Digitus DN-95301 User manual

8-PORT POWER OVER ETHERNET
MANAGED WORKGROUP SWITCH
(DN-95301)
User Guide
Layer 2/2+ Management Switch Series 1
8-Port 100BaseTX + 2 Gigabit combo La er 2 Management Switch with 8 PSE port
embedded 100W PoE power budget

The information in this guide ma be changed without notice. The
manufacturer assumes no responsibilit for an errors which ma appear in
this guide.
Ethernet is a trademark of XEROX Corporation. Microsoft, Windows and
Windows logo are trademarks of Microsoft Corporation.
Cop right 2008. All right are reserved. No Part of the contents of this guide
ma be transmitted or reproduced in an form or b an means without the
written permission of us. Printed in Taiwan.
Version 1. e
FCC Statement
This product has been tested and found to compl with the limits for a Class A
digital device pursuant to Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against such interference when operating in a
commercial environment. This equipment generates uses and can radiate
radio frequenc energ , and if not installed and used according to the
instructions, ma cause harmful interference to radio communications.
Operation of this equipment in a residential area is likel to cause
interference, in which case the user, at his or her own expense will be
required to take whatever measures to correct the interference.
CE Mark Warning
This is a Class A product. In a domestic environment, this product ma cause
radio interference in which case the user ma be required to take adequate
measures.
Layer 2/2+ Management Switch Series 2

Table of Contents
1.1. Package Contents ..............................................................................5
1.2. How to Use this Guide ........................................................................5
1.1. Product Description Overview ............................................................ 6
1.2. Switch Front and Rear Panel ............................................................. 6
8-Port 100BaseTX + 2 Gigabit combo La er 2 Management Switch
with 8 PSE port embedded 100W PoE power budget ........................ 6
6
6
Power ........................................................... 6
6
1.3. LED Function ....................................................................................... 7
1.4. Reset Button ........................................................................................ 7
1.5. Installing the Switch ............................................................................. 7
2.1. Rack- Mount Placement......................................................................8
2.2. Preparing for configuration ..............................................................10
1.5.1. Connecting a PC or Terminal to the RS-232 Port ................. 10
1.5.2. Terminal Emulation Setup Program ....................................... 10
1.5.3. Logging on to the switch ........................................................ 11
1.6. Web-based configuration .................................................................. 11
1.6.1. Logging on the switch ............................................................. 11
1.7. Command Line Interface (b Console or Telnet) .............................. 11
1.7.1. Mode-based Command Hierarch .......................................... 11
1.7.2. User Mode commands ............................................................ 13
help 13
? 13
logout 13
ping 13
show 13
enable 14
1.7.3. Privileged Mode commands .................................................... 14
cable-diag...................................................................................14
clear 14
configuration...............................................................................15
cop 15
exit 15
help 15
logout 15
ping 16
reload 16
save 16
show 16
telnet 22
1.7.4. Global Config mode commands .............................................. 22
exit 22
vlan 22
bridge 23
lacp-s spri..................................................................................23
Layer 2/2+ Management Switch Series 3

link-aggregation.........................................................................24
lldp 24
log 25
radius-server..............................................................................25
static-address.............................................................................25
mgmt-accesslist.........................................................................26
monitor 26
dot1x 26
network 27
port-all 28
qos 29
set 30
snmp 32
sntp 33
spanning-tree ............................................................................34
User 36
Interface 36
rmon 36
access list ..................................................................................36
arp 39
dos 39
tacplus 40
green-eth 41
1.7.5. Interface Config mode commands .......................................... 41
exit 41
dot1x 41
lacp 41
addport 41
delport 41
lldp 41
admin-mode...............................................................................42
auto-negotiate .......................................................................42
speed 42
flow-control.................................................................................43
port-securit ..............................................................................43
qos 43
rate-limit 43
storm-control..............................................................................43
rmon-counter..............................................................................44
set igmp-router-port ..................................................................44
spanning tree.............................................................................44
vlan 45
poe 45
1.8. Cable specifications .......................................................................... 47
1.9. Technical Specifications ................................................................... 49
1.9.1. Software Specification ............................................................. 49
1.9.2. Hardware Specification ........................................................... 50
1.9.3. Environments Specification
50
1.9.4. Standard Conformance ........................................................... 50
Layer 2/2+ Management Switch Series 4

