Digisol DG-WA1102NPLV2 User manual

DG-WA1102NPLV2 User Manual
1
DG-WA1102NPLV2
DIGISOL 2.4GHZ OUTDOOR ACCESS POINT
User Manual
V1.0
2017-01-30
As our products undergo continuous development the specifications are subject to change without prior
notice

DG-WA1102NPLV2 User Manual
2
COPYRIGHT
Copyright 2017 by DIGISOL SYSTEMS LTD. All rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without the prior written permission of this company.
This company makes no representations or warranties, either expressed or implied, with respect
to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any
particular purpose. Any software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not this company, its
distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any
incidental or consequential damages resulting from any defect in the software. Further, this
company reserves the right to revise this publication and to make changes from time to time in
the contents thereof without obligation to notify any person of such revision or changes.
Trademarks:
DIGISOL™ is a trademark of DIGISOL SYSTEMS LTD. All other trademarks are the property of
the respective manufacturers.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity
when working with electrical equipment. All guidelines of this and of the computer manufacturer
must therefore be allowed at all times to ensure the safe use of the equipment.

DG-WA1102NPLV2 User Manual
3
INDEX
1PRODUCT INFORMATION.................................................................................................................... 4
1.1 HARDWARE INSTALLATION .......................................................4
1ST:HOW TO CONNECT AND CHARGE THE AP ....................................................4
2ND:AP START AND LOG IN ...............................................................5
3RD:WEB GUI INTERFACE SETTING: .........................................................9
4TH SHARE INTERNET AND OBTAIN IP ADDRESS AUTOMATICALLY ......................................28
2TROUBLE SHOOTING: ........................................................................................................................ 29

DG-WA1102NPLV2 User Manual
4
1Product Information
Thank you for purchasing this Outdoor AP DG-WA1102NPLV2. This manual will instruct you how
to configure and manage this AP, enable you to use it in a perfect status. After installing this AP,
you will be able to enjoy surfing freely.
Please check the Package Contents before you use it:
DG-WA1102NPLV2
POE Adapter
Metal strap*1
Patch Cord
Installation Guide CD
1.1 Hardware installation
1St: How to connect and charge the AP
Interface Description
Fig 1 Interfaces
Item
Description
Reset
Press it for 10-15 seconds, the AP will restore to factory default.
WAN
Connect with internet cable, in Wi-Fi Repeater, bridge, WISP operation mode, it change
to LAN port.
LAN
Connect the AP with computer by LAN cable.
DC
For Power supply, the DC’s electronic standard is 12V/24V.

DG-WA1102NPLV2 User Manual
5
POE: This equipment can be powered over Ethernet, Connect AP’s WAN/LAN Port with
PoE adapter’s POE port by LAN Cable (AP’s LAN port and WAN port support the
12V/24V PoE.)
Please refer to fig 2 for PoE Power and AP configuration
Fig 2 Diagram of PoE Power and AP configuration
2nd: AP Start and Log in
1) Power the AP as shown in fig 2.
2) Set a fixed IP address for this computer: The default operation mode of this outdoor AP is
Wireless AP, end users should set an IP address for the computer, then you can access the
Outdoor AP’s IP: Set the computer’s IP address as 192.168.1.X (X is number between
1-252), make it same as AP’s network segment, then set Subnet mask as 255.255.255.0,
Default gateway leave it blank, then click OK.
A.: Please follow fig 3 and fig 4 for wired configuration.
Attention
Please make sure ourAP is working with included Power adapter
or PoE adapter, and under right connection way, or the device
will be damaged.
DG-WA1102NPL
DG-WA1102NPLV2

DG-WA1102NPLV2 User Manual
6
:
Fig 3 Configure the computer’s IP address (by wired)
Fig 4 Configure the computer’s IP (by wired)
B. Please follow fig 5 to configure the computer’s IP address wirelessly.

DG-WA1102NPLV2 User Manual
7
Fig 5 Configure the computer’s IP Address wirelessly
If you want to connect our AP wirelessly after IP address configuration, please right click Wireless
networking Connection, then View Available Wireless Networks. The default SSID is
DG-WA1102NPLV2. Click Refresh network list, double click the correct SSID and input the
passwords, if you have, then connect. Please refer to fig 6 and fig 7
Fig 6 AP Wireless Connection

DG-WA1102NPLV2 User Manual
8
Fig 7 AP Wireless Connection
Indicator
If your computer has built in 802.11b/g/n wireless adapter, but can’t search the
available wireless networking after refreshing, please contact the computer supplier or
after-sale department after going through the following points:
Right click My Network Places, select Properties, appear Local Area Connection or
Other Connection, No Wireless Network Connection
There is Wireless Network Connection in My Network Places, Show General and
Advanced after right click Wireless Network Connection and select Properties, but no
Wireless Network Configuration in Window

