Diode Dynamics STAGE Series User manual

PP0081
PP0132C
Type MS Foglight Kit
SS33” LED Pod
PAGE 4
WARRANTY
3 YEAR
This installation guide is for the following SKUs:
DD6576 Worklight SS3 Sport Type MS Kit White SAE Driving
DD6577 Worklight SS3 Sport Type MS Kit White SAE Fog
DD6578 Worklight SS3 Sport Type MS Kit Yellow SAE Fog
DD6579 Worklight SS3 Pro Type MS Kit White SAE Driving
DD6580 Worklight SS3 Pro Type MS Kit White SAE Fog
DD6581 Worklight SS3 Pro Type MS Kit Yellow SAE Fog
DD6706 Worklight SS3 Max Type MS Kit White SAE Fog
DD6707 Worklight SS3 Max Type MS Kit Yellow SAE Fog
Please contact Diode Dynamics should you have any questions about the installation
or wiring process, at 314-205-3033 (10a-5p CST) or [email protected].
GUARANTEE
100% SATISFACTION 8
year
warranty
PP0170
Scan the QR code to link to our YouTube Channel!
NEED MORE HELP?
We continuously bring in vehicles to our testing garage in order to
create step-by-step videos to walk you through the installation process
on your specic vehicle. Scan the QR code to see all our installation
videos. Be sure to subscribe to our channel to stay up-to-date on the
newest products and videos from Diode Dynamics!
25 feet
Top of
Beam
Level
Measure lamp height to center
Four (4)inches
13. Aim your SS3 pods on each side, so that
the top of the beam pattern is on the
cuto line mark.
14. Tighten the 5/32” allen bolts back down.
PAGE 1
[phone] WWW.DIODEDYNAMICS.COM
See inside for further instructions.
15. R einstall the fog light covers and splash
guard to complete the installation.
Thank you for your purchase of our new SS3 Type MS Foglight Kit. CAD-designed to use existing
mounting points, this kit is compatible with the Jeep JL Wrangler and JT Gladiator Sport. Basic
installation instructions are included below. Please contact us if you have any questions.
TOP
BOTTOM
1. Attach the bracket to the pod loosely, using one screw
on each side. These screws will also determine the aim of
your SS3 pods. See the diagrams above and to the right.
Make sure the bracket is in the correct orientation.
Left and Right Sides
Factory
Hardware

PAGE 2 PAGE 3
[phone] WWW.DIODEDYNAMICS.COM
Aiming Instructions
8. Park your vehicle 25 feet away from a wall
or garage door on a level surface.
9. Loosen the 5/32” allen bolts on each side
of your SS3 pod, just enough to allow you to
adjust the pod.
10. On your vehicle, measure the distance
between the ground and the center of your
SS3 pod. This is your mounting height.
11. Mark the mounting height on the wall
or garage door using tape.
12. Add another piece of tape four inches
below the mounting height. This is your fog
light cuto line.
See back for further instructions.
7. Repeat the steps on the other side of the vehicle.
MOUNTING HEIGHT
CUTOFF LINE
2. Using a trim removal tool, remove the eight
push rivets along the front of the splash guard.
We recommend prying on both accessible sides
of the push rivets at the same time due to their
large size.
Remove the splash guard. To do so, use an 8mm
socket and ratchet to remove the two bolts on
the bottom of the splash guard.
3. Remove the plastic fog light covers. To do so,
use a 7mm socket and ratchet to remove the
seven screws shown in the picture to the left.
4. Remove the factory fog light assembly. Use
a T20 Torx driver to remove the three screws.
We recommend using hand tools to reduce the
chance of thread stripping or heating of the
plastic that may occur with power tools.
These screws will be reused.
5. Using the three original torx screws, install the SS3 and bracket onto the vehicle. Ensure
the lamps are oriented such that the DT connector is on the “bottom” of the lamp and the
SAE markings are readable when installed on the vehicle.
6. Plug the SS3 into the factory fog light harness using the included DT wire adapter.
Test function. If the light does not turn on, try ipping the connector 180°.