Dimplex Saletto LPP050E User manual

08/80070/0 ISSUE: 2 Series: A
These instructions should be read carefully
and retained for future use. Note also the
information presented on the appliance.
INSTRUCTION MANUAL
Installation and Operating
Dimplex Saletto (LPPE)
Models: LPP050E / LPP075E / LPP100E / LPP150E

IMPORTANT
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR
FUTURE REFERENCE. Note also the information presented on the appliance
CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY AND/
OR DAMAGE AND MAY INVALIDATE YOUR GUARANTEE
IMPORTANT SAFETY ADVICE
When using electrical heaters, basic precautions should always be followed to reduce
the risk of fire, electrical shock, and injury to persons, including the following:
IMPORTANT: The wall bracket supplied with the heater must be used.
IMPORTANT: All packaging should be disposed of in an appropriate manner.
OVERHEATING WARNING
WARNING:In order to avoid overheating, do not cover or obstruct the heater. Do not
place material or garments on the heater, or obstruct the air circulation around the heater,
for instance by curtains or furniture, as this could cause overheating and a fire risk. NEVER
cover or obstruct in any way the heat outlet slots at the top of the heater or the air inlet
slots in the base of the heater.
WARNING:
THE SURFACES ON THIS HEATER CAN BE HOT. The heater carries a
warning ‘DO NOT COVER’ to alert the user to the risk of fire that exists if the heater is
accidentally covered. DO NOT place combustible items through the heater grille.
CAUTION:Some parts of this product can become very hot and cause burns. Particular
attention has to be given where children and vulnerable people are present.
For your safety this heater is fitted with a thermal cut-out. In the event that the
product overheats for some reason, the cut-out prevents excessive temperatures on
the product by cutting the power to the heater. Once the heater has cooled down,
it will reset automatically, it will continue to cycle on and o automatically until the
reason for overheating is removed. The display screen may flash red to indicate the
product has overheated. To reset the display, remove the obstruction and hold Enter
for 10 seconds.
2

SUITABLE APPLICATIONS
WARNING: This heater is suitable for normal domestic household purposes and
should not be used in any other type of environment. This product should only be
used in the country where it was purchased from by a recognised commercial retailer.
Do not use outdoors.
SERVICING AND REPAIRS
WARNING
: Servicing and product repairs should only be undertaken by the
manufacturers approved service agent or a similarly trained or qualified person, using
only exact manufacturer approved spare parts.
PLEASE NOTE: Household dust, lit cigarettes, candles and oil burners, combined with
the convection eect of electric heaters can cause significant soot deposits to build
up on the surface directly above and to the sides of the heater. This is not a fault of the
heater. Extensive burning of candles or smoking in the operating environment of this
product can produce heavy discolouration within a few months of use.
OPERATING WARNINGS
IMPORTANT: Remember to observe all safety warnings and precautions when
operating the heater on the automatic or timer modes, either attended or unattended
since a fire risk exists when the heater is accidentally covered or displaced.
CAUTION: Do not use if the heater’s mains power lead is damaged. If the supply cord
is damaged it must be replaced by the installer or an approved Dimplex service partner.
3

ELECTRICAL INSTALLATION
WARNING: The electrical installation of this heater must be carried out by a
suitably qualified or trained electrician, and be in strict accordance with the
current wiring Regulations BS 7671. The supply must be connected via a switched
fused spur with a fuse rated suitably for the appliances flex. Failure to follow these
instructions will mean that the manufacturer’s instructions have not been adhered to.
THERE ARE NO EXCEPTIONS.
WARNING: Minimum clearances and IP zone requirements must be adhered to in
accordance with the current wiring regulations.
The wires in this mains lead are coloured in accordance with the following code:
GREEN AND YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
• This heater must be earthed
• Not suitable for connection via a plug top
• Do not locate the heater immediately below a fixed electrical point i.e. socket outlet.
The heater is fitted with a length of flexible cable type H05VV-F size 3 x 1.0mm² for 500W
to 2kW models for connection to the fixed wiring of the premises through a suitable
connection box positioned adjacent to the heater. A means for disconnection must be
incorporated in the fixed wiring of the premises in accordance with the current wiring
regulations. The supply circuit to the heater must incorporate a double pole isolating
switch having a contact separation of at least 3mm. Products that are supplied without
a plug are for installation into the fixed wiring of the property, via a suitable double pole
switched fused spur with a fuse rated suitably for the appliances flex. Typical fuse ratings
for 230V equipment - Up to 700W = 3A, over 700W = 13A.
In installation the supply cord must be cut to the appropriate length for the electrical
connection point. Excess cable should not be inserted and stored behind the heater.
WARNING: This heater must not be connected to the electricity supply via an external
switching device (such as a timer) or a circuit that is regularly switched on and o by
the utility supplier. Failure to follow this warning could result in the heater’s thermal
cut-o being inadvertently reset and could create a fire hazard. Cables/flexes that are
supplied pre-fitted to the product must NOT be extended.
4

