Dimplex OFRC10BLK User manual

INSTRUCTION MANUAL
For domestic household use only.
Oil Free Column Heaters
Model: OFRC10BLK, OFRC15BLK & OFRC24BLK
08/54739/0 Issue 3

CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE
INJURY AND/OR DAMAGE AND MAY INVALIDATE YOUR WARRANTY
Please read the operating instructions carefully before using your product
for the first time and keep them in a safe place.
• When using electrical appliances, basic precautions should always be
followed to reduce the risk of fire, electrical shock and injury to persons,
including the following:
• If the appliance is damaged, check with the supplier before installation
and operation.
- Do not use outdoors.
- Do not use in the immediate surroundings of a bath, shower or
a swimming pool.
- Do not use this heater if it has been dropped.
- Do not use if there are visible signs of damage to the heater.
- Use this heater on a horizontal and stable surface, or fix it to
the wall, as applicable.
• Do not locate the appliance immediately below a fixed socket outlet or
connection box.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the
appliance.
• CAUTION: Some parts of this product can become very hot and cause
burns. Particular attention must be given where children and vulnerable
people are present.
• IMPORTANT: Only use this heater on a horizontal and stable surface
with the castors attached.
• WARNING: In order to avoid overheating, do not cover the heater.
• The Heater carries this warning symbol indicating that it must
not be covered.
• Do not use this appliance in series with a thermal control, a program
controller, a timer or any other device that switches on the heat
automatically, since a fire risk exists when the appliance is accidentally
covered or displaced.
IMPORTANT
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED
FOR FUTURE REFERENCE. Note also the information presented on the
appliance
2

• In the event of a fault, unplug the appliance.
• Unplug the appliance when not required for long periods.
• This product is intended for INDOOR RESIDENTIAL applications only.
• DO NOT cover cord with carpeting, throw rugs, runners, or similar
coverings.
• DO NOT route cord under furniture or appliances. Take care to position
the cord away from traffic areas and where it will not be a tripping
hazard.
• This appliance must not be used in a bathroom.
• Although this appliance complies with safety standards, we do not
recommend its use on deep pile carpets or on long hair type of rugs
• The appliance must be positioned so that the plug is accessible.
• If the supply cord is damaged it must be replaced by the manufacturer
or service agent or a similarly qualified person in order to avoid a hazard.
• Keep the supply cord away from the front of the appliance.
• Do not use this heater in small rooms when they are occupied by
persons not capable of leaving the room on their own, unless constant
supervision is provided.
• To reduce the risk of fire, keep textiles, curtains and or flammable material
a minimum distance of 1m from the air outlet.
• DO NOT place material or garments on the appliance, or obstruct the
air circulation around the appliance, for instance by curtains or furniture,
as this could cause overheating and a fire risk.
• In order to avoid a hazard due to inadvertent resetting of the thermal cut-
out, this appliance must not be supplied through an external switching
device, such as a timer, or connected to a circuit that is regularly switched
on and off by the utility.
IMPORTANT
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED
FOR FUTURE REFERENCE. Note also the information presented on the
appliance
3

Exposed to the
weather outdoors
Near water If the power cable
wires are frayed or cut
Where small children
may be left unattended
No extension leads or
power boards
Where there is risk
of fire or close to
a naked flame
Where the power
cable may be
damaged
On a slope or
uneven surface
Where it may be
damaged by
chemicals
If there is a risk
of water falling on
the unit
Where there is a risk
of interference by
foreign objects
This product is not
made for DIY repair
4

Model no. OFRC10BLK OFRC15BLK OFRC24BLK
Power supply 230-240V~50Hz
Rated power 1000W 1500W 2400W
Heat settings
2
Thermostat Y
Timer N
Turbo Fan N
Weight (net) 6.4kg 8.3kg 10.7kg
Dimensions (w x d x h) 280 x 280 x 622mm 280 x 370 x 622mm 280 x 550 x 622mm
Specifications
For greater precision, please always refer to the rating label placed on the product.
WARNING THIS APPLIANCE MUST BE EARTHED
5

