Digital Projection SHOWlite 6000gv User manual

SHOWlite 6000gv/5000sx+
LCD Projector
User’s Manual

ii
Declaration of Conformity
Directives covered by this Declaration
89/336/EEC Electromagnetic Compatibility Directive, amended by 92/31/EEC & 93/68/EEC.
73/23/EEC Low Voltage Equipment Directive, amended by 93/68/EEC.
Products covered by this Directive
Large Screen Projector type SHOWlite 5000sx+
SHOWlite 6000gv
Basis on which Conformity is being declared
The products identified above comply with the protection requirements of the above EU
directives, and the manufacturer has applied the following standards:-
EN55022:1998 - Limits and Methods of Measurements of Radio Disturbance Characteristics of
Information Technology Equipment.
EN 55024:1998 - Limits and Methods of Immunity Characteristics of Information
Technology Equipment.
EN 61000-3-2:1998 - Harmonic Current Emissions.
EN 61000-3-3:1998 - Immunity to Voltage Fluctuations and Flicker.
The technical documentation required to demonstrate that the products meet the requirements
of the Low Voltage directive has been compiled by the signatory below and is available for
inspection by the relevant enforcement authorities. The CE mark was first applied in June 2003 to SHOWlite5000sx+
and SHOWlite 6000gv.
Signed:
Authority: D.J. Quinn, Director - Product Development
Date: 23 June 2003
Attention!
The attention of the specifier, purchaser, installer, or user is drawn to special measures and limitations
to use which must be observed when these products are taken into service to maintain compliance
with the above directives. Details of these special measures are available on request, and are also
contained in the product manuals.

iii
Important Information
Precautions
Please read this manual carefully before using your Digital Pro-
jection SHOWlite 6000gv/SHOWlite 5000sx+ Projector and keep
the manual handy for future reference.
Your serial number is located on the bottom of your SHOWlite
6000gv/SHOWlite 5000sx+. Record it here:
CAUTION
To turn off main power, be sure to remove the plug
from power outlet.
The power outlet socket should be installed as near
to the equipment as possible, and should be easily
accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABI-
NET.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED Digital Pro-
jection SERVICE PERSONNEL.
This symbol warns the user that uninsulated volt-
age within the unit may be sufficient to cause elec-
trical shock.Therefore, it is dangerous to make any
kind of contact with any part inside of the unit.
This symbol alerts the user that important informa-
tion concerning the operation and maintenance of
this unit has been provided.The information should
be read carefully to avoid problems.
WARNING
TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EX-
TENSION CORD OR IN AN OUTLET UNLESS ALL THREE
PRONGS CAN BE FULLY INSERTED.
DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE
COMPONENTS INSIDE. ALL SERVICING MUST BE DONE BY
QUALIFIED Digital Projection SERVICE PERSONNEL.
DOC Compliance Notice
This Class B digital apparatus meets all requirements of the Ca-
nadian Interference-Causing Equipment Regulations.
3. GSGV Acoustic Noise Information Ordinance:
The sound pressure level is less than 70 dB (A) according to ISO
3744 or ISO 7779.
In UK, a BS approved power cable with moulded plug has a Black
(five Amps) fuse installed for use with this equipment. If a power
cable is not supplied with this equipment please contact your
supplier.
•IBM is a registered trademark of International Business Machines Cor-
poration.
•Macintosh and PowerBook are registered trademarks of Apple Com-
puter, Inc.
•Other product and company names mentioned in this user's manual
may be the trademarks of their respective holders.
RF Interference
WARNING
The Federal Communications Commission does not allow any
modifications or changes to the unit EXCEPT those specified by
Digital Projection in this manual. Failure to comply with this gov-
ernment regulation could void your right to operate this equip-
ment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protec-
tion against harmful interference in a residential installation.This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the in-
structions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•Consult the dealer or an experienced radio / TV technician for help.
Important Safeguards
These safety instructions are to ensure the long life of your projector
and to prevent fire and shock. Please read them carefully and heed
all warnings.
Installation
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away from
dust and moisture. Tilting the front of the projector up or down by
more than 45° from level could reduce lamp life by up to 20%.
3. Do not place your projector in direct sunlight, near heaters or heat
radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm internal
components.
5. Handle your projector carefully. Do not hold the lens hood and the
terminal covers. Dropping or jarring can damage internal compo-
nents.
6. Do not place heavy objects on top of the projector.
7. If you wish to have the projector installed on the ceiling:
a. Do not attempt to install the projector yourself.
b. The projector must be installed by qualified technicians in or-
der to ensure proper operation and reduce the risk of bodily
injury.
c. In addition, the ceiling must be strong enough to support the
projector and the installation must be in accordance with any
local building codes.
d. Please consult your dealer for more information.
To Dealer or Installer:
To prevent the projector from falling, install it in a place and fasten it in
a way with sufficient strength to support the combined weight (24.0
kg/53.0 lbs) of the projector (18.4 kg/40.6 lbs), the lens (2.0 kg/4.4
lbs) and the ceiling mount(3.2 kg/7.1 lbs) for an extended period of
time as well as to withstand earthquakes.