1. Introduction
Thank ou for choosing La er 2/2+ series Management Switch. These
switches are cost-effective switching solution idea for small business and the
network edge. It provides the Qualit of Service (QoS) features, like 802.1p,
DSCP and Rate Control etc, to ensure the traffic is prioritized properl to
deliver real-time applications like voice and video and also have a good
control in network bandwidth usage. The 802.1Q feature enables ou
separate the network traffic easil and quickl . The Network Securit features,
like ACL, Port Securit , Storm Control, 802.1X and Management IP List etc,
enables ou to prevent unauthorized access to compan network and block
intentional or inadvertent network traffic. The Spanning Tree Protocol (STP)
provides ou a loop-free network. The IGMP snooping enables ou to have
efficient network usage in IP multicast environment. The one-to-one or man -
to-one Port Mirroring feature of the switch enables ou to monitor the traffic on
the network. With these features, ou can build or expand our network
quickl and easil .
1.1.Package Contents
These L2 Management Switches package contains the following:
> One L2 Management Switch
> One RS-232 cable
> One power cord/adapter
> One set of brackets.
> One CD for user manual and utilities.
If an of the listed items is missing or damaged, please contact the place of
purchase.
1.2.How to Use this Guide
This user guide is structured as follows:
Chapter 2, Installation explains the functions of the switch and how to
ph sicall install it.
Chapter 3, Configuration explains how to set up and modif the configuration
of the switch.
Chapter 4, Specifications contains information about the cables, and the
technical specifications of the switch.
Appendices include the Warrant Statement. Read them as
necessar .
Layer 2/2+ Management Switch Series 5

2. Installation
This chapter describes the function of the management switch components
and shows how to install it on the desktop or shelf. Basic knowledge of
networking is assumed. Read this chapter completel before continuing.
1.1.Product Description Overview
These product is a L2 management switch which supports 802.1Q VLAN,
QoS, 802.1d / 1w/ 1s Spanning Tree Protocol, 802.1x, Port Securit , Port
Mirroring, IGMP Snooping, SNTP, Storm Control, Rate Control, SNMP etc.
features.
1.2.Switch Front and Rear Panel
8-Port 1 BaseTX + 2 Gigabit combo Layer 2 Management Switch with 8 PSE
port embedded 1 W PoE power budget
The front panel of this switch has 8 10/100 Mbps copper ports at the left with
2 shared Gigabit SFP slots at the right. The product name indicates at the top
on the right. Figure 2.2.6a shows a front panel of the switch. The rear panel
has a power and console connector, and Figure 2.2.6b shows a rear panel of
the switch. Table 2.2.6c shows the port function of the switch.
Figure 2.2.6a Front Panel
Figure 2.2.6b Rear Panel
Power
Table 2.2.6c Port Function
Port Function
Power This is where ou connect the DC power adapter.
Layer 2/2+ Management Switch Series 6

1.3.LED Function
This section explains the definition of the Switch’s LEDs on the front panel.
8-Port 1 BaseTX + 2 Gigabit combo Layer 2 Management Switch with 8 PSE port
embedded 1 W PoE power budget :
PWR (Green) LED lights up, it shows the s stem is powered up.
Link/Act (Green) LED lights up, it indicates a successful connection of that
port is established. Otherwise, it indicates the link is off or
no-link detected of that port. When the LED blinks, it
indicates the port is activating and transmitting data;
PoE (Amber) LED lights up onl when the corresponding port suppl power.
1.4.Reset Button
There is a Reset button on the front panel, which has two functionalities:
a) To restore switch configuration to factor defaults
Press the Reset button for more than 10 seconds, switch configuration will
be restored to factor defaults and then reboots.
b) To reboot switch
Press the Reset button for less than 10 seconds, switch will reboot.
Please note, ou will lose unsaved change when doing this.
1.5.Installing the Switch
This section describes how to install and make connection to our Managed
Switch. The following diagram shows the a t pical network configuration,
Figure shows the network configuration for L2/L2+ Management Switch with
PoE function.
Figure 2.5.2 Network Configuration for L2 Management Switch with PoE
Layer 2/2+ Management Switch Series 7

