Dimplex B075E User manual

Installation and Operating Instructions
MARK1 Oil Filled Panel
(IPX0)
08/53912/0 Issue 1
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Model(s) Watt A B C D
B075E 750 570mm 659mm 405mm 527mm
C100E 1000 840mm 659mm 675mm 527mm
D150E 1500 1105mm 659mm 940mm 527mm
E200E 2000 1373mm 659mm 1208mm 527mm
75mm (min)
‘A’
‘B’
150mm
(min)
150mm
(min)
305mm
(min)
Shelf
Minimum
front
clearance
300mm
(min)
‘C’
‘D’
Dimensions
IMPORTANT SAFETY ADVICE
This appliance can be used by children aged
from 8 years and above and persons with
reducedphysical,sensoryor mentalcapabilities
or lack of experience or knowledge if they
have been given supervision or instruction
concerning the use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
Children of less than 3 years should be kept
away unless continuously supervised. Children
aged from 3 years and less than 8 years shall
only switch on/off the appliance provided that
it has been placed or installed in its intended
normal operating position and they have been
given supervision or instruction concerning
the use of the appliance in a safe way and
understand the hazards involved. Children
aged from 3 years and less than 8 years shall
not plug in, regulate and clean the appliance
or perform user maintenance.
CAUTION: Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and
vulnerable people are present.
WARNING: In order to avoid overheating, do
not cover the heater.
DO NOT use this heater in the immediate
surroundings of a bath, a shower or a swimming
pool.
CAUTION - In order to avoid a hazard due to
inadvertent resetting of the thermal cutout,
this appliance must not be supplied through
an external switching device, such as a timer
or connected to a circuit that is regularly
switched on and off by the utility
IMPORTANT - If the supply cord is damaged,
it must be replaced by the manufacturer, its
service agent or similarly qualied persons in
order to avoid a hazard.
This heater is lled with a precise quantity of
special oil. Repairs requiring the opening of
the oil container are only to be made by the
manufacturer or service agent who should be
contacted if there is an oil leak.
When scrapping the heater, follow the regulations
concerning the disposal of oil.
DO NOT COVER THE RADIATOR or place
material or gaments on it, or obstruct the air
circulation around the radiator, for example
with the curtains or funiture, as this could cause
overheating and a re risk.
The radiator complies with stringent safety
standards but to ensure efcient operation
SURFACES OF THE RADIATOR WILL BECOME
HOT AND CONTACT WITH THESE AREAS
SHOULD BE AVOIDED.
If young chiuldren, the aged or inrm are likely
to be left in the vicinity of the heater, we advise
that adequate precautions should be taken. We
recommend that a guard be tted to ensure
contact with the heater is avoided and objects
cannot be inserted into the product.
For further information, please contact our guard
supplier direct on Tel. No. 020 7987 1184, or in
case of difculty or for further advice contact
the Customer Helpline.
DO NOT use the radiator if it has been dropped or
damaged or the mains lead has been damaged,
until it has been examined by a qualied engineer.
DO NOT use the radiator if it develops an oil
leak. Unplug the radiator and contact your
supplier or our Customer Help Line.
Fig. 1

93mm
67mm
Energy Related Product Directive
Type of heat output/ room temperature control
With electronic room temperature control Yes
Electronic room temperature control plus week
timer Yes
With open window detection Yes
With adaptive start control Yes
Model Identier(s): B075E C100E D150E E200E
Nominal heat
output Pnom 0.75 kW 1 kW 1.25 kW 1.5 kW
Height (mm) 659 659 659 659
Width (mm) 570 840 1105 1373
Depth (mm) 50 50 50 50
Minimum heat
output (indicative) Pmin 0.75 kW 1.00 kW 1.25 kW 1.5 kW
Maximum continu-
ous heat output
Pmax-
,c 0.75 kW 1.00 kW 1.25 kW 1.5 kW
Auxiliary electricity Consumption
At nominal heat
output elmax 0.00 0.00 0.00 0.00
At minimum heat
output elmin 0.00 0.00 0.00 0.00
In standby mode elSB <0.0005 <0.0005 <0.0005 <0.0005
With open window detection Yes
With adaptive start control Yes
This product complies with Lot20 of the Energy Efciency Directive (2015/1188)
General Information
Please read the instructions closely before rst using the product.
