Direct Supply Panacea PAN-PL5500DF User manual

1-800-634-7328 DirectSupply.com
Panacea®
ATLAS FLOOR LIFT
MODELS PAN-PL5500DF, PAN-PL5500DP
Please keep and refer to this Owner’s Manual.
Owner’s Manual
Thank you for purchasing a Panacea®Atlas Floor Lift from Direct Supply Equipment & Furnishings®. Please read
this entire guide carefully and keep it for future reference. This guide will provide you with instructions, warnings,
warranty information and other important information about your lift. Share this information with those individuals
who will be assembling, using, servicing, and/or cleaning the product to help ensure it is cared for properly.

2
Table of Contents
INTRODUCTION..............................................................................................................4
Important Safeguards .................................................................................................4
Definitions & Symbols ...............................................................................................4
SAFETY WARNINGS & CAUTIONS..........................................................................5 - 7
General Guidelines......................................................................................................5
Operating Guidelines ..................................................................................................5
Positioning and Pinch Points.......................................................................................5
Lift Assembly .............................................................................................................5
Lift Operation .............................................................................................................5
Using the Slings..........................................................................................................6
Lifting the Resident ....................................................................................................6
Transferring the Resident............................................................................................6
Performing Maintenance ............................................................................................7
Electrical & Grounding ................................................................................................7
Disposal......................................................................................................................7
Radio Frequency Interference.....................................................................................7
ASSE M BLY ............................................................................................................... 8 - 11
Parts Identification......................................................................................................8
Unpacking...................................................................................................................8
Instructions.......................................................................................................... 9 - 11
OPERATION............................................................................................................12 - 15
Hand Pendant Controls............................................................................................. 12
Raising/Lowering the Boom ..................................................................................... 12
Opening/Closing the Legs ........................................................................................ 13
Emergency Release.................................................................................................. 14
Emergency Stop ....................................................................................................... 14
Charging the Battery................................................................................................. 15

3
1-800-634-7328 DirectSupply.com
LIFTING THE RESIDENT........................................................................................ 16 - 17
Positioning the Resident Lift..................................................................................... 16
Attaching a Sling....................................................................................................... 16
Lifting/Moving the Resident .............................................................................. 16 - 17
TRANSFERRING THE RESIDENT .........................................................................18 - 19
Transferring to a Commode Chair ............................................................................. 18
Transferring to a Standard Commode ....................................................................... 18
Transferring to a Bathing Unit ................................................................................... 19
Transferring to a Wheelchair ..................................................................................... 19
TROUBLESHOOTING ...................................................................................................20
MAINTENANCE .....................................................................................................21 - 24
Safety Inspection Checklist ......................................................................................21
Lift Lubrication..........................................................................................................22
Detecting Wear & Damage.......................................................................................22
Cleaning the Sling & Lift ...........................................................................................23
Lifting Actuator Replacement ...................................................................................23
Mast Pivot Bolt .........................................................................................................23
Cradle/Hanger Bar ....................................................................................................23
Base Adjustment ......................................................................................................24
Caster Replacement .................................................................................................24
TECHNICAL SPECIFICATIONS .....................................................................................25
LIMITED WARRANTY...................................................................................................26
CUSTOMER SERVICE...................................................................................................27

4
Introduction
Thank you for purchasing a Panacea®Atlas Floor Lift. In this owner’s manual, you’ll find important
information you should read before assembling or using this product. Please keep this manual for future
reference.
If at any time you do not understand how to use this product, or you suspect it may be damaged, DO
NOT USE and immediately contact the distributor that sold this product to you.
This owner’s manual is compiled from the latest specifications and product information available at the
time of publication. Changes may be made to this manual at any time. Contact your distributor for a
current copy of this owner’s manual.
Important Safeguards
• WARNING: When using battery-operated mechanical products, especially when children are present,
basic safety precautions should always be followed. Read all instructions before using and save for future
reference. Important information is highlighted by the terms in the Definitions & Symbols section.
• WARNING: This device is intended for indoor use under the supervision of licensed healthcare
professionals. Use this device only as instructed. This device may not be appropriate for all individuals.
Definitions & Symbols
NOTE: Indicates a tip.
CAUTION: Indicates correct operating or maintenance procedures in order to prevent damage to or
destruction of the equipment or other property.
WARNING: Calls attention to a potential danger that requires correct procedures or practices in order to
prevent personal injury.
•: Attention! Read the instructions.
PRODUCT or DEVICE: Your Panacea®Atlas Floor Lift
WE, US and OUR: Direct Supply Manufacturing, Inc.
“You” means the user, caregiver or any other individuals who will be using or servicing the product.
“Distributor” means the reseller or other entity from whom you purchased this product.
“Medical Professional”: The physician or other healthcare professional who is familiar with the user’s
medical history and current medical condition and is responsible for determining if this product is
medically appropriate for the user.
“Caregiver”: The individual(s) responsible for the care and needs of the user, such as a spouse, adult
family member or home health aide. The caregiver must be available at all times to provide the user with
physical and cognitive assistance and provide supervision as needed.
“User”: The individual who uses the device.

