Dhollandia DH-S Series User manual

Doc: FIT_S_US_EN_2019_rev4 Rev: 4Date: OCTOBER 14, 2019
Manufacturer:
DHOLLANDIA US, L.L.C.
Tel : [phone] E-mail : [email protected]
132 W Virginia Ave
Bessemer City North Carolina, 28016
website : www.dhollandia.com
DH-S*
INSTALLATION MANUAL
Read the manual in its entirety before operating the liftgate
Keep this manual in the vehicle cab, as reference for the driver and liftgate operator
900–6,600lbs (400-3000kg)
** Pictured: SM.20 liftgate

1
DHOLLANDIA
Contents
1UNDERSTANDING SAFETY AND WARNING SIGNS...................................................................................................................... 3
2INTRODUCTION AND DISCLAIMERS ............................................................................................................................................. 4
3CONTACT INFORMATION ............................................................................................................................................................... 5
4SAFETY PRECAUTIONS FOR OPERATION ................................................................................................................................... 6
5SAFETY PRECAUTIONS FOR INSTALLATION............................................................................................................................... 6
6LIFTGATE TERMINOLOGY .............................................................................................................................................................. 9
6.1 DH-S* liftgate terminology......................................................................................................................................................... 9
6.2 Installation parameters terminology ........................................................................................................................................ 11
6.3 Getting started......................................................................................................................................................................... 14
6.4 Installation dimensions............................................................................................................................................................ 15
7TYPES OF CHASSIS AND FITTING METHODS............................................................................................................................ 19
8MOUNTING OF THE LIFT FRAME: 3 WAYS TO GET STARTED.................................................................................................. 20
8.1 Method with the fitting jigs....................................................................................................................................................... 20
8.2 Method with horizontal platform .............................................................................................................................................. 21
8.3 Using the quick-fit transport rack (option S410) ...................................................................................................................... 22
9MOUNTING OF THE LIFT FRAME AND SLIDING TUBES ............................................................................................................ 23
9.1 Test fitting the LIFT frame and sliding tubes ........................................................................................................................... 23
9.2 Position of the mounting brackets on the aluminium sliding tubes for DH-SM(R) 1500-2000 kg ............................................ 26
9.3 Differences for DH-SSU(R) 2000-3000 kg and DH-SK(S) 1000-2000 kg................................................................................ 28
9.4 Steel sliding tubes ................................................................................................................................................................... 29
9.5 Mounting the sliding tubes to the vehicle chassis.................................................................................................................... 29
9.6 Adjustment and fastening of the slide plates........................................................................................................................... 32
10 MOUNTING THE PLATFORM & FINALIZING THE MECHANICAL WORK.................................................................................... 34
10.1 Mounting the platform to the lift arms...................................................................................................................................... 34
10.2 Check the position of the tooth rack of the retraction system.................................................................................................. 35
10.3 Mount the end stops for the work position............................................................................................................................... 36
10.4 Finalize the stow position of the platform ................................................................................................................................ 38
11 ELECTRICAL INSTALLATION ........................................................................................................................................................ 41
11.1 Installation of the main control box.......................................................................................................................................... 41
11.2 Optional mounting brackets..................................................................................................................................................... 42
11.3 Routing of the electric cables .................................................................................................................................................. 43
12 PUTTING THE LIFTGATE INTO SERVICE..................................................................................................................................... 46
13 LUBRICATION INSTRUCTIONS..................................................................................................................................................... 47
14 COMMISSIONING AND QUALITY CONTROL................................................................................................................................ 50
15 DECALS .......................................................................................................................................................................................... 51
15.1 Regular decals ........................................................................................................................................................................ 51
15.2 Use of the ‘WARNING: LIFTGATE OUT OF SERVICE. DO NOT ATTEMPT TO OPERATE’ sign ........................................ 54
15.3 Identification decals................................................................................................................................................................. 55
16 APPENDIX....................................................................................................................................................................................... 56

