Digital Monitoring Products XT INTERNATIONAL Series User manual

© 2018 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.
Silencing an Alarm
When the alarm bell or siren is sounding, enter your user code or present your card to a
keypad or reader during the Status List display.
IS THIS A FALSE ALARM? YES NO or CANCEL VERIFY displays.
• If a burglar alarm is valid, press NO or VERIFY to send a verify message to the
Emergency Monitoring Station. The system will remain armed.
• If a valid alarm has not occurred, press YES or CANCEL to cancel the alarm and send
an Abort or Cancel message to the Emergency Monitoring Station and the security
system will be disarmed.
Note: For Area Systems, this prompt is displayed only if the User Code has the authority to
disarm the area.
Silencing the Trouble Tone
You can silence the trouble tone by pressing any key. This only silences the keypad and does
not correct the condition that originally caused the problem.

XT Series International User Guide i
INTRODUCTION ................................................................. 1
About Your Security System...................................................1
Keypads ...............................................................................2
Common Keys on All Keypads ................................................5
Entering Alpha Characters .....................................................5
Entering Non-Alpha Characters ..............................................6
Keypad User Options.............................................................6
Special Keypad Tones............................................................7
1100 Series Wireless .............................................................8
Special Wireless Displays.......................................................9
Special Keypad Displays ........................................................9
Security System Terms ........................................................ 10
ARMING AND DISARMING ............................................... 13
How Your System Operates .................................................13
Arming Functions................................................................14
Area System Arming............................................................15
Area System Disarming .......................................................16
All/Perimeter System Arming ...............................................18
All/Perimeter System Disarming ...........................................20
Home/Away System Arming.................................................21
Home/Away System Disarming ............................................ 22
Keypad Shortcut Keys .........................................................23
USER MENU ...................................................................... 25
Accessing the User Menu.....................................................25
User Menu Options .............................................................25
Zone Activity Check.............................................................26
Sensor Reset ......................................................................26
Outputs On/Off...................................................................27
Favorite..............................................................................27
Z-Wave Setup.....................................................................28
Wi-Fi Setup ........................................................................33
Bypass Zones .....................................................................35
Zone Monitor (Chime) .........................................................36
System Test........................................................................37
Schedules...........................................................................41
Permanent Schedules..........................................................41
Extending Schedules ...........................................................42
Output Schedules ...............................................................42
Favorite Schedules ..............................................................44
Date and Time....................................................................45
Display Events ....................................................................45
Request Service? ................................................................46
XT30INT SERIES USER GUIDE
Table of Contents

ii XT Series International User Guide
SECURITY GRADE 2 OPERATION ..................................... 47
Keypads .............................................................................47
User Menu..........................................................................47
SYSTEM SETUP RECORD................................................... 48
Protection Areas .................................................................48
Output Record ....................................................................48
Z-Wave Device Name ..........................................................49
Favorite List........................................................................50
Key Fob Button Programming ..............................................51
User Codes.........................................................................51
APPENDIX A ..................................................................... 53
About the Display Events Section .........................................53
Zone Activity Check Event Display ........................................53
Zone Event Displays............................................................ 54
Arming and Disarming Event Displays...................................54
User Code Change Event Displays ........................................54
Supervisory Event Displays ..................................................55
System Monitor Event Displays ............................................55
Wireless Jamming Event Displays......................................... 55
Wireless Trouble Event Displays ........................................... 55
APPENDIX B ..................................................................... 56
1100 Series Wireless Description .........................................56
APPENDIX C ..................................................................... 57
Using Door Access ..............................................................57
Entering User Names .........................................................59
APPENDIX D ..................................................................... 60
Common Keypad Displays.................................................... 60