iv
Power Supply
1. The projector is designed to operate on a power supply of 100-
120 or 200-240 V 50/60 Hz AC. Ensure that your power supply fits
this requirement before attempting to use your projector.
2. Handle the power cable carefully and avoid excessive bending. A
damaged cord can cause electric shock or fire.
3. If the projector is not to be used for an extended period of time,
disconnect the plug from the power outlet.
4. Do not touch the power plug with wet hand. Doing so can cause
electrical shock or fire.
5. Do not touch the power plug during a thunder storm. Doing so
can cause electrical shock or fire.
Cleaning
1. Unplug the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled,
use a mild detergent. Never use strong detergents or solvents such
as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to
scratch or mar the lens.
CAUTION
Do not unplug the power cable from the wall outlet under any one of
the following circumstances. Doing so can cause damage to the pro-
jector:
•While the message "Please wait a moment." appears. This mes-
sage will be displayed after the projector is turned off.
•Immediately after the power cable is plugged into the wall outlet
(the POWER indicator has not changed to a steady orange glow).
•Immediately after the cooling fan stops working (The cooling fan
continues to work for 90 seconds (2 minutes in the optional 160W
Long Life lamp 001-716) after the projector is turned off with the
POWER button).
CAUTION
•Do not try to touch the ventilation outlets as they can become heated
while the projector is turned on.
•Do not put the projector on its side when the lamp is turned on.
Doing so may cause damage to the projector.
•Before shipping this projector, remove the lens and attach the lens
hood cap.
The Lens Shift mechanism may encounter damage caused by im-
proper handling during transportation.
•Do not eject a PC card or LAN card while its data is being ac-
cessed. Doing so can damage your PC card or LAN card.
Lamp Replacement
•To replace the lamp, follow all instructions provided on page 9-2.
•Be sure to replace the lamp when the message "The Lamp has
reached the end of its usable life. Please replace the lamp." ap-
pears. If you continue to use the lamp after the lamp has reached
the end of its usable life, the lamp bulb may shatter, and pieces of
glass may be scattered in the lamp case. Do not touch them as the
pieces of glass may cause injury. If this happens, contact your Digital
Projection dealer for lamp replacement.
•Allow a minimum of 90 seconds (2 minutes in the optional 160W
Long Life lamp 001-716) to elapse after turning off the projector.
Then turn off the main power and disconnect the power cable and
allow 60 minutes to cool the projector before replacing the lamp.
•The projector must be operated with two lamp housings installed
regardless of whether or not the lamp is active. Failure to do so
may degrade the performance of the projector such as screen flicker
or loss of lamp life. If one lamp has reached the end of its usable
life, replace it with a new one as soon as possible.
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are unob-
structed to prevent the build-up of heat inside your projector. Allow
at least 4 inches (10 cm) of space between your projector and a
wall. Allow at least 12 inches (30cm) of space between the outlets
on the left side (when viewed from the front) and the wall.
2. Prevent foreign objects such as paper clips and bits of paper from
falling into your projector. Do not attempt to retrieve any objects
that might fall into your projector. Do not insert any metal objects
such as a wire or screwdriver into your projector. If something should
fall into your projector, disconnect it immediately and have the ob-
ject removed by a qualified Digital Projection service personnel.
3. Do not place any liquids on top of your projector.
4. When using a LAN cable:
For safety, do not connect to the connector for peripheral device
wiring that might have excessive Voltage.
CAUTION
•Do not look into the lens while the projector is on. Serious damage
to your eyes could result.
•Keep any items such as magnifying glass out of the light path of
the projector. The light being projected from the lens is extensive,
therefore any kind of abnormal objects that can redirect light com-
ing out of the lens, can cause unpredictable outcome such as fire
or injury to the eyes.
•Do not cover the lens with the supplied lens hood cap or equiva-
lent while the projector is on. Doing so can lead to melting of the
cap and possibly burning your hands due to the heat emitted from
the light output.
Important Information

v
Table of Contents
1. Introduction
zWhat's in the Box? .................................................................... 1-2
xIntroduction to the Projector ................................................... 1-3
cGetting to Know Your Projector ............................................... 1-4
Attaching the lens hood cap to the lens hood with the supplied
string and rivet ............................................................................ 1-6
Carrying the Projector ................................................................. 1-6
Top Features ............................................................................... 1-7
Te r minal Panel Features ............................................................. 1-8
vRemote Control Features ....................................................... 1-10
Remote Control Precautions ..................................................... 1-12
Remote Control Battery Installation .......................................... 1-12
Operating Range for Wireless Remote Control ........................ 1-12
Using the Remote Control in Wired Operation ......................... 1-13
2. Installation
zSetting Up Your Projector ........................................................ 2-2
Screen Size and Projection Distance ......................................... 2-2
xLens Shift Adjustable Range ................................................... 2-4
cOptional Lens Installation ....................................................... 2-6
vMaking Connections ................................................................ 2-8
Connecting Your PC or Macintosh .............................................. 2-8
To connect Scart Output ............................................................. 2-9
Connecting an External Monitor ................................................. 2-9
Connecting Your DVD Player .................................................... 2-10
Connecting Your VCR or Laser Disc Player .............................. 2-11
Connecting to a Network .......................................................... 2-12
Connecting the Supplied Power Cable ..................................... 2-13
3. Projecting an Image (Basic Operation)
zTurning on the Projector .......................................................... 3-2
xSelecting a Source ................................................................... 3-3
cAdjusting the Picture Size and Position ................................. 3-3
vCorrecting the Horizontal and Vertical Keystone Distortion (3D
Reform) ..................................................................................... 3-4
bOptimizing RGB Picture Automatically .................................. 3-6
nTurning Up or Down Volume .................................................... 3-6
mTurning off the Projector .......................................................... 3-7
4. Convenient Features
zTurning Off the Image and Sound ........................................... 4-2
xEnlarging and Moving a Picture .............................................. 4-2
cGetting the On-line Help and Information .............................. 4-2
vUsing a USB Mouse ................................................................. 4-3
bUsing a USB HUB Function ..................................................... 4-3
nChanging Background Logo ................................................... 4-4
mMaking Freehand Drawings on
,Projected Image (ChalkBoard) ................................................ 4-4
.Lens Memory ............................................................................ 4-5
5. Using the Viewer
zMaking the Most out of the Viewer Function ......................... 5-2
xOperating the Viewer Function from the Projector
(playback) ................................................................................. 5-3
6. Using the Projector in a Network
zEnd User License Agreement ................................................. 6-2
xIntroduction ............................................................................... 6-3
cSupported Projectors ............................................................... 6-4
vEquipment Connections and Settings .................................... 6-5
bSoftware Installation ................................................................ 6-6
nStarting/Exiting the Software .................................................. 6-7
mTroubleshooting ........................................................................ 6-8
7. Setting Up for Double Stacking in Link Mode
zStacking and Connecting the Projectors ............................... 7-2
xAdjusting and Registering Signals to Be Projected .............. 7-5
cAdjusting the Lens Shift, Zoom and Focus to Clearly Display
all projected patterns .............................................................. 7-5
vLink Mode Setting .................................................................... 7-5
bList of Menu Items Available in Link Mode ............................ 7-6
8. Using On-Screen Menu
zBasic Menu Operation .............................................................. 8-2
xList of Direct Button Combinations ........................................ 8-3
cMenu tree ................................................................................... 8-4
vMenu Descriptions & Functions .............................................. 8-7
Adjust (Source) ........................................................................... 8-8
Picture ................................................................................. 8-8
Video Adjust ........................................................................ 8-8
Picture Management ........................................................... 8-9
Image Options ................................................................... 8-10
Option Adjust ..................................................................... 8-10
Lens Memory ..................................................................... 8-11
Signal Type ........................................................................ 8-11
Sound ....................................................................................... 8-11
Ref. Adjust ................................................................................ 8-12
Using 3D Reform ............................................................... 8-12
Screen Type ....................................................................... 8-12
Reference White Balance .................................................. 8-12
Reference Color Correction ............................................... 8-12
Reference Lens Memory ................................................... 8-13
Factory Default ......................................................................... 8-13
Projector Options ...................................................................... 8-13
Menu ................................................................................. 8-13
Setup ................................................................................. 8-15
Lamp Settings ................................................................... 8-18
Link Mode .......................................................................... 8-18
LAN Mode ......................................................................... 8-19
Setting a Password ............................................................ 8-23
Security ............................................................................. 8-24
Tools ......................................................................................... 8-25
Timer ................................................................................. 8-25
Using Capture (SHOWlite 6000gv only) ............................ 8-27
Using PC Card Files .......................................................... 8-27
Using ChalkBoard ............................................................. 8-27
Help .......................................................................................... 8-27
Contents ............................................................................ 8-27
Source Information ............................................................ 8-27
Projector Information ......................................................... 8-28
Test Pattern ............................................................................... 8-28
9. Maintenance Replacing the Lamp ........... 9-2
zReplacing or Cleaning the Filter ............................................. 9-3
xCleaning the Cabinet and the Lens ......................................... 9-4
10. Appendix
z USB Memory Device or USB Memory Card Reader Support ........ 10-2
xTroubleshooting ...................................................................... 10-3
cSpecifications ......................................................................... 10-5
vCabinet Dimensions ............................................................... 10-7
bPin Assignments of D-Sub RGB Input Connector ............... 10-7
nCompatible Input Signal List ................................................. 10-8
mREMOTE 1 Connector ............................................................ 10-9
,PC Control Codes and Cable Connection .......................... 10-10
Cable Connection ................................................................... 10-10
PC Control Connector (D-SUB 9P) ......................................... 10-10
.Using Software Keyboard .................................................... 10-10
⁄0 Operation Using an HTTP Browser ..................................... 10-11

