Digital Projection HIGHlite 730 Series User manual

Rev E March 2014
USER MANUAL
INSTALLATION AND QUICK-START GUIDE
CONNECTION GUIDE
OPERATING GUIDE
REMOTE COMMUNICATIONS GUIDE
REFERENCE GUIDE
114-751E
HIGHlite 730 Series
HIGHlite 740 Series
High Brightness Digital Video Projector

i
Rev E March 2014
Digital Projection HIGHlite 730 & 740 Series
i
About This Document
Please follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.
Keep this manual handy for future reference.
Symbols used in this manual
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners.
Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.
Copyright © 2014 Digital Projection Ltd. All rights reserved.
Notes

ii
Rev E March 2014
Digital Projection HIGHlite 730 & 740 Series
ii
Introduction
Congratulations on your purchase of this Digital Projection product.
Your projector has the following key features:
• Full range of digital and legacy analog inputs
• Control of most aspects of the projector’s operation via LAN and RS232
• Support for a number of aspect ratios and screen sizes
• Non-linear warp adjustment by moving points on an interpolated grid
• Ceiling mount and rear-screen installation options
• Simultaneous display of two sources via Picture-In-Picture
• Long lamp life
• Motorised lens mount
A serial number is located on the back of the projector. Please record it here:
Notes

iii
Rev E March 2014
Digital Projection HIGHlite 730 & 740 Series
iii
CONTENTS
INSTALLATION AND QUICK-START GUIDE..............................1
WHAT’S IN THE BOX? ................................................................... 3
CONNECTING THE POWER SUPPLY ............................................. 4
PROJECTOR OVERVIEW ............................................................... 5
Front and rear views ............................................................................. 5
Control panel indicators ........................................................................ 6
REMOTE CONTROL....................................................................... 7
Infrared reception.................................................................................. 9
POSITIONING THE SCREEN AND PROJECTOR........................... 10
CHANGING THE LENS................................................................. 11
Inserting a new lens ............................................................................ 11
Removing the lens .............................................................................. 12
OPERATING THE PROJECTOR.................................................... 13
Switching the projector on................................................................... 13
Switching the projector off................................................................... 13
Selecting an input signal or test pattern.............................................. 14
Input signal ........................................................................................ 14
Test pattern ........................................................................................ 14
Adjusting the lens................................................................................ 15
Zoom................................................................................................ 15
Focus ............................................................................................... 15
Shift ................................................................................................. 15
Adjusting the image............................................................................. 16
Orientation ......................................................................................... 16
Keystone ........................................................................................... 16
Picture .............................................................................................. 16
CONNECTION GUIDE ............................................................................17
SIGNAL INPUTS AND OUTPUTS.................................................. 19
EDID on the DVI and VGA inputs........................................................ 21
Using HDMI/DVI switchers with the projector ..................................... 21
CONTROL CONNECTIONS........................................................... 22
LAN connection examples .................................................................. 23
RS232 connection example ................................................................ 24
OPERATING GUIDE ................................................................................25
USING THE MENUS ..................................................................... 27
Menus and sub-menus........................................................................ 27
Drop-down lists ................................................................................... 28
Sliders ................................................................................................. 29
Commands.......................................................................................... 29
Editing elds........................................................................................ 30