Read and perform the following procedures to install the switch,
Pre-Installation Considerations
Gigabit Considerations:
If ou will use the switch for Gigabit applications, keep in mind that the
maximum UTP cabling length of Categor 5e cable is 328 feet (100 meters).
Positioning the switch:
When choosing a location for the switch, observe the following guidelines:
Keep enough ventilation space between the switch and the surrounding
objects.
Keep cabling awa from sources of electrical noise, power lines, and
fluorescent lighting fixtures.
Do not stack free-standing switch more than four units high.
Desktop or Shelf Mounting
To install the switch on a desktop or shelf, simpl complete the following
steps:
Step 1 Place the switch on a desktop or shelf near an AC power source.
Step 2 Keep enough ventilation space between the switch and the
surrounding objects.
Note: When choosing a location, keep in mind the environmental restrictions
discussed in Chapter 4, Specifications.
Step 3 Connect the switch to network devices.
A. Connect one end of a standard network cable to the RJ-45 ports on the
front of the switch.
B. Connect the other end of the cable to the network devices such as printer
servers, workstations or routers.
Note: It is recommended to use the UTP Categor 5e network cabling with
RJ-45 tips for the network connection. For more information, please
see the Cable Specifications in Chapter 4, Specifications.
Step 4 Suppl power to the switch.
A. Connect one end of the power cable to the switch.
B. Connect the power cube end of the power cable to a standard wall outlet.
2.1.Rack- Mount Placement
Before mounting the Switch, please read the following instructions carefull ,
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack
assembl , the operating ambient temperature of the rack environment ma
be greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified b the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
Layer 2/2+ Management Switch Series 8

not compromised.
C) Mechanical Loading - Mounting of the equipment in the rack should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.
D) Circuit Overloading - Consideration should be given to the connection of
the equipment to the suppl circuit and the effect that overloading of the
circuits might have on overcurrent protection and suppl wiring.
Appropriate consideration of equipment nameplate ratings should be used
when addressing this concern.
E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be
maintained. Particular attention should be given to suppl connections
other than direct connections to the branch circuit (e.g. use of power
strips)."
To mount the Switch in an standard-sized, 19-inch wide, 1U high rack,
please follow these instructions:
Place the Switch on a hard flat surface with the front panel facing ou.
Attach a rack–mount bracket to one side of the Switch with the supplied
screws. Then attach the other bracket to the other side. (Figure 2.6.1)
Figure 2.6.1
Make sure the brackets are properl attached to the Switch.
Use the appropriate screws (not included) to securel attach the brackets to
our rack. (Figure 2.6.2)
Figure 2.6.2
Layer 2/2+ Management Switch Series 9

Configuration
The configuration programs are supplied with these La er 2 Management
Switches. Unlike the unmanaged switch (dumb switch), the switch performs
"management" functions that make the switch operate more effectivel . This
Chapter will describe the use of the switch Management Configuration
program.
2.2. Preparing for configuration
La er 2 Management Switch offers a console CLI interface for switch
configuration and management. Users can use this interface to perform the
activities such as configuring DHCP, ARP, assigning IP address and
upgrading firmware etc.
There are four methods to manage our switch:
Local Console Management
You can manage the switch locall b connecting the switch to a PC or
workstation with terminal emulation software using the serial port.
Remote Console Management
You can manage the switch b having a remote host establish a Telnet
connection to the switch via an Ethernet or modem link.
SNMP Management
You can manage the switch across a LAN using an SNMP Network
Management Station with a graphical user interface. Note that to use this
management method, our network must use the IP protocol and our switch
must be configured on the Network with a proper IP address. You ma use
an of the following method to manage the switch.
Web-Browser
You can manage the switch through a web connection b connecting to the
switch’s IP address using our web browser.
This User Guide provides instructions on how to configure the switch using
the console interface. Read the following sections to start up!
1.5.1.Connecting a PC or Terminal to the RS-232 Port
When ou are read to configure the Management Function of the switch,
make sure ou have connected the supplied RS-232 serial cable to the RS-
232 port at the front panel of our switch and our PC.
1.5.2.Terminal Emulation Setup Program
Run a terminal emulation program with the following setting.
Emulation: VT-100 compatible
Baud per second: 38400
Data bits: 8
Parity: None
Stop bits: 1
Layer 2/2+ Management Switch Series 10

Flow Control: None
1.5.3.Logging on to the switch
Enter the factor default user name “admin” with no password when logging
on to the switch. The password is set to be empt . If ou can enter “?” on the
command line screen, it will displa all items so that ou can configure b our
requirements.
1.6.Web-based configuration
The Switch provides a Web-based interface for configuring and managing the
Switch. This interface allows ou to access the switch using the Web browser
of our choice. This chapter describes how to use the switch’s Web browser
interface to con-figure and manage the switch.
1.6.1.Logging on the switch
To log on to the Switch:
1. In our web browser, specif the IP address of the switch. Default IP
address is 192.168.1.254.
2. Enter the factor default “admin “to login on the Switch with no password.
Refer to the figure 3-1.
Figure 3-1
1.7.Command Line Interface (by Console or Telnet)
1.7.1.Mode-based Command Hierarchy
The Command Line Interface (CLI) groups all the commands in appropriate
modes b the nature of the commands. Examples of the CLI command modes
are described below. Each of the command modes supports specific switch’s
Layer 2/2+ Management Switch Series 11

