DIEBOLD NIXDORF BEETLE /XS User manual

BEETLE /XS
Operator Manual
01750332149A

Copyright © Diebold Nixdorf. Copyright protection is claimed for each revision listed in the document his-
tory, as of the date indicated. All Rights Reserved.
This document contains proprietary information of Diebold Nixdorf, Incorporated or its subsidiaries (col-
lectively “Diebold Nixdorf”) and may include information that is protected by copyright, trademark and
patent laws in the US, Germany, and globally. All rights, including rights created by patent grants or reg-
istration of a utility model or design, are reserved.
•No part of this document may be translated, reproduced, stored in a retrieval system, or trans-
mitted, in any form or by any means: electronic, mechanical, photocopying, recording, or oth-
erwise, without prior written permission from Diebold Nixdorf. Any violations of the foregoing
may give rise to a claim for damages.
•If the document pages state the information is confidential (or words of similar import), then
this document is intended solely for the use of the employees or other personnel of Diebold
Nixdorf unless expressly authorized in writing by Diebold Nixdorf. Other uses of this informa-
tion without the express written consent of Diebold Nixdorf are prohibited.
•This document should be treated as confidential material for security reasons. Any unautho-
rized disclosure or use of confidential material may violate the U.S. Theft of Trade Secrets
provisions of Section 1832 of Title 18 of the United States Code as well as comparable laws in
other jurisdictions throughout the world, and may be punishable by fine and imprisonment.
This document and the information contained herein are provided AS IS AND WITHOUT WAR-
RANTY. In no event shall Diebold Nixdorf or its suppliers be liable for any special, indirect, or
consequential damages of any nature resulting from the use of information in this manual. The in-
formation contained in this document is subject to change without notice. When using the document for
system implementation, please call your authorized Diebold Nixdorf sales or service representative for
any applicable changes.
Any trademarks, service marks, product names or company names not owned by Diebold Nixdorf, that
appear in this document are used for informational purposes only, and Diebold Nixdorf claims no rights
thereto, nor does such use indicate any affiliation with or any endorsement of Diebold Nixdorf or Diebold
Nixdorf products by the owners thereof.
Your use of this document and/or any of the information contained herein constitutes your agreement to
all of the terms stated on this page.
Copyright 2019 Diebold Nixdorf
01750332149A
ii

Table of contents
1Introduction ..................................................................................................................... 1-1
1.1 Further documentation...................................................................................................... 1-1
2Section-specific warning notes ..................................................................................... 2-1
3Delivery package............................................................................................................. 3-1
4ESD................................................................................................................................... 4-1
5Disengaging cables ........................................................................................................ 5-1
6Front view ........................................................................................................................ 6-1
6.1 On/Off button .................................................................................................................... 6-1
6.2 Light emitting diodes ......................................................................................................... 6-1
6.3 USB (Universal Serial Bus)-A, USB 2.0............................................................................ 6-1
7Inside view....................................................................................................................... 7-1
8Back panel ...................................................................................................................... 8-1
8.1 COM1-COM2 .................................................................................................................... 8-1
8.2 COM3*-COM4* ................................................................................................................. 8-1
8.3 Display 1 and Display 2 .................................................................................................... 8-1
8.4 3.5 mm jack bush (In/Out/microphone)............................................................................. 8-3
8.5 PoweredUSB .................................................................................................................... 8-3
8.6 Mini-DIN (KYBD, keyboard) .............................................................................................. 8-3
8.7 USB (Universal Serial Bus) A 2.0, 3.0 .............................................................................. 8-3
8.8 RJ45 (LAN) ....................................................................................................................... 8-4
9Setting up the device...................................................................................................... 9-1
9.1 Minimum distances ........................................................................................................... 9-1
9.2 Wall mounting ................................................................................................................... 9-2
9.2.1 Wall holders ...................................................................................................................... 9-2
9.2.2 Dimensions ....................................................................................................................... 9-3
9.2.3 Installation......................................................................................................................... 9-4
9.2.4 Wall holders mounted ....................................................................................................... 9-5
10 .......................................................................................................................................... 10-1
11 Removing the housing cover......................................................................................... 11-1
12 Battery change ................................................................................................................ 12-1
13 M.2 Module ...................................................................................................................... 13-1
14 System maintenance ...................................................................................................... 14-1
15 Technical Data................................................................................................................. 15-1
15.1 Interfaces .......................................................................................................................... 15-1
15.2 Total Current Consumption Interfaces .............................................................................. 15-2
15.3 Max. peripheral equipment current consumption.............................................................. 15-2
15.4 Power supply .................................................................................................................... 15-3
Copyright 2019 Diebold Nixdorf
01750332149A
iii

