

13
DHOLLANDIA
5
Flashing platform lights: used to make the platform visible to other parties in
traffic.
7
End stop for STOW [W]: DH-PH2* wheelchair lifts are supplied with a 3-button
wander lead and a safety stop at the end of each lift movement (= UP) before the
platform can be closed (= STOW).
On DH-P* lifts equipped with a 2-button wander lead, the platform will stop at the
vehicle floor if the platform is loaded and the UP button of the wander lead
released upon arrival. The platform will continue to close (= STOW) if the platform
is empty and the UP button kept activated.
8
Platform lock: Mechanical lock to prevent the platform from falling open in case
of a slow loss of hydraulic pressure.
See also terminology description above for differences between DH-P2 / PH2*
and DH-P1 / PH1*.
9
Main battery disconnect switch: switch to switch the main power from the
vehicle battery to the lift on / off.
It will stop the lift in case of emergency involving hazard to the operator
or wheelchair occupant.
It will stop the lift and reduce the risk of a power pack burn-out if the
starter solenoid is stuck and the motor runs continuously (control button
or contact damaged, starter solenoid short circuited by low voltage).
10
Main battery fuse: a main fuse 100 –150A is supplied by the vehicle
manufacturer or by DHOLLANDIA. It protects the main battery cable from the
batteries to the power pack of the lift against short circuits and amperage peaks.

14
DHOLLANDIA
11
15A fuse: lighter fuses are used to protect the control unit, associated wires and
the printed circuit against short circuits and amperage peaks.
14
Emergency descent button: manual back-up button to open (= DEPLOY) and
lower (= DOWN) the platform in case of an electrical power failure.
16
Hydraulic hand pump: manual back-up pump to lift the platform in case of an
electrical power failure (= UP).
17
Pressure relief valve: safety device integrated in the power pack, enabling the manufacturer and the installer of the lift to limit
the real lift capacity to the maximum rated capacity of the lift sold, and protect it against overload while lifting (= UP).
18
Pressure compensated flow valves: flow valves are integrated in the hydraulic circuits to ensure the platform lowers at a safe
speed, both empty and when fully loaded.
19
Decals: the lifts are supplied with a number of operation decals, load diagrams and safety decals. Some of these decals are
premounted by DHOLLANDIA on the lift. Some of these decals are supplied loose and shall be affixed by the installer near to the
lift at a location clearly visible to the operator.
The decals must be kept clean and legible at all times, and replaced whenever required.

15
DHOLLANDIA
7SAFETY INSTRUCTIONS FOR USING THE LIFT
7.1 DO NOT USE THE LIFT WITHOUT ADEQUATE SAFETY AND OPERATOR TRAINING
DHOLLANDIA lifts shall be exclusively use in accordance with the INTENDED USE as described in section 4 on page 4, within
the limits of the applicable load chart, in compliance with the operator instructions and safety instructions in this manual.
The operator should follow all other policies and procedures applicable to the job situation including health and safety
regulations, road and traffic regulations, as well as company procedures. The operator should not use the lift if he/she cannot
use it in accordance with all applicable regulations and instructions.
The operator must be at least 18 years of age.
7.2 GENERAL SAFETY INSTRUCTIONS
WARNING
To avoid serious bodily injury or death, the operator must use appropriate work clothes. NEVER wear loose-fitting clothes that
may be trapped in the moving parts of the wheelchair lift. ALWAYS wear professional safety-toe shoes, protective gloves, and
eye protection. Use of a hardhat is recommended.
Must
Recommended
Slipping (and falling) can result in serious bodily injury and death. To prevent injury by slipping:
oALWAYS wear professional safety-toe shoes with a good non-slip sole.
oDO NOT use the lift if it is covered with snow, mud, dirt, debris, liquids or other substances.
oDO NOT run on the platform.
Tripping (and falling) can result in serious bodily injury and death. To prevent injury by tripping:
oDO NOT use lift platform as a step. NEVER leave the lift unattended in partially deployed position.
oPay attention to protruding items on the platform surface at all times (ex. platform lights, roll stops and their
levers, foreign objects, etc…).
oDO NOT run on the platform.
Falling from the platform can result in serious bodily injury and death. To prevent injury by falling:
oMake sure your footing is solid and you maintain 3 points of contact (2 feet on the platform, 1 hand on a
guard rail).
oUse guard rails where available. See 7.4 from page 22 onwards.
oNEVER move the vehicle while a person is standing on the platform or inside the vehicle body.
oNEVER use the platform as an elevated working platform.
WARNING
Improper use of the lift will put the operator and other parties at great risk of serious bodily injury and death.
To reduce the risk of serious bodily injury to the operator and any bystanders, the use of the lift is restricted to skilled operators,
who have been properly trained, and who know and understand the full contents of this manual.
To reduce the risk of serious bodily injury or death, THE OPERATOR MUST COMPLY WITH ALL SAFETY INSTRUCTIONS
AND WARNING LABELS IN THIS SECTION AND THE ENTIRE MANUAL before and while operating the lift.