commands.
The CLI Command Modes table captures the command modes, the prompts
visible in that mode and the exit method from that mode.
Table 1 CLI Command Modes
Command
Mode Access Method Prompt Exit or Access Previous Mode
User Mode
This is the first
level of access.
Perform basic
tasks and list
s stem
information.
COMMAND> Enter Logout
command
Privileged
Mode
From the User
Mode, enter the
enable command.
Switch#
To exit to the User
Mode, enter exit or
Logout.
Global
Config Mode
From the
Privileged Mode,
enter the
configuration
command.
Switch (Config)#
To exit to the
Privileged Mode,
enter the exit
command.
Interface
Config Mode
From the Global
Config mode, enter
the interface
<port#> command.
Switch (Interface <port#>)#
To exit to the Global
Config mode, enter
exit.
The CLI is divided into various modes. The commands in one mode are not
available until the operator switches to that particular mode. The commands
available to the operator at an point in time depend upon the mode. Entering
a question mark (?) at the CLI prompt, and displa s a list of the available
commands and descriptions of the commands.
The CLI provides the following modes:
User Mode
When the operator logs into the CLI, the User Mode is the initial mode. The
User Mode contains a limited set of commands. The command prompt shown
at this level is:
Command Prompt: COMMAND>
Privileged Mode
To have access to the full suite of commands, the operator must enter the
Privileged Mode. The Privileged Mode requires password authentication.
From Privileged Mode, the operator can issue an Exec command to enter
the Global Configuration mode. The command prompt shown at this level is:
Command Prompt: Switch#
Global Config Mode
This mode permits the operator to make modifications to the running
configuration. General setup commands are grouped in this mode. From the
Global Configuration mode, the operator can enter the Interface Configuration
mode. The command prompt at this level is:
Command Prompt: Switch(Config)#
Layer 2/2+ Management Switch Series 12

From the Global Config mode, the operator ma enter the following
configuration modes:
Interface Config Mode
Man features are enabled for a particular interface. The Interface commands
enable or modif the operation of an interface. In this mode, a ph sical port is
set up for a specific logical connection operation. The command prompt at this
level is:
Command Prompt: Switch(Interface <port#>)#
1.7.2.User Mode commands
help
This command displa s help information
Format help
Mode User Mode
?
This command displa s help information
Format help
Mode User Mode
logout
This command is used to exit from the telnet
Format logout
Mode User Mode
ping
This command sends echo messages.
Format ping <A.B.C.D>
Mode User Mode
show
1) show port
This command displa s port status.
Format show port {<port#> | all}
Mode User Mode
2) show network
This command displa s switch IP configuration
Format show network
Mode User Mode
3) show s stem
This command displa s s stem information.
Format show s stem
Mode User Mode
4) show port statistics
This command displa s port statistics.
Format show port statistics {<port#> | all}
Mode User Mode
Layer 2/2+ Management Switch Series 13

enable
Enter to the Privileged Mode
Format enable
Mode User Mode
1.7.3.Privileged Mode commands
cable-diag
This command is used to proceed cable diagnostic
Format cable-diag port <port ID>
Mode Privileged Mode
e.g. Switch#cable-diag port 1
clear
1) clear arl
This command is used to clear ARL table entries
Format clear arl
Mode Privileged Mode
2) clear arl d namic
This command is used to Clear d namic arl table entries
Format clear arl d namic
Mode Privileged Mode
3) clear arl static
This command is used to clear static arl table entries
Format clear arl static mac <mac-addr>
Mode Privileged Mode
4) clear config
This command is used to restore switch factor default configuration
Format clear config
Mode Privileged Mode
5) clear counters
This command is used to clear RMON statistics for entire switch
Format clear counters
Mode Privileged Mode
6) clear igmpsnooping
This command is used to restore igmpsnooping configuration to factor
default
Format clear igmpsnooping
Mode Privileged Mode
7) clear static-mcast
This command is used to clear static multicast groups
Format clear static-mcast
Mode Privileged Mode
8) clear pass
This command is used to restore administrator’s password to factor default
Format clear pass
Mode Privileged Mode
9) clear lacp
Layer 2/2+ Management Switch Series 14