Table of contents
16 Manufacturer´s Certification .......................................................................................... 16-1
17 Recycling ......................................................................................................................... 17-1
Copyright 2019 Diebold Nixdorf
01750332149A
iv

1
1 Introduction
The BEETLE /XS is the ideal system platform for customers who desire maximum system availability
and lowest operating costs.
The fanless and closed system design and the use of innovative
M.2 memory technology ensures maximum reliability.
The dust-tight, closed housing protects the interior of the system against soiling and foreign objects.
Contemporary mobile Intel Quad Core processor technology and an energy-efficient power supply unit
ensure low current consumption and low heat build-up.
Despite its compact size, the system offers a multitude of standard PC and proven retail-specific inter-
faces.
1.1
1.1 Further documentation
Motherboard O1 POS https://www.dieboldnixdorf.com/de-de/customer-
service/documentation-services/pos-kiosk-systems-
peripherals/manual-downloads/pos-motherboards/
motherboards
Copyright 2019 Diebold Nixdorf
01750332149A
1-1

2
2 Section-specific warning notes
DANGER
This warning note describes a hazard with a high degree of risk which, if not avoided, will
result in death or grave bodily injury.
WARNING
This warning note describes a hazard with a medium degree of risk which, if not avoided,
could result in death or grave bodily injury.
CAUTION
This warning note describes a hazard with a low degree of risk which, if not avoided, could
result in slight or minor bodily injury.
NOTE
This note provides application tips and information that help prevent errors and material
damage.
Copyright 2019 Diebold Nixdorf
01750332149A
2-1

3
3 Delivery package
Unpack the parts and check whether they correspond to the parts listed on the delivery note.
If you should you detect any
• shipping damage or
• inconsistencies between package content and the bill of delivery or
• function defects,
please inform your contract partner or your Diebold Nixdorf sales outlet immediately. Please specify the
delivery note number, the delivery note item number and the serial number of the affected device when
doing so.
The Serial Number (S/N) can be found on the type label attached to the underside of the device.
Figure3-1: Type Plate
Please do not fail to check the function of the original device before making changes (e.g. by installing
an extension board). Only then may a functional deficiency be recognized as grounds for complaint.
We recommend that you keep the original packaging for any subsequent transport that may become
necessary (protection against jolts and impact).
Copyright 2019 Diebold Nixdorf
01750332149A
3-1

4
4 ESD
Sub-assemblies with ElectroStatic Discharge-sensitive components (ESD) can be marked
with this label.
When installing sub-assemblies or modules, please observe the following information that applies to all
sub-assemblies with ESD:
• Ensure that the device is disconnected from the power supply before you plug in, unplug or install
sub-assemblies with ESD.
• Always use anti-static equipment (anti-static mat with ground cable with integrated leakage resis-
tance of 1 Mohm, anti-static armband with connection to the mat, anti-statically equipped tools). The
anti-static mat must be connected to a suitable grounding point via the leakage resistance. Pull the
power plug before you plug in, unplug or install sub-assemblies with ESD.
• Place all sub-assemblies with ESD on a suitable anti-static base.
• Touch sub-assemblies with ESD only at their edges and do not touch any components.
• Do not touch any connector pins or conductor paths on an electrostatic-discharge-sensitive assem-
bly.
Copyright 2019 Diebold Nixdorf
01750332149A
4-1