2
DHOLLANDIA
16.1 Decals ..................................................................................................................................................................................... 56
16.2 Prescribed torque values for bolts supplied with liftgate.......................................................................................................... 58
16.3 PDI checklist 1/2...................................................................................................................................................................... 60
16.4 Safe operator position on the platform .................................................................................................................................... 63
16.5 2-button portable control ......................................................................................................................................................... 64
16.6 Circuit breaker......................................................................................................................................................................... 68
16.7 Cab cut-off switch.................................................................................................................................................................... 69
16.8 Electric and hydraulic information ........................................................................................................................................... 70
16.9 Mounting diagrams.................................................................................................................................................................. 79
16.10 End note.................................................................................................................................................................................. 81

3
DHOLLANDIA
1UNDERSTANDING SAFETY AND WARNING SIGNS
•Many safety signs and symbols used in this manual are based on international standards, others refer to specific situations or
actions.
•Consult Appendix 1 for an overview of signs and symbols used in DHOLLANDIA manuals, and their meaning. Make sure you
understand these signs and symbols prior to starting the installation.
Examples of standard ANSI
signs
Examples of DHOLLANDIA
purpose made signs
•Please take special notice of the following signs used in the manual. They indicate the likelihood and severity of a potential injury if
a person fails to follow the instructions presented on the safety sign.
NOTICE
DANGER: indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury. [white letters on red background]
WARNING: indicates a potentially hazardous situation which, if not avoided, could result in death
or serious injury. [black letters on orange background]
CAUTION: indicates a potentially hazardous situation which, if not avoided, could result in minor or
moderate injury. [black letters on yellow background]
NOTICE: is used to address practices not related to physical injury. [white letters on blue
background]
SAFETY INSTRUCTIONS: indicate general instructions relative to safe work practices, reminders
of proper safety procedures, or the location of safety equipment. [white letters on green background]
SAFETY
INSTRUCTIONS
SAFETY ALERT SYMBOL: is used to alert the user to potential hazards. All safety messages that
accompany this sign shall be obeyed to avoid possible harm. [free-standing, or on back-ground
colours red, orange, yellow or black]

4
DHOLLANDIA
WARNING
•Failure to understand and to follow the instructions in this manual can put the operator and any bystanders at great risk of serious
bodily injury and death.
•Prior to operating the liftgate, make sure you understand the safety and warning signs used, and read them in conjunction with the
instructions in this manual.
•If in doubt, DO NOT operate the liftgate. Contact your national DHOLLANDIA distributor. See page 5 for contact info.
2INTRODUCTION AND DISCLAIMERS
•This manual provides you with the information necessary for the installation of the DHOLLANDIA DH-LM liftgate.
•It provides you with general instructions applicable to the common truck and trailer types. It might be possible that specific issues
particular to your installation case are not adequately covered by this manual. If in doubt, please contact your local DHOLLANDIA
distributor for further assistance.
•DHOLLANDIA liftgates are regularly being adapted to new vehicle and chassis developments and specialized customer requirements.
Therefore, DHOLLANDIA reserves the right to alter product specifications without prior notice. Such modifications might not have
been included at the time this manual was printed.
NOTICE
•Please confirm you have reviewed the most up-to-date version of this manual prior to installation and operation of the associated
DHOLLANDIA liftgate.
•It is the sole responsibility of the installer(s) to follow shop best practices for safety and craftsmanship and to use good common
sense.
•Contact your national DHOLLANDIA distributor if you have any questions regarding the installation, operation, repair and
maintenance of DHOLLANDIA liftgates, or to obtain replacement copies of manuals or decals:
WARNING
•Improper installation can cause damage to the liftgate, reduce the durability and reliability of the liftgate, and put the operator and
bystanders at great risk of serious bodily injury and death in many ways.
•It is therefore essential that the liftgates are installed with proper care, in compliance with the installation instructions of this manual.
•In case of doubt, ALWAYS contact your national DHOLLANDIA distributor for further advice prior to continuing.