iv
Rev E March 2014
Digital Projection HIGHlite 730 & 740 Series
iv
USING THE PROJECTOR............................................................. 31
Main menu .......................................................................................... 31
Lens menu .......................................................................................... 32
Zoom................................................................................................ 32
Focus ............................................................................................... 32
Center Lens ....................................................................................... 32
Nudge............................................................................................... 32
Image menu ........................................................................................ 33
Video Filters ....................................................................................... 33
VGA Setup......................................................................................... 33
Color menu.......................................................................................... 34
Gamut .............................................................................................. 34
Black Level and Gain sliders................................................................... 34
Geometry menu .................................................................................. 35
Aspect Ratio....................................................................................... 35
Overscan........................................................................................... 35
Size & Position.................................................................................... 36
Geometry Engine................................................................................. 37
Edge Blend menu................................................................................ 43
Overview ........................................................................................... 43
Array H Position and V Position............................................................... 44
S-Curve Value .................................................................................... 45
Blending............................................................................................ 47
Segmentation ..................................................................................... 48
Blend Width........................................................................................ 50
Black Level Uplift ................................................................................. 50
Reduce Black Level Uplift Width .............................................................. 51
Blending images from multiple projectors ........................................... 54
Before you start................................................................................... 54
Edge Blend procedure .......................................................................... 55
PIP menu ............................................................................................ 63
Lamps menu ....................................................................................... 64
Setup menu......................................................................................... 65
Reset Default Settings .......................................................................... 65
Input Conguration............................................................................... 66
Network ............................................................................................ 67
On Screen Display ............................................................................... 68
System ............................................................................................. 69
Setting up an IR address ....................................................................... 70
Information menu ................................................................................ 71
Lamps .............................................................................................. 71
Conguration...................................................................................... 71
REMOTE COMMUNICATIONS GUIDE ..........................................73
INTRODUCTION........................................................................... 75
Network setup ..................................................................................... 75
Serial Port setup.................................................................................. 75
Simplied protocol commands ............................................................ 76
Examples .......................................................................................... 76
CONTENTS (continued)

v
Rev E March 2014
Digital Projection HIGHlite 730 & 740 Series
v
COMMAND GUIDE ....................................................................... 77
Inputs .................................................................................................. 77
Test patterns........................................................................................ 77
Lens .................................................................................................... 79
Image .................................................................................................. 79
Color.................................................................................................... 81
Geometry ............................................................................................ 82
Edge Blend.......................................................................................... 83
PIP ...................................................................................................... 85
Lamps ................................................................................................. 85
Setup................................................................................................... 87
Information .......................................................................................... 88
WEB CONFIGURATION UTILITY .................................................. 89
Menu examples................................................................................... 89
Using the Discovery Tool to view your network................................... 91
REFERENCE GUIDE................................................................................93
THE DMD™.................................................................................. 96
CHOOSING A LENS ..................................................................... 98
Basic calculation ................................................................................. 99
Basic calculation example................................................................. 100
Full lens calculation........................................................................... 101
Introducing TRC ................................................................................ 101
Calculating TRC ................................................................................ 102
TRC table ........................................................................................ 102
Calculating the throw ratio with TRC ....................................................... 103
Full lens calculation example ............................................................ 104
SCREEN REQUIREMENTS......................................................... 105
Fitting the image to the DMD™......................................................... 105
1080p images displayed full width .......................................................... 105
1080p images displayed full height......................................................... 106
WUXGA images displayed full width ....................................................... 107
WUXGA images displayed with a height of 1080 pixels................................ 107
WUXGA images displayed full height ...................................................... 108
Diagonal screen sizes....................................................................... 109
Fitting the image to the screen.......................................................... 110
Positioning the screen and projector..................................................111
POSITIONING THE IMAGE..........................................................112
Maximum offset range....................................................................... 114
ASPECT RATIOS EXPLAINED.....................................................115
Aspect ratio examples for DMD™ resolution 1080p ......................... 116
Aspect ratio examples for DMD™ resolution WUXGA...................... 119
Aspect ratio example: TheaterScope................................................ 122
FRAME RATES AND PULLDOWNS EXPLAINED......................... 123
Interlaced and progressive scan ....................................................... 123
Frame rates of image sources .......................................................... 123
Pulldowns - conversion into destination formats............................... 124
2:3 (normal) pulldown ......................................................................... 124
2:3:3:2 (advanced) pulldown................................................................. 125
APPENDIX A: LENS PART NUMBERS........................................ 126
CONTENTS (continued)