CHILD SAFETY
WARNING : This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of appliance by a
person responsible for their safety.
This appliance can be used by children from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance. Children
shall not play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision. Children of less than 3 years should be kept away unless
continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/o the appliance
provided that it has been placed or installed in its intended normal operating position
and they have been given supervision or instruction concerning use of the appliance in
a safe way and understand the hazards involved. Children aged from 3 years and less
than 8 years shall not regulate and clean the appliance or perform user maintenance.
This product contains a replaceable battery.
WARNING: KEEP BATTERIES OUT OF REACH OF CHILDREN.
WARNING: Packaging should be disposed o responsibly as the EPS could be a
potential choking hazard for children
5

Model Identifier(s): LPP
050E
LPP
075E
LPP
100E
LPP
150E
Nominal heat output Pnom 0.5 kW 0.75 kW 1 kW 1.5 kW
Height (mm) 235 235 235 235
Width (mm) 746 746 877 1142
Depth (mm) 100 100 100 100
Minimum heat
output (indicative) Pmin N.A. N.A. N.A. N.A.
Maximum continuous
heat output Pmax,c 0.5 0.75 1 1.5
Auxiliary electricity Consumption
At nominal heat output elmax 0.00 0.00 0.00 0.00
At minimum heat output elmin 0.00 0.00 0.00 0.00
In standby mode elSB <0.0005 <0.0005 <0.0005 <0.0005
With open window detection Yes
With adaptive start control Yes
Type of heat output/ room temperature control
With electronic room temperature control Yes
Electronic room temperature control plus week timer Yes
With open window detection Yes
With adaptive start control Yes
This product complies with Lot20 of the Energy Eciency Directive (2015/1188).
Energy Related Product Directive
Technical Details
6

All Models
Controls
Digitally controlled, Electronic Thermostat accurate to (±0.2oC)
Timer modes:
7 Day Programmable User Timer, Out All Day, Home All Day, Holiday
Continuous heat modes:
Eco, Manual, Frost Protect, Setback, Runback, O
Controller UI
• Graphical display with RGB backlight
• Capacitive buttons with audio feedback
• User replaceable battery (Coin-Type)
Controller Functions
• Open window detection, Adaptive-start
• Advance time period
• Adjustable max setpoint range (7-32°C)
• Bluetooth for software updates
• Child Lock & Landlord Lock (PIN-based)
Construction
• Durable epoxy-polyester powder coated steel casing with louvered
upward facing grille
• Advanced controls with capacitive sense technology for total
flexibility of heating
Finish / Colour
Metal Chassis, Air Outlet Grille & Control Moulding
Trac White (RAL 9016)
Element Compact, finned, mineral filled sheathed element
Installation • Wall bracket
Safety
• Thermal cut-out. Auto reset type
• Overheat detection
• Advance time period
IP Rating IP24
Battery
3.3V coin cell battery to backup real time clock. Battery life >5 years.
Supply
1.3 metres fitted, 3 core for fused spur installation, 1/N/PE ~230-240 V,
50Hz Class I, with earth wire
Approvals CE, BEAB
Warranty 2 years
Country of Origin United Kingdom
Manufacturer Glen Dimplex Heating & Ventilation (GDC Group Ltd.)
7

