Digicom Michelangelo Gateway User manual

http://www.digicom.it
ADSL MODEM
l
Full rate 8Mbit/s ADSL support
l
G.lite 1Mbit/s ADSL support
l
Configuration utility
l
Software upgrade
User's Guide
rev. 1.0 04/2000
MICHELANGELO USB

PMICHELANGELO USB Index
I
INDEX
PREFACE II
ENVIROMENTAL CONDITIONS II
CLEANING THE TERMINAL II
VIBRATIONS OR DROPPING II
DECLARATION CE OF CONFORMITY II
1. GENERALITY 1.1
1.2. PRODUCT FEATURES 1.1
2. HARDWARE INSTALLATION 2.1
3. SOFTWARE INSTALLATION 3.1
3.1. WINDOWS® 2000, ME, 98 3.1
3.2. CHANGE THE CONFIGURATION 3.5
3.3. CHECK THE INSTALLATION 3.7
3.4. CHANGE AND UPDATE THE DRIVERS 3.8
3.5. UNINSTALL 3.10
4. ADSL SERVICE 4.1

II
MICHELANGELO USB Preface - Declaration CE of Conformity
PREFACE
All rights reserved; no part of this publication may be reproduced, stored in a retrieval system, or trasmitted in
any form or by any means, electronic, otherwise, without the priorwritten permission of Digicom S.p.A. The
contents of this booklet may be modified without prior permission. Every possible care has been taken in
testing and putting together all the documentation contained in this booklet, however Digicom can not take
any responsability brought by the use of this booklet.
The following installation rules should be respected in order to have the best working order of
the equipment and for the user’s safety.
ENVIROMENTAL CONDITIONS
ENVIROMENTAL TEMPERATURE RELATIVE HUMIDITY
from -5 to +45 ° C from 20 to 80% n.c.
Rapid changes of temperature or humidity should be avoided (0,03 ° C/min).
This equipment, including cables, should be installed in an area free from:
l Dust, humidity, heat from direct sun light.
l Objectswhichirradiateheat.These couldcause damageto thecontainer orother problems.
l Objects which produce a strong electtromagnetic field (loudspeakers, etc.)
l Liquids or chemical corrosive substances.
CLEANING THE TERMINAL
Use a clean and soft cloth. Wet the cloth with water or natural detergent if it is necessary to
remove any stains. Never use chemical products such as petrol or solvents.
VIBRATIONS OR DROPPING
Caution against vibrations and dropping.
WARNING: THIS IS A CLASS B PRODUCT.
DECLARATION OF CONFORMITY
Digicom S.p.A. viaAlessandro Volta 39 21010 Cardano al Campo-Varese-
This product satisfies the basic requirements of the below indicated Directive:
l1999/5/CE 9th March 1999 about the telecommunications equipment
l89/336/CEE 3rd May 1989 about the electromagnetic compatibility
l73/23/CEE 19th February 1973 about the security

MICHELANGELO USB Generality
1.1
1. GENERALITY
AsymmetricDigitalSubscriber Line(ADSL) technologyprovides
high-speed dataaccessover regularphone lines.ADSLservice
is able to co-exist on the same line with your telephone service.
The ADSL has an unbalanced connection speed.
It means that you have a connection where data are received at
the maximum speed of 8Mbps and sent at the maximum speed
of 1Mbps. The unbalance allows to carry out connections with
top performance in Internet access or remote access
applications. Asymmetric operation is ideal for home and small
office use where files and information are downloaded more
frequently than uploaded.
ADSL modems employ ATM (Asynchronous Transfer Mode) framing. ATM is a protocol that
divides packets into small fixed sized cells for rapid transmission over high-speed networks.
Several different protocols are used over ATM. Michelangelo configuration depends on the
equipment used by your service provider:
l Point to Point Protocol Over ATM (PPPoA)
l Bridged/Routed Ethernet/IP overATM (PPPoE)
1.2. PRODUCT FEATURES
l ADSL modem for USB interface
l Asymmetric data speed
l Downstream up to 8Mbps
l Upstream up to 1Mbps
l 8 Mbps full rateADSL support
l 1.5 Mbps G.Lite ADSL support
l PC interface: USB
l ADSL interface: RJ11 connector
l ADSL standards : ANSI T1.413, ITU G.992.1 (G.dmt) e ITUG.992.2 (G.lite)
l Supported RFCs:
RFC1483 (Bridged/Routed Ethernet/IP overATM)
RFC1577 (Classical IP overATM)
RFC2364 (Point to Point Protocol OverATM)
l Windows® Plug&Play
l Flash upgradable
l CE mark
l Driver for Windows® ME/2000/98

