Digisol DG-FS1510HPE User manual

DG-FS1510HPE
8 PORT 10/100 MBPS WEB MANAGED POE SWITCH, 2
COMBO GBE PORTS
User Manual
V1.0
2015-05-11
As our products undergo continuous development the specifications are subject to change without prior notice
V1.0
2010-11-04
DG-FS1510HP
E
Layer 2 Fast Ethernet Web Managed Switch
AZTECA 1000 Web Managed Switch Series
V1.0
2011-01-24

DG-FS1510HPE User Manual
2
COPYRIGHT
Copyright 2015 by Smartlink Network Systems Ltd. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or
translated into any language or computer language, in any form or by any means,
electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of this company.
This company makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Any software described in
this manual is sold or licensed "as is". Should the programs prove defective
following their purchase, the buyer (and not this company, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair and any incidental
or consequential damages resulting from any defect in the software. Further, this
company reserves the right to revise this publication and to make changes from
time to time in the contents thereof without obligation to notify any person of such
revision or changes.
Trademarks:
DIGISOL™ is a trademark of Smartlink Network Systems Ltd. All other
trademarks are the property of the respective manufacturers.
Safety
This equipment is designed with the utmost care for the safety of those who install
and use it. However, special attention must be paid to the dangers of electric shock
and static electricity when working with electrical equipment. All guidelines of this
and of the computer manufacturer must therefore be allowed at all times to ensure
the safe use of the equipment.

DG-FS1510HPE User Manual
3
Index
1 Precautions......................................................................................................6
2 Overview.........................................................................................................7
2.1 Product Features..................................................................................7
3 Technical Specifications...................................................................................8
3.1 Environment Requirements..................................................................8
3.2 Power Interface....................................................................................8
3.3 Power Consumption.............................................................................8
3.4 Ethernet Interface ................................................................................8
3.5 Physical Characteristics .......................................................................9
4 Device Installation and Description................................................................ 10
4.1 Preparation Before Installation ........................................................... 10
4.1.1 Package Contents .................................................................. 10
4.1.2 Optional Accessories and Tools.............................................. 10
4.1.3 Choosing the Installation Location......................................... 10
4.1.3.1 Installing the DG-FS1510HPE on the Work Platform.. 10
4.1.3.2 Installing the DG-FS1510HPE on a Rack................... 11
4.2 Hardware Description........................................................................ 11
4.2.1 Front Panel ........................................................................... 11
4.2.2 Rear Panel............................................................................. 13
4.3 Electrical Setup.................................................................................. 13
4.3.1 Setting Up the Power Interface............................................... 13
4.3.2 Setting Up the Ethernet Interfaces .......................................... 13
5 Device Startup............................................................................................... 14
5.1 Check Before Power-On .................................................................... 14
5.2 Powering On the Device .................................................................... 14
6 Device Upgrade............................................................................................. 14
7 Web Configuration and Management.............................................................. 15
7.1 Preparation Before Login................................................................... 15
7.2 Logging In to the Switch.................................................................... 16
7.3 System Management.......................................................................... 17
7.3.1 Authentication Configuration ................................................. 18
7.3.2 System IP Configuration......................................................... 19
7.3.3 System Status......................................................................... 20

DG-FS1510HPE User Manual
4
7.3.4 Loading Default Settings........................................................ 20
7.3.5 Firmware Update................................................................... 21
7.3.6 Reboot the Device.................................................................. 21
7.4 POE.................................................................................................. 22
7.4.1 PoE Status............................................................................. 22
7.4.2 PoE Setting............................................................................ 23
7.4.3 PoE Power Delay .................................................................. 24
7.4.4 PoE Scheduling...................................................................... 25
7.4.5 NTP Setting ........................................................................... 25
7.5 Port Management............................................................................... 26
7.5.1 Port Configuration................................................................. 26
7.5.2 Port Mirroring....................................................................... 27
7.5.3 Bandwidth Control................................................................. 28
7.5.4 Broadcast Storm Control........................................................ 29
7.6 VLAN Setting ................................................................................... 29
7.6.1 VLAN Mode........................................................................... 30
7.6.1.1 VLAN Based on Port.................................................. 30
7.6.2 VLAN Member....................................................................... 30
7.6.2.1 VLAN Based on Port.................................................. 30
7.6.2.2 VLAN Based on Tag ................................................... 31
7.6.3 Multi to 1 Setting Configuration............................................. 33
7.7 Per Port Counter................................................................................ 34
7.8 QoS Configuration............................................................................. 35
7.8.1 Priority Mode........................................................................ 36
7.8.2 Class of Service Configuration - 1.......................................... 37
7.8.3 Class of Service Configuration - 2.......................................... 38
7.9 Security............................................................................................. 40
7.9.1 MAC Address Binding............................................................ 40
7.9.2 TCP/UDP Filter..................................................................... 41
7.10 Spanning Tree.................................................................................. 42
7.10.1 STP Bridge Settings ............................................................. 43
7.10.2 STP Port Settings................................................................. 45
7.10.3 Loopback Detection:............................................................ 47
7.11 Trunking.......................................................................................... 49
7.12 DHCP RelayAgent.......................................................................... 51

