Digisol DG-WM6305SIE2 User manual

1
DG-WM6305SIE2
User Manual
V1.0
2018-03-13
As our products undergo continuous development the specifications are subject to change without prior notice.

DG-WM6305SIE2 User Manual
2
COPYRIGHT
Copyright 2017 by Digisol Systems Ltd. All rights reserved.
Company has an ongoing policy of upgrading its products and it may be possible
that information in this document is not up-to-date.
Please check with your local distributors for latest information. No part of this
document can be copied or reproduced in any form without written consent from
the company.
TRADEMARK
DIGISOL TM is a trademark of Digisol Systems Ltd. All other trademarks are the
property of the respective manufacturers.

DG-WM6305SIE2 User Manual
3
INDEX
1. Hardware and Operation mode Instruction……………………………………….4
1.1. LED Indicator………………………………………………………………...4
1.2. AP Router Interface…………………………………………………………4
1.3. Power Supply………………………………………………………………..5
1.3.1. PoE Adapter Power Supply…………………………………………..5
1.3.2. PoE Switch Power Supply…………………………………………….5
1.4. AP Router Installation……………………………………………………….7
2. Connect Wireless AP Router with PC………………………………………………8
3. Login………………………………………………………………………………..9
4. WEB GUI Interface Setting………………………………………………………..11
4.1. Status……………………………………………………………………….11
4.2. Wizard Configuration………………………………………………………14
4.2.1. Gateway Mode……………………………………………………...14
4.2.2. WiFi Repeater Mode………………………………………………..16
4.2.3. Wisp Operation Mode………………………………………………19
4.2.4. AP Operation Mode………………………………………………...21
4.3. Advanced Setting…………………………………………………………..22
4.3.1. Device Status……………………………………………………….22
4.3.2. Wireless Setting…………………………………………………….23
4.3.3. Virtual AP……………………………………………………………25
4.3.4. Access Control………………………………………………………26
4.3.5. Advanced Settings…………………………………………………..27
4.3.6. Network Setting…………………………………………………….27
4.3.7. Management………………………………………………………..28
5. Share Internet and obtain IP address automatically……………………………..30
Troubleshooting……………………………………………………………………...31

DG-WM6305SIE2 User Manual
4
1. Hardware and Operation mode Instruction
Package Contents
Before using this access point, please check if there is anything missing in the
package, and contact your dealer of purchase to claim for missing items:
DG-WM6305SIE2 Ceiling Mount AP Router

DC 12V Power Adapter
Patch Cord
User Manual CD

Mounting Screws
1.1. LED Indicator
Green:- Power Indicator
Blue:- WiFi Indicator
1.2. AP Router Interface
RST
Reset Button, it make AP Router revert to default settings after pressing it
for 15 seconds.
WAN
WAN Port, connect with ADSL modem or Internet mainly. It will be LAN port
under Wireless AP Router and WiFi Repeater operation mode
LAN LAN Port to end users
LED
LED Indicator for WAN port and LAN port
DC
DC power connector

DG-WM6305SIE2 User Manual
5
1.3. Power Supply:
1.3.1. PoE Adapter Power Supply:
The connection diagram showed as P1, internet cable connect to PoE adapter’s LAN
Port, Ceiling AP Router’s WAN port connect to PoE adapter’s PoE Port, then PC will
access into ceiling AP through cable or wireless. The wireless AP Router support 48V
IEEE 802.3af standard PoE, the PoE adapter should be 48V PoE standard.
P1
1.3.2. PoE Switch Power Supply:
The connection diagram showed as P2, Internet cable from PoE Switch to Ceiling AP’s
WAN Port, then PC access into ceiling AP wired/wireless.If the PD wireless AP
support 48V IEEE 802.3af standard PoE, then the PoE switch should comply with
802.3af 48V PoE standard.
P2
Operation Mode:
There are three operation mode on this wireless AP:
D
D

DG-WM6305SIE2 User Manual
6
P3
P4
P5
D
D
D
D
D

DG-WM6305SIE2 User Manual
7
1.4. AP Router Installation:
The Ceiling Wireless AP Router, will be installed under ceiling based on following
steps:
P6

DG-WM6305SIE2 User Manual
8
2. Connect Wireless AP Router with PC
Connect the PC with wireless AP by Wireless SSID and LAN cable:
The diagram of wireless connection showed as follow:
Pls note: the default SSID is DG-WM6305SIE2-2.4G/5.8G, SSID’s are open with no
password.
P7: Connecting the PC to the AP with wireless
P8: Connecting the PC to the AP with wired LAN