This heater may be used wall-mounted or freestanding. The necessary wall
mounting brackets are provided with the product as a standard. The feet screws
can be bought seperately as an accessory.
It should only be operated when in the upright position as shown - see Fig.1a and
Fig.1b. All models are splash proof to IPX0. Before connecting the heater check
that the supply voltage is the same as that stated on the heater.
Wall Mounting
IMPORTANT - The radiator must only be mounted using the kit
supplied
WARNING - This product is heavy and care should be taken in
installation
Select a suitable position on a wall, near to a mains power outlet. The radiator
should not be mounted closer than 75mm from the oor - see Fig. 2 (to enable
cleaning), or adjacent side walls. Ensure at least 305mm clear space between
the radiator and any overhanging shelf. It should not be mounted closer than 1
metre from the ceiling.
NOTE - The bottom of the radiator must not be less than 75mm
from the lor. To achieve thism the top edge of the bottom
brackets must be at least 160mm from the oor - see Fig 2. On
this line, mark off the xing centres according to model - see ‘C’
in the table in Fig. 2 and Fig.3
Place the bottom brackets centrally over these centres with the top row of holes
on the line, and mark the xing hole positions – see Fig. 3.
STEP 3: Drill the holes and t wall plugs. Screw the bottom brackets in
position
– see Fig. 3.
STEP 4: Measure dimension D in Fig. 2 according to model, from the top of the
bottom brackets and draw a horizontal line. Mark off the xing centres
for the top brackets in line with the bottom brackets. Place each top
bracket on the line and mark the xing holes – see Fig. 4. Drill and plug
the wall and x the top brackets in place.
STEP 5: Place the radiator on the bottom brackets, then t each securing bracket
to the top of the radiator and secure it with the self-tapping screw
provided – see Fig. 5.
Check that the radiator is securely xed to the wall.
75mm
(min)
‘C’
‘Y’
75mm
(min)
Fig. 2
Fig. 3
Fig. 4 Fig. 5
STEP 1: Check that you have all the necessary components:
(a) 2 x Bottom Wall brackets
(b) 2 x Top Wall Brackets
(c) 2 x Radiator Securing Brackets
(d) 2 x Screws Self-tapping.
STEP 2: Using a straight edge, draw a horizontal line (see ‘Y’ in Fig. 2) for the
bottom brackets at the required mounting height from the oor.
This guide is for quick reference only
To view the full manual, please scan this QR code
using your smarphone or visit the product page at
www.dimplex.co.uk

IMPORTANT: Please register your product without delay. Simply scan this QR code using your smartphone, or go to
https://www.dimplex.co.uk/register.
If you do not have access to the internet, pelase call us on 0344 879 3588
Quick Start Guide
How does the heater control work?
The control allows you to choose when you want heat and at what temperature. When using a timer mode (see below) will display on the home screen to tell
you when the heater is maintaining the temperature displayed. The current time will be displayed when the heater is outside of a timed heating period.
When Manual, Schedule or Frost modes are being used the heater will always maintain the temperature shown on the home screen.
Set the Time
To set the date and time on the heater, press Menu, then press Up three times to highlight the Date & time Icon, press Enter. Use the Down and Up to increase/
decrease the hour, press Enter to conrm. Repeat this process to set the minutes, Day, Month and Year. Press Enter to conrm and return to home screen.
Set the Temperature
The temperature shown on the display is the target room temperature known as Setpoint. This is the temperature that the heater will maintain during the heating
periods. If the room temperature is above this temperature then the heater will not operate. The heater leaves the factory with this temperature set at 21oC which
represents a typical comfortable room temperature. If you require a different room temperature then press either Down or Up until the display shows the temperature
you require
Your heater comes pre-programmed with four heating periods. These periods set the time and temperature at which the heater operates in Comfort ON mode.
These four periods are:
• P1: 07:00 – 09:00 21oC
• P2: 10:00 – 12:00 7oC
• P3: 13:00 – 15:00 7oC
• P4: 17:00 – 21:00 21oC
Child Lock
If you need to lock the controls so that the settings cannot be changed then activate the Child Lock. To lock the controls press and hold both the Back button and
Enter button together for 3 seconds. The Lock icon will appear on the screen. To unlock repeat the action by pressing both the Back button and Enter for three
seconds.
