Digital Projection TITAN sx+ Pro Series 3 User manual

Rev D November 2012
USER GUIDES
INSTALLATION AND QUICK-START GUIDE
CONNECTION GUIDE
OPERATING GUIDE
REFERENCE GUIDE
112-884D
Titan Pro Series 3
High Brightness Digital Video Projector
The information in this document covers all variants of theTitan 330 and 660 series,
including 2D, 3D, Portrait, Landscape and Ultra Contrast models.

Digital Projection Titan Pro Series 3
Rev D November 2012
About These Guides
Please keep these Guides handy for future reference.
A serial number is located on the back of the projector. Record it here:
Symbols used in these Guides
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners.
Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.
Copyright © 2012 Digital Projection Ltd. All rights reserved.
Notes

Rev D November 2012
Titan Pro Series 3
High Brightness Digital Video Projector
INSTALLATION AND QUICK-START GUIDE

Digital Projection Titan Pro Series 3 CONTENTS Installation and Quick-Start Guide
Rev D November 2012
CONTENTS
What’s In The Box? ..............................................................................Inst 1
Getting To Know The Projector ..................................................Inst 2
Front and rear views ..............................................................................Inst 2
Control panel ..........................................................................................Inst 3
Remote control.......................................................................................Inst 3
Connection panel indicators.................................................................Inst 4
Positioning The Screen And Projector...................................Inst 5
Tilting the projector................................................................................Inst 5
Chassis adjustment ...............................................................................Inst 5
Fitting and adjusting the optional rigging frame.................................Inst 6
Fitting .............................................................................................Inst 6
Stacking .........................................................................................Inst 6
Pitch, Roll and Yaw ........................................................................Inst 6
Redirecting the air outlet duct ..............................................................Inst 7
Fitting The Lens.....................................................................................Inst 8
Lens calibration......................................................................................Inst 8
Operating The Projector ..................................................................Inst 9
Switching the projector on....................................................................Inst 9
Selecting an input signal or test pattern..............................................Inst 9
Input signal.....................................................................................Inst 9
Test pattern ....................................................................................Inst 9
Adjusting the lens ................................................................................Inst 10
Zoom............................................................................................Inst 10
Focus ...........................................................................................Inst 10
Shift..............................................................................................Inst 10
Adjusting the image.............................................................................Inst 10
Orientation and On-Screen Display settings................................Inst 10
Keystone ......................................................................................Inst 10
Picture..........................................................................................Inst 10
Switching the projector off.................................................................. Inst 11

Digital Projection Titan Pro Series 3 WHAT’S IN THE BOX? Installation and Quick-Start Guide
Inst 1Rev D November 2012
What’s In The Box? Notes
Make sure your box contains
everything listed. If any pieces are
missing, contact your dealer.
You should save the original box
and packing materials, in case you
ever need to ship your projector.
The projector is shipped without a
lens.
Only one power cable - dependent
on the destination territory - will be
supplied with the projector.
Remote control
(105-023)
4x AAA batteries
Power cable, United Kingdom
(102-180)
User Guides on CD
(112-889)
Important Information (112-888)
Power cable, Europe
(102-163)
Power cable, North America
(102-165)
Projector
Remote cable
(102-162)

Digital Projection Titan Pro Series 3 GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide
Inst 2Rev D November 2012
Getting To Know The Projector
Front and rear views
Notes
For full details of how to use the
controls and the menu system, see
the Operating Guide.
The Side Connection Panel is
available on 3D models only.
Control
panel
Top
air inlets
Side
Connection
panel
Lens release
lever
Front
infra-red
window
Lens
Lens
motor
Mains
input
Bottom
air inlets Adjustable
feet
Air outlet
duct Rear
infra-red window
Rear
Connection panel

Digital Projection Titan Pro Series 3 GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide
Inst 3Rev D November 2012
Control panel
The indicators on the control panel are as follows:
Power off = NO POWER
green = normal RUNNING mode amber = STANDBY mode
Shutter amber = CLOSED green = OPEN
Notes
The projector uses the standard
Digital Projection infra-red remote
control.
Only the controls shown highlighted
are used on this projector.
For full details of how to use the
controls and the menu system, see
the Operating Guide.
Eachtimealensisttedto
the projector, the calibration
procedure must be carried out.
(See Fitting the Lens)
Remote control
Power Shutter
Menu
controls
Transmit
indicator
Input selection
1–10 selects Inputs 1 to 10
#selects Dual Pipe (input 11)
Image adjustment
Brightness, Contrast and Saturation
use and to adjust sliders Remote
control
backlight
On/Off
(RPY) Lens
calibration
See Fitting the
Lens.
Lens controls
40°
40°
Infra-red
reception