16
DHOLLANDIA
WARNING
Prior to operating the lift, the vehicle must be safely parked on level and solid ground, have the parking brake applied, and the
engine switched off. Open any doors located in front of the lift and secure any moving parts of the vehicle body. Failure to abide
by these instructions can result in serious bodily injury or death to the operator or bystanders.
Prior to deploying the platform, check if the lift can be used safely. Take precautions to ensure your own safety, and the safety
of bystanders or other parties in traffic. Clear the working area of any objects that could potentially impede movement of the lift.
Failure to abide by these instructions can result in serious bodily injury or death to the operator or bystanders.
To reduce the risk of serious bodily injury or death which may result from other vehicles when parked, ALWAYS make sure a
safety distance of 16 ft or 5 m is kept between the back of the vehicle and the following vehicle.
Ensure that the vehicle cannot tip-over when putting weight on the platform. If the vehicle is equipped with mechanical or
hydraulic stabilizing legs, deploy these before opening the platform. Ensure that the stabilizing legs are positioned on solid even
ground. In case of soft terrain (sand, gravel…), solid support blocks must be used under the stabilizing legs. Failure to abide by
these instructions can result in serious bodily injury or death to the operator or bystanders.
To reduce the risk of serious bodily injury or death, ALWAYS
make sure the platform is clearly visible to other persons from
all approach directions. The lifts are equipped with flashing
platform lights. Nevertheless, DHOLLANDIA recommends
the use of 4 warning cones, placed around the work area of
the platform.
To reduce the risk of serious bodily injury or death, make sure
the working zone is sufficiently lighted.

17
DHOLLANDIA
WARNING
Inspect the lift prior to each use. If any unsafe condition exists or unusual noises or movements are noticed, DO NOT use the
lift and contact an authorized DHOLLANDIA service agent for repair. Please see ‘pre-trip inspection’ procedures under 7.6 from
page 25 onwards.
Read and comply with all warning decals, pictograms and instructions affixed to the lift. Failure to abide by warnings and
instructions may result in serious bodily injury or death.
The lift must not be used if the operator is intoxicated, impaired or distracted in any way. NEVER use a phone or mobile device
when operating the lift.
The lift shall be used by means of original control units only. Operating the lift with unauthorized control units will increase risk
of serious bodily injury or death to the operator or any bystanders.
Limit the operation of the lift to one single operator. Operation of the lift by more than one operator at a time may cause confusion
and increase the risk of serious bodily injury or death.
To prevent people from being hit by the platform, by objects falling off the platform; being caught in pinch points or being pinched
by the moving parts of the lift:
Keep visual control over the entire working area of the lift and its platform at all times, including the
area DIRECTLY BEHIND and UNDER the platform.
Upon deployment, DO NOT allow any other person to stand in the proximity of the lift and its platform.
ENSURE AT ALL TIMES THAT NOBODY STANDS UNDER OR WITHIN REACH OF THE MOVING
PLATFORM.
Prior to opening the doors, make sure that the lift has not lost its hydraulic pressure and is not leaning
against the doors. When opening the doors and deploying the platform, ALWAYS stand clear of the
range of motion of the platform!
Upon lifting and lowering: DO NOT allow any other person, except the person to be lifted or lowered,
to be in the proximity of the lift and its platform.
Careful supervision is necessary if used on behalf of, or near children.
NEVER leave the lift unattended in open position. Before leaving the vehicle unattended, close the doors of the vehicle, stow
the platform in its travel position and switch off the electrical power to the lift. Leaving the lift in open position unattended can
result in serious bodily injury or death to unaware bystanders. See 8 from page 27 onwards for instructions on properly stowing
platform into its travel position.
NEVER move the vehicle with the lift in the open position. ALWAYS stow the lift in its travel position, close and secure the
doors of the vehicle and switch off the electrical power to the lift before moving the vehicle. Failure to properly stow the lift in its
travel position prior to moving the vehicle may result in serious bodily injury or death.

18
DHOLLANDIA
NOTICE
The safety instructions in this manual are drawn up with an average, common use of the lift in mind.
For specific applications or work conditions, other instructions might be appropriate to reach a higher level of safety. If contra-
indications exist, a formal risk analysis must be performed by the client’s health and safety management and safe work
procedures for the drivers and operators must be issued.
WARNING
Use of the lift near vehicular traffic may result in serious bodily injury or death from being struck by another vehicle. When
operating the lift on or near a street or parking lot, be sure to stay clear of vehicular traffic. ALWAYS be sure to clearly identify
to other drivers that the lift is in use. DHOLLANDIA recommends use of warning cones to clearly identify to drivers that the lift
is being operated. When the lift is operated near vehicular traffic, wear working clothes in high-visibility colours and a retro-
reflective safety vest.
DO NOT raise the lift with the rear doors partially open. Doing so may damage the doors or the lift platform and may also result
in serious bodily injury or death to the operator or any bystanders.
Above all, USE GOOD COMMON SENSE when operating the lift. DO NOT operate the lift until the contents of this manual
have been read and fully understood. Improper use of the lift increases the risk of serious bodily injury or death to the operator
and any bystanders.

19
DHOLLANDIA
7.3 DANGER ZONES, RISK OF CRUSH AND SHEAR INJURY
There are several main danger zones on and around the platform, that can be hazardous to the operator and any other
persons nearby.
ALWAYS stay clear of the area behind the
platform and the range of motion of the
platform.
ALWAYS beware of the crushing zone
between the lowering platform and the ground
WARNING
Impact by the platform or the moving parts
of the lift will result in serious bodily injury
or death. To prevent people from being hit
by the platform, by objects falling off the
platform or being caught in pinch points or
being pinched by the moving parts of the
lift:
Keep visual control over the entire
working area of the lift at all times,
including the area directly behind and
under the platform;
DO NOT allow any person to stand
near the lift and its platform. Ensure at
all times that nobody stands under, or
within reach of the moving platform
and its load.
WARNING
Lowering an empty or fully loaded platform
on one’s feet may result in serious bodily
injury. To prevent people from having their
feet crushed or sheared by the lowering
platform:
Keep visual control over the entire
working area of the lift at all times,
including the area directly behind and
under the platform;
When operating the lift from a position
on the ground, ALWAYS stand at the
side of vehicle body, at a safe
distance of minimum 50 cm away
from the moving platform.
Correct operator position
Danger zone