Advance
Sometimes you may be at home when you had not planned to be or need to leave when you had planned to have heating on. You can change the way you use
your heating temporarily; this temporary change is achieved using the Advance function.
When a timer has been selected, the Advance function allows you to begin the next period early. If the heater is in a Comfort Off period and you want heat - press
the Advance button. The Advance icon will be displayed on the screen. If the heater is in the Comfort On and you don’t want heat, press the Advance button
and it will go off until the beginning of the next Comfort On Period.
The controls are located on the top of the heater. The heater is tted with an adjustable electronic controller consisting of a display screen and six touch sensitive
buttons:
DO NOT COVER
4 5 7321 986
1Back Button
2Menu Button
3Advance Button
4Up & Down
5Enter
6Indicator “ON”
7Days of the Week
8Display Screen
9Indicator “OFF”
Lock
Connectivity
Sound
Open Window
Adaptive Start
Manual Mode
Advance
Set Time & Date
Frost Protect
Schedule

Recycling
Your Guarantee
For electrical products sold within the European Community. At the end of the electrical product’s useful life it should not be
disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling
advice in your country. Batteries should be disposed of or recycled in accordance with WEEE Directive 2012/19/EU. Packaging
should be recycled where possible.
Your Product is manufactured by Glen Dimplex UK operating as Glen Dimplex Heating & Ventilation. GDHV designs and manufactures products
to ensure they deliver reliable service for normal use in domestic dwellings and, where specied by us, in light commercial premises.
GDHV products are individually tested before leaving the factory, Your product comes with a 2 year parts and labour guarantee for repair or
replacement of faulty goods and/or partial refund in the event that a repair or replacement is not available.
Your guarantee is provided by Glen Dimplex UK Ltd operating as Glen Dimplex Heating & Ventilation Ltd, Millbrook House, Grange Drive,
Southampton SO30 2DF. Terms and conditions apply.
The GDHV guarantee does not in any way diminish or affect your statutory consumer rights in connection with your product.
If you experience a problem with your product during or after the guarantee period, visit our online help centre:
https://www.dimplex.co.uk/gdhv-help-centre
If you cannot solve your issue online, contact the customer care team on 0344 879 3588
Please note that when you contact us you will need to provide the model and serial number of your product and a description of the fault which
has occurred.
© Glen Dimplex UK Limited. All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Glen Dimplex
Customer Helpline: 0344 879 3588
www. dimplex.co.uk
Glen Dimplex Heating & Ventilation
Millbrook House, Grange Drive, Hedge End, Southampton, SO30 2DF
This product complies with the European Safety Standards EN60335:2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014:1, EN55014:2, EN61000:3-2
and EN61000:3-3 which cover the essential requirements of EMC Directive 2014/30/EU and the LVD Directive 2014/35/EU.
To view the full guarantee terms and conditions scan this QR code using your smartphone or go to
https://www.gdhv.co.uk/guarantee-terms-and-conditions.
Why Register Your Products With Us?
Faster Customer Service
Once you have registered your product,
our customer service team wil be able
to quickly access your details when you
contact us, allowing them to help you
sooner.
Guarantee Management
Upon registration, you will receive a
conrmation email including a summary
of your product guarantee, a copy of our
terms and conditions and a copy of your
proof of purchase (optional).
Product Recall Notication
If your product is registered you will
automatically be contacted with applicable
safety notications, or in the unlikely event
of a product recall.
Please register your product with us within 28 days of date of purchase to enable us to provide efcient customer service if you need to contact
us, to contact you in the event of a product or safety update, to extend your guarantee where applicable, and, if you choose, to send you additional
information about our products and services.
Register your product at https://www.gdhv.co.uk/register, or if you do not have access to the internet, call us on 0344 879 3588.
On registering you will automatically receive a copy of the terms and conditions of your guarantee, which can also be downloaded at any time
from https://www.gdhv.co.uk/guarantee-terms-and-conditions. If you do not have access to the internet, call us on 0344 879 3588 and we will
send them to you by post.