Digisol DG-GR1010 User manual

V2.0
05-01-2021
GEPON ONU Router with
1 PON and 1 Giga Port
DG-GR1010

Copyright 2020 by DIGISOL SYSTEMS LTD. All rights reserved.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date.
Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form without
written consent from the company.
Copyright
Trademarks:
®
DIGISOL is a trademark of DIGISOL SYSTEMS LTD. All other trademarks
are the property of the respective manufacturers.

1:2 Application Chart
Figure 2
DG-GR1010 ONU meets telecom operators FTTO (office), FTTD (Desk),
FTTH(Home) broadband speed, SOHO broadband access, video
surveillance and other requirements and design an EPON Gigabit Ethernet
products. It is based on mature and stable, cost-effective EPON technology,
high reliability, easy management, configuration flexibility and good quality
of service (QoS) guarantees to meet the technical performance of the
module IEEE802.3ah.
1:1 Product Description
Overview
Figure 1 1GE

1:3 Technical Parameters
Technical item DG-GR1010
PON interface 1 EPON connector, SC single-mode/single-fiber,
downlink/uplink 1.25Gbps
Wavelength Tx:1310nm, Rx:1490nm
Optical interface SC connector
LAN interface 1*10/100/1000Mbps auto adaptive Ethernet interfaces
RJ-45 connector
LED 3 For Status of PON, LAN, SYS
Operating condition Temperature: -10°C ~ +55°C
Humidity: 10% 90% (non-condensing) ~
Storing condition Temperature: -30 60°C ~ °C
Humidity: 10% 90% (non-condensing) ~
Power supply DC 12V/0.5A
Power consumption ≤3W
Dimension 120mm×78mm×30mm (L×W×H)
Net weight 0.13Kg
1:4 Package Content
Contents Quantity
ONU 1 PCS
Power Adapter 1 PCS
User Manual 1 PCS

To avoid equipment damage caused by improper use and personal injury,
please observe the following precautions:
● Do not place the device near water or in damp places, in order to
prevent water or moisture from entering the device.
● Do not place the device in an unstable place, avoid falling damage to
equipment.
● Make sure that the supply voltage of the device matches the required
voltage value.
● Do not open the equipment chassis without permission.
● Unplug before cleaning the power plug; prohibit the use of liquid cleaning.
Installation Environment Requirements
ONU equipment must be installed in the interior, and to ensure the
following conditions:
● Confirmation at the ONU installation at sufficient space to facilitate
cooling machine.
● ONU suitable operating temperature of -10 ~55 , °C °C
humidity 10% to 90%.
Electromagnetic Environment
ONU equipment in use can be affected by external electromagnetic
interferences, such as radiation and conduction through the impact on the
device, this should note the following:
● Device workplace should avoid radio transmitters, radar stations, and
high-frequency interference from power equipment.
● Users cable typically require alignment indoors if outdoor lightning
traces measures should.
Equipment Installation
ONU product is a fixed configuration cassette equipment, site equipment
installation is relatively simple. Simply install the device on a specified place,
connecting the upstream fiber subscriber line connections, connect the
power cable. Actual operation is as follows:
2:1 Installation Requirements
Installation

1. Installed on the desktop
Place the machine on a clean bench, this installation is relatively simple,
you can observe the following operation:
● Ensure the smooth workbench.
● Around the device enough space for heat dissipation.
● Do not place objects on the device.
2. Mounted on the wall
● Observation ONU equipment chassis two cruciform recess, in
accordance with the position of the groove, installed two screws in the
wall.
● The original selected two mounting screws gently snap into recesses
aligned.
● Slowly let go, so that the device under the support of the screw
hanging on the wall.
2:2 Panel Lights
LED Mark Status Description
Registration REG
On and
Green in
colour
The device is registered to the PON system
Off / Red
in colour
Device is not registered to the PON system
Blink Device registration is incorrect
Fast Blink Port is sending or/and receiving data
Interface LINK/
ACT
On Port is connected properly (LINK)
Off Port connection exception or not connected
Blink Port is sending or/and receiving data (ACT)
System SYS
On / Off System is not running or fatal error
Blink Normal running

The following is the default device configuration information.
● Local (LAN access) Username: admin / Password: admin
● LAN port management IP address: 192.168.1.1/24
3:1 Default configuration
Web Management
EPON ONU provides simple Web management functions, including Device
Information, modify Lan Managemenet IP address, Loid and Password,
Configuration File backup and restore, firmware upgrade etc...
NOTE:
About More ONU Detail Configurations should be configured via CTC OAM
Protocols From OLT.
Figure 3 Web Login
3:2 Default configuration
Web login default username: admin, password: admin

Figure 4 Device Information
Device Info Menu displays the current device base informations, including
Hardware Version, Software Version, Boot Loader Version.
Note:
1. All the device information may be changed, the received device shall
prevail.

Figure 5 Modify Loid and Password
OID Menu displays the current device Loid and Password informations.
Loid: 0-24 bytes. Password: fixed 10 bytes.
Note:
1. Usually no need to modify the Version and Vendor Product Code
information, otherwise it may lead to ONU registration problems.
2. All the changes to take effect in the equipment after the restart.

Figure 6 Reboot/ Restore Default
Reboot: The operation to reboot the device.
Restore Default: The operation to restore the device to its factory
configuration.
Note:
1. Press RST button over 10 seconds, ONU can restore factory defaults
and reboot.
2. Press RST button quickly, ONU reboot.