This command is used to restore LAG and LACP configuration to factor
default
Format clear lacp
Mode Privileged Mode
10) clear logs
This command is used to clear memor /flash logs
Format clear logs
Mode Privileged Mode
11) clear vlan
This command is used to delete all VLAN groups
Format clear vlan
Mode Privileged Mode
configuration
Enter into Global Configuration mode
Format configuration
Mode Privileged Mode
copy
This command is used to upload file from switch to host, or download file to
switch from host
1) cop nvram_config
This command is used to backup switch configuration
Format cop nvram_config tftp <A.B.C.D> file < ilename>
Mode Privileged Mode
e.g. Switch#cop nvram_config tftp 192.168.1.100 file switch_configuration
2) cop s stem_image
This command is used to backup switch runtime image
Format cop s stem_image tftp <A.B.C.D> < ilename>
Mode Privileged Mode
e.g. Switch#cop s stem_image tftp 192.168.1.100 image_file
3) cop tftp
This command is used to upload configuration or runtime image
Format cop tftp <A.B.C.D> file < ilename> {nvram_config |
s stem_image}
Mode Privileged Mode
e.g. Switch#cop tftp 192.168.1.100 file switch_configuration nvram_config
Switch#cop tftp 192.168.1.100 file runtime_code s stem_image
exit
This command is used to exit current shell
Format exit
Mode Privileged Mode
help
This command displa s help information
Format help
Mode Privileged Mode
logout
This command is used to exit current shell
Layer 2/2+ Management Switch Series 15

Format logout
Mode Privileged Mode
ping
This command is used to proceed ping destination host
Format ping <A.B.C.D>
Mode Privileged Mode
reload
This command is used to reboot s stem
Format reload
Mode Privileged Mode
save
This command is used to save configuration
Format save
Mode Privileged Mode
show
This command is used to show configured data
1) show qos
This command displa class of service information
1.1) show qos cos
This command displa the cos mapping
Format show qos cos
Mode Privileged Mode
1.2) show qos queue-settings
This command displa the queue-settings mapping
Format show qos queue-settings
Mode Privileged Mode
1. 3) show qos advanced
This command displa qos advanced mode information
1.3.1) show qos advanced mode
This command displa mode of qos
Format show qos advanced mode
Mode Privileged Mode
1.3.2) show qos advanced dscp
This command displa qos dscp mapping
Format show qos advanced dscp
Mode Privileged Mode
1.3.3) show qos advanced ip-precedence
This command displa qos ip precedence mapping
Format show qos advanced ip-precedence
Mode Privileged Mode
1.4) show qos port-based
This command is used to displa class of service information
1.4.1) show qos port-based port
This command displa class of service information
Format show qos port-based port <port-ID>
Mode Privileged Mode
1.4.2) show qos port-based all
Layer 2/2+ Management Switch Series 16

This command displa all switch interfaces’ cos settings
Format show qos port-based all
Mode Privileged Mode
2) show dot1x
This command displa dot1x information
2.1) show dot1x config
This command displa dot1x and port configuration
Format show dot1x config
Mode Privileged Mode
2.2) show dot1x radius
This command displa radius configuration
Format show dot1x radius
Mode Privileged Mode
2.3) show dot1x statistics
This command displa dot1x statistics
Format show dot1x statistics
Mode Privileged Mode
3) show igmp snooping
This command displa IGMP snooping information
3.1) show igmp snooping d namic_router_port
This command displa d namic router ports information
Format show igmp snooping d namic_router_port
Mode Privileged Mode
3.2) show IGMP snooping groups
This command is used to displa igmp groups information
Format show IGMP snooping groups
Mode Privileged Mode
4) show interface
This command is used to displa summar statistics
4.1) show interface histor
This command is used to displa port RX and TX
Format show interface histor <port-ID>
Mode Privileged Mode
4.2) show interface statistics
This command is used to displa port summar statistics
Format show interface statistics <port-ID>
Mode Privileged Mode
5) show lag
This command is used to displa link aggregation groups information
5.1) show lag lag-index
This command is used to specif an switch lag
Format show lag lag-index <port-ID>
Mode Privileged Mode
5.2) show lag all
This command is used to displa all switch lag
Format show lag all <port-ID>
Mode Privileged Mode
6) show lldp
This command is use to displa lldp statistics
6.1) show lldp statistic
This command is used to displa lldp statistic
Layer 2/2+ Management Switch Series 17

