Diamond Coral WATERBAR+ User manual

USER MANUAL

Contents 02
Important Information
Technical Specifications
Component Identification
Details to be check before Installation
How to operate the Water Bar
Method to collect Hot/Warm Water
Cleaning
Power Supply
Tips for safe use
Troubleshooting
Service Hotlines / Email
繁體中文 内容
简体中文 內容
Page 03
Page 04
Page 05
Page 07
Page 08
Page 13
Page 14
Page 15
Page 17
Page 19
Page 23
第25 頁
第48 页

Important Information 03
WARNING!
This symbol is used whenever there is a risk of personal injury.
• This appliance must be installed, commissioned and serviced by
a qualified person in accordance with national and local regulations in
force in the country of installation..
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similar qualified person.
• Ensure that the plug/socket is accessible at all times.
• Strip plastic coating and clean the appliance before use.
• During operation parts may become hot - avoid accidental contact.
• Disconnect this appliance before servicing, maintenance or cleaning.
Caution!
This symbol is used to alert that the appliance may become
hot during operation.

Technical Specifications 04
Power Voltage
Rated Consuming Power
Product Size
Standby Power
Product Weight
Hot Water
Hot Water Yield
Warm Water
Warm Water Yield
Recommended environment
The temperature and water dispense level will be affected by the regional voltage or water storage temperature.
: 220V-240V / 50Hz
: 2200watt
: 338mm (L) x 160mm (W) x 377mm(H) Water Bar
: <2 watt
: 5kg
: ≥85°C
: Hot water 350-450cc/per min
: 45°C-55°C
: Warmwater > 450cc/per min
: 5°C-38°C

Component Identification 05
Front View
Power On Button/
Hot Water Unlock
Hot Water Button
Warm Water Button
Normal Water Button
Drip Tray Grid
Drip Tray

Component Identification 06
Power Cord
Filter Water Inlet
Rear cover release knob
(use proper tools insert into
the hole to release rear cover)
Rear view

Details to be check before Installation 07
• DO NOT place the device near any heat source and keep it out of direct sunlight.
This may cause colour changes or fire.
• Allow installation space.
To allow convenient installation for the unit, make sure to leave space around the unit
(at least 20 cm (8 in.) away from the wall)
• Do not place the device in the area with high moisture/humidity, dust or water splash.
It may cause a risk of fire or damage.
• Do not place device in the area with the temperature 0°C or below. Low temperature
conditions might cause a risk of failure of certain internal components and the malfunction
of the device.
• The device is for indoor use only

How to operate the Water Bar 08
1.0. First time installation - Cleaning the water tank
Please clean the water tank with a soft cloth.
1. Open the water tank cap.
2. Suggested to use a net sponge for
washing the water tank
3. Fill half of the tank with water.
4. Wash the surrounding with the
net sponge. Pour out water after
clean the surrounding.
Please repeat the step 3 and 4 for
2 times.
5. Close the water tank with cover.
Net Sponge

How to operate the Water Bar 09
2.0. How to install the unit?
1. Install this water tank adaptor,
firstly please ensure that there is a tube attached
together (as circle).
2. Fully insert the water tank adaptor into the adaptor guide hole
(as shown in the picture). Please ensure that the power cord
cable has connected properly at the bottom of water tank
adaptor.
This button will bounce
when the adaptor is fully
insert.

How to operate the Water Bar 10
3. Refill the water tank with
purified water filter.
4. Attach the water tank to the water tank adaptor.
Please ensure that the water tank has fully inserted to the
water tank sealing hole (as shown in the picture above).
Water Tank Sealing Hole