1
Introduction
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
zWhat's in the Box? ....................................................1-2
xIntroduction to the Projector ..................................... 1-3
cGetting to Know Your Projector ................................. 1-4
Attaching the lens hood cap to the lens hood with the supplied string and rivet . 1-6
Carrying the Projector ......................................................................................... 1-6
Top Features ........................................................................................................ 1-7
Te r minal Panel Features ...................................................................................... 1-8
vRemote Control Features ....................................... 1-10
Remote Control Precautions ............................................................................. 1-12
Remote Control Battery Installation ................................................................... 1-12
Operating Range for Wireless Remote Control ................................................. 1-12
Using the Remote Control in Wired Operation .................................................. 1-13

1-2
zWhat's in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your Projector.
NOTE: Lenses are optional. Order lenses from your Digital Projection dealer.
Document
1. Introduction
3DREFORM
3DA
SELECT
LENS SHIFT
FOCUSZOOMDOWN
LEFTRIGHT
UP
Z
STATUS
PCCARD2
PCCARD1 LAMP1 LAMP2 POWER
ON/STANDBY
AUTOADJUST
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
F
Lens hood cap
(024F37661)
Projector
Te r minal cover
(Left and Right)
String
(024C04541) and
rivet
(024C04531)
Remote control (079646633) and
batteries (AAA  2)
Remote cable
(073499391)
Power cable for Europe (AC 230V)
(07N080003)
Power cable for North America (AC 120V)
(07N080208)
Important
Information
User’s Manual
(7N950401)
User Supportware
(7N950361)

1-3
xIntroduction to the Projector
This chapter introduces you to the SHOWlite 5000sx+/SHOWlite
6000gv high end fixed installation projector and describes key
features and controls.
Congratulations on Your Purchase of the SHOWlite
5000sx+/SHOWlite 6000gv projector
The SHOWlite 5000sx+/SHOWlite 6000gv is our most sophisti-
cated three panel, dual lamp XGA LCD projector. With the
SHOWlite 5000sx+/SHOWlite 6000gv you will be able to project
images up to 500" (measured diagonally) from your DVD player,
VCR, satellite hookup, HDTV source, PC, Workstation or
Macintosh computer (desktop or notebook) and images from you
digital camera PC Card or compact flash memory. The SHOWlite
5000sx+/SHOWlite 6000gv incorporates integrated networking
access through the RJ45 input or provides for wireless network
connectivity from an optional wireless network PC card. With
extensive input and output panels, optional long life lamp, full
suite of quick-change lenses and a full function remote, the
SHOWlite 5000sx+/SHOWlite 6000gv will let you immerse your-
self in large screen viewing.
Features you’ll enjoy on the SHOWlite 5000sx+/SHOWlite 6000gv:
•Integrated RJ45 connector for wired networking ability
•Two optional modular card slots allow for future projector growth
with the ability to add additional input cards
•Dual PC card slots provide for optional wireless/wired network
connectivity or PC Card usage
•Email projector error status information to selected individuals
•Power Horizontal and Vertical lens shift for optical display cor-
rections
•Lens memory controls lens attributes (zoom, focus, shift) de-
pending on input resolution and input selected for fast and easy
source transitions
•Digital Projection DigiView for enhanced video image display,
more vibrant colors and blacks richer with detail
•DigiScale enhanced image technology for increased projector
versatility that provides for horizontal, vertical and diagonal
keystone correction (allows for positioning the projector in off
center locations in the room and still get aligned images)
•Display 16:9 or 4:3 information and fill the screen
•HDTV (1080p, 1080i, 720p) and SDTV (576p, 576i, 480p, 480i)
compatibility
•SHOWlite 6000gv supports a native resolution of XGA
(1024•768) and SHOWlite 5000sx+ supports a native resolu-
tion of SXGA+ (1400•1050).
•Intelligent lamp technology offers up to six user lamp settings
to maximize light output or lamp life and provide for built in
redundancy
•Smart security settings for password protection, control panel
lock, menu lock and PC card protection key to help prevent
unauthorized access and adjustments to the projector
•ADA508 and Executive Order 13221 Federal Government com-
pliance *1
•DigView 10-bit video decoder for expanded black levels and
adaptive gamma correction
•High performance optional long life lamp for low total operat-
ing costs
•Digital photo viewer to display larger than life images from your
digital cameras PC card or compact flash card
•Double stackable for built in redundancy and high light output
requirements
•Built in 5W2 speakers for an integrated audio solution
•Two timer settings - On/Off with programming or Sleep timer
that counts down at selected intervals
•12V low voltage Screen Trigger output
•Easy set up and operation
•Eco-mode™ lamp technology for increased lamp life and en-
ergy savings
•DigiView for uncompromising display of video and data. Im-
proves white level, color accuracy, dynamic range, and display
of varying levels of black in an image
•Wireless remote control operation
• External control via RS232, USB or Network
•DigiScale intelligent pixel blending technology provides for ex-
tremely accurate image compression and HDTV (1920•1080)
display resolution*2.
•Supports most IBM VGA, SVGA, XGA, Macintosh, component
signal (YCbCr/YPbPr) or other RGB signals within a horizon-
tal frequency range of 15 to 100 kHz and a vertical frequency
range of 48 to 120 Hz. This includes NTSC, NTSC4.43, PAL,
PAL-M, PAL-N, PAL60 and SECAM standard video signals
NOTE: Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S. and Canada.
NTSC4.43: TV standard used in Middle East countries.
PAL: TV standard used in Western Europe.
PAL-M: TV standard used in Brazil.
PAL-N: TV standard used in Argentine, Paraguay and Uruguay.
PAL60: TV standard used for NTSC playback on PAL TVs.
SECAM: TV standard used in France and Eastern Europe.
*1The SHOWlite 6000gv and 5000sx+ meet ADA508 compliance,
the latest American government regulation which provides for
closed captioning, including a menu system that can be viewed
by colorblind users. This model also meets Executive Order
13221 requirement for standby operation, which consumes less
than 1 watt.
*2HDTV 1080P (1920•1080), HDTV 1080i (1920•1080), HDTV
720 p (1280•720) and 1600•1200 are displayed with DigiScale
on the SHOWlite 6000gv.
HDTV 1080P (19201080), HDTV 1080i (1920•1080) and
1600•1200 are displayed with DigiScale technology on the
SHOWlite 5000sx+.
1. Introduction