Introduction XT Series International User Guide 1
INTRODUCTION
ABOUT YOUR SECURITY SYSTEM
Your system is designed with your safety and comfort in mind.
It uses the latest in computer technology to create the most
advanced and user-friendly, security, re, and access control
system available.
The system combines ease of use with a simple-to-understand
keypad display to offer the full range of features requested by
today’s security system owners. Your security system can protect
both the interior and perimeter of your home or business while
you are away or just the perimeter when you are inside, giving
you a wall of security and peace of mind.
You can turn portions of your protection on or off at any time by
pressing a few keys. You can add, delete, and change personal
user codes at any time or check the status of all protection
devices in the system.
Keypads
This is the device we have placed at certain locations throughout
the premises that allows you to turn the system protection on and
off using your personal user code.
User Menu
The keypad provides a simple User Menu containing all of the
functions you need to fully operate your system such as changing
the time of day or a personal user code.
A Note About False Alarms
One of the most important concerns facing the security industry
today is false alarms. The accidental dispatching of police and
re agencies places others in jeopardy by limiting the response
capability of those emergency service units.
As part of our commitment to reducing false alarms, we would
like to encourage you to read this guide thoroughly. All the
information contained here can help you quickly, and comfortably,
learn about XT30INT Series system operation.
Note: There may be a 30-second alarm communication delay
pre-programmed at installation to allow disarming if a false alarm
occurs. This delay is optional and can be removed or increased to
45 seconds by your alarm dealer.
Test Your System Weekly
It is recommended that you test the burglary portion of your
system at least once each week. Testing should involve an active
test of all doors, windows, and motion detectors connected to
your system. If your system also has re protection, call the
service department to nd out how this portion of your system
should be tested.
Refer to the System Test section of this guide for instructions on
testing the burglary portion of your system.

2 XT Series International User Guide Introduction
KEYPADS
Your system may have one or more easy to use LCD keypads that allow you to properly operate the system. Below is a brief overview of
the features available on each of the possible keypad options.
32-Character Display
Armed LED
Power LED
Data Entry Digit keys
COMMAND Key
Back Arrow Key
Select Keys
1 2 3 4
9 0 CMD
5 6 7 8
ABC PRINTING
FRI 2:51 AM
Backlit Logo
and Proximity
Antenna
Thinline/Aqualite Keypad
Icon Display
Shortcut and Digit keys
Backlit Logo
and Proximit
y
Antenna COMMAND Key
Back Arrow Key
Select Keys
Thinline Series Icon Keypad
MON 5:35 AM
DISARMED
Panic
Chime
Check-In
Reset
TODAY
WEDNESDAY
82
98 77
80
LO
74
HI
HI LO
CURRENT
Interactive Shield
Proximity Card
Reader
Micro SD
Card Slot
Carousel
Menu
Dealer
Logo
Local Weather
Conditions
Graphic Touchscreen Keypad
32-Character Display
Data Entry Digit keys
COMMAND Key
Back Arrow Key
Select Keys
Backlit Logo
and Proximity
Antenna
SMITH RESIDENCE
FRI 12: 51 PM
Thinline Wireless Keypad

Introduction XT Series International User Guide 3
Select Keys and Areas
For Thinline, Aqualite, Icon, and Wireless Keypads, there are four
keys under the display called select keys. On Graphic Touchscreen
keypad these are referred to as the select areas. These keys or
areas are one of the features that make your system so easy to
operate. They allow you to make selections by pressing the select
key or area under a choice shown in the display.
Note: For the purposes of this guide, when instructed to press the
rst select key or area, press the far left select key or area. The
second select key or area is the second from the left, the third
select key or area is second from the right, and so on.
32-Character Display
Select Area 1
Select Area 3
Select Area 2
Select Area 4
Touch Select Areas
Power/Armed LED
On Thinline and Aqualite Keypads, the power LED indicates the
panel’s power status. It is recommended you contact the service
department when the power LED is off or blinking.
LED OPERATION AC BATTERY
ON (Steady) OK OK
OFF Trouble N/A
BLINKS OK Trouble
The Armed LED is on steady anytime any burglary protection area
is armed and is off when all areas are disarmed.
On Graphic Touchscreen Keypads, the LED indicates the power and
armed status of the panel. Depending on the operation, the LED is
red or blue as listed in the table.
COLOR AND
ACTIVITY
ARMED
STATUS KEYPAD POWER STATUS
Blue Steady Panel Disarmed AC Power OK, Battery OK
Blue Blinking Panel Disarmed AC Power OK, Battery Fault
No Light Panel Disarmed AC Power Fault, Battery OK
Red Steady Panel Armed AC Power OK, Battery OK
Red/Blue Alternate Panel Armed AC Power OK, Battery Fault
Red Blinking Panel Armed AC Power Fault, Battery OK