DG-WM6305SIE2 User Manual
9
3. Login
1. Connect the Ceiling AP Router with computer by wired or wireless
2. The default IP address of this wireless AP Router is 192.168.1.200. Configure the
PC’s local connection. IP address as 192.168.1.X (X is number from 2 to 254), subnet
mask is 255.255.255.0.
P9
P10

DG-WM6305SIE2 User Manual
10
3. Input 192.168.1.200 into browser, login page will appear, the default login
password: admin.
P11: Login Page
4. After login the following page appear which shows Device Status. This page will
show the device default operation mode, Channel, Connection status, CPU usage,
Wireless settings, LAN Setting, Wireless AP’s Location, Hardware/Firmware version.
P12: Device Status

DG-WM6305SIE2 User Manual
11
4. WEB GUI interface Setting
4.1. Status
After login, the Device Status and home page will be showed
P13: Device Status
This page, show the device default operation mode, channel, end user QTY,
connection status, CPU usage status, Wireless, LAN and AP location info.
In this ceiling wireless AP, the default operation mode is AP mode.
Then in 2.4G Wireless Setting, GUI configuration page shown as below:
User can configure the SSID, Password, Band width, Channel then Apply to finish.

DG-WM6305SIE2 User Manual
12
P14: 2.4G Wireless Setting
Then in 5G Wireless Setting, GUI configuration page shown as below:
User can configure the SSID, Password, Band width, Channel then Apply to finish.
P15: 5G Wireless Setting

DG-WM6305SIE2 User Manual
13
As shown below user can set LAN Setting to configure the DHCP or Static IP address.
P16: LAN Setting
AP location setting: can mark where the AP set up, and AP name.
P17: AP Location Setting

DG-WM6305SIE2 User Manual
14
4.2. Wizard Configuration
Wizard: It instruct users to configure wireless AP Router’s operation mode based on
needs, there are four operation mode including Gateway, Repeater, WISP, Wireless
AP. Please confirm the operation mode first before starting the configuration.
Clicking Wizard in Status page will pop up following page to configure the operation
mode and there are explanation for each operation mode for better application.
P18: Wizard Configuration
4.2.1 Gateway Mode
Before Clicking the Gateway mode, confirm your internet will be Static IP, PPPoE, or
DHCP. Then clicking on the Gateway mode will pop up the below image. Please
choose the right WAN setting mode, then click next to continue. Then configure the
wireless parameters and click next.
P19: WAN Setting in Gateway Mode

DG-WM6305SIE2 User Manual
15
P20: Wireless Setting in Gateway Mode
Please note: to make the device work in some clear channel, user can click wireless
analyzer at first. Check Less AP in the channel, and then select your channel
accordingly, then Wireless performance will be more stable. Picture shown as below:
P21: 2.4G Wireless Analyzer
Clicking next will complete the Gateway mode setting and show following picture:
Please Note: The equipment will restart automatically for the changes to take effect.

DG-WM6305SIE2 User Manual
16
P22: Settings Complete in Gateway Mode
When return to Status page, will show Wireless router’s SSID, Internet connection,
LAN connection status shown as below.
P23: Status in Gateway Mode
4.2.2. WiFi Repeater mode
1. Login the Web management page, click “Wizard” then “WiFi Repeater”
2. Scan AP and select the AP’s SSID want to bridge then input the AP’s key, click next
to complete.

DG-WM6305SIE2 User Manual
17
P24: Repeater Mode
Click next to configure the Wireless Setting as follows, then click next to finish.
P25: Wireless Setting in Repeater Mode
Click Return button, will back to Status, show Repeater mode data, will show fail or
success, and user can configure this data in this page if required.
Please Note: The equipment will restart automatically for the changes to take effect.

DG-WM6305SIE2 User Manual
18
P26: Status in Repeater Mode
In wifi repeater operation mode, the default is SSID disable. If you want to enable
SSID, then click Wireless Setting.
Pls note, when click wireless relay setting, following page will pop up, you can make
changes from here easily.
P27: Wireless Relay Settings

DG-WM6305SIE2 User Manual
19
4.2.3. WISP Operation mode
Click WISP operation mode in Wizard, then will pop up the configure page, please set
the WISP operation mode based on the steps shown in picture:
P28: WISP Mode
Select the appropriate wireless AP and configure the correct WAN setting in WISP
operation mode, then next to complete.
Please Note: The equipment will restart automatically for the changes to take effect.
P29: WAN Setting in WISP Mode

DG-WM6305SIE2 User Manual
20
Configure the Wireless Data as shown below
P30: Wireless Setting in WISP Mode
Then complete and back to status, will show the connection fail or success, then can
configure the data based on request:
P31: Status in WISP Mode