5
DHOLLANDIA
3CONTACT INFORMATION
DHOLLANDIA liftgates are regularly being adapted to new vehicle and chassis developments and specialized customer requirements.
Therefore, DHOLLANDIA reserves the right to alter product specifications without prior notice; and potentially modifications or new
developments might not have been taken into account at the time of printing.
NOTICE
Please confirm you have reviewed the most up-to-date version of this manual prior to operation of the associated DHOLLANDIA liftgate.
See below for instructions to download the latest version of the manual.
Contact your national DHOLLANDIA distributor if you have any questions regarding the installation, operation, repair and maintenance of
DHOLLANDIA liftgates, to obtain replacement copies of manuals or decals, or to learn about available equipment options for
DHOLLANDIA liftgates.
•Take notice of following important disclaimers:
DISCLAIMERS
•DHOLLANDIA disclaims liability for any personal injury, death, or property damage that results from operating a liftgate that has
been modified from the original design, without explicit written approval from the manufacturer.
•DHOLLANDIA disclaims liability for any personal injury, death, or property damage that results from use of aftermarket or non-
OEM replacement parts for service or repair of the liftgate.
•DHOLLANDIA disclaims liability for any personal injury, death, or property damage that results from improper use of the liftgate.
•DHOLLANDIA disclaims liability for any personal injury, death, or property damage that results from overloading or improperly
loading the platform, disregard of the maximum rated lift capacity and the applicable load charts.
•There are no warranties, express or implied, including the warranty of merchantability or a warranty of fitness for a particular purpose
extending beyond that set forth in this manual.
The latest version of all manuals can also be downloaded from the DHOLLANDIA website
www.dhollandia.com → Downloads → User’s manuals → … select required manual
DHOLLANDIA US, LLC
United States - East
200 Hilton Street West
Easton PA 18042
Tel: [phone]
[e-mail]
DHOLLANDIA CANADA, Inc.
Canada
2105 Boulevard des Entreprises
Terrebonne Quebec J6Y1W9
Tel: [phone]
[e-mail]
DHOLLANDIA MEXICO, Inc.
Mexico
Fraccionamiento Industrial
Dinamo del Norte,
Calle Tierra 103-105
C.P. 65500, Salinas Victoria,
Monterrey- Nuevo Leon
Tel: [phone]
[e-mail]
DHOLLANDIA US, LLC
United States - West
12968 Santa Ana Avenue
Fontana CA 92337
Tel: [phone]
[e-mail]

6
DHOLLANDIA
4SAFETY PRECAUTIONS FOR OPERATION
•It is essential that the personnel involved in installing, servicing and repairing liftgates knows, understands and applies
the safety instructions and precautions contained in the OPERATION MANUAL issued with the liftgate.
•Therefore, make sure you consult the OPERATION MANUAL prior to installing or operating the liftgate.
5SAFETY PRECAUTIONS FOR INSTALLATION
•It is essential that the personnel involved in installing, servicing and repairing liftgates knows, understands and applies
the safety instructions and precautions contained in the GENERAL SAFETY INSTRUCTIONS FOR INSTALLATION,
MAINTENANCE AND REPAIR manual.
•Therefore, make sure you consult the GENERAL SAFETY INSTRUCTIONS FOR INSTALLATION, MAINTENANCE
AND REPAIR manual prior to installing the liftgate.
•These instructions are supplied as a separate manual with your liftgate.
•You can also contact your national DHOLLANDIA distributor for the latest edition of this manual. See page 5 for
contact info. Or download the latest edition from the website:
www.dhollandia.com
your language →Downloads →User’s manuals → General information
WARNING
•Improper use of the liftgate will put the operator and other parties at great risk of serious bodily injury and death.
•To reduce the risk of serious bodily injury to the operator and any bystanders, the use of the liftgate is restricted to skilled operators,
who have been properly trained, and who know and understand the full contents of the operation manual.
•To reduce the risk of serious bodily injury or death, THE OPERATOR MUST COMPLY WITH ALL SAFETY INSTRUCTIONS AND
WARNING LABELS IN THE OPERATION MANUAL before and while operating the liftgate.
•Please confirm you have reviewed the most up-to-date version of this manual prior to installation and operation of the associated
DHOLLANDIA liftgate.