4 XT Series International User Guide Introduction
On Thinline Wireless Keypads, the backlit logo on the keypad
indicates the keypad power status and the arming status of the
panel. Depending on the operation, the logo displays red or green
as listed in the table.
COLOR AND
ACTIVITY
ARMED
STATUS
KEYPAD POWER
STATUS
Green Steady Panel Disarmed AC Power OK, Battery OK
Green Blinking Panel Disarmed AC Power OK, Battery Fault
No Light Panel Disarmed AC Power Fault, Battery OK
Red Steady Panel Armed AC Power OK, Battery OK
Red/Green Alternate Panel Armed AC Power OK, Battery Fault
Red Blinking Panel Armed AC Power Fault, Battery OK
Panic Functions
Your keypad may be set up to send a panic, emergency, or re
report to the Emergency Monitoring Station. If this option is
programmed for your Thinline, Aqualite, Icon, or Wireless Keypad,
icons display below the top row select keys.
Press and hold the two select keys adjacent to the desired icon
for 2 seconds, until you hear a beep from the keypad.
Top Row Select Keys
Police Emergency Fire
Panic Buttons
For Graphic Touchscreen Keypads, touch the icon for 2 seconds
until a beep is heard.
7/0 Panic Function
Thinline and Aqualite Keypads may also be programmed at
installation to allow the user to initiate an optional Panic alarm by
simultaneously pressing and holding the 7 and 0 (zero) keys. When
the 7 and 0 keys are pressed for a short time, the keypad sends a
Panic alarm report to the Emergency Monitoring Station.
Note: The 7/0 Panic Function is not available on Thinline Icon,
Wireless, or Graphic Touchscreen keypads.
PANIC OPTIONS
PRESS AND HOLD BUT TON TO SEND
FIRE
POLICE EMERGENCY
Graphic Touchscreen Panic Icons

Introduction XT Series International User Guide 5
ENTERING ALPHA CHARACTERS
Some options during programming require you to enter alpha
characters. To enter an alpha character, press or touch the key
that has that letter written below it. The keypad displays the
number digit of the key. Next, press the select key or area that
corresponds to the location of the letter under the key. Pressing
a different select key or area changes the letter. When another
digit key is pressed, the last letter displayed is retained and the
process starts over.
COMMON KEYS ON ALL KEYPADS
Data Entry Digit keys
These keys allow you to enter your user code or other information
into the system.
CMD (command)
The CMD key allows you to advance through the keypad displays,
User Menu, or complete a data entry function.
<— (back arrow)
The back arrow is used to go back through the keypad displays
while operating your system. You can press the back arrow to back
up through the list of functions in the User Menu or to erase the
last character you entered.

6 XT Series International User Guide Introduction
KEYPAD USER OPTIONS
The User Options menu allows you to make adjustments to your
keypad to best t your environment and needs.
On Thinline, Aqualite, Icon, and Wireless Keypads, press and hold
the back arrow and CMD keys for two seconds. The keypad display
changes to SET BRIGHTNESS. Press CMD to display the next option
or the back arrow to exit.
Backlighting Brightness
At the SET BRIGHTNESS display, use the rst select key to lower
the keypad brightness. Use the fourth select key to increase the
brightness.
Note: If the brightness level is lowered, it temporarily reverts
back to maximum intensity whenever a key is pressed.
On Thinline Icon Series keypads, enter the desired brightness from
the range of off (0) to maximum (8).
On Thinline or Aqualite Keypads, this sets the LCD display, AC LED,
and keyboard backlighting brightness level.
On Thinline Icon and Wireless Keypads, this sets the LCD display,
keyboard, and logo backlighting brightness level.
On Graphic Touchscreen Keypads, set the backlight illumination
and AC Power/Armed LED brightness level. In the touchscreen
display below SET BRIGHTNESS, press the left < to lower and
the right >to raise the backlight brightness. If the screen is not
pressed, and the speaker has not sounded for 30 seconds, the
user-selected standby brightness level restores.
ENTERING NON-ALPHA CHARACTERS
To enter a space in an alpha entry, press the 9digit key followed
by the third select key or area. The three characters on the 9
digit key are Y, Z, and space. You can also enter the following
characters: – (dash), . (period), * (asterisk), and # (pound sign)
using the 0 (zero) key and the four select key or areas from left
to right. For example, to enter a – (dash), press the 0 (zero) key
and then the rst select key or area. A dash now appears in the
keypad display. The table below shows the character locations for
DMP keypads.
KEY
NUMBER
SELECT
KEY 1
SELECT
KEY 2
SELECT
KEY 3
SELECT
KEY 4
1 A B C (
2 D E F )
3 G H I !
4 J K L ?
5 M N O /
6 P Q R &
7 S T U @
8 V W X ,
9 Y Z space _
0 - . * #