Digicom Michelangelo LAN C User manual

http://www.digicom.it

Full rate 8Mbit/s ADSL support

G.lite 1Mbit/s ADSL support

Configuration utility

Software upgrade
User's Guide
rev. 1.0 del 10/2002
MICHELANGELO USB C

MICHELANGELO USB C Index
I
INDEX
PREFACE II
ENVIROMENTAL CONDITIONS II
CLEANING THE TERMINAL II
VIBRATIONS OR DROPPING II
WARNING: THIS IS A CLASS B PRODUCT. II
DECLARATION CE OF CONFORMITY II
1. GENERALITY 1.1
1.1. PRODUCT FEATURES 1.1
1.2. THE FRONT PANEL 1.2
1.3. REAR PANEL 1.2
2. HARDWARE INSTALLATION 2.1
3. SOFTWARE INSTALLATION
(WINDOWS® 98SE, ME, 2000 E XP) 3.1
4. VERIFY AND CHANGE THE CONFIGURATION 4.1
4.1. ADSL CONNECTION (PPPOA-PPPOE) 4.3
5. UNINSTALL 4.1

II
MICHELANGELO USB C Preface - Declaration CE of Conformity
PREFACE
All rights reserved; no part of this publication may be reproduced, stored in a retrieval system, or trasmitted in
any form or by any means, electronic, otherwise, without the priorwritten permission of Digicom S.p.A. The
contents of this booklet may be modified without prior permission. Every possible care has been taken in
testing and putting together all the documentation contained in this booklet, however Digicom can not take
any responsability brought by the use of this booklet.
The following installation rules should be respected in order to have the best working order of
the equipment and for the user’s safety.
ENVIROMENTAL CONDITIONS
ENVIROMENTAL TEMPERATURE RELATIVE HUMIDITY
from -5 to +45 ° Cfrom 20 to 80% n.c.
Rapid changes of temperature or humidity should be avoided (0,03 ° C/min).
This equipment, including cables, should be installed in an area free from:
 Dust, humidity, heat from direct sun light.
 Objects which irradiate heat.These could cause damage to the container or other problems.
 Objects which produce a strong electtromagnetic field (loudspeakers, etc.)
 Liquids or chemical corrosive substances.
CLEANING THE TERMINAL
Use a clean and soft cloth. Wet the cloth with water or natural detergent if it is necessary to
remove any stains. Never use chemical products such as petrol or solvents.
VIBRATIONS OR DROPPING
Caution against vibrations and dropping.
WARNING: THIS IS A CLASS B PRODUCT.
DECLARATION OF CONFORMITY
We, Digicom S.p.A. registered office at: via Volta 39 - 21010 Cardano al Campo (Varese -
Italy) declare under our sole responsability that the product:
Name: MICHELANGELO USB C Category: Information Technology Equipment, satisfies the
basic requirement of the below indicated Directive:
1999/5/CE of March 9 1999, R&TTE as having been designed in conformity with the
requirements of following Reference Standards:
- EN 55022
- EN 55024
- EN 61000-4-2 , EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6

MICHELANGELO USB C Generality
1.1
1. GENERALITY
Asymmetric Digital Subscriber Line
(ADSL) technology provides high-
speed data access over regular
phone lines. ADSL service is able to
co-exist on the same line with your
telephone service.
The ADSL has an unbalanced
connection speed.
It means that you have a connection
where data are received at the
maximum speed of 8Mbps and sent at the maximum speed of 1Mbps. The unbalance allows
to carry out connections with top performance in Internet access or remote access applications.
Asymmetric operation is ideal for home and small office use where files and information are
downloaded more frequently than uploaded.
ADSL modems employ ATM (Asynchronous Transfer Mode) framing. ATM is a protocol that
divides packets into small fixed sized cells for rapid transmission over high-speed networks.
Several different protocols are used over ATM. Michelangelo configuration depends on the
equipment used by your service provider:
 Point to Point Protocol Over ATM (PPPoA)
 Bridged/Routed Ethernet/IP over ATM (PPPoE)
1.1. PRODUCT FEATURES
 ADSL modem for PCI Bus
 Asymmetric data speed
 Downstream up to 8Mbps
 Upstream up to 1Mbps
 8 Mbps full rate ADSL support
 1.5 Mbps G.Lite ADSL support
 PC interface: PCI compliant with 2.2 specifications
 ADSL interface: RJ11 connector
 ADSL standards : ANSI T1.413, ITU G.992.1 (G.dmt) e ITUG.992.2 (G.lite)
 RFC Supported:
RFC1483 (Bridged/Routed Ethernet/IP over ATM)
RFC2516 (PPP over Ethernet)
RFC2364 (Point to Point Protocol Over ATM)

1.2
MICHELANGELO USB C Generality
 Windows® Plug&Play
 Flash upgradable
 CE mark
 Driver for Windows® 98SE/2000/ME/XP
1.2. THE FRONT PANEL
The following table explains the functions of the LEDs on the
Front Panel:
Name Color Status Meaning
Power Red Flashing Power on
Off Power off
Data Yellow Flashing Data is under transferring
Off Data is not under transferring
Link Green Flashing ADSL line is connected
Off Line link off
1.3. REAR PANEL

