Digisol DG-GR4010 User manual

V1.0
2018-05-25
GPON ONU Router with
1 PON and 1 Giga Port
DG-GR4010

Copyright 2018 by DIGISOL SYSTEMS LTD. All rights reserved.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date.
Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form without
written consent from the company.
Trademarks:
TM
DIGISOL is a trademark of DIGISOL SYSTEMS LTD. All other trademarks
are the property of the respective manufacturers.
Copyright

Figure 1 DG-GR4010
1:1 Product Description
Overview
DG-GR4010 ONU meets telecom operators FTTO (office), FTTD (Desk),
FTTH (Home) broadband speed, SOHO broadband access, video
surveillance and other requirements and design a GPON Gigabit Ethernet
products. The box is based on the mature Gigabit GPON technology, highly
reliable and easy to maintain, with guaranteed QOS for different service.
And it is fully compliant with technical regulations such as ITU-T G.984.x
1:2 Application Chart
Figure 2

1:3 Technical Parameters
Technical item DG-GR4010
PON interface 1GPON connector, SC single-mode/single-fiber,
uplink 1.25Gbps, downlink 2.5Gbps
Wavelength Tx1310nm,Rx 1490nm
Optical interface SC connector
LAN interface 1x 10/100/1000Mbps auto adaptive Ethernet interfaces
RJ-45 connector
LED 5, For Status of SYS, POWER, LOS, PON, LAN
Operating condition Temperature: -10°C ~ +55°C
Humidity: 10% 90% (non-condensing) ~
Storing condition Temperature: -30 60°C ~ °C
Humidity: 10% 90% (non-condensing) ~
Power supply DC 12V/0.5A
Power consumption ≤3W
Dimension 120mm×78mm×30mm (L×W×H)
Net weight 0.13Kg
1:4 Equipment List
Contents Quantity
ONU 1 PCS
Power Adapter 1 PCS
User Manual 1 PCS

To avoid equipment damage caused by improper use and personal injury,
please observe the following precautions:
● Do not place the device near water or in damp places, in order to
prevent water or moisture from entering the device.
● Do not place the device in an unstable place, avoid falling damage to
equipment.
● Make sure that the supply voltage of the device matches the required
voltage value.
● Do not open the equipment chassis without permission.
● Unplug before cleaning the power plug; prohibit the use of liquid cleaning.
Installation Environment Requirements
ONU equipment must be installed in the interior, and to ensure the
following conditions:
● Confirmation at the ONU installation at sufficient space to facilitate
cooling machine.
● ONU suitable operating temperature of - ~55 , 10°C °C
humidity 10% to 90%.
Electromagnetic Environment
ONU equipment in use can be affected by external electromagnetic
interferences, such as radiation and conduction through the impact on the
device, this should note the following:
● Device workplace should avoid radio transmitters, radar stations, and
high-frequency interference from power equipment.
● Users cable typically require alignment indoors if outdoor lightning
traces measures should.
Equipment Installation
ONU product is a fixed configuration cassette equipment, site equipment
installation is relatively simple. Simply install the device on a specified place,
connecting the upstream fiber subscriber line connections, connect the
power cable. Actual operation is as follows:
2:1 Installation Requirements
Installation

1. Installed on the desktop
Place the machine on a clean bench, this installation is relatively simple,
you can observe the following operation:
● Ensure the smooth workbench.
● Around the device enough space for heat dissipation.
● Do not place objects on the device.
2. Mounted on the wall
● The ONU equipment chasis has two cruciform recess, install two
screws in the wall in accordance to the position of the groove.
● The original selected two mounting screws gently snap into recesses
aligned.
● Slowly let go, so that the device under the support of the screw
hanging on the wall.
2:2 Panel Lights
LED Mark Status Description
Power Power
On The device is powered up
Off The device is powered down
Optical
signal loss LOS Blink Device does not receive optical signals
Off Device has received optical signal
Registration REG
On The device is registered to the PON system
Off Device is not registered to the PON system
Blink Device registration is incorrect
Fast Blink Port is sending or/and receiving data
Interface LINK/
ACT
On Port is connected properly (LINK)
Off Port connection exception or not connected
Blink Port is sending or/and receiving data (ACT)
System SYS
On / Off System is not running or fatal error
Blink Normal running

The following is the default device configuration information.
● Local (LAN access) Username: admin / Password: admin
● LAN port management IP address: 192.168.1.1/24
3:1 Default configuration
Web Management
GPON ONU provides simple Web management functions, including Device
Information, modify Lan Managemenet IP address, SN (Serial Number)
Loid, Password, Configuration File backup/upload/restore, firmware
upgrade etc...
NOTE:
About More ONU Detail Configurations should be configured via OMCI
protocols from OLT.
Figure 3 Web Login
3:2 Basic configuration
Web login default username: admin, password: admin

Figure 4 Device Information
Status Menu displays the current device base Information's. Including
Hardware Version, Boot Loader Version, PON Serial Number and
Password.
Note:
All the device information may be changed, the received device shall
prevail.

LOID/SN Menu displays the current device SN, Loid and Password
information's.
SN: Modify the device SN, fixed 12 bytes, 4 bytes for Vendor
manufacturers
Password: fixed 10 bytes. Loid: 0-24 bytes.
Note:
1. Usually no need to modify the Version and Vendor Product Code
information, otherwise it may lead to ONU registration problems.
2. All the changes to take effect in the equipment after the restart.
Figure 5 Modify Loid and Password

Figure 6 Reboot / Restore Default
Reboot: The operation to reboot the device.
Restore Default: The operation to restore the device to its factory
configuration.
Note:
1. Press RST button over 10 seconds, onu can restore factory defaults and
reboot.
2. Press RST button quickly, ONU reboot.