Digitus GreyRapid N User manual

GreyRapid N
Wireless Network Router
User’s Manual
(DN-7049-1 Version: 1.0)

COPYRIGHT
Copyright ©2008/2009 by this company. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system,
or translated into any language or computer language, in any form or by any means,
electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the
prior written permission of this company
This company makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Any software described in this
manual is sold or licensed "as is". Should the programs prove defective following
their purchase, the buyer (and not this company, its distributor, or its dealer) assumes
the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves the
right to revise this publication and to make changes from time to time in the contents
thereof without obligation to notify any person of such revision or changes.

Federal Communication Commission
Interference Statement
FCC Part 15
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This equipment must be installed and operated in accordance with provided
instructions and a minimum 20 cm spacing must be provided between computer
mounted antenna and person’s body (excluding extremities of hands, wrist and feet)
during wireless modes of operation.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for

compliance could void the authority to operate equipment.
Federal Communication Commission (FCC) Radiation Exposure
Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the FCC radio frequency
exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches)
during normal operation.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
The equipment version marketed in US is restricted to usage of the channels 1-11
only.

R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF
THE EUROPEAN PARLIAMENTAND THE COUNCIL of March 9, 1999 on radio
equipment and telecommunication terminal Equipment and the mutual recognition of
their conformity (R&TTE).
The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment)As
of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install
and use it. However, special attention must be paid to the dangers of electric shock
and static electricity when working with electrical equipment. All guidelines of this
and of the computer manufacture must therefore be allowed at all times to ensure the
safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria,
Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg,
the Netherlands, Portugal, Spain, Sweden, and the United Kingdom.
The ETSI version of this device is also authorized for use in EFTA member states:
Iceland, Liechtenstein, Norway, and Switzerland.
EU Countries Not intended for use
None.

CATALOG
CHAPTER I:PRODUCT INFORMATION
1-1 Introduction and safety information
1-2 Safety Information
1-3 System Requirements
1-4 Package Contents
1-5 Familiar with your new wireless broadband router
CHAPTER II: SYSTEM AND NETWORK SETUP
2-1 Build network connection
2-2 Connecting to wireless broadband router by web browser
2-2-1 W i ndows 95/98/Me IP address setup
2-2-2 W i ndows 2000 IP address setup
2-2-3 W i ndows XP IP address setup
2-2-4 W i ndows Vista IP address setup
2-2-5 Router IPaddress lookup
2-3 Using ‘Quick Setup’
2-3-1 Setup procedure for ‘Cable Modem’
2-3-2 Setup procedure for ‘Fixed-IP xDSL’
2-3-3 Setup procedure for ‘PPPoE xDSL’
2-3-4 Setup procedure for ‘PPTP xD S L ’
2-3-5 Setup procedure for ‘L2TP xDSL’
2-3-6 Setup procedure for ‘Telstra Big Pond’
2-4 Basic Setup
2-4-1 Time zone and time auto-synchronization
2-4-2 Change management password
2-4-3 Remote Management

2-5 Setup Internet Connection (WAN Setup)
2-5-1 Setup procedure for ‘Dynamic IP’
2-5-2 Setup procedure for ‘Static IP’
2-5-3 Setup procedure for ‘PPPoE’
2-5-4 Setup procedure for ‘PPTP’
2-5-5 Setup procedure for ‘L2TP’
2-5-6 Setup procedure for ‘Telstra Big Pond’
2-5-7 Setup procedure for ‘DNS’
2-5-8 Setup procedure for ‘DDNS’
2-6 Wired LAN Configurations
2-6-1 LAN IPsection
2-6-2 DHCP Server
2-6-3 Static DHCP Leases Table
2-7 Wireless LAN Configurations
2-7-1 Basic Wireless Settings
2-7-1-1 Setup procedure for ‘AP'
2-7-1-2 Setup procedure for ‘Station-Infrastructure'
2-7-1-3 Setup procedure for ‘AP Bridge - Point to Point’
2-7-1-4 Setup procedure for ‘AP Bridge - Point to Multi Point’
2-7-1-5 Setup procedure for ‘AP Bridge - WDS’
2-7-1-6 Setup procedure for ‘Universal Repeater'
2-7-2 Advanced Wireless Settings
2-7-3 Wireless Security
2-7-3-1 Disable wireless security
2-7-3-2 W E P - Wired Equivalent Privacy
2-7-3-3 W i -Fi Protected Access (WPA)
2-7-3-4 WPARADIUS
2-7-4 Wireless Access Control
2-7-5 W i -Fi Protected Setup (WPS)
2-7-6 Security Tips for Wireless Network