WARNING:
This product is heavy and care
should be taken in installation
Please read the instructions closely before first using the product, there is also a
quick-start guide on page 8 if you need a reminder of how to use the basic functions
in the future. The heater is designed for wall mounting using the wall bracket supplied.
It should only be operated when in the upright position as shown - see Fig.3 and Fig.4.
All models are splash proof to IP24. Before connecting the heater check that the supply
voltage is the same as that stated on the heater.
MODEL A B C D E
LPP050E 672mm 150mm 746mm 235mm 100mm
LPP075E 672mm 150mm 746mm 235mm 100mm
LPP100E 803mm 150mm 877mm 235mm 100mm
LPP150E 1068mm 150mm 1142mm 235mm 100mm
General Information
Wall Mounting Instructions
IMPORTANT - The wall bracket
supplied with the heater must
be used and the heater must
be installed in the correct
orientation. The fixings should
be used to secure the bracket to
the particular wall on which the
heater will be installed. The heater
should be positioned observing
the minimum clearances stated
around the heater - see Fig. 2,
Fig. 3 and Fig. 4.
‘A’
250mm
‘B’
Minimum
mounting
clearance
Minimum mounting clearance
Fig. 2
8

To mount the heater to the wall:
1. Remove wall mounting bracket from the back of the heater by depressing the spring
latch at the side of each bracket - see Fig.2.
2. Fix the wall bracket securely to the wall through the four screw holes. Ensure only
screw fittings suitable for the particular wall type are used.
3. Present the heater to the wall bracket and engage bottom slots in the back with
bracket hooks.
4. Press the top of the heater into locked position and ensure the clips on the top are
engaged.
WARNING:
This product is heavy and care
should be taken in installation
‘C’ 150mm
(min)
150mm
(min)
150mm
(min)
‘D’
Minimum mounting clearance
300mm
170mm*
(min) ‘E’
Shelf / Obstruction
*The minimum distance
from the shelf should be
170 minimum if the shelf
is wider than 50mm, or
50 minimum if the shelf
is 50mm or less.
Minimum front
clearance
Please note correct product
orientation is with controller
facing top right side only
150mm
(min)
Fig. 3
Fig. 4
9

How Does the Heater Control Work?
The controller allows you to choose when you want heat and at what temperature.
When using a timer mode (see below), Comfort On will display on the home screen to
tell you when the heater is maintaining the temperature displayed. Comfort O will
display when the heater is outside of a timed heating period. When Manual, Eco or
Frost modes are being used the heater will always maintain the temperature shown
on the home screen.
Set the Time
To set the date and time on the heater, press Menu, then press Enter with Time / Date
highlighted. Press or until the correct value is shown, then press Enter to confirm
and move onto the next value. Repeat until all details are correct, and Set displays,
then press Back. The time is automatically adjusted in spring and autumn between
Greenwich Mean Time (GMT) and British Summer Time (BST).
Set the Temperature
The temperature shown on the display is the room temperature set point (target
room temperature). This is the temperature that the heater will maintain during the
heating periods. If the room temperature is above this temperature then the heater
will not operate. The heater leaves the factory with this temperature set at 21°C which
represents a typical, comfortable room temperature. If you require a dierent room
temperature, use either or until the display shows the temperature you require.
Timer Modes
Your Dimplex LPPE Panel
comes pre-programmed
with four timer modes. These
modes define the periods
when the heater will operate
in Comfort On mode. The four
modes are shown in Fig.5
This guide is for quick reference only.
Please refer to the operating section on Page 12 for further information.
Timer Mode Description
User timer Customise times in four periods
Out All Day 6 hours heating per day in two
periods
Home All Day 13 hours heating per day in one
period
Holiday
Set the temperature and number
of days for which you are on
holiday
Quick Start Guide
Which Timer Mode is Best for Me?
The heater leaves the factory set in Out All Day mode. If you are out during the day
and only require heat in the mornings and evenings then this mode will likely suit your
lifestyle.
If you are in during the day then you should select the Home All Day mode which is
a single heating period.
Fig. 5
10