5
5 Disengaging cables
Never disconnect cables by pulling them on the cable itself but always grip them instead on the connec-
tor housing provided for this purpose. To detach the cables, proceed as described below:
• Switch off all network and periphery device switches.
• Pull all power cables out of the contactor contact electrical sockets of the house installation.
• Pull all data communications cables out of the plug connections of the data networks.
• Disengage all cables at the devices.
The Mini-DIN plugs (with Diebold Nixdorf key-
boards) are equipped with a locking mechanism
against unintended disengagement. To disengage
this plug, pull the plastic sleeve away from the
socket. The interlock is released. The metal of the
plug is visible.
To disengage an RJ12 plug, press the tab below
the plug upwards.
Disengage the USB-A plug by pulling on the plug
housing.
Copyright 2019 Diebold Nixdorf
01750332149A
5-1

Disengaging cables
The electrically supplied USB plug is disengaged
by pressing on the spring marked with the arrow.
Interface connector (COM/DVI/VGA) with knurled
screw can be disengaged by hand.
Copyright 2019 Diebold Nixdorf
01750332149A
5-2

Disengaging cables
To loosen a RJ45 plug, press the tab above the
plug (see arrow) downwards.
Copyright 2019 Diebold Nixdorf
01750332149A
5-3

6
6 Front view
Figure6-1: Front view
1 On / Off button 2 Status LED 3 2 x USB 2.0
6.1
6.1 On/Off button
If the power supply unit is equipped with current, then the system is switched on by pressing the On/Off
button.
6.2
6.2 Light emitting diodes
The light emitting diodes at the front of the system are marked:
HDD/SSD Right LED flashes yellow Read or write access on HDD/SSD
POWER Left LED lights orange Standby operation (S4/S5)
Left LED lights green Device is switched on (S0)
Left LED flashes green Standby (S3)
6.3
6.3 USB (Universal Serial Bus)-A, USB 2.0
USB peripherals can be connected to these connections (USB-A), e.g. scanners, scales or magnetic
card readers.
CAUTION
Only devices and cables that are in accordance with the valid USB specifications are per-
mitted to be connected to the USB interfaces.
Copyright 2019 Diebold Nixdorf
01750332149A
6-1

7
7 Inside view
Figure7-1: Inside view
1 PoweredUSB Hub 4 RAM 7 Motherboard
2 DC/DC converter 5 Battery 8 Cooling element
3 Cooling element/processor 6 M.2 SATA 9 Front USB 2.0
Copyright 2019 Diebold Nixdorf
01750332149A
7-1

8
8 Back panel
8.1
8.1 COM1-COM2
Connect for example a scale with dedicated power supply to the . COM1-COM2 are designed as 9-pin
D-sub plugs. If you connect scales to the device which are not supplied by Diebold Nixdorf, then you
must acquire a license for the driver software!
NOTE
Take care to ensure that the plug is correctly inserted and screwed down,because other-
wise malfunctions could occur.
8.2
8.2 COM3*-COM4*
Scanner, customer or operator displays without dedicated power supplies are connected to these inter-
faces, depending on the existing configuration.
A 9-pin D sub-socket is used for this purpose.
NOTE
Take care to ensure that the plug for the peripheral devices is tightly screw-connected with
the socket, because otherwise malfunctions could occur. The power supply is provided
through this socket.
8.3
8.3 Display 1 and Display 2
This interface is used for connecting a high-resolution monitor to the BEETLE system. It can be used as
DVI-D or as PanelLink 2.0 interface. Here video signals with a maximum resolution of 1920×1200 pixels
can be transferred at 60 Hz.
PanelLink 2.0 is supported by specific DN-Displays and supplies video signals and power supply in only
one cable.
The display - interface of the BEETLE system has an RMT function. This function is utilized by actuating
the ON/OFF button on the screen. This function is available only if the BA8x/BA9x display has been con-
nected to a BEETLE system using a PLINK2™ interface cable. The mode of operation depends not only
on the settings of the BEETLE BIOS but also on the display settings. Details can be obtained from the
following table.
Copyright 2019 Diebold Nixdorf
01750332149A
8-1