7
DHOLLANDIA
WARNING
•The personnel involved in liftgate installation are exposed to various dangers. Improper use of the liftgate, or ignorance and neglect
during installation, will put the personnel at great risk of bodily injury and death.
•Improper installation can cause damage to the liftgate, can reduce the durability and reliability of the liftgate, and can put the operator
and bystanders at great risk of serious bodily injury and death in many ways.
•To reduce the risk of serious bodily injury or death to the installation personnel, to the operator, and any bystanders, liftgate
installation works MUST be restricted to skilled and trained technicians, who have been duly and professionally trained, and know,
understand and apply the manuals of the liftgate:
1. OPERATION MANUAL
2. INSTALLATION MANUAL
3. GENERAL SAFETY INSTRUCTIONS FOR INSTALLATION, MAINTENANCE AND REPAIR
•ALWAYS confirm you have reviewed the most up-to-date version of these manuals prior to installation and operation of the
associated DHOLLANDIA liftgate.
•In case of doubt, ALWAYS contact your national DHOLLANDIA distributor for further advice, prior to continuing.
•ALWAYS wear appropriate Personal Protective Equipment. This includes but may not be limited to: ANSI rated glasses with side
guards, or a wrap-around face shield; steel toe safety shoes; fire-resistant overalls; protective gloves; adequate ear protection; a
safety helmet when working under the vehicle chassis.
•NEVER wear loose-fitting clothes that may get trapped in the moving parts of the liftgate, or in any machinery and tools used for the
installation. Don’t wear rings, bracelets, necklaces, watches etc…
•ALWAYS use the proper tool for the job. Repair or replace worn or damaged tools before use.
•Pay special attention to the lifting devices (forklifts, overhead cranes, hoists, chains or ropes…) used to handle the liftgates, and for
the clamping tools (C-clamps, pipe clamps, vise grips) used to clamp the liftgate, its mounting plates and floor extension to the
vehicle chassis and box. Ensure these tools are appropriate for the job, and in good working order.
•Place the vehicle on a flat even ground and chock the wheels so that it cannot move during the installation process. In case of a
motor vehicle, make sure the engine is off and the parking brake is set before starting.
•Do not work underneath the liftgate, or within reach of the platform and the moving parts of the liftgate, without properly securing
and supporting the platform and the liftgate frame against accidental falling. Use an overhead crane and hoists, a forklift or equivalent
means to secure the heavy liftgate components.
•Make sure the vehicle battery power is disconnected while installing the liftgate. Connect the battery power to the liftgate only when
the installation is completed, or as required in the installation instructions.
•Before welding, note that welding on galvanized parts releases hazardous fumes. Provide adequate ventilation,
and wear an appropriate toxic fume rated welding respirator.
•NEVER modify DHOLLANDIA liftgates or their mounting plates without prior written consent by the manufacturer
•If for any reason, trouble-shooting and / or repair might be needed during the installation process, consult and
follow the guidelines and safety instructions of the MAINTENANCE MANUAL.

8
DHOLLANDIA
NOTICE
•Make sure the vehicle battery power is disconnected while installing the liftgate. Connect the battery power to the liftgate only when
the installation is completed, or as required in the installation instructions.
•Except for the support channels and bracing of the side steps, which are usually welded to the cross members of the auxiliary
chassis, DHOLLANDIA liftgates are designed as a bolt-on system, and don’t require any welding. See Appendix 2 for
prescribed torque values.
•Welding should be done by qualified personnel only, and only to the extent allowed by the vehicle manufacturer. Ensure that the
positive and ground cables are disconnected from the batteries, and that all vehicle electrical and electronic equipment is fully
isolated before welding.
•ALWAYS keep the ground clamp as close as possible to the weld location.
WARNING
NEVER modify DHOLLANDIA liftgates or their mounting plates, NEVER deviate from the described installation procedures without prior
written consent by the manufacturer.