5
1-800-634-7328 DirectSupply.com
General Guidelines
• WARNING: Do not install, assemble, or operate this equipment without first reading and
understanding the instruction manual. If you are unable to understand the warnings, cautions or
instructions, contact a healthcare professional, dealer, or technical personnel before attempting to use
this equipment. Otherwise, damage or injury may occur.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
• WARNING: Before using this product, check all parts for shipping damage. If the product is damaged,
do not attempt to use it and contact your distributer.
Operating Guidelines
• WARNING: This lift is not intended to transport a resident. It is intended only to transfer a resident from
one utility (beds, chairs, commodes, etc.) to another. Injury or damage may occur if not used as intended.
• WARNING: Do not attempt to transfer a resident without prior approval from a medical professional.
Do not install, assemble or operate this equipment without first reading and understanding the
instruction manual and observing trained specialists perform a lift.
• WARNING: This lift has a maximum lifting capacity of 500 lbs.
• WARNING: People with disabilities must be watched closely when lifted and special care must be taken.
• WARNING: Only slings and accessories specifically verified for use with Direct Supply®resident lifts
should be used. Use of other manufacturers’ components or accessories may compromise the operation
of this lift.
• WARNING: If the resident lift becomes wet or exposed to extreme temperature or humidity prior to
use, ensure handgrips do not twist on resident lift handle. Damage or injury could occur.
• CAUTION: Avoid damage to the resident lift by keeping foreign objects from coming in contact with
the lift mechanism.
Positioning & Pinch Points
• WARNING: It is possible for a body part to be caught in a pinch point either between moving
mechanical parts or between moving and stationary parts of the product. When operating the lift, be
aware of the cradle/hanger bar position relative to the resident. Injury could occur.
Lift Assembly
• WARNING: DO NOT overtighten hardware. Product damage may occur.
Lift Operation
• WARNING: Before attempting to transfer, the user must be assessed by a qualified professional.
• WARNING: Only trained and qualified caregivers should transfer a person. Do not attempt to use the
lift if you have not been properly trained to do so.
• WARNING: Do not store the lift in a shower, bath or other area with high humidity.
• WARNING: Keep all lift components clean and dry and ensure electrical and mechanical safety.
• WARNING: Always maneuver the lift with the handles provided.
• WARNING: More than one assistant is recommended for all resident lift activities.
• WARNING: When mounting the battery on the charger, listen for an audible click to confirm proper
mounting. Otherwise, damage or injury could occur.
• WARNING: DO NOT exceed 500 lb. weight capacity.
• WARNING: Keep clear of moving parts to avoid injury while the lift is in operation.
Safety Warnings & Cautions

6
Safety Warnings & Cautions (cont.)
Using the Sling
• WARNING: For proper comfort and safety, use only a sling verified for use with this resident lift and
recommended by a medical professional.
• WARNING: DO NOT use any type of material between the resident and sling that may cause the
resident to slide out of the sling during transfer.
• WARNING: DO NOT modify slings in any way. Before each use, check sling attachments to ensure
proper connection.
• WARNING: If the resident is in a wheelchair, activate wheelchair wheel locks to prevent chair from
moving during transfers.
• WARNING: After each use or wash, inspect sling(s) for wear, tear and loose stitching. Bleached, torn,
cut, frayed or broken slings are unsafe and could result in injury. Discard and replace immediately.
• WARNING: When connecting slings equipped with color-coded straps to the resident lift, the shortest
straps MUST be at the back for proper support. The loops of the sling are color-coded to assist in connecting
both sides of the sling equally. Always ensure the resident’s head is properly supported during lifts.
Lifting the Resident
• WARNING: When lifting and lowering the resident, ensure legs on adjustable base are in the
maximum open position for optimal stability.
• WARNING: After elevating the resident a few inches above stationary object, ensure the sling and all
attachments are properly connected and secure. If any attachments are not correct, lower the resident
back onto the stationary object and correct this problem. Adjustments for safety and comfort should be
made before moving the resident. Ensure the resident’s arms are inside the straps.
• WARNING: Use of other manufacturers’ components or accessories may compromise the operation
and are not to be utilized as a component of this resident lift system.
• WARNING: During transfers with the resident suspended in a sling attached to the lift, DO NOT roll
caster base over uneven surfaces that could cause the resident lift to tip over. Always use the steering
handles on the mast to push or pull the resident lift.
• WARNING: When lifting a resident, DO NOT lock the rear casters. Doing so could cause the lift to tip
and could injure the resident or assistants. The rear casters should be left unlocked during lifting to allow the
resident lift to stabilize itself when the resident is initially lifted from a chair, bed or any stationary object.
Transferring the Resident
• WARNING: After elevating the resident a few inches above stationary object, ensure the sling and all
attachments are secure and properly connected. If any attachments are not correct, lower the resident
back onto the stationary object and correct this problem.
• WARNING: Before lowering the resident into wheelchair, ensure wheel locks are in a locked position.
• WARNING: Before transferring, ensure the resident’s weight does not exceed the 500 lb. weight
capacity of the resident lift.
• WARNING: Be sure to check the sling attachments each time the sling is removed and replaced to
ensure it is properly attached before the resident is lifted from the bed or chair.
• WARNING: Ensure mast is securely fastened for safety. All nuts, bolts, pins, and other attachments
must be checked at least every six months in conjunction with periodic maintenance.

7
1-800-634-7328 DirectSupply.com
Performing Maintenance
• WARNING: Maintenance MUST be performed ONLY by qualified personnel.
• WARNING: Ensure proper resident lift operation by performing regular maintenance. DO NOT
overtighten hardware. Product damage may occur.
• WARNING: After the first six months of operation, inspect all