Format show lldp statistic
Mode Privileged Mode
6.2) show lldp local
This command is used to displa local information
Format show lldp local
Mode Privileged Mode
6.3) show lldp msap
This command is used to displa msap information
Format show lldp msap
Mode Privileged Mode
6.4) show lldp msap-entr
This command is used to displa msap details information
Format show lldp msap-entr <1..26>
Mode Privileged Mode
7) show logging
This command is used to displa trap records
7.1) show logging memor -log
This command displa memor log
Format show logging memor -log
Mode Privileged Mode
7.2) show logging flash-log
This command displa flash logs
Format show logging flash-log
Mode Privileged Mode
8) show monitor
This command is used to displa port mirroring settings
Format show monitor
Mode Privileged Mode
9) show network
This command is used to configuration for inband connectivit
Format show network
Mode Privileged Mode
10) show port
This command is used to displa port mode and settings, displa port status
10.1) show port port-index
This command is used to specif an switch interface
Format show port port-index <port-ID>
Mode Privileged Mode
10.2) show port all
This command is used to displa all switch interface
Format show port all
Mode Privileged Mode
11) show port-securit
This command is used to displa port securit settings
11.1) show port-securit port
This command is used to specif an switch interface
Format show port-securit port <port-ID>
Mode Privileged Mode
11.2) show port-securit all
This command is used to displa all interfaces’ status
Format show port-securit all
Layer 2/2+ Management Switch Series 18

Mode Privileged Mode
12) show rate-limit
This command is used to ingress and egress rate limit information
12.1) show rate-limit port
This command is used to specif an switch interface
Format show rate-limit port <port-ID>
Mode Privileged Mode
e.g. Switch#Show rate-limit port 1
Switch#Show rate-limit port g1
12.2) show rate-limit all
This command is used to displa all interfaces’ status
Format show Rate-Limit all
Mode Privileged Mode
13) show running-config
This command is used to displa switch running config
Format show running-config
Mode Privileged Mode
14) show snmp
This command is used to displa all snmp config
14.1) show snmp groups
This command displa all snmp groups
Format show snmp groups
Mode Privileged Mode
14.2) show snmp users
This command displa all snmp users
Format show snmp users
Mode Privileged Mode
3) show snmp communities
This command displa all snmp communities
Format show snmp communities
Mode Privileged Mode
15) show sntp
This command is used to displa switch sntp information
Format show sntp
Mode Privileged Mode
16) show spanning-tree
This command displa s Spanning Tree information
16.1) show spanning-tree interface
This command displa s RSTP ports information
16.1.1) show spanning-tree interface port
This command specif an switch interface
Format show spanning-tree interface port<port-ID>
Mode Privileged Mode
16.1.2) show spanning-tree interface all
This command displa all switch interface
Format show spanning-tree interface all
Mode Privileged Mode
16.2) show spanning-tree mst
This command displa MST information
16.2.1) show spanning-tree mst detailed
This command displa a MST instance information
Layer 2/2+ Management Switch Series 19

Format show spanning-tree mst detailed <0..4094>
Mode Privileged Mode
16.2.2) show spanning-tree mst instance
This command displa ports information on a MST instance
Format show spanning-tree mst instance <0..4094>
Mode Privileged Mode
16.2.3) show spanning-tree mst summar
This command displa all MST instance information
Format show spanning-tree mst summar
Mode Privileged Mode
16.2.4) show spanning-tree status
This command is used to displa spanning-tree status
Format show Spanning-tree status
Mode Privileged Mode
17) show storm-control
This command is used to displa storm-control information
Format show storm-control
Mode Privileged Mode
18) show s sinfo
This command is used to displa s stem information including s stem up
time
Format show s sinfo
Mode Privileged Mode
19) show switch
This command is used to displa switch information
19.1) show switch admin-time
This command displa the age time of web and console
Format show switch admin-time
Mode Privileged Mode
19.2) show switch age-time
This command displa the age time of L2 table
Format show switch age-time
Mode Privileged Mode
19.3) show switch mac-table
This command is used to displa address resolution protocol cache
Format show switch mac-table
Mode Privileged Mode
19.4) show switch mcast-table
This command displa multicast address table
Format show switch mcast-table
Mode Privileged Mode
20) show trapflags
This command is used to displa the value of trap flags that appl to the
switch
Format show trapflags
Mode Privileged Mode
21) show vlan
This command is used to displa vlan configuration
21.1)show vlan member
This command displa vlan configuration
Format show vlan member <1..4094>
Layer 2/2+ Management Switch Series 20