9
DHOLLANDIA
6LIFTGATE TERMINOLOGY
6.1 DH-S* LIFTGATE TERMINOLOGY
See [Figure 6.1] on next page for parts corresponding to numbers in this table
#
Description
1
Platform Assembly: combination of the main and flip sections of the platform.
2
Platform, Main Section: inboard section of the foldable platform. Manufactured from steel or lightweight aluminium, with a
permanent non-slip working surface.
3
Platform, Flip Section: carries the load during loading / unloading, lifting / lowering. Consists of a platform main section and a
flip-over point.
4
Platform Pitch Adjustment bolts: bolts that adjust the angle of the main and flip section of the platform.
5
Platform Knuckle Assembly: assembly responsible for allowing the platform to pivot.
6
Lift Arm Weldment: support brace between the parallel lift arms.
7
Lifting Cylinder: hydraulic cylinders used to LIFT / LOWER the lift arms, the platform and its load.
8
Tilt Cylinder: hydraulic cylinders used to control the pitch of the lift platform.
9
Mounting Brackets: used to mount the sliding tubes to the vehicle chassis.
10
Sliding Tube: steel channels mounted to the underside of the vehicle body allowing the platform to slide.
11
Slide Plate: used to mount the lift frame to the sliding tubes.
12
Lift Frame: box beam connecting all main lifting components.
13
Gear Wheel and Tooth Rack: actuates the sliding function of the platform.
14
Auto Tilt Brackets (L+R): allow the platform to pitch downward and become level with the loading surface.
15
Hydraulic Power Unit: contains the electric motor driving the hydraulic pump, the oil tank, and the control valves.
16
Control Box: contains control buttons used to operate the lift.
17
Center point of maximum load:point up to which the maximum rated capacity of the liftgate is valid. Beyond that point, the
maximum safe working load diminishes according to the applicable load charts.

10
DHOLLANDIA
1
2
3
4, 5, 6
7
8
9
10
11
12
14
15
16
17
13
Figure 6.1

11
DHOLLANDIA
6.2 INSTALLATION PARAMETERS TERMINOLOGY
See [Figure 6.2] on next page for parts corresponding to numbers in this table
LARM
Length of the lift arms [= Lift ARM length]
VFH max
Max. height of vehicle floor (UNLOADED), applicable for the given arm length [= Vehicle Floor Height]
VFH
Actual height of vehicle floor (UNLOADED)
VFH min
Min. height of vehicle floor (FULLY LOADED)
CTH max
Max. height from underside of chassis to top of the vehicle floor, applicable for the given arm length [= Chassis Total Height]
CTH
Actual height from underside of chassis to top of the vehicle floor
MFT
Mounting height of lift frame under the vehicle: measured from the top of vehicle floor to the top of the lift frame main tube [=
Mounting height Floor to Tube of frame]
MTG
Mounting height of lift frame above the ground: measured from the top of the lift frame main tube to the ground [= Mounting
height Tube of lift frame to Ground]
MPG
Ground clearance under liftgate [= Mounting clearance Plates to Ground]
PD
[= Platform Depth]
LOF
Required mounting space to end of lift frame [= Lift Overhang to Frame]

12
DHOLLANDIA
Figure 6.2

13
DHOLLANDIA
See [Figure 6.3] on this page for parts corresponding to numbers in this table.
LAC
Width of the lift arms [= Lift Arm Center]
CHW
Vehicle chassis width [= CHassis Width]
BWO MIN
Min. body width with pump unit in premounted position [= Body Width Outside]
BCI
Width of the mid panel [= Body Cut Inside]
BCW
Width of the cut-outs for the lift arms and tilt cylinders [= Body Cut Width]
BLB
Available mounting space for rear truck lights on outside of the tilt cylinders [= Body Light Boxes]
BFT
Thickness of the rear cross member or sill of the vehicle bed [= Body Floor Thickness]
LFT
Max. thickness of the rear cross member or sill of the vehicle bed, in the maneuver zone BCW for the lift arms and tilt cylinders
[= Lift Floor Thickness]
Figure 6.3
BWO MIN
LAC
BCI
CHW
BCW
BFT/LFT
CTH MAX
BLB
MFT