MICHELANGELO USB Hardware Installation
2.1
2. HARDWARE INSTALLATION
l Remove the Michelangelo USB from its
package and check its integrity.
l Connect the USB cable to the USB socket
on your Computer.
If you have any problems identifying the
USB socket on your Computer, refer to the
User’s Manual of your PC.
l Connect the telephone cable to the ADSL
line.
l For the next steps refer to the Software
Installation section.
USB

MICHELANGELO USB Software Installation
3.1
3. SOFTWARE INSTALLATION
3.1. WINDOWS® 2000, ME, 98
At the next reboot, Windows® (98/98SE, ME, 2000) will automatically detect a new hardware
and start the driver installation process. Follow the instructions.
For a easer installation we suggest to cancel the driver installation and then perform the
configuration utility.
This will automatically install the right driver for your ISP configuration.
l Click on the “Cancel” button .
Software Installation
Select the Cd-rom drive, browse to the Driver folder and your specific Operating System
folder (D:\Driver\WinME\MichelangeloUSB) and double click the “Setup(.exe)” file.

3.2
MICHELANGELO USB Software Installation
l In the “Welcome” window click on the “Next>” button.
l Click on the “Yes” button to continue the installation.

MICHELANGELO USB Software Installation
3.3
You have to select a configuration.Ask your Provider for the profile to be used. The protocols
supported for each profile are summarized in the table below:
Profile RFC Protocol
Other Service Provider - -
Michelangelo USB WAN RFC 2364 PPPoATM NULL Encapsulation
RFC 2364 PPPoATM LLC Encapsulation
Michelangelo USB LAN RFC 1577 Classical IPoATM
RFC 1483 IPoATM Bridged LLC Encaapsulation
RFC 1483 IPoATM Bridged VC Encaapsulation
RFC 1483 IPoATM Routed LLC Encaapsulation
RFC 1483 IPoATM Routed VC Encaapsulation
Michelangelo USB ATM - -
l Select the right profile and click on the “Next>” button.

3.4
MICHELANGELO USB Software Installation
l Click on the “Next>” button to continue the installation.
l Click on the “Finish” button to finish the installation.

MICHELANGELO USB Software Installation
3.5
3.2. CHANGE THE CONFIGURATION
To configure the modem, from your PC desktop click Start - Programs - MichelangeloUSB
- Configure.
l Click on the “Settings” button.
Enter the * VPI, VCI, Encapsulation type and Modulation type from the “Communication
Settings” windows and click Next.

3.6
MICHELANGELO USB Software Installation
l Click on the “Apply>” button to continue the configuration.
* Use the values given by your ADSL Service Provider.

MICHELANGELO USB Software Installation
3.7
3.3. CHECK THE INSTALLATION
TheUSBADSLmodem controlpanel providesaquick andeasy wayto checktheperformance
of the modem and tha ADSL connection.
There are two methods to access the control panel:
l From the Start - Settings - Control Panel, double click the GlobeSpan DSL Modem.
l From the PC desktop, double click the icon in the System tray.

3.8
MICHELANGELO USB Software Installation
3.4. CHANGE AND UPDATE THE DRIVERS
To change the ADSLprofile or update the drivers click Start - Programs - MichelangeloUSB
- Configure.
l Click on the “Update” button.
l Browse to folder where the driver are located.

MICHELANGELO USB Software Installation
3.9
l Click on the “Finish” button.
Automatically the program for the installation will start. Refer to section "Software Installation"
for Further instruction.

3.10
MICHELANGELO USB Software Installation
3.5. UNINSTALL
Remove the USB ADSL Modem software drivers by performing the following steps.
From your PC desktop click Start – Programs – MichelangeloUSB – Configure.
l Click on the “Remove” button, then follow the instructions.

MICHELANGELO USB ADSL Service
4.1
4. ADSL SERVICE
There are two ways of performing an ADSL connection:
l Dial-Up Networking connection
l PPPoE utility connection
Remote access connection
You can use the remote access connection if your ISP uses the RFC2364 (Michelangelo USB
WAN).
In this case the Michelangelo USB will be installed as Michelangelo USB ADSLWAN and
you can choose it in Dial-Up Networking.
When you install the Michelangelo USB WAN Profile, a Dial-Up connection will be created
automatically.
Just double click on the new Dial-Up connection, type in the User Name and Password.
PPP over Ethernet (PPPoE)
You have to use a PPPoE utility if your ISP uses the RFC1483 (Michelangelo USB LAN)
profiles. The PPPoE utility is usually provided by your ISP.