vi
Rev E March 2014
Digital Projection HIGHlite 730 & 740 Series
vi
APPENDIX B: LENS CHARTS .................................................... 127
How to use the lens charts................................................................ 127
How to nd the right lens chart......................................................... 128
1080p (1920 x 1080 pixels) .................................................................. 128
WUXGA (1920 x 1200 pixels)................................................................ 129
DMD™ resolution 1080p / WUXGA, full DMD™ width images......... 130
DMD™ resolution 1080p, 1.25:1 images .......................................... 131
DMD™ resolution 1080p, 1.33:1 images .......................................... 132
DMD™ resolution 1080p, 1.6:1 images ............................................ 133
DMD™ resolution 1080p, 1.66:1 images .......................................... 134
DMD™ resolution WUXGA, 1.25:1 images....................................... 135
DMD™ resolution WUXGA, 1.33:1 images....................................... 136
APPENDIX C: SUPPORTED SIGNAL INPUT MODES .................. 137
APPENDIX D: MENU MAP.......................................................... 140
APPENDIX E: WIRING DETAILS................................................. 147
Signal inputs and outputs.................................................................. 147
Input 1: VGA..................................................................................... 147
Input 2: HDMI ................................................................................... 148
Output: SPDIF .................................................................................. 148
Input 3: DVI...................................................................................... 149
Input 4: 3G-SDI ................................................................................. 150
Input 5: Composite 1 .......................................................................... 150
Input 6: S-Video ................................................................................ 150
Input 7: Component............................................................................ 150
Input 8: CVBS................................................................................... 150
Control connections .......................................................................... 151
Wired remote control .......................................................................... 151
RS232 ............................................................................................ 152
CONTENTS (continued)
LAN connection................................................................................. 152
APPENDIX F: GLOSSARY OF TERMS........................................ 153
TECHNICAL SPECIFICATIONS .................................................. 162
Models............................................................................................... 162
Inputs and outputs............................................................................. 163
Bandwidth ......................................................................................... 163
Remote control and keypad .............................................................. 163
Automation control ............................................................................ 163
Color temperature ............................................................................. 163
Lamps ............................................................................................... 164
Lenses............................................................................................... 164
Lens mount ....................................................................................... 164
Mechanical mounting ........................................................................ 164
Orientation......................................................................................... 164
Electrical and physical specications................................................ 165
Safety & EMC regulations................................................................. 165
Accessories....................................................................................... 165

Digital Projection HIGHlite 730 & 740 Series
This page is intentionally left blank.

Rev E March 2014
INSTALLATION AND QUICK-START GUIDE
HIGHlite 730 Series
HIGHlite 740 Series
High Brightness Digital Video Projector

Digital Projection HIGHlite 730 & 740 Series IN THIS GUIDE Installation and Quick-Start Guide
Rev E March 2014
IN THIS GUIDE
What’s In The Box?............................................................................................. 3
Connecting The Power Supply........................................................................ 4
Projector Overview............................................................................................. 5
Front and rear views ...................................................................................................5
Control panel indicators.............................................................................................6
Remote control .................................................................................................... 7
Infrared reception........................................................................................................9
Positioning The Screen And Projector....................................................... 10
Changing The Lens........................................................................................... 11
Inserting a new lens..................................................................................................11
Removing the lens ....................................................................................................12
Operating The Projector ................................................................................. 13
Switching the projector on.......................................................................................13
Switching the projector off.......................................................................................13
Selecting an input signal or test pattern.................................................................14
Input signal......................................................................................................................14
Test pattern .....................................................................................................................14
Adjusting the lens .....................................................................................................15
Zoom...............................................................................................................................15
Focus ..............................................................................................................................15
Shift.................................................................................................................................15
Adjusting the image..................................................................................................16
Orientation ......................................................................................................................16
Keystone .........................................................................................................................16
Picture.............................................................................................................................16

Digital Projection HIGHlite 730 & 740 Series WHAT’S IN THE BOX? Installation and Quick-Start Guide
3
Rev E March 2014
What’s In The Box? Notes
Make sure your box contains
everything listed. If any pieces are
missing, contact your dealer.
You should save the original box
and packing materials, in case you
ever need to ship your projector.
The projector is shipped without a
lens.
Only one power cable - dependent
on the destination territory - will be
supplied with the projector.
Remote control
(105-023)
4x AAA batteries
Power cable, United Kingdom
(112-000)
User Guides on CD
(114-749)
Important Information (114-750)
Power cable, Europe
(112-001 )
Power cable, North America
(112-002)
Projector
VGA HDMI DVI 3GSDI
CVBS1 SVIDEO
CLOSE
12 3 4
COMP CVBS2
5 6 7 8
9 0 10+ #
MAIN SUB DUAL HD-T
OFF ON
ALT ROLL
PITCH YAW
FOCUS CAL
SHIFT ZOOM
EYE
SWAP
MAIN/PIP
SWAP
BRI CON GAMMA 3D
ON/OFF
PIP
ON/OFF
LOAD SAVE TEST ADDR
BACKLIGHT
RGB
PRESET
SHUTTER
OPEN
POWER
MENU
OK
EXIT INFO
Power cable,
China (112-817)