Digital Projection Titan Pro Series 3 GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide
Inst 4Rev D November 2012
Connection panel indicators
The indicators on the rear connection panel are as follows:
All on = Power-On Self Test
Lamps 1,2 off = OFF
green = ON
ashing green = WARM-UP ashing amber = COOL-DOWN
red (projector in standby) = Lamp Comms Error (call service)
red (projector on) = Ballast Comms Error (call service)
ashing red (projector in standby) = Lamp Error on previous operation
ashing red (projector on) = Lamp / Interlock Error
Error ashing = Fan / System Error steady = Voltage Error
IR blue ash = Remote control command received
Inputs The indicators next to the input connectors on both panels are as follows:
off = not selected
green = input selected, signal detected, and in range
ashing green = input selected, but signal not detected or out of range
Error
Lamps
1 2
IR
Rear Connection Panel Side Connection Panel
Notes
For full details of how to use the
controls and the menu system, see
the Operating Guide.
For more information about
the connection panels, see the
Connection Guide.
The Side Connection Panel is
available on 3D models only.

Digital Projection Titan Pro Series 3 POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide
Inst 5Rev D November 2012
Positioning The Screen And Projector
• Install the screen, ensuring that it is in the best position for viewing by your audience.
• Position the projector, ensuring that it is at a suitable distance from the screen for the image to ll the screen.
Tilting the projector
Do not tilt the projector more than is shown in the tilt diagrams, when in use, as this may cause serious lamp failure, damage the
lamp module and cause extra cost on replacement.
Chassis adjustment
If the projector is to be operated from a at surface such as a projector table, then adjustment of projector level should be made by turning
the four feet under the chassis. Set the adjustable feet so that the projector is level, and perpendicular to the screen.
SX+ 330-P
1080p 330-P
WUXGA
330-P
TITAN 330
Ceiling (inverted)
SX+ 660
1080p 660
WUXGA 660
180°
±10°
±10° ±10°
±10° ±10°
±10°
180°
TITAN 660
Desktop
SX+ 660
1080p 660
WUXGA 660
SX+ 330-L
1080p 330-L
WUXGA
330-L
Notes
Always allow the lamp to cool for
5 minutes before:
- disconnecting the power
- moving the projector
Ensure that there is at least
30cm (12in) of space between the
ventilation outlets and any wall,
and 10cm (4in) on all other sides.
Do not place the projector with its
front panel down on a surface, as
this may damage the lens or the
lens release lever.
For further information on screen
requirements and positioning the
projector, see the Reference Guide.

Digital Projection Titan Pro Series 3 POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide
Inst 6Rev D November 2012
Fitting and adjusting the optional rigging frame
Fitting
• Remove the four adjustable feet.
• Secure the rigging frame to the projector, as shown, making sure that the male frame
couplings are at the top. Secure each adaptor plate to the projector (three screws), and
secure each of the adjuster brackets to an adaptor plate (three screws).
Stacking
The projectors can be stacked on top of each other, or suspended below each other.
• Carefully lower each projector down onto the top of the others, making sure that all four
frame couplings engage fully.
• Fit a locking pin into each coupling. A ball in the end of the pin prevents the pin from
falling out – to insert or remove a locking pin, press the button on the end of the pin to
release the ball.
Pitch, Roll and Yaw
• To adjust the pitch, turn either the front pair or the rear pair of vertical adjusters, taking
care to turn both adjusters by the same amount.
• To adjust the roll, turn either the left pair or the right pair of vertical adjusters, taking care
to turn both adjusters by the same amount.
• To adjust the yaw, turn the single horizontal adjuster at the front.
Locking
pin
Vertical
adjusters Horizontal
adjuster
Frame
couplings
Fixing
screws
(2 x 3)
Pitch Roll Yaw
Notes
Always allow the lamp to cool for
5 minutes before:
- disconnecting the power
- moving the projector
Do not place the projector with its
front panel down on a surface, as
this may damage the lens or the
lens release lever.
Do not stack more than 3
projectors.
Do not place heavy objects on top
of the projector chassis. Only the
chassis corners and the rigging
frame are capable of withstanding
the weight of another projector.
Backup safety chains or wires
should always be used with
ceiling mount installations.