DG-FS1510HPE User Manual
5
7.12.1 DHCP RelayAgent.............................................................. 51
7.12.2 Relay Server........................................................................ 52
7.12.3 VLAN MAP Relay Agent....................................................... 52
7.13 Configuration Backup and Recovery ................................................ 53
7.14 Miscellaneous Configuration............................................................ 54
7.15 SNMP Settings................................................................................ 55
7.16 Logout ............................................................................................ 56
8 Troubleshooting............................................................................................. 56
9 Glossary........................................................................................................ 57

DG-FS1510HPE User Manual
6
1 Precautions
Power supply sockets with too heavy load or broken cables and plugs
may cause electric shock or fire. Users should check the power supply
wires and cables regularly. If there is any breakage, please replace the
cable at once.
Do not open the case of the device, especially during device power-on.
The device should be installed at position with good ventilation and
without high temperature or direct sunshine, so as to avoid faults of the
device and its corresponding components due to overheat.
Do not put this device close to a damp or watery place. Do not spill
any fluid on this device.
Keep proper space for heat dissipation, to avoid any damage to the
device caused by overheating. The holes on the shell are designed for
heat dissipation, to ensure that the device works normally. Do not
cover the heat dissipation holes.
Keep the power plug clean and dry, if abnormal phenomenon occurs,
such as smoke, abnormal sound, abnormal smell, switch off the power.

DG-FS1510HPE User Manual
7
2 Overview
The DG-FS1510HPE is an intelligent Layer 2 Ethernet switch. It provides 8 10M/100M
self-adaptive Ethernet ports and 2 gigabit combo ports. The combo ports can be flexibly
connected to gigabit copper cable or backbone fiber. You can select 1000BASE-LX,
1000BASE-SX or 1000BASE-T interface according to the transmission distance. The
DG-FS1510HPE supports VLAN classification,DHCP, port counter, port trunking and
QoS. You can configure the device easily through web interface.
2.1 Product Features
8 10M/100M self-adaptive FE ports and 2 10M/100M/1000M self-adaptive GE
ports. 2 SFP slots are shared with GE ports. You can connect the switch to other
switches through copper cable or fiber.
Manage the switch through web page. Network administrator can monitor and
configure the switch through any Ethernet port.
Supports the following standards: IEEE802.3at and IEEE802.3af standard
VLAN: Supports up to 32 Tag VLANs and up to 26 Port Based VLANs.
Supports 4K MAC addresses.
Other functions: CoS, broadcast storm control, port management, bandwidth
control, spanning tree protocol and simple network management.

DG-FS1510HPE User Manual
8
3 Technical Specifications
3.1 Environment Requirements
The whole device can survive in a wide range of operating temperature and can work
normally and stably in tough environment.
Operating temperature: 0˚C—50˚C
Storage temperature: -40˚C—70˚C
Relative humidity: 10%—90% RH (non-condensing)
3.2 Power Interface
Power input: 100V AC ~240V AC, 50/60Hz
3.3 Power Consumption
Whole device consumption: < 180 W
3.4 Ethernet Interface
Standard: IEEE802.3at and IEEE802.3af.
Transmission rate: Port 1 ~ Port 8 are 10 M/100 M self-adaptive.
Port 9 ~ Port 10 are 10 M/100 M/1000 M self-adaptive.
Working mode: full duplex, half duplex, self-adaptive.
Port type: 8 x 10/100Base-TX self-adaptive Ethernet ports. 2 x SFP fiber
ports. They are shared with 10/100/1000Base-TX self-adaptive Ethernet
ports.
Transmission distance: < 100m, Cat. 3/5 UTP. The transmission distance of
SFP port is determined by optical module.
Auto-MDI/MDI-X. Automatically distinguish crossover cable from straight
through cable.

DG-FS1510HPE User Manual
9
3.5 Physical Characteristics
Dimensions: 330(W) x 44(H) x 230(D) mm
Net Weight: 2.5 kgs

DG-FS1510HPE User Manual
10
4 Device Installation and Description
4.1 Preparation Before Installation
4.1.1 Package Contents
DG-FS1510HPE Fast Ethernet Switch
Power Cord
Bracket Mounting Kit containing two brackets and six screws for attaching
the brackets to the switch
CD containing User Manual
Four adhesive foot pads
4.1.2 Optional Accessories and Tools
Screwdriver
ESD straps
Ethernet crimping pliers, crystal heads
Ethernet (either crossover or straight through) cable
4.1.3 Choosing the Installation Location
The DG-FS1510HPE can be installed in either of the following ways as required:
On the work platform
On a rack
4.1.3.1 Installing the DG-FS1510HPE on the Work Platform
The common way is to install the DG-FS1510HPE on a clean work platform. Pay attention
to the following precautions:
Ensure that the work platform is flat and stable.
Ensure good ventilation of air ports on both sides of the device.
Do not put heavy objects on the device.