Digital Projection HIGHlite 730 & 740 Series CONNECTING THE POWER SUPPLY Installation and Quick-Start Guide
4
Rev E March 2014
Connecting The Power Supply
Lift the cable lock up, push the mains connector in rmly and
push the lock down to secure the cable.
1AC mains inlet with cable lock
Rear view of the projector
1
Notes
Use only the power cable
provided.
Ensure that the power outlet
includes a ground connection as
this equipment MUST be earthed.
Handle the power cable carefully
and avoid sharp bends. Do not
use a damaged power cable.

Digital Projection HIGHlite 730 & 740 Series PROJECTOR OVERVIEW Installation and Quick-Start Guide
5
Rev E March 2014
Projector Overview
Front and rear views
1Front infrared window
2Lens
3Air outlet
4Adjustable feet
5Control panel
6Rear infrared window
7Connection panel
8Power switch and power connection
9Air inlet
9
5
8
76
Rear view
Front view
12
4
3Notes

Digital Projection HIGHlite 730 & 740 Series PROJECTOR OVERVIEW Installation and Quick-Start Guide
6
Rev E March 2014
Control panel indicators
1Power indicator
Behavior Meaning
Off The projector is switched off.
On (amber) The projector is in Standby mode.
On (green) The projector is switched on (Normal mode).
2Shutter indicator
Behavior Meaning
On (amber) The shutter is closed.
On (green) The shutter is open.
3Error indicator
Behavior Meaning
On (red) Voltage Error
Flashing Temperature Error
4Lamp 1 and Lamp 2 indicators
Behavior Meaning
On (green) The lamp is switched on (100%).
On (amber) The lamp is switched on (80-99%).
Flashing (green) The lamp is warming up.
Flashing (amber) The lamp is cooling down.
Flashing (red) Lamp Error
5Infrared indicator
Behavior Meaning
Flashing (blue) The projector is receiving input from the remote control.
Notes
During startup all LEDs light up
at the same time to indicate the
projector is carrying out a self-test.
3
1 2
4 5

Digital Projection HIGHlite 730 & 740 Series REMOTE CONTROL Installation and Quick-Start Guide
7
Rev E March 2014
Remote control
1Transmit indicator
Flashes when the remote control sends a signal to the projector.
Lights solidly when the projector is in LENS ADJUSTMENT mode.
2Power ON / OFF
3ALT
Press and hold this button, then press a green-labeled button.
4Shutter OPEN / CLOSE
5MENU
Access the projector OSD (on-screen display).
6Navigation
Navigate through the menus with the arrows, conrm your choice with OK.
7Input selection
Select input source.
8Image adjustment
Adjust brightness, contrast and gamma.
Press this button while holding the ALT button down to switch red, green and blue
channels on and off.
9Remote control backlight ON / OFF
Make the remote control buttons glow in the dark, or switch this feature off.
continues on next page...
Notes
Only the controls shown highlighted
are used on this projector.
For more information about
LENS ADJUSTMENT mode, see
Adjusting the lens further in this
guide.
Remote control
VGA HDMI DVI 3GSDI
CVBS1 SVIDEO
CLOSE
12 3 4
COMP CVBS2
5 6 7 8
9 0 10+ #
MAIN SUB DUAL AUX
OFF ON
ALT ROLL
PITCH YAW
FOCUS CAL
SHIFT ZOOM
EYE
SWAP
MAIN/PIP
SWAP
BRI CON GAMMA 3D
ON/OFF
PIP
ON/OFF
LOAD SAVE TEST ADDR
BACKLIGHT
RGB
PRESET
SHUTTER
OPEN
POWER
MENU
OK
EXIT INFO
1
2
6
7
8
9
3
4
5