1-4
1. Introduction
AUDIO
AUDIO OUT
R
R/Cr
G/Y
B/Cb
V
H/
HV
R
L/MONO
R
L/MONO
R
L/MONO
L/MONO
DVI
RGBOUT
RGB 1
RGB 2
AUDIO
SLOT1SLOT2
VIDEO S-VIDEO
PCCONTROL
IN
IN
OUT
OUT
SCTRIGGERREMOTE2
REMOTE1
LAN
ACIN
USB
(
MOUSE/HUB
)
USB
(
PC
)
PCCARD
2
1
3DREFORM
3D A
SELECT
LENS SHIFT
FOCUS ZOOM DOWN
LEFT RIGHT
UP
Z
STATUS
PCCARD2
PCCARD1 LAMP1 LAMP2 POWER
ON/STANDBY
AUTO ADJUST
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
F
cGetting to Know Your Projector
Controls
*NOTE: Slot for Kensington MicroSaver Security System
This security slot supports the MicroSaver®Security System.
MicroSaver®is a registered trademark of Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc.
Lens hood
Te r minal panel (Left)
AC INPUT
Connect the supplied
power cable’s three-pin
plug here.
Lens (optional)
Lens hood cap
Te r minal panel (Right)
Foot (four)
Rotate to fine-adjust the height of
each foot (max. 0.6”/15mm).
Built-in Security Slot ( )*
Remote sensor
Lamp cover 1 (Right)
Carrying handle
Speaker 5W (Stereo)
Air filter (Right)
Attaching and Removing the Terminal Covers
To remove the terminal cover, push and hold the latch.
To attach the terminal cover, align the protrusions inside and push it until you feel it click into place.
1
2
AUDIO
AUDIO
AUDIOOUT
R
R/Cr
G/Y
B/Cb
V
H/
HV
R
L/MONO
R
L/MONO
R
L/MONO
L/MONO
SLOT1OPTION2
DVI
RGBOUT
RGB1
RGB2
VIDEOS-VIDEO
USBAUSBB PCCARD
PCCONTROL
IN
IN
OUT
OUT
SCTRIGGERREMOTE2
REMOTE1
LAN
ACIN
SOURCE
SA
N/STAND BY
AUTOADJUST

1-5
USB
(
MOUSE/HUB
)
USB
(
PC
)
PC CARD
1
2
PC CONTROL
IN
IN
OUT
OUT
SC TRIGGER REMOTE 2
REMOTE 1
LAN
AC IN
AUDIO
AUDIO
AUDIO OUT
R
R/Cr
G/Y
B/Cb
V
H/
HV
R
L/MONO
R
L/MONO
R
L/MONO
L/MONO
SLOT 1 SLOT 2
DVI
RGB OUT
RGB 1
RGB 2
VIDEO S-VIDEO
3D REFORM
3DA
SELECT
LENSSHIFT
FOCUSZOOMDOWN
LEFT RIGHT
UP
Z
STATUS
PC CARD2
PCCARD 1 LAMP 1 LAMP 2 POWER
ON/STANDBY
AUTO ADJUST
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
F
Depression for foot (4 locations)
1. Introduction
Lamp cover 2 (Left)
Remote sensor
Remote sensor
Speaker 5W (Stereo)
Ventilation (outlet)
Ventilation (outlet)
Air filter (Right)
Ventilation (inlet)
Remote sensor
Remote sensor
Air filter (Left)

1-6
Attaching the lens hood cap to the lens hood with the supplied string and rivet
1. Thread the string through the hole on the lens hood cap.
Lens hood cap
String
2. Use the rivet to attach the string to the bottom of the projector.
AUDIO
AUDIO
AUDIO OUT
R
R/Cr
G/Y
B/Cb
V
H/HV
R
L/MONO
R
L/MONO
R
L/MONO
L/MONO
OPTION 1 OPTION 2
DVI
RGB OUT
RGB 1
RGB 2
VIDEO S-VIDEO
Rivet
3D REFORM
3D A
SELECT
LENS SHIFT
FOCUS ZOOM DOWN
LEFT RIGHT
UP
Z
STATUSPC CARD 2PC CARD 1 LAMP 1 LAMP 2 POWER
ON/STAND BY
AUTO ADJUST
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
F
Carrying the Projector
Always carry your projector by the handle.
Ensure that the power cable and any other cables connecting to video sources are disconnected before moving the projector.
When moving the projector or when it is not in use, cover the lens with the lens hood cap.
CAUTION: Do not put the projector on its side when the lamp is on.
Doing so may cause damage to the projector.
1. Introduction