The User Timer mode will give you four periods of heating split throughout the day.
If you are away for an extended period of time then you can use the Holiday mode.
This allows you to reduce the heating during the period that you are away, reverting
to the previously selected mode on the day you return.
Advance
Sometimes you may be at home when you had not planned to be, or need to leave
when you had planned to have the heating on. You can change the way you use your
heating temporarily, this temporary change is achieved by using the Advance function.
When a timer has been selected, the Advance function allows you to begin the next
period early. If the heater is in a Comfort O period and you want heat - press the
Advance button. If the heater is in Comfort On and you don’t want heat, press the
Advance button and it will go o until the beginning of the next Comfort On period.
Advance Boost
The Advance button is also used to enter the boost mode which provides temporary
heating for one, two, three or four hours. Press the Advance button twice to begin a one
hour boost. Continue pressing the Advance button to enter the longer boost periods.
NOTE:
Advance Boost only works when not in timer mode
Out All Day
Comfort On
Out All Day
Selected
Out All Day
Select
Preview
Modify
Mode
Timer Mode
Boost
Setback
Timer Mode
Out All Day
Home All Day
Holiday
User Timer
Main Menu
Date/Time
Mode
Options
To choose a timer mode press Menu
followed by Enter to select Timer Mode.
Select the mode required by pressing
or and then Enter. For options Out All
Day, Home All Day and User Timer, three
choices are available
Select, Preview and Modify.
Select - Choose this timer option
Preview - View the times currently set
Modify - Change the times currently set
Please refer to the operating section of this
manual for information on how to modify the
programmed times
11

The controls are located on top of the heater. The heater is fitted with an adjustable
electronic controller consisting of a display screen and six touch sensitive buttons.
The heater is fitted with an adjustable thermostat enabling the room temperature to
be controlled. The minimum room temperature is 7°C. The maximum temperature
is set to 26°C by default however this can be increased to 32°C if required. A
temperature of 21°C represents a normal room temperature.
1Display Screen
2‘Menu’ Button
3‘Back’ Button
4‘Up and Down’ Arrows
5‘Enter’ Button
6‘Advance’ Button
7Heating Status
NOTE:
Should the heater fail to operate, this
may be due to the room temperature
being higher than the thermostat setting.
NOTE:
Your heater may produce some noise
during operation. This noise is caused
by the expansion and contraction of the
element as it changes temperature, and
is normal for this type of product. Whilst
the noise produced is usually very quiet,
certain environmental factors can make
it more noticeable, such as hard flooring
or minimal furnishings If you believe that
the expansion noise is excessive, please
contact us.
Out All Day
Comfort On
1
57 3
2 46
Operation Manual
WARNING: FAILURE TO FOLLOW THESE OPERATING INSTRUCTIONS MAY RESULT
IN INJURY AND/OR DAMAGE.
12

The heater controls can be easily adjusted by using the six buttons on the User
Interface.
1The Display Screen shows the options available at each stage of adjustment.
2Menu - displays the main options list;
- Date/Time - Set the date and time.
- Mode - Set the mode of operation.
- Options - Temperature units, daylight savings time, lock settings and
service information.
3Back returns to the previous programming stage.
4The and buttons are used to navigate through the menus and alter setting
values. The and buttons are also used to adjust the required room temperature
on the main screen. The screen colour changes based on the temperature selected,
showing deep blue through to bright red.
5
Enter is used within the menu options to confirm settings. On the main screen
pressing Enter will display the enabled features.
The timed periods during which the heater is providing heat are defined as
‘Comfort On’ (this is displayed at the bottom of the screen).
Outside of heating periods the heater will not deliver heat and these periods are
called ‘Comfort O‘.
While constant heat modes are active, the mode of operation is displayed at the
bottom of the screen e.g. ‘Manual’.
6The Advance button overrides the heating settings and changes the operational
state of the heater. If a timer mode is selected, pressing Advance will cause the
heater to remain on until the next Comfort O period is due, or o until the next
Comfort On period is due.
If the heater is in a continuous heat mode of operation, Advance can be used to
switch the appliance on and o.
Advance is also used to enter Boost mode. Boost mode delivers heat for between
one and four hours if the appliance is in a Timer Mode.
If Runback is enabled and the appliance is in Standby mode, the Advance button
is used to enter a timed Runback heating period.
Control Functions
13

After 30 seconds the heater will default back to the Main Screen. Here the current
target temperature (setpoint) is displayed along with the mode of operation. Any
use of the Advance function will be displayed here, and pressing Enter will show the
functions which are enabled.
When left inactive for a long period of time this display will ‘sleep’ and the text will
disappear. Press any button for its return.
ESOW
UI Rev 70
Date/Time
THU
27/07/2017
07:12
Date/Time
Set
Out All Day
Comfort On
Main Menu
Date/Time
Mode
Options
Out All Day
Comfort On
Main Screen
The heater incorporates a real time clock with calendar
function. The time clock has a battery backup that
will keep the clock running in the event of a mains
power outage.
To adjust the time or date follow the steps below.
Press the Menu button. Select Date/Time by pressing
the Enter button. Press and to select the correct
day of the month and press Enter to select.
Repeat this operation, until the date and time has
been set, ensuring to press Enter to select. Press
Back button to return to the Main Screen once Set
has been displayed.
Setting the Date and Time
NOTE:
The display screen
will return to the main
screen after a period
of 30 seconds of
inactivity.
NOTE:
Pressing enter will
show the functions
which are enabled,
e.g. ES and OW above.
Ref: page 19.
14