Digital Projection HIGHlite 730 & 740 Series REMOTE CONTROL Installation and Quick-Start Guide
8
Rev E March 2014
Remote control - continued from previous page
10 Lens controls
Adjust position, zoom and focus.
11 PIP ON/OFF
When in PIP mode, display or hide the PIP image.
12 Test
Switch to test pattern.
13 IR address
Set up an address to match the IR address of a projector.
Notes
Only the controls shown highlighted
are used on this projector.
For more information about IR
addresses, see Setting up an IR
address in the Operating Guide.
VGA HDMI DVI 3GSDI
CVBS1 SVIDEO
CLOSE
12 3 4
COMP CVBS2
5 6 7 8
9 0 10+ #
MAIN SUB DUAL AUX
OFF ON
ALT ROLL
PITCH YAW
FOCUS CAL
SHIFT ZOOM
EYE
SWAP
MAIN/PIP
SWAP
BRI CON GAMMA 3D
ON/OFF
PIP
ON/OFF
LOAD SAVE TEST ADDR
BACKLIGHT
RGB
PRESET
SHUTTER
OPEN
POWER
MENU
OK
EXIT INFO
Remote control
10
11
13
12

Digital Projection HIGHlite 730 & 740 Series REMOTE CONTROL Installation and Quick-Start Guide
9
Rev E March 2014
Infrared reception
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is within the angle of
acceptance when trying to control the projector.
Notes
Infrared reception is conrmed by
the blue IR LED ashing on the
control panel.
The infrared receivers are disabled
when a remote control is connected
via a cable. For more information,
see Control Connections in the
Connection Guide.
40°
40°
Infrared reception

Digital Projection HIGHlite 730 & 740 Series POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide
10
Rev E March 2014
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best position for
viewing by your audience.
2. Mount the projector, ensuring that it is at a suitable distance
from the screen for the image to ll the screen. Set the
adjustable feet so that the projector is level, and perpendicular
to the screen.
The dimension drawing below shows the positions of the feet for
table mounting, and the xing holes for ceiling mounting.
1Four adjustable feet
2Six M6 holes for ceiling mount
The screws should not penetrate more than 15 mm
(0.6 in.) into the body of the projector.
Notes
Always allow the projector
to cool for 5 minutes before
disconnecting the power or
moving the projector.
Ensure that there is at least
30 cm (12 in.) of space between
the ventilation outlets and any
wall, and 10 cm (4 in.) on all other
sides.
Do not stack more than three
projectors.
Do not tilt the projector more than
±10° from side to side when in
use, as this may cause serious
lamp failure, damage the lamp
module and cause extra cost on
replacement.
±10° 360°
1
2
1
1
1
2
2
2
2
2

Digital Projection HIGHlite 730 & 740 Series CHANGING THE LENS Installation and Quick-Start Guide
11
Rev E March 2014
Changing The Lens
Inserting a new lens
1. Remove the six screws 1securing the front cover to the body of
the projector.
2. Remove the front cover 2from the projector.
3. Remove the lens from its packaging and remove the two protective
caps from the front and back of the lens.
4. Insert the lens 3into the lens aperture, making sure that the plug
on the zoom drive mechanism lines up with the socket 4on the
right of the lens aperture.
5. Push the lens in rmly as far as it will go.
6. Rotate the lens clockwise as far as it will go.
7. Replace the front cover and secure it with the six screws.
Notes
Before changing the lens,
always make sure the projector
is switched off and fully
disconnected from its power
supply.
Always allow the lamp to cool for
5 minutes before:
- disconnecting the power
- moving the projector
When changing the lens, avoid
using excessive force as this may
damage the equipment.
Avoid touching the surface of the
lens as this may result in image
impairment.
Take care to preserve the original
lens packaging and protective caps
for future use.
2
1
4
3

Digital Projection HIGHlite 730 & 740 Series CHANGING THE LENS Installation and Quick-Start Guide
12
Rev E March 2014
Removing the lens
1. Remove the six screws 1securing the front cover to the body of
the projector.
2. Remove the front cover 2from the projector.
3. Push down the lens holder tab 3.
4. Rotate the lens anti-clockwise
5. Pull the lens forward to remove it from the lens aperture.
2
1
3
Notes
Before changing the lens,
always make sure the projector
is switched off and fully
disconnected from its power
supply.
Always allow the lamp to cool for
5 minutes before:
- disconnecting the power
- moving the projector
When changing the lens, avoid
using excessive force as this may
damage the equipment.
Avoid touching the surface of the
lens as this may result in image
impairment.
Take care to preserve the original
lens packaging and protective caps
for future use.