DG-FS1510HPE User Manual
11
4.1.3.2 Installing the DG-FS1510HPE on a Rack
Before installing the DG-FS1510HPE on a rack, you need to install the provided L-
Clamps on both sides of the DG-FS1510HPE.
4.2 Hardware Description
4.2.1 Front Panel
The following table describes the interfaces of the DG-FS1510HPE.
Interface
/Button
Description
Ports 1~8 8 x RJ-45 Ethernet interfaces, 10 M/100 M self-adaptive.
Ports 9, 10
Two groups of fiber-copper combo ports. The copper ports are 10 M/100
M/1000 M self-adaptive Ethernet ports and the fiber ports are SFP optical
module ports. If the combo ports are preferred to serve as fiber ports, that is,
if the ports connect to a fiber port, the copper port is disabled.
Reset
Keep the device powered on and push a paper clip into the hole. Press down
the button for about 5 seconds. The system restores the factory default
settings.

DG-FS1510HPE User Manual
12
The following table describes the LED indicators of the DG-FS1510HPE.
Interface/Button
Status/Color
Description
PWR
Green (ON)
Power ON.
OFF
Power OFF.
Ports (1-8)
(Link/Activity LED)
Amber (OFF)
Port disconnected or link fail.
ON
Port Connected.
Blinking
Sending or receiving data.
Ports (1-8) (PoE
LED)
Green (OFF)
PoE power OFF.
ON
PoE power ON.
10/100/1000
Copper ports LED’s
OFF
Port disconnected or link fail.
Green (ON)
1000Mbps connected.
Amber (ON)
10/100 Mbps connected.
BLinking
Sending or receiving data.
SFP Ports LED’s
OFF
Port disconnected or link fail.
Green (ON)
1000FX connected.
Blinking
Sending or receiving data.

DG-FS1510HPE User Manual
13
4.2.2 Rear Panel
Interface
Description
100-240VAC 50/60Hz
The power interface.
The power input is 100 V ~ 240 V AC, 50 Hz ~ 60Hz.
4.3 Electrical Setup
4.3.1 Setting Up the Power Interface
After placing the DG-FS1510HPE to a flat and stable surface, insert the supplied power
cord to the power socket, and connect the other end of the cable to the power interface of
DG-FS1510HPE.
4.3.2 Setting Up the Ethernet Interfaces
The DG-FS1510HPE provides 10 Ethernet service interfaces of standard RJ45 connectors.
You can use either the crossover or straight through cable to connect an interface.
Note:
To ensure good quality of the data signal, the length of the network cable
connected to the Ethernet interface should be shorter than 100m.

DG-FS1510HPE User Manual
14
5 Device Startup
5.1 Check Before Power-On
Before powering on the device, check the following:
Whether the voltage of the power supply is consistent with the power
requirement of the device.
Whether the power cord is correctly connected.
Whether the device is correctly connected to the ground on the rear side.
5.2 Powering On the Device
After connecting the power cable, turn on the power switch. When the Power indicator
turns on, the system starts to initialize. When other indicators blink three times and the
Power indicator is always on in green, the switch works normally.
6 Device Upgrade
You can upgrade the software through any Ethernet port for DG-FS1510HPE. After
software upgrade is complete, the system reboots automatically.

DG-FS1510HPE User Manual
15
7 Web Configuration and Management
The system does not support the CLI and telnet management. It supports the web
management only. This section describes the web configuration and management.
7.1 Preparation Before Login
Before accessing the switch, ensure the communication between PC and switch is normal.
Check the communication as follows.
1. Set the IP address of the PC in the range 192.168.2.X (2~254)
2. The subnet mask to 255.255.255.0.
3. Enter arp -d or arp -d 192.168.2.1 in the DOS window. See the following figure.
1. Ping the maintenance IP address (192.168.2.1 by default) of the switch. See the
following figure.

DG-FS1510HPE User Manual
16
If the PC can read the MAC address of the switch and can ping through the maintenance IP
address of the switch, that means the communication of the PC and the switch is normal.
7.2 Logging In to the Switch
1. Open the web browser, and type the default IP address of switch in the address bar
as ‗http: //192.168.2.1‘.
2. Enter the ID and the password. The default ID is admin and password is system.
3. Click OK to log in.

DG-FS1510HPE User Manual
17
After logging in to the switch successfully, the following page appears.
7.3 System Management
Choose Administrator, and the sub-menus of Administrator are shown as below.

DG-FS1510HPE User Manual
18
7.3.1 Authentication Configuration
Choose Administrator > Authentication Configuration, and the following page appears.
Read the Note in the page, and change the user name and password. After proper
configuration, click Update to apply the settings and then Reboot the device for the
changes to take effect.

DG-FS1510HPE User Manual
19
7.3.2 System IP Configuration
Choose Administrator > System IP Configuration, and the following page appears. In this
page, you can set the maintenance IP address of the switch, subnet mask and gateway. After
proper configuration, click Update to apply the settings and then Reboot the device for the
changes to take effect.

DG-FS1510HPE User Manual
20
7.3.3 System Status
Choose Administrator > System Status, and the following page appears. In this page,
you can view the MAC address, Number of ports, Comment,system version and idle time
security.
7.3.4 Loading Default Settings
Choose Administrator > Load default setting and the following page appears. In this
page, click Load to load the default settings that do not include IP address, user name and
password.