1-7
3D REFORM
3D A
SELECT
LENS SHIFT
FOCUS ZOOM DOWN
LEFT RIGHT
UP
Z
STATUSPC CARD 2PC CARD 1 LAMP 1 LAMP 2 POWER
ON/STAND BY
AUTO ADJUST
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
F
1
7
2354
61314 118912 10
Top Features
1. POWER Button (ON / STAND BY)( )
Use this button to turn the power on and off when the main
power is supplied and the projector is in standby mode or idle
mode.
NOTE: To turn on or off the projector, press and hold this button for a minimum
of two seconds.
2. POWER Indicator
When this indicator is green, the projector is on; when this
indicator is orange, it is in standby or idle mode. See the Power
Indicator section on page 10-3 for more details.
3. STATUS Indicator
If this light blinks red rapidly, it indicates that an error has oc-
curred, the lamp cover is not attached properly or the projector
has overheated. If this light remains orange, it indicates that
you have pressed a cabinet key while the Control Panel Key
Lock is enabled. See the Status Indicator section on page 10-
3 for more details.
4. LAMP Indicator 1/2
If this light blinks red rapidly, it's warning you that the lamp has
reached the end of its usable life. After this light appears, re-
place the lamp as soon as possible (See page 9-2). See the
Lamp Indicator section on page 10-3 for more details.
5. PC CARD Access Indicator 1/2
Lights while accessing a PC card.
6. 3D REFORM Button
Press this button to enter 3D Reform mode to correct the key-
stone (trapezoidal) distortion, and make the image square.
Press to toggle between Cornerstone and Keystone adjust-
ment mode.
NOTE: Pressing and holding this button for a minimum of 2 seconds will reset
3D Reform correction setting values to zero.
7. AUTO ADJUST Button
Use this button to adjust Position-H/V and Pixel Clock/Phase
for an optimal picture. See page 3-6.
8. MENU Button
Displays the menu.
9. SELECT 왖왔왗왘 (+) (–) / Volume Buttons
왖왔 : Use these buttons to select the menu of the item you
wish to adjust. When no menus appear, these buttons
work as a volume control.
왗왘 : Use these buttons to change the level of a selected menu
item. A press of the 왘button executes the selection.When
the menus or the Viewer tool bar is not displayed, these
buttons can be used to select a slide, or to move the
cursor in Folder List or Slide List.
10. ENTER Button
Executes your menu selection and activates items selected
from the menu.
11. CANCEL Button
Press this button to exit "Menus". Press this button to return
the adjustments to the last condition while you are in the ad-
justment or setting menu.
12. LENS SHIFT 왖왔왗왘 Button
Adjust the lens offset by shifting the projected image position
horizontally and / or vertically.
13. ZOOM Button (+/-)
Zoom the lens in and out.
14. FOCUS Button (+/-)
Adjust the lens focus.
1. Introduction

1-8
1. Introduction
AUDIO
AUDIO
AUDIO OUT
R
R/Cr
G/Y
B/Cb
V
H/
HV
R
L/MONO
R
L/MONO
R
L/MONO
L/MONO
SLOT 1 SLOT 2
DVI
RGB OUT
RGB 1
RGB 2
VIDEO S-VIDEO
3
8
12
4
56
7
Terminal Panel Features
1. RGB 1 Connectors [R/Cr, G/Y, B/Cb, H/V, V] (BNC)
Connect R,G,B,H (Horizontal sync) and V (Vertical sync) out-
puts of external equipment.
If using a component with a combined sync (SYNC) output,
connect it to the H/V terminal. When using luminance and color-
difference signals of HDTV and DVD, connect Pr/Cr to the R,Y
to the G and Pb/Cb to the B input of the projector.
RGB 1 Audio Input Jacks (RCA)
L/MONO:This is your left channel audio input for stereo sound
coming from the RGB Input 1 source.
This also serves as your monaural audio input.
R: This is your right channel audio input for stereo sound from
the RGB Input 1 source.
2. RGB 2 Connector (Mini D-sub 15 Pin)
Connect your computer or other analog RGB equipment such
as IBM compatible or Macintosh computers. This also serves
as a component input connector that allows you to connect a
component video output of component equipment such as a
DVD player. This connector also supports SCART output sig-
nal. See page 2-9 for more details.
RGB 2 Audio Iput Mini Jack (Stereo Mini)
This is where you connect audio output from your computer or
DVD player connected to the RGB2 input. A commercially avail-
able audio cable is required.
3. DVI IN Connector (DVI-D 24 Pin)
This connector can be used to accept digital signal output from
a computer with a DVI connector.
DVI AUDIO Input Mini Jack (Stereo Mini)
This is where you connect the audio output from your com-
puter when connected to the DVI input. A commercially avail-
able audio cable is required.
4. RGB OUT Connector (Mini D-Sub 15 Pin)
You can use this connector to loop your computer image to an
external monitor from the RGB 1 or 2 input source.
5. VIDEO IN Connector (BNC)
Connect a VCR, DVD player, laser disc player, or document
camera here to project video.
VIDEO AUDIO Input Jacks R/L (RCA)
These are your left and right channel audio inputs for stereo
sound from a Video source.
6. S-VIDEO IN Connector (Mini DIN 4 Pin)
Here is where you connect the S-Video input from an external
source like a VCR.
NOTE: S-Video provides more vivid color and higher resolution than the tradi-
tional composite video format.
S-VIDEO AUDIO Input Jacks R/L (RCA)
These are your left and right channel audio inputs for stereo
sound from an S-Video source.
7. AUDIO OUT Jacks R/L (RCA)
You can use this connector to output sound from the currently
selected input source (RGB 1, RGB 2, DVI (DIGITAL), Video
or S-Video).
Output sound level can be adjusted in accordance with the
sound level of the internal speaker.
8. Slot 1/2
For optional RGB, SDI or DVI board.