NOTE:
In all modes, and can be used to adjust the required room
temperature. In timer modes, this change is temporary and the heater
will set the room temperature based on the saved heating profiles.
NOTE:
It is recommended that the timer is used as doing so can reduce
the running cost. Operating the appliance in the permanent
heating modes may result in increased running costs.
The heater comes pre-programmed with a set of heating profiles. The user can change
if he / she want to. There are four options available - three pre-programmed and one
user adjustable timer;
1. User Timer - provides greatest flexibility to the user. Four time slots are available
throughout the day and these can be customised for each day of the week.
2. Out All Day (pre-programmed) - has the following preset times Monday to Sunday,
which can be altered if desired 07.00 until 08.30 17.30 until 22.00
3. HomeAllDay(pre-programmed)-hasthefollowingpresettimesMondaytoSunday,
which can be altered if desired; 08.00 until 21.00
4. Holiday (pre-programmed for 7 days at 10°C) - set the number of days required
(from 1 to 255) and the temperature required. 7°C is advised if you just want to
protect the property from frost while you are away.
The heater can also maintain a constant room temperature using the following modes;
1. Manual Mode maintains a comfortable room temperature.
2. Eco Mode maintains a room temperature of 18°C. By reducing the room
temperature slightly, significant energy savings can be achieved. The green
display colour indicates that the selected temperature provides a comfortable
room temperature while reducing energy consumption.
3. Frost Protect Mode maintains a room temperature of 7°C. This mode should be
used to provide protection against frost as indicated by the blue display.
Select Standby to switch o the heating element. Heating will not be provided.
Modes of Operation
15

Timer Modes
To choose a timer mode press Menu from the home screen, then navigate to
‘Timer Mode’ using the button. Press Enter to select.
Select a timer by pressing or followed by Enter.
For Out All Day, Home All Day and User Timer, will show three choices available
- Select, Preview and Modify.
• Select - This option will activate the timer.
• Preview - This option allows you to quickly view the times and temperatures
currently set
• Modify - This option allows you to modify the times and temperatures.
When Modify is chosen, select and change each option using the , and Enter
buttons. At the end of each heating period, select Next to move to the following
heating period. When a day is complete, the following options are available:
• Save - Saves times for one day.
• Copy Next - Copy times from the day shown to the following day.
• Copy All - Copy times from the day shown to all seven days.
• Clear - Remove all times from the day shown.
• Clear All - Remove all times for all seven days. NOTE:
Once modified a programme
must be selected if you want
to begin using it.
07:30
Comfort O
Next on at
08:00
Main Menu
Date/Time
Mode
Options
Mode
Timer Mode
Manual
Eco Mode
Frost Protect
Standby
Timer Mode
Out All Day
Home All Day
Holiday
User Timer
Out All Day
Select
Preview
Modify
Morning
On 07:00
O 08:30
21 °C
Next
< TUE >
Evening
On 19:00
O 20:30
21 °C
Save
< TUE >
Saved
Out All Day
Choosing and Setting a Mode
Example of Modifying the Out All Days timer is shown
16

In Holiday mode the number of days that the room will remain unoccupied for can
be adjusted together with the required room temperature.
Press and to choose a holiday period between 1 and 255 days, then press the
Enter button.
Press and to choose a temperature to be maintained during this period and press
the Enter button. At the end of the Holiday mode the heater will automatically revert
back to the previously selected programme.
NOTE:
If the EcoStart is enabled the heater will maintain the room
at the required temperature for the duration of the heating
period. To achieve this, the heater will begin heating the
room before the start of the heating period to ensure the
room is at the required temperature when the period starts.
If EcoStart (ES) is disabled, the heater will not operate until
the beginning of the heating period. This should be taken
into consideration when setting the heating periods.
See page 19 for instruction on enabling/disabling EcoStart.
The Advance function allows the active timer schedule to be changed temporarily. When
a timer has been selected, the Advance function is used to begin the next Comfort
On mode early. If the heater is in Comfort O mode and heat is required, press the
Advance button.
If the heater is in Comfort On and heat is not required, press the Advance button and
the heater and the heater will stop heating until the beginning of the next Comfort
On period.
If the heater is in Manual, Eco Mode or Frost Protect, pressing the Advance button
will pause that operation. The heater will remain paused until the Advance button is
pressed again.
Home All Day
Comfort On
Advance
Advance
17