Back panel
BEETLE
BIOS
Settings
BA8x/BA9x
Settings
BEETLE
System and
Display status
Reaction after pressing the display power-on button
RMT
enabled
RMT
enabled
OFF The system boots up. The display is switched on by the
system.
ON The system shuts down; the display switches off once
the system itself has been switched off completely.
RMT
disabled
OFF The system begins with the boot process; the display is
switched on by the system.
ON FW2.10 and higher: The system does not react; the
display switches off.
FW2.05: The system switches itself off; the display re-
mains switched on.
RMT
disabled
RMT
enabled
OFF The system does not react. The display remains off.
ON The system does not react; the display remains on.
RMT
disabled
OFF The system does not react; the display remains off.
ON The system does not react; the display remains off
The function (RMT) makes it possible for you to switch on the BEETLE system which is currently in
Standby or Hibernation mode. It is also possible to move the system from switched-on status into
Standby or Hibernation mode. The settings in the operating system determine which mode is active
thereby.
Copyright 2019 Diebold Nixdorf
01750332149A
8-2

Back panel
8.4
8.4 3.5 mm jack bush (In/Out/microphone)
Audio devices such as headphones, loudspeakers and microphones can be connected to these ports.
The three sockets are mechanically identical, although they differ in their function. The blue socket (Line
In) is an audio input. External audio sources can be connected here. The green socket (Line Out) is an
audio output. Headphones or loudspeakers can be connected here. Finally, a microphone can be con-
nected to the pink socket (Mic).
You can adjust the required volume through the software in the operating system or through the operat-
ing system itself (for example, the Windows operating system features a small loudspeaker symbol on
the taskbar which can be used to control the volume).
8.5
8.5 PoweredUSB
USB peripherals, whose energy demand is higher than the supply provided by the standard USBs, e.g.
printers, barcode scanners or displays, can be operated at PoweredUSB connections.
A mechanical coding prevents a USB 12 V plug from being accidentally plugged into a USB 24 V socket.
PoweredUSB ports can also be used as USB-A sockets.
8.6
8.6 Mini-DIN (KYBD, keyboard)
The device has a 6-pin Mini-DIN socket for the connection of a keyboard.
NOTE
Please ensure that the plug has a tight contact with the socket because otherwise it can
lead to malfunctions.
The power supply for the keyboard is provided through this socket. A special adapter cable is required
for the connection of a PC standard keyboard with a DIN plug. If required, contact your responsible
Wincor Nixdorf branch office.
The use of a Y adapter makes it possible to connect a PS/2 mouse in addition to the keyboard.
8.7
8.7 USB (Universal Serial Bus) A 2.0, 3.0
Various USB peripherals can be connected to these connections (USB-A), e.g. not only scanners, scales
or mice, but also dongles or even graphic cards or monitors. USB can provide the required power for de-
vices with little wattage such as phones or keyboards.
Copyright 2019 Diebold Nixdorf
01750332149A
8-3

Back panel
8.8
8.8 RJ45 (LAN)
The cable for the connection to a network (LAN) is plugged in here.
LEDs
Left LED Constant green Network connection established
Flashes green Data transfer
Right LED off 10 MBit
Constant green 100 MBit
Constant orange 1000 MBit
NOTE
Only use shielded LAN cables with the markings CAT5, CAT5e or CAT6. They provide a
higher protection against disturbances in the network.
Copyright 2019 Diebold Nixdorf
01750332149A
8-4

9
9 Setting up the device
9.1
9.1 Minimum distances
Please adhere to the listed minimum distances in front of the ventilation slots of the device.
Even if you want to install the device or mount it vertically, it is mandatory that you adhere to the mini-
mum distances listed in the illustration.
Figure9-1: Distances for free convection
Ensure constant aeration and ventilation. The direct ambient temperature of the system must not exceed
40°C (104°F).
Copyright 2019 Diebold Nixdorf
01750332149A
9-1

Setting up the device
9.2
9.2 Wall mounting
9.2.1
9.2.1 Wall holders
The Kit BEETLE /XS-Wandhalterung (01750330877) contains two angle bracket_XS (01750310537) and
4 screws:
Figure9-2: Wall holders with 4 screws
9.2.1.1
9.2.1.1 Dimensions
Figure9-3: Dimensions of wall holders
Copyright 2019 Diebold Nixdorf
01750332149A
9-2

Setting up the device
9.2.2
9.2.2 Dimensions
Copyright 2019 Diebold Nixdorf
01750332149A
9-3