14
DHOLLANDIA
6.3 GETTING STARTED
•OEM Vehicle manufacturers may have issued important instructions on various aspects of the liftgate installation, specific to the
brand and type of chassis, such as welding instructions (or prohibition to weld!); instructions on chassis drilling and bolt-on
connections to the chassis; recommendations on the use of hydraulic stabilizing legs; guidelines for the battery and ground cable
connections; fuses and other electrical interfaces; etc...
NOTICE
•The installer MUST verify and ensure compatibility between the liftgate and the vehicle.
•The installer MUST verify and ensure compliance with the installation instructions issued by the vehicle and body
manufacturer.
•Improper modifications to the vehicle chassis or body could cause serious mechanical failure of the vehicle. The installer MUST
ensure that modifications to the vehicle chassis and / or body will not adversely affect the structural integrity of the chassis and / or
body.
•In the event instructions of vehicle manufacturer conflict with the installation instructions issued by DHOLLANDIA (e.g. on fuse
ratings, etc.), contact your national DHOLLANDIA distributor for further assistance.
•In the event OEM instructions conflict with the installation instructions issued by DHOLLANDIA (e.g fuse ratings, etc.) contact
DHOLLANDIA US. See page 5 for contact info.
•Place vehicle on a flat even ground and chock the wheels so that it cannot move during the installation process. In case of a motor
vehicle, switch off the engine and engage the parking brake before starting.
•Verify the installation kit is complete, and that all parts needed to correctly fit the liftgate are present.
•Compare the voltage of the vehicle batteries with the voltage of the hydraulic pump unit of the liftgate.
•Compare the installation dimensions and maximum installation parameters indicated in the installation drawing with the actual
dimensions of the vehicle, to verify compliance. (See next chapter).
•Verify if the vehicle chassis and body are strong enough to support the load and moment created by the liftgate at maximum rated
capacity. Refer to the Body Builder Guidelines of the OEM vehicle manufacturer for details.
•Check the stability of the vehicle and the weight over the axles with the addition of a liftgate loaded to maximum capacity. The weights
indicated in the technical documentation and price list are theoretical and approximate and may vary from one liftgate installation to
another.
•Make sure that the body is accurately fitted to the vehicle chassis.
•Remove all objects that are mounted in the mounting space required by the liftgate (RUP, spare wheel carrier, pallet racks, tool
boxes, etc.). If necessary, consult with the OEM vehicle manufacturer for replacement solutions (e.g. special spare wheel carriers,
exhaust pipe modifications, etc.).
•Finish the liftgate in compliance with applicable road legislation of the country where the vehicle will be registered.
•When connecting hydraulic fittings, make sure that the connections are thoroughly clean, and that you don’t contaminate the hydraulic
oil.
•Grease all bearings and pins before putting the liftgate into service. It is recommended to grease all articulation bearings before
mounting the corresponding articulation pin.

15
DHOLLANDIA
•After installation, work through the pre-delivery inspection (PDI) checklist, verify all check points with due diligence. Make sure the
final inspection is signed off by an inspector who is not part of the installation team.
•Do not pressurize any liftgate functions (LIFT / LOWER) before the liftgate installation is fully finished.
•During installation and while testing, verify that the liftgate and its moving parts don’t interfere with, or cause damage to the vehicle
systems (e.g. to suspension, braking system, hydraulic and electrical circuits, etc.).
•Do not release the locking bolts of the auto-tilt brackets on the lift frame before the liftgate installation is fully finished [Figure 6.4].
6.4 INSTALLATION DIMENSIONS
•If an INSTALLATION DRAWING is available (via order confirmation), this will provide you with the critical installation dimensions that
should be observed. [see Figure 6.5]
M
Figure 6.4
Figure 6.5

16
DHOLLANDIA
Figure 6.7
•If no installation drawing is available, max. and min. installation parameters can be retrieved from TECHNICAL PRODUCT
SUMMARIES [Figure 6.6], or from the PRODUCT RANGE POCKET GUIDE [Figure 6.7];
•Compare the installation dimensions and maximum installation parameters indicated in above mentioned sources with the actual
dimensions of the vehicle, to verify compliance.
•Verify that the actual vehicle dimensions comply with the max. vehicle bed height VFH max, and with the min. / max. mounting heights
MFT.
•Determine the applicable fitting height MFTeither from the FITTING DRAWING supplied with the liftgate, or from the TECHNICAL
SUMMARY.
Figure 6.8
EX.
H
M
Figure 6.6
≠