The Advance button is also used to enter the Boost mode which provides temporary
heating for one, two, three or four hours.
Press the Advance button twice to begin a one hour boost. Continue pressing the
Advance button to set longer boost period.
Comfort On
Boost 1hr
Boost
The Options menu allows the settings to be modified to suit the user’s preferences.
These are:
DST Rule - Select your daylight saving setting. The heater clock will automatically
adjust for daylight saving time. If no adjustment is required then select none.
Auto Lock - Enable or disable the auto lock feature. This feature locks the interface if
left inactive for longer than one minute. To unlock the appliance, press and hold Back
and Enter for two seconds.
Sound - Audio feedback can be enabled or disabled.
Service Info - Service information is displayed.
Temp Units - Choose whether your unit displays degrees Centigrade or Fahrenheit.
Comms - Choose to enable or disable Wireless Connectivity.
If additional RF Module is connected, user will have option to enable or disable RF
communications.
DST Rule
Auto Lock
Sound
Service Info
Temp Units
Comms
Options
Options
18

If you need to lock the controls so that the settings cannot be changed then activate
the Child Lock.
To lock the controls press Back and Enter for three seconds.Child Lock will appear
at the bottom of the screen. To unlock the control repeat the action of pressing Back
and Enter for three seconds.
NOTE:
The controls cannot
be adjusted when
child lock is active. Child Lock
User Information
Press and hold Enter for five seconds to display the User Information menu;
Runback,when enabled, allows the user to activate a timed heating period by pressing
the Advance button when the appliance is in Standby mode. The settings of the timed
heating period, duration and temperature can be configured in Runback Settings.
Runback is enabled by default.
Temp Settings allows the user to select the Max Temp to adjust the maximum temperature
range of the appliance. Setback allows the user to select a background temperature
setting when the product is not in a Timer Mode Comfort On period.
Open Window detection (OW), when enabled, allows the heater to reduce the target
room temperature, limiting energy waste. Enabled as default when an open window
is detected.
EcoStart (ES) - to achieve the desired temperature at the onset of the timed Comfort
On period, the appliance anticipates when it needs to start heating prior to the onset
of the timed on period. E.g. room is 16°C, with 21°C at 7am set on the timer. With ES
On the control will start to heat the room before 7am, reaching 21°C at this time. With
ES o the heater will start to heat the room at 7am and will reach 21°C after this time.
Factory Reset returns all settings to the factory presets.
User Info
Runback
Temp Settings
Open Window
Eco Start
Factory Reset
User Information
Child Lock
19

Introduction
This appliance has a built in runback lock mode, when this
mode is activated the user will have limited functionality
with no access to the settings of the runback timer. It is
possible to limit the maximum operating temperature and
runback duration in the runback lock mode. This mode
also features a setback function where a non-adjustable
setback temperature can be set.
Operation in Runback mode
When runback mode is active the appliance settings
are locked, it is only possible for the user to activate
predetermined runback periods. During these periods the
appliance will energise to control the room to a desired
temperature. During a runback period the set-point can
be adjusted by the user however, it is possible to assign a
maximum set-point limit during the runback mode setup.
Once the runback period has elapsed the appliance will
switch into Comfort o mode or into setback mode if
enabled.
To activate a runback period the user must press the
Advance button. There will be four runback periods
available to chose from which are accessible through
sequential presses of the Advance button. A subsequent
press of the Advance button will return the appliance to
Comfort o mode or Setback mode.
12:00
Comfort
O
Runback
60 Minutes
Comfort
On
Runback
90 Minutes
Comfort
On
12:00
Comfort
O
Comfort
On
Runback
30 Minutes
Runback Lock Mode
Comfort On
Runback
120 Minutes
20