MICHELANGELO USB C Hardware Installation
2.1
2. HARDWARE INSTALLATION
Remove Michelangelo USB from its package
and check its integrity.
During the software installation, you will be
asked to connect the modem to your computer
USB port.
If you have any problems identifying
the USB socket on your Computer,
refer to the User’s Manual of your PC.
Connect the telephone cable to the
ADSL line.
USB

MICHELANGELO USB C Software Installation
3.1
3. SOFTWARE INSTALLATION
(WINDOWS® 98SE, ME, 2000 E XP)
For a right installation you have to perform the configuration utility. This will
automatically install the right driver with your provider configuration.
Before connecting the modem, you have to perform a Setup.exe file, present in the Driver\
Michelangelo USB C folder in the CdROM.
In the “Install the DSL Device” Windows click on the “Next>” button.

3.2
MICHELANGELO USB C Software Installation
You have to select the right configuration. Ask your Provider for the profile to be used.
Name Protocol Default
EoA Bridged IP over ATM LLCSNAP (RFC1483)
Routed IP over ATM LLCSNAP (RFC1483) 
Bridged IP over ATM VCMUX (RFC1483)
Routed IP over ATM VCMUX (RFC1483)
Classical IP over ATM (RFC1483)
PPPoA PPPoATM VCMUX (RFC2364) 
PPPoATM LLC (RFC2364)
PPPoE PPPoEthernet VCMUX (RFC2516)
PPPoEthernet LLCSNAP (RFC2516)
PPPoE PPPoATM VCMUX (RFC2364)
PPPoATM LLC (RFC2364)
PPPoE PPPoEthernet VCMUX (RFC2516)
PPPoEthernet LLCSNAP (RFC2516) 
The installation will install the default protocol. In order to change the protocol refer to chapter
4. VERIFY AND CHANGE THE CONFIGURATION.
Click on the “Next” button to continue the installation.

MICHELANGELO USB C Software Installation
3.3
The utility configuration will now install Michelangelo USB. This could take a few minutes.
Note: confirm with Continue Anyway the eventual informative Microsoft Windows®.
The software you are instaling has sucessfully passed digicom’s tests and the
compatibility with the supported Microsoft operating sytstems has been verified.

3.4
MICHELANGELO USB C Software Installation
Connect Michelangelo USB to your computer. The utility configuration will now configure and
test the driver . This could take a few minutes.
Click on “Finish” to confirm the installation.

MICHELANGELO USB C Verify and change the Configuration
4.1
4. VERIFY AND CHANGE THE CONFIGURATION
To check the installation use the “Michelangelo Control Panel” utility.
By pressing the “ALT” + “A” key, you’ll see more information.

4.2
MICHELANGELO USB C Verify and change the Configuration
With the Protocol Setup menu you can change the VPI, VCI parameters and Encapsulation
Mode.

MICHELANGELO USB C Verify and change the Configuration
4.3
4.1. ADSL CONNECTION (PPPOA-PPPOE)
You can use the remote access connection if your ISP uses the RFC2364 (PPPoA)
profiles or RFC2516 (PPPoE). You can use the Michelangelo USB ADSL utility (Shortcut on
the desktop) to carry out an easy connection. Just insert the User Name, the Password and
Click on Dial button.
If the User Name and Password fields are not present, you have to click on Properties button,
open the Options window and check the ”Prompt for name and password…”

MICHELANGELO USB C Uninstall
5.1
5. UNINSTALL
To uninstall the modem use the “Michelangelo USB ADSL” utility. You will find it in Start
Menu, Program and Michelangelo DSL.
Choose “Uninstall Michelangelo USB ADSL”, click on the “Next” button, then follow the
instructions.

MICHELANGELO USB C ADDENDUM
add.1
ADDENDUM al MANUALE OPERATIVO
MICHELANGELO USB C
rev. 1.0 del 10/2002
INSTALLAZIONE DRIVER
 Collegate Michelangelo USB al Computer.
 Windows® rileverà in automatico la presenza di un nuovo dispositivo.
 La procedura per installare i driver prevede di annullare l’installazione automatica, per poi
utilizzare l’utility d’installazione/configurazione.
 Per annullare l’installazione dovete premere “Annulla” nella schermata “Installazione guidata
nuovo hardware”.
 Per eseguire l’utility che Vi permetterà d’installare il modem, dovete andare nella cartella
Driver\Michelangelo USB C del CD-ROM ed eseguire il file Setup.exe.
 Procedete seguendo quanto descritto sul manuale.
ADDENDUM to the USER'S GUIDE
MICHELANGELO USB C
rev. 1.0 10/2002
SOFTWARE INSTALLATION
 Connect Michelangelo USB to the PC.
 Windows® will automatically detect a new hardware.
 Cancel the automatic driver installation and then perform the configuration utility.
 To cancel the automatic installation press “Cancel” in the window “Add New New Hardware
Wizard”.
 Double click the Setup.exe file, present in the Driver\Michelangelo USB C folder in the
CdROM.

ITALY
21010 Cardano al Campo VA
via A. Volta 39