DIEBOLD NIXDORF K-two User manual

K-two with card dispenser
Installation manual
Oktober 2019
01750339347A

Copyright
© Diebold Nixdorf
All rights, including rights of translation, reproduction by printing, copying or similar methods,
in part or in whole, are reserved.
Any violations give rise to a claim for damages. All rights reserved, particularly in relation to
the grant of a patent or the registration of a utility model. Subject to availability and technical
modifications.
All names of hardware and software products mentioned in this manual are trade names
and/or trademarks of their respective manufactures.

Contents
1Scope of document.........................................................................................1
2Further documentation...................................................................................1
3Symbols...........................................................................................................2
4Important Notes ..............................................................................................3
5Scope of delivery............................................................................................5
6Full view...........................................................................................................8
7Installation.......................................................................................................9
7.1 Safety Note.......................................................................................................9
7.2 Tools needed....................................................................................................9
8Dimensions ...................................................................................................29
9Service area...................................................................................................32
9.1 Block diagram.................................................................................................33
10 Recycling.......................................................................................................34

1
1 Scope of document
This manual contains important information about the installation requirements, connection
and maintenance of the device.
CAUTION
Installation and connection of this device may only be carried out by
authorized specialist personnel.
The safety instructions given in this document must be strictly followed when operating and
installing the device.
If you have any doubts or questions, please contact your Diebold Nixdorf contract partner at
any time.
2 Further documentation
K-two installation manual Diebold Nixdorf Intranet/Internet 01750299889
K-two user manual (D-EN) Diebold Nixdorf Intranet/Internet 01750312066
K-two service manual (D-EN) Diebold Nixdorf Intranet

2
3 Symbols
DANGER
This warning note describes a hazard with a high degree of risk, which, if not
avoided, will result in death or grave bodily injury.
WARNING
This warning note describes a
hazard with a medium degree of risk, which, if
not avoided, will result in death or grave bodily injury.
CAUTION
This warning note describes a hazard with a low degree of risk, which, if not
avoided, will result in death or grave bodily injury.
NOTICE
This note provides application tips and information that help prevent errors
and material damage.

3
4 Important Notes
Terminals supplied by Diebold Nixdorf comply with the respective safety regulations for data-
processing installations and information technology installations, including electrical office
equipment for use within an office environment.
WARNING
Whenever work of any kind is done on the device, as well as when data ca-
bles are plugged and unplugged, the device must be completely discon-
nected from the line voltage.
Terminals may only be installed and repaired by authorized technicians.
• Unauthorized opening of the housing or inexpert repairs can result not only in considera-
ble personal danger, but will also invalidate your warranty and liability protection.
• Always consult the enclosed documentation before doing any work with this terminal.
• If this terminal is brought from a cold environment into a heated place of business, con-
densation may occur. Before operation, the terminal must be completely dry. Therefore,
an acclimatization period of at least two hours must be adhered too.
• Always lay the supply leads and cables in such a way that they cannot be stepped on or
tripped over.
• Exchange damaged cables immediately.
• In order to completely disconnect the terminal from the power source use the separator in
the fuse box\building installation.
• Make sure that no objects (such as paper clips) can reach the interior of the terminal,
since electrical shocks or short-circuits could result.
• Ensure that the K-two receives adequate ventilation to avoid overheating.
• During an electrical storm, data cables should not be plugged in or being unplugged.
• Keep the terminal away from vibrations, dust, humidity and heat.
• Ensure that used parts are disposed of in an environmentally friendly manner.
• In case of an accident (such as a damaged housing, entry of liquids or foreign objects),
switch the terminal off and use the separator to completely remove the terminal from
power.

4
• The terminal and other information technology hardware should only be connected to
electrical supply networks with a separate protective earth wire (PE). This type of electri-
cal supply network is referred to as a TN-S network. Do not use PEN conductors. Also
follow the recommendations set forth in DIN VDE 0100 Part 540, Appendix C2 as well as
EN50174-2, §5.4.3 (www.DIN.de). This will help prevent malfunctions.
• National Electrical Code ANSI/NFPA 70-2005
• Always keep the ventilation slots free of obstruction to ensure adequate air circulation
and avoid overheating.
• Transport the terminal only in its original packaging (to protect it against knocks and
bumps).
• If a lithium battery is supplied with the terminal, ensure that the battery is replaced with an
equivalent type. Otherwise there is danger of explosion! Lithium batteries may only be re-
placed with identical types or other types recommended by the manufacturer.
• Batteries must be disposed of according to local regulations on the disposal of special
waste.

5
5 Scope of delivery
NOTICE
Check whether the serial number of the delivery units is the same as the
serial number of the K-two.
Delivery unit
K-two
K-two pillar (base plate (1) optional)
1

6
Delivery Unit
Card dispenser slot
Power supply
Cover
Power supply cable
Card dispenser
Covers for pillar
Housing card dispenser
Cable kit

7
Delivery Unit
Used screws/nuts
• Cylinder head screw M6x10 6x
• Self locking nut M4 2x
• Countersunk screw M5x10 4x
• Tapt. round head screw M4x8 6x
Rear housing card dispenser

8
6 Full view

9
7 Installation
7.1 Safety Note
CAUTION
Risk of crushing! Always wear safety gloves and safety shoes according
ISO 20345 with toe cap, closed heel area and energy absorbing heel area
while transporting or assembling the device.
USA: Safety shoes with class 1 toe cap according ASTM F 2412 and ANSI
Z41.1 in its current versions.
Canada: Protection CSA code 1Pxxx.
7.2 Tools needed
• Phillips screwdriver: PH2 mm
• Hexagon socket: 8; 5; 4 mm
• Torxs: TX20 mm
• Open-end wrench / Socket wrench for M4 (7) mm
• M3 (5,5 mm) for service only

10
Remove the plate from the top of the pillar (1).
Place the front card dispenser housing over the stand and place it at the bottom.
1

11
Then screw the screw plate back onto the stand (20Nm, 15 Lbf ft).
Grasp the K-two at the handles (see arrows)…..

12
…..set the K-two into place on the stand and fix it with 8x M6x16 counter sunk screws (see
also K-two installation manual).
Remove the handles.

13
Pull up the front card dispenser housing to the stop (see arrow).

14
Fix the card dispenser housing with 3 pcs. M6x10 at both sides (see arrows).

15
Push the cable harness through the opening to the K-two (see arrow) and connect it to the
PC box.
Lay the wiring harness at the following minimum distance from the printer. This will avoid
squeezing of the cables by the card reader in the door.
110 mm
[ 4,33 inch]
Guide through the cable here

16
The K-two kiosk comes with steel covers mounted instead of magnetic card reader and EFT.
These devices will be installed by the customer. Remove the cover and install the devices.
Install the ground strap of EFT the following way:
Card Reader UX300