DG-WA1102NPLV2 User Manual
9
Log in the AP: Open your web browser, type in 192.168.1.200 in the address bar, enter admin in
white blank bar, then login.
Fig 8 Log in
3rd: WEB GUI interface Setting:
1) Status
After login, fig 9 Device Status will be shown:
This page, will show the outdoor AP’s default operation mode, channel, connection status, CPU
usage, Wireless settings, LAN Setting, AP’s Location, AP’s hardware/firmware version.
Fig 9 Status

DG-WA1102NPLV2 User Manual
10
In this Outdoor AP, the default operation mode isAP mode.
Then in 2.4G Wireless Setting, GUI configuration page will be as shown below:
User can configure the SSID, password, band width, channel here, thenApply to finish.
Fig 10 Wireless Setting
LAN Setting to configure the DHCP or Fix IP for local LAN.
Fig 11 LAN Setting

DG-WA1102NPLV2 User Manual
11
Fig 12 AP Position setting
2) Wizard Configuration:
Click Wizard in Status page, will pop up following page to configure the operation mode:
There are four operation modes of this ceiling wireless AP, and there are explanations for each
operation mode for better application.
Fig 13 Operation modes

DG-WA1102NPLV2 User Manual
12
I Gateway Mode:
Click Gateway mode, the following pictures will pop up:
Please choose the right WAN setting mode, then click next to continue.
Fig 14. WAN setting in Gateway Mode
Fig 15 Wireless Setting in Gateway Mode
When you click on Next, then will complete the Gateway mode setting and show the following

DG-WA1102NPLV2 User Manual
13
picture:
Fig 16 Complete the setting in Gateway Mode
When you return to Status, the page as shown below appears:
Fig 17 Status in Gateway Mode
II Wi-Fi Repeater mode
Click Wi-Fi Repeater operation mode in Wizard, then following page will pop up, and
choose the right SSID to bridge, then click next to finish it.

DG-WA1102NPLV2 User Manual
14
Fig 18 Repeater Mode
Click Return button, will go back to Status, shows Repeater mode data, shows fail or success,
and user can configure this data in this page if required.

DG-WA1102NPLV2 User Manual
15
Fig 19 Status in Repeater Mode
Please note, in Wi-Fi Repeater operation mode, the wireless is disabled by default, will not
broadcast the wireless SSID.
If you need to enable SSID, please do based on following picture:
Please note, when you click on wireless relay settings, will go back to fig 18 wi-fi repeater setting
directly.
III WISP Operation mode:
Click WISP operation mode in Wizard, then will pop up the configure page, please set the WISP
operation mode based on the steps shown in picture:

DG-WA1102NPLV2 User Manual
16
Fig 20 WISP Mode
Configure the right WAN setting in WISP operation mode, then next to restart the outdoor AP.
Fig 21 WAN setting in WISP mode
Then complete and back to status, will show the connection fail or success, then can configure

DG-WA1102NPLV2 User Manual
17
the data based on request:
Fig 22 Status in WISP mode
Remark: When you click on WAN setting the screen will pop up as shown in the following picture:
Fig 23 WAN setting in WISP mode
IV AP Operation mode:
Set the wireless data, AP Location info as required, then click next to continue and enter into LAN
setting.
After LAN setting, complete the AP mode configuration and back to Status:

DG-WA1102NPLV2 User Manual
18
Fig 24 Wireless setting in AP Mode
In this part, there is WirelessAnalyzer, to analyse the Wireless AP/ Router’s channel to avoid wi-fi
interface. Picture as shown in fig 25.
Fig 25 Wi-Fi Channel analysis

DG-WA1102NPLV2 User Manual
19
Fig 26 LAN Setting in AP Mode
Fig 27 Status in AP Mode
V WDS operation mode
In WDS setting two AP’s work in WDS operation mode:
A. Connect with WDS1 device and enter into the GUI page, Click Wizard and Choose SUPER
WDS mode, input the SSID, Band Width, Channel as you like, then click next to finish.
For example, the SSID is Wireless 2.4G-test-02.

DG-WA1102NPLV2 User Manual
20
B. Enter into WDS 2 device’s GUI page, click Wizard, then choose super WDS function.
In this page, click scan AP to choose WDS 1’s SSID.
In this page, can set WDS 2 device’s SSID as Wireless 2.4G-Test-01.
C. Click next to finish, then WDS2 will work with WDS1.