Fitting The Castors
WARNING The column heater must only be operated with the wheels and castors
fitted and in an upright position. The castors must be fitted to the control panel and
on the bracket between the last and second last fin on the opposite end, as shown
in Fig.1.
Fitting the castors
1. Remove the box containing the castor assemblies from the packaging.
2. Fit the castors to the stub axles by applying hand pressure until each castor
clicks into position - see below Fig. 2. Note that the castors are designed to be a
tight fit on the axles but will rotate in use.
3. The castors can only be fitted between the outer fins (as shown in Fig. 1).
4. Turn the heater upside down on a carpet or other soft surface to avoid damage.
Ask a second person to help with this if necessary.
WARNING: THE HEATER IS HEAVY – ENSURE THAT IT IS SUPPORTED TO
PREVENT IT FROM TOPPLING.
5. Position the castor bracket (see Fig. 2) onto the threaded pins on the control
panel. Place the winged nut ‘C’ on the thread and tighten it securely.
6. Repeat the process for castor bracket ‘B’ onto the last fin.
7. Lift the heater clear off the floor, then turn it back upright and stand it on its
castors. It is now ready for use.
Fig 1. Fig 2.
OFRC15/OFRC15TI
OFRC25/OFRC25TI
B
A
B
A
4
5
On/O see
Table 1
A
B
C
3
A
B
C
3
5 Fin
7/9/11 FinOFRC10/OFRC10TI
OFRC15/OFRC15TI
OFRC20/OFRC20TI
OFRC25/OFRC25TI
B
A
B
A
B
A
B
A
OFRC10BLK
OFRC15BLK
OFRC24BLK
6

Positioning
Select the position for the heater ensuring there is clearance from any furniture
and fittings of at least 300mm above the heater and 150mm each side. The heater
should only be operated on a flat stable surface.
NOTE: The column heater is designed for operation on an AC electricity supply, and
is only suitable for domestic use and similar indoor locations.
Tips
• The column heater is fitted with castors and a handle for ease of movement.
• A rocker switch provides the ability to choose an available heat output and
an adjustable thermostat enables the room temperature to be controlled
accordingly.
• Once the castors have been correctly fitted, no other assembly is required, just
plug in and play!
Safety Features
This appliance incorporates a number of safety devices. In addition to the ‘Important
Safety Advice’ section your attention is drawn to the following;
Tilt Switch
The tilt switch will prevent the heater from working if it is accidentally tipped over on
its side.
If the radiator is tipped over while it is hot, disconnect the power and allow it to cool,
then stand the radiator back upright. Reconnect the power - normal operation should
be resumed.
Overheat Protection
The heater is fitted with a temperature limiter which will reduce the output of the heater
should it overheat for any reason. The product will return to normal operation after the
cause of the over heating has been rectified.
7

Operation
IMPORTANT - OBJECTS OR CLOTHING MUST NOT BE PLACED ON THIS HEATER.
Before using the column heater ensure that all warnings and instructions have been
read carefully. To turn ON the heater simply plug it in. Neon indicator lights located
near the control area will illuminate when the appliance is plugged into a power
outlet. This indicates the appliance is in standby mode and ready to use.
Please note – The element has been coated with a protective film which will burn off
during the first few minutes of use, this may cause a small amount of fuming. This is
quite normal – the fumes are non-toxic and will disappear quickly.
We recommend that you open a window to ventilate the room when using the
heater for the first time.
Handle
Thermostat dial
Indicator light
On/Off & Heat switches
Cable wrap
Thermostat Dial
On/Off & Heat Switches
Description of Parts
8

Operation
Thermostat
The Thermostat Dial (see previous page) controls the heat output according to
the room temperature. This ensures that the column heater will not produce heat
unnecessarily when the room is already warm.
1. To set the temperature, turn the thermostat dial clockwise until the required
setting is reached. Alternatively to heat a cold room quickly, turn the thermostat
dial up fully.
2. When the room has reached the desired temperature, turn the thermostat
dial anti-clockwise until the thermostat just clicks off. The heater will now
automatically operate at this temperature.
3. The thermostat also has a frost protection setting marked '*' This setting is useful
in areas such as garages, or other cold indoor rooms, to prevent frost damage. If
the thermostat is set to its minimum setting '*' the heater will cycle on and off to
maintain a temperature of approximately 5°C to help protect against frost.
Note – If the heater fails to turn ON when the thermostat is at a low setting, this may
be due to the room temperature being higher than the thermostat setting.
On/Off & Heat Switches (see previous page)
Selector switches located on the control panel provide a choice of heat output to
suit varying conditions and for economy of operation.
Available output options are as follows:
On/Off Switches (Left) Heat Switches (right)
Model O I I II
OCR10BLK
Off On (700W) 700W 1000W
OCR15BLK Off On (1000W) 1000W 1500W
OCR24BLK Off On (1700W) 1700W 2400W
9

WARNING - ALWAYS DISCONNECT THE POWER SUPPLY BEFORE CLEANING THE
HEATER.
• Do not use detergents, abrasive cleaning powder or polish of any kind on the
body of the column heater.
• Allow the column heater to cool, then wipe with a dry cloth to remove dust and
a damp cloth (not wet) to clean off any marks. Be careful not to allow moisture
into to the heater.
Storage
If the heater is not required for long periods, for example during the summer, it should
be stored in a dry place and preferably covered to prevent the accumulation of dirt
and dust. The supply cord should be neatly coiled around the cable wrap ensuring that
the plug does not trail on the floor.
Cleaning
10