17
DHOLLANDIA
•The fitting height, MFC, is measured from the top of the loading floor of the vehicle to the center of the lift arm articulation pin. Be sure
to follow these instructions as failure to do so could result in installation errors.
•As a general rule, in the absence of a FITTING DRAWING with a confirmed fitting height, this dimension can be calculated as follows:
Ex. For vehicle with 49¼” (1250mm) bed height:
•Fitting height MFT = (49¼” – 5”)/2 = 275
8"(555 mm)
•You might want to deviate from the initial mounting height MFT. Examples:
1. In order to increase the ground clearance MTG, you could choose to fit liftgate higher above ground
2. In case of short mounting space LOF / LOP, you could choose to fit liftgate lower to the ground
3. To comply with RUP regulations, you could choose to fit liftgate higher above or lower to the ground.
•When changing the fitting height, refer to the TECHNICAL SUMMARY of the liftgate in question and be sure to stay within the given
ranges of dimensions VFH, MFT, and MTG given for every lift arm.
•Also make sure that the new fitting situation complies with the compulsory bumper bar regulations. See [Figure 6.9] for an example
of the important fitting dimensions.
Figure 6.9
Dimensions table
inches
mm
LOS
77
1960
LOF
71½
1820
MFT
26
653
MTG
25
646
VFH
51
1300
mounting height MFT=
vehicle bed height VFH - 5.5” (140mm)
2
≥
≥

18
DHOLLANDIA
•For SIDE-MOUNTING on truck chassis, when changing the fitting height, MFT; ensure that the drill holes in the mounting brackets
for the aluminium sliding tubes still fall within the chassis [see Figure 6.10].
•Refer to the TECHNICAL SUMMARY of the liftgate for details on the correlation between the arm length, the fitting height and the
required overhang [see Figure 6.12].
•For any given platform depth, PD; the required overhang VARIABLE can be reduced by 4” (100mm) with the option (S245.S) on the
platform [see Figure 6.11].
•Refer to the TECHNICAL SUMMARY of the liftgate to define:
1. The minimum body width BWO.
2. The cut-out dimensions BCW, CHW, determining the size of the mounting plates for the vehicle rear lights and the slots for
the lift arms / cylinders of the lift. Or, the opposite way around, the dimensions indicating which arm width will suit a
predetermined rear body configuration. [see Figure 6.2]
•Adjust the rear side of the body accordingly. BCW and CHW depend on the arm width LAC. LFT depends on the fitting height MTG.
•The height of the rear cross member LFT varies also with the shape of the platform: standard platform hands or option (S245.S).
[see Figure 6.13]
Option S245.S
Figure 6.11
Figure 6.10
Figure 6.12
Figure 6.2
4”
4”

19
DHOLLANDIA
7TYPES OF CHASSIS AND FITTING METHODS
•Most slider liftgates are equipped with bolt-on sliding tubes (except
for the DH-SP and DH-SV which come with weld-on sliding tubes),
adapted to the type of chassis of the vehicle.
•The distinction between “side-mounting” and “under-mounting” can
be made by whether the tubes are being attached to a truck chassis,
or a trailer or semi-trailer chassis, respectively.
•1 in Figure 7.3 shows the tubes side-mounting to a truck chassis. 2
in Figure 7.3 illustrates under-mounting aluminium tubes to a trailer
chassis. Finally, 3 in Figure 7.3 shows under-mounting steel tubes to
a trailer chassis.
•The slider liftgates covered by this manual are all actuated in / out by
means of a hydraulic motor [see Figure 7.1 –7.2].
•The hydraulic motor does not require any fixation of the drive system
to the vehicle chassis. In comparison to a double acting retraction
cylinder, this motor allows:
1. To reduce fitting time
2. To reduce the required overhang
dimension
•The DH-S* liftgate range with a 1500-3000 kg capacity is comprised
of 2 generic frame types and slide plates:
1. Bolt-on slide plates, which can be moved side to side to
adjust their position to the width of the vehicle chassis.
[Figure 7.4]
2. Pre-mounted or integrated slide plates, which cannot
move side to side, but are configurable via their adjustable
mounting brackets. [Figure 7.5]
•Take this information into account when preparing the fitting work
of the liftgate.
Figure 7.1
Figure 7.2
Figure 7.3
Figure 7.4
Figure 7.5
❶
❷
❸