CHAPTER III:ADVANCED FUNCTIONS
3-1 Quality of Service (QoS)
3-1-1 Basic QoS Settings
3-1-2Add a new QoS rule
3-2 NetworkAddress Translation (NAT)
3-2-1 Basic NAT Settings (Enable or disable NAT function)
3-2-2 Port Forwarding
3-2-3 Virtual Server
3-2-4 Port Mapping for Special Applications
3-2-5 UPnP Setting
3-2-6 ALG Settings
3-3 Firewall
3-3-1 Access Control
3-3-1-1Add PC
3-3-2 URLBlocking
3-3-3 DoSAttack Prevention
3-3-3-1 DoS - Advanced Settings
3-3-4 Demilitarized Zone (DMZ)
3-4 System Status
3-4-1 System information and firmware version
3-4-2 Internet Connection Status
3-4-3 Device Status
3-4-4 System Log
3-4-5 Active DHCP client list
3-4-6 Statistics
3-5 Configuration Backup and Restore
3-6 Firmware Upgrade
3-7 System Reset

CHAPTER IV: APPENDIX
4-1 Hardware Specification
4-2 Troubleshooting
4-3 Glossary

1
Chapter I: Product Information
1-1 Introduction and safety information
Thank you for purchasing this wireless broadband router! This high
cost-efficiency router is the best choice for Small office / Home office
users, all computers and network devices can share a single xDSL / cable
modem internet connection at high speed. Easy install procedures allows
any computer users to setup a network environment in very short time -
within minutes, even inexperienced. When the number of your computers
and network-enabled devices grow, you can also expand the number of
network slot bysimple attach a hub or switch, to extend the scope of your
network!
All computers and IEEE 802.11b/g/Draft-N wireless-enabled network
devices (including PDA, cellular phone, game console, and more!) can
connect to this wireless router without additional cabling. W i t h a
compatible wireless card installed in your PC, you can transfer file for up
to 150Mbps (transfer data rate).
Other features of this router including:
•High Internet Access throughput
•Allow multiple users to share a single Internet line
•Supports up to 253 users
•Share a single Cable or xDSL internet connection
•Access private LAN servers from the internet
•Four wired LAN ports (10/100M) and one WAN port (10/100M)
•Work with IEEE 802.11b/g/Draft-N wireless LAN devices
•Support DHCP (Server/Client) for easy IP-address setup
•Support multiple wireless modes like:AP, Station-Infrastructure,
Wireless Bridge and Universal Repeater.
•Advanced network and security features like: Special Applications, QoS,
DMZ, Virtual Servers, Access Control, Firewall.
•Allow you to monitor the router’s status like: DHCP Client Log, System
Log, Security Log and Device/Connection Status

2
•Easy to use Web-based GUI for network configuration and
management purposes
•Remote management function allows configuration and upgrades from
a remote computer (over the Internet)
•Auto MDI / MDI-X function for all wired Ethernet ports.

3
1-2 Safety Information
In order to keep the safetyof users and your properties, please follow the
following safety instructions:
1. This router is designed for indoor use only; DO NOT place this router
outdoor.
2. DO NOTput this router at or near hot or humid places, like kitchen or
bathroom.Also, do not left this router in the car in summer.
3. DO NOTpull any connected cable with force; disconnect it from the
router first.
4. If you want to place this router at high places or hang on the wall,
please make sure the router is firmly secured. Falling from high places
would damage the router and its accessories, and warranty will be void.
5.Accessories of this router, like antenna and power supply, are danger to
small children under 3 years old. They may put the small parts in their
nose or month and it could cause serious damage to them. KEEP THIS
ROUTER OUT THE REACH OF CHILDREN!
6. The router will become hot when being used for long time (This is
normal and is not a malfunction).DO NOTput this router on paper,
cloth, or other flammable materials.
7. There’s no user-serviceable part inside the router. If you found that the
router is not working properly, please contact your dealer of purchase and
ask for help. DO NOT disassemble the router, warranty will be void.
8. If the router falls into water when it’s powered, DO NOT use your
hand to pick it up. Switch the electrical power off before you do anything,
or contact an experienced technician for help.
9. If you smell something strange, or even see some smoke coming out
from the router or power supply, remove the power supply or switch the
electrical power off immediately, and call dealer of purchase for help.