1-9
USB
(
MOUSE/HUB
)
USB
(
PC
)
PC CARD
2
1
PC CONTROL
IN
IN
OUT
OUT
SC TRIGGER REMOTE 2
REMOTE 1
LAN
AC IN
12 3
7
4
8
9
10 11
5
6
1. USB Port [MOUSE/HUB] (Type A)
Connect a USB mouse. You can operate the menu or Viewer
with a USB mouse via this port.
• A USB-supported scanner or PC peripheral can be connected
to this port. (USB Hub Function. See page 4-3)
2. USB Port [PC] (Type B)
Connect this port to the USB port (type A) of your PC using a
USB cable.This port also serves as a PC Control port by using
Dynamic Image Utility 2.0 included on the supplied CD-ROM.
3. PC CARD Slot 1/2
Insert a PC card, commercially available flash memory card or
Digital Projection optional wireless LAN card here.
There are two slots: Slot 1 and Slot 2.
4. PC CARD Eject Button 1/2
Press to eject a PC card partially. Each slot has its own eject
button: 1 and 2.
5. PC CONTROL Connectors (Mini D-Sub 9 pin)
For system expansion such as PC-Control using Dynamic Im-
age Utility included on the supplied User Supportware CD-
ROM or RS232C control from an external control system.
IN: connect to the external equipment such as a PC or control
system.
OUT: for daisy-chaining multiple projectors and operating them
with the same external equipment. To do so, connect to a sec-
ond projector’ s IN terminal to relay the input at the IN terminal
of the first projector until all the projectors are connected.
6. SC. TRIGGER Mini Jack
When the projector is powered ON the screen trigger output
sends a low voltage trigger to the screen controller and the
screen will go down. When the projector is powered OFF the
screen trigger stops sending a low voltage trigger to the screen
controller and the screen will go up.
NOTE: To use this feature, you must turn on the Screen Trigger function. See
page 8-17.
Terminal Panel Features
1. Introduction
Tip (12V)
Ring (0V)
Sleave (ground. 0V)
Stereo mini cable
(not supplied)
NOTE: Screen controllers are supplied and supported by screen manufacturers.
NOTE: Do not use this jack for anything other than intended use. Connecting
wired remote control to the SC. TRIGGER Mini Jack causes damage to the re-
mote control.
7. LAN Port (RJ-45)
This port is typically used for UTP Ethernet/Fast Ethernet. Use
this connector to control the projector on a LAN. See page
2-12.
8. REMOTE 1 (Mini D-Sub 15 Pin)
This terminal allows external control of the projector by use of
contact closure. See page 10-9.
9. REMOTE 2 Mini Jacks (IN/OUT)
IN: wired remote control input.
OUT: for daisy-chaining multiple projectors and operating them
with the same remote control. To do so, connect to a second
projector’ s IN terminal to relay the input at the IN terminal of
the first projector until all the projectors are connected.
10. Main Power Switch
When you plug the supplied power cable into an active wall
outlet and turn on the Main Power switch, the POWER indica-
tor turns orange and the projector is in standby mode. See
page 3-2.
11. AC IN
Connect the supplied power cable’s three-pin plug here.
Three types of power cable are supplied with this projector:
three-pin type for U. S. A. and Canada.Two-pin type for Europe
and Japan.

1-10
1. Introduction
OFF
+ -
PICTURE
ADJUST
ABC DEF GHI
JKL MNO PQR
STU
,. UNDO CANCEL
TEST
PICTURE
KEYSTONE AMPLITUDE ENTRYLIST
SOUND OSD
MUTE
MAGNIFY
HELPINFO.
POSITION AUTOPIXEL
VWX YZ/
WHITE BAL.
IMAGE
ON
POWER
MENU
ENTER
123
456
7
0
89
ADDRESS
PROJECTOR
R G B
LENS
SHUTTER
BS
+
-
+
-
FOCUS ZOOM
CTL
LENS
2
5
6
7
9
10
12
13
17
20
21
22
24
26
2
5
2
3
1
9
1
8
1
6
1
5
1
4
11
8
4
3
1
vRemote Control Features 1. POWER ON
Press and hold this button for a minimum of two seconds to
turn on the projector when the main power is supplied and the
projector is in standby mode or idle mode.
2. POWER OFF
Press and hold this button for a minimum of two seconds to
turn off the projector.
3. MENU
Press to display the main menu.
While pressing and holding CTL, press this button to display
the Remote Control ID dialog box to specify the remote control
ID. See page 7-2.
4. ENTER
Executes the menu selection and activates items selected from
the menu. When the slider or dialog box is displayed:
Pressing this button confirms adjustments/setting and returns
to the previous menu display.
5. Select (Up/Down/Left/Right)
왖왔:Use these buttons to select the menu of the item you
wish to adjust.
When no menus appear, these buttons work as a volume
control.
왗왘:Use these buttons to change the level of a selected
menu item.
A press of the 왘button executes the selection.
Pressing and holding CTL, then pressing 왗button works as a
Back Space key in the entry screen.
Pressing and holding CTL, then pressing this button moves
the menu, slider, toolbar or dialog box.
6. ADJUST WHITE BAL.
Press to display the Picture Management screen.
7. ADJUST PICTURE
Press to display the Picture adjustment screen. Pressing this
button sequentially selects adjustment screens.
8. IMAGE/PROJECTOR
Press to display the Image Option screen. Pressing this button
sequentially selects Image Options screens.
While pressing and holding CTL, pressing this button rotates
Projector Options screens.
9. Source / Input
Press to select input or to name a signal.
1Selects RGB 1 input.
2Selects RGB 2 input.
3Selects DVI (DIGITAL) input.
4Selects VIDEO input.
5Selects S-VIDEO input.
6Selects Viewer input
7Selects LAN input
8Selects OPTION SLOT 1* (available for optional SDI board)
9Selects OPTION SLOT 2* (available for optional SDI board)
0Sequentially selects: RGB1 (VIDEO) → RGB1 (S-VIDEO) .
*This button toggles between input 1 and 2.
NOTE: While pressing and holding CTL, pressing this button switches to the
selected signal found in the Entry List.

1-11
1. Introduction
OFF
+
-
IC
TURE
ADJUST
BC
DEF
M
WHITE BAL.
IMAGE
ON
POWER
MENU
ENTER
2
ADDRESS
P
RO
BS
27
28
10. UNDO
Press to return the adjustments and settings to the previous
condition. While pressing and holding CTL, pressing this but-
ton clears the entire menus or adjustment/setting screen. At
this time the adjustments/settings are stored in memory ex-
cept the items on the setting screen with "OK" and "Cancel"
buttons such as the Menu and the Setup screen.
11. CANCEL
Press to exit the menu.
Press this button with CTL to return to the previous menu with-
out closing adjustment/setting screen while the menus appear.
This feature allows you to adjust or set several items concur-
rently.
12. INFO
Displays the "Source Information" or "Projector Information"
window. This button toggles between these two windows.
While pressing and holding CTL, pressing this button stores
lens position settings.
13. TEST
Press to display the test pattern. Pressing this button sequen-
tially selects test patterns.
14. HELP
Provides online help.
15. PIXEL
Displays the Position/Clock screen to adjust the clock and
phase.
16. AUTO (RGB only)
Press to adjust Position-H/V and Pixel Clock for an optimal
picture.
17. POSITION
Press to display the Position screen; press again to display the
Blanking screen.
While pressing and holding CTL, pressing this button displays
the Lens Shift adjustment screen.
18. MUTE SOUND
Tu r ns off the sound for a short period of time. Press again to
restore the sound.
19. MUTE OSD
Press to turn off the on-screen display. Press again to restore
the on-screen display.
NOTE: You can also turn off the on-screen display forcibly by pressing and
holding CTL and then pressing MUTE OSD (Forced On-Screen Mute Mode) ;
doing this again restores it. In this case any adjustment will still change the
projector's memory settings. This mode is available even when input is switched
to another or the power is turned off the main power.
20. MUTE PICTURE
Press to turn off the picture for a short period of time. Press
again to restore the picture.
21. KEYSTONE (R)
Press to display the Keystone Correction (3D Reform) screen.
This button toggles between “Cornerstone” and “Keystone”.
When the test pattern is displayed, while pressing and holding
CTL, pressing this button displays a red test pattern.
NOTE: Pressing and holding this button for a minimum of two seconds will
reset 3D Reform correction setting values to zero.
22. AMPLITUDE (G)
Service personnel only.
When the test pattern is displayed, while pressing and holding
CTL, pressing this button displays a green test pattern.
23. ENTRY LIST (B)
Press to display the Entry List screen.
Pressing and holding CTL and then ENTRY LIST buttons si-
multaneously, enters a signal in the Entry List when you are
not displaying a test pattern.
When the test pattern is displayed, while pressing and holding
CTL, pressing this button displays a blue test pattern.
24. FOCUS (+/–)
While pressing and holding CTL, pressing this button allows
you to adjust the lens focus.
25. MAGNIFY/ZOOM (+/–)
Magnify the size of a target portion.
While pressing and holding CTL, pressing this button allows
you to zoom the lens in and out.
26. CTL
Used in conjunction with other buttons, similar to a shift key on
a computer.
27. Remote Jack
Connect your remote cable here for wired operation.
28. Infrared Transmitter
Direct the remote control toward the remote sensor on the pro-
jector cabinet.

1-12
1. Introduction
7m
30˚
30˚
Remote Control Precautions
•The remote control system may not function when direct sunlight or
strong illumination strikes the remote control sensor of the main unit, or
when there is an obstacle in the path.
•When remote control buttons are pressed and held, projector’s function
keys may not operate.
•Do not subject to strong shock.
•Do not allow water or other liquid to splash on the remote control. If the
remote control gets wet, wipe it dry immediately.
•Avoid exposure to heat and steam.
•Remove the batteries from the remote control when the remote control
is not going to be used for a long period.
Remote Control Battery Installation
Installing the Remote Control Batteries
When it comes time to replace the batteries, two "AAA" type will
be required.
1. Press and open the cover.
2. Align and insert the batteries according to the (+) and (-) indications
inside the case.
3. Replace the cover.
Operating Range for Wireless Remote Control
The infrared signal operates by line-of-sight up to a distance of
approximately 7m (20 feet) and a 60 degree angle of the remote
sensor.
The projector will not function if there are objects between the
remote sensor and the remote control or if strong light falls on
the remote sensor.Weak batteries will also prevent the projector
from operating properly.
Remote sensors on the
projector cabinet
Side View
7m
Remote control
NOTE: You cannot operate the projector using the remote control if:
• The remote control ID is not set to [None].
• The remote ID is not the same as the projector ID.
See page 7-2 for setting remote ID and projector ID.

1-13
AUDIO
AUDIO
AUDIO OUT
R
R/Cr
G/Y
B/Cb
V
H/
HV
R
L/MONO
R
L/MONO
R
L/MONO
L/MONO
SLOT 1 SLOT2
DVI
RGB OUT
RGB 1
RGB 2
VIDEO S-VIDEO
USB
(
MOUSE/HUB
)
USB
(
PC
)
PC CARD
2
1
PC CONTROL
IN
IN
OUT
OUT
SC TRIGGER REMOTE 2
REMOTE 1
LAN
AC IN
REMOTE 2
IN
OFF
+
-
PICTURE
ADJUST
ABC DEF GHI
JKL MNO PQR
STU
,. UNDO CANCEL
TEST
PICTURE
KEYSTONE AMPLITUDE ENTRYLIST
SOUND OSD
MUTE
MAGNIFY
HELPINFO.
POSITION AUTOPIXEL
VWX YZ /
WHITE BAL.
IMAGE
ON
POWER
MENU
ENTER
123
456
7
0
89
ADDRESS
PROJECTOR
R G B
LENS
SHUTTER
BS
+
-
+
-
FOCUS ZOOM
CTL
LENS
Using the Remote Control in Wired Operation
Connect one end of the supplied remote cable to the REMOTE 2 IN
mini jack and the other end to the remote jack on the remote control.
NOTE: Do not use this jack for anything other than intended use. Connecting the wired
remote control to the SC. TRIGGER Mini Jack causes damage to the remote control.
Te r minal panel (Right)
Remote cable (supplied)
1. Introduction

2-1
2
Installation
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
zSetting Up Your Projector .......................................... 2-2
Screen Size and Projection Distance .................................................................. 2-2
xLens Shift Adjustable Range ....................................2-4
cOptional Lens Installation .........................................2-6
vMaking Connections ................................................. 2-8
Connecting Your PC or Macintosh ....................................................................... 2-8
To connect Scart Output ................................................................................. 2-9
Connecting an External Monitor .......................................................................... 2-9
Connecting Your DVD Player ............................................................................. 2-10
Connecting Your VCR or Laser Disc Player ....................................................... 2-11
Connecting to a Network ................................................................................... 2-12
Connecting the Supplied Power Cable .............................................................. 2-13