4
1-3 System Requirements
Internet connection, provided by xDSL or cable modem with a RJ-45
Ethernet port.
Computer or network devices with wired or wireless network interface
card.
Web browser (Microsoft Internet Explorer 4.0 or above, Netscape
Navigator 4.7 or above, Opera web browser, or Safari web browser).
An available AC power socket (100 – 240V, 50/60Hz)

5
1-4 Package Contents
Before you starting to use this router, please check if there’s anything
missing in the package, and contact your dealer of purchase to claim for
missing items:
□Broadband router (main body, 1 pcs)…………………………… 1
□Quick installation guide (1 pcs) ………………………………… 2
□User manual CDROM (1 pcs) ………………………………….. 3
□A/C power adapter (1 pcs) ……………………………………..... 4

6
1-5 Familiar with your new wireless broadband router
Front Panel
LED Name
Light Status
Description
PWR
On
Router is switched on and correctly powered.
WLAN
On
Wireless WPS function is enabled.
Off
Wireless network is switched off.
Flashing
Wireless LAN activity (transferring or
receiving data).
W A N
LNK/ACT
On
WAN port is connected.
Off
WAN port is not connected.
Flashing
WAN activity (transferring or receiving data).
LAN 1-4
LNK/ACT
On
LAN port is connected.
Off
LAN port is not connected.
Flashing
LAN activity (transferring or receiving data).

7
Back Panel
Item Name
Description
Antenna
It is 3dBi dipole antenna.
Radio ON/OFF
Switch the button to activate or deactivate the wireless functions.
Reset / WPS
Reset the router to factory default settings (clear all settings) or
start WPS function. Press this button and hold for 10 seconds to
restore all settings to factory defaults, and press this button for less
than 5 seconds to start WPS function.
1 - 4
Local Area Network (LAN) ports 1 to 4.
W A N
Wide Area Network (WAN / Internet) port.
Power
Power connector, connects to A/C power adapter.

8
Chapter II: System and Network Setup
2-1 Build network connection
Please follow the following instruction to build the network connection
between your new WIRELESS router and your computers, network
devices:
1. Connect your xDSL/ cable modem to theWAN port of router by
Ethernet cable.
2. Connect all your computers, network devices (network-enabled
consumer devices other than computers, like game console, or switch /
hub) to the LAN port of the rout e r .

9
3. Connect theA/C power adapter to the wall socket, and then connect it
to the ‘Power’socket of the router.
4. Please check all LEDs on the front panel. ‘PWR’ LED should be
steadily on, WAN and LAN LEDs should be on if the computer /
network device connected to the respective port of the router is
powered on and correctly connected. If PWD LED is not on, or any
LED you expected is not on, please recheck the cabling, or jump to
‘4-2 Troubleshooting’for possible reasonsand solution.

10
2-2 Connecting to wireless broadband router by web browser
After the network connection is built, the next step you should do is
setup the router with proper network parameters, so it can work properly
in your network environment.
Before you can connect to the router and start configuration
procedures, your computer must be able to get an IP address
automatically (use dynamic IP address). If it’s set to use static IP address,
or you’re unsure, please follow the following instructions to configure
your computer to use dynamic IP address:
If the operating system of your computer is….
Windows 95/98/Me - please go to section 2-2-1
Windows 2000 - please go to section 2-2-2
Windows XP - please go to section 2-2-3
Windows V i s t a - please go to section 2-2-4
2-2-1Windows 95/98/Me IP address setup:
1. Click ‘Start’button (it should be located at lower-left corner of your
computer), then click control panel. Double-click Network icon, and
Network window will appear. Select ‘TCP/IP’, then click ‘Properties’.

1 1
2. Select ‘Obtain an IP address from a DHCP server’and then click ‘OK’.