2-2
List of Screen Sizes
Screen size Width (H) Height (V)
minch m inch
40" 0.8 31.5 0.6 23.6
60" 1.2 47.2 0.9 35.4
80" 1.6 63.0 1.2 47.2
100" 2.0 78.7 1.5 59.1
120" 2.4 94.5 1.8 70.9
150" 3.0 118.1 2.3 90.6
200" 4.1 161.4 3.0 118.1
250" 5.1 200.8 3.8 149.6
300" 6.1 240.2 4.6 181.1
400" 8.1 318.9 6.1 240.2
500" 10.2 401.6 7.6 299.2
Formulas: Screen width H (m)= Screen size4/50.0254
Screen height V (m)= Screen size3/50.0254
Screen width H (inch)= Screen size4/5
Screen height V (inch)= Screen size3/5
Width
Height Screen size (Diagonal)
Screen Size and Projection Distance
Applicable lens and throw distance/ List of screen sizes
This chapter describes how to set up your projector and how to connect video and audio sources.
zSetting Up Your Projector
Your Projector is simple to set up and use. But before you get started, you must first:
1. Determine the image size
2. Set up a screen or select a non-glossy white wall onto which you can
project your image.
3. Install the optional lens to the projector.
4. Connect the supplied power cable.
5. Set up the projector.
6. Connect a PC, VCR, DVD player, or other equipment.
7. Make settings or adjustments on the projector.
Table of Throw Distances and Screen Sizes for Optional Lenses
0.76
1.17
1.31
1.41
1.58
1.66
1.78
1.99
2.39
3.01
3.62
4.02
4.23
4.84
5.04
––
––
––
––
30.0
46.1
51.7
55.7
62.1
65.3
70.2
78.2
94.2
118.3
142.4
158.5
166.5
190.6
198.6
––
––
––
––
40"
60"
67"
72"
80"
84"
90"
100"
120"
150"
180"
200"
210"
240"
250"
270"
300"
400"
500"
(m)
(inches)
1.0
GT10RLB
(001-714)
GT19ZL (LA00232) GT20ZL
(001-710)
GT24ZLB
(001-712)
GT34ZLB
(001-713)
2. Installation
GT13ZLB
(001-711)
0.91 - 1.15
1.40 - 1.75
1.57 - 1.97
1.70 - 2.12
1.89 - 2.36
1.99 - 2.48
2.14 - 2.66
2.38 - 2.96
2.87 - 3.57
3.60 - 4.48
4.33 - 5.38
4.82 - 5.99
5.07 - 6.29
5.80 - 7.20
6.04 - 7.50
6.53 - 8.11
7.27 - 9.01
––
––
36.0 - 45.2
55.2 - 69.0
62.0 - 77.4
66.8 - 83.3
74.5 - 92.9
78.3 - 97.6
84.1 - 104.8
93.7 - 116.7
112.9 - 140.5
141.8 - 176.2
170.6 - 212.0
189.9 - 235.8
199.5 - 247.7
228.4 - 283.4
238.0 - 295.4
257.2 - 319.2
286.1 - 354.9
––
––
1.2-1.5
(m) (inches)
1.30 - 1.74
1.99 - 2.65
2.23 - 2.97
2.40 - 3.19
2.68 - 3.56
2.82 - 3.74
3.02 - 4.01
3.37 - 4.47
4.06 - 5.38
5.10 - 6.74
6.14 - 8.11
6.83 - 9.02
7.17 - 9.47
8.21 -10.84
8.56 -11.29
9.25 -12.20
10.28 -13.57
––
––
51.0 - 68.4
78.3 - 104.2
87.8 - 116.7
94.6 - 125.7
105.5 - 140.0
110.9 - 147.2
119.1 - 158.0
132.7 - 175.9
159.9 - 211.7
200.7 - 265.4
241.6 - 319.2
268.8 - 355.0
282.4 - 372.9
323.2 - 426.7
336.8 - 444.6
364.0 - 480.4
404.9 - 534.1
––
––
1.7-2.2
(m) (inches)
1.53 - 2.03
2.34 - 3.10
2.62 - 3.47
2.83 - 3.74
3.15 - 4.16
3.32 - 4.38
3.56 - 4.70
3.97 - 5.23
4.78 - 6.30
6.00 - 7.90
7.22 - 9.50
8.04 -10.56
8.44 -11.10
9.66 -12.69
10.07 -13.23
10.88 -14.29
12.10 -15.89
––
––
60.1 - 80.0
92.1 - 122.0
103.3 - 136.7
111.3 - 147.2
124.1 - 164.0
130.6 - 172.4
140.2 - 185.0
156.2 - 205.9
188.2 - 247.9
236.3 - 310.9
284.3 - 373.9
316.3 - 415.8
332.4 - 436.8
380.4 - 499.8
396.4 - 520.8
428.5 - 562.8
476.5 - 625.7
––
––
2.0-2.6
(m) (inches)
––
2.58 - 3.86
2.90 - 4.32
3.12 - 4.66
3.48 - 5.19
3.66 - 5.45
3.93 - 5.85
4.38 - 6.52
5.28 - 7.84
6.64 - 9.83
7.99 -11.83
8.89 -13.15
9.34 -13.82
10.69 -15.81
11.14 -16.47
12.04 -17.80
13.40 -19.79
17.90 -26.43
––
––
101.6 - 152.0
114.0 - 170.3
122.9 - 183.3
137.1 - 204.3
144.2 - 214.7
154.8 - 230.4
172.6 - 256.5
208.0 - 308.8
261.3 - 387.2
314.5 - 465.6
350.0 - 517.9
367.7 - 544.0
421.0 - 622.4
438.7 - 648.6
474.2 - 700.8
527.4 - 779.2
704.9 -
1,040.6
––
2.2-3.2
(m) (inches)
––
––
––
––
5.10 - 7.81
5.36 - 8.21
5.76 - 8.81
6.41 - 9.81
7.73 -11.81
9.71 -14.80
11.69 -17.80
13.01 -19.79
13.67 -20.79
15.64 -23.79
16.30 -24.78
17.62 -26.78
19.60 -29.78
26.19 -39.76
32.79 -49.74
––
––
––
––
200.6 - 307.6
211.0 - 323.3
226.6 - 346.9
252.5 - 386.2
304.5 - 464.8
382.3 - 582.7
460.2 - 700.6
512.1 - 779.2
538.1 - 818.5
615.9 - 936.5
641.9 - 975.8
693.8 -
1,054.4
771.7 - 1,172.3
1,031.2
- 1,565.3
1,290.8
- 1,958.4
3.2-4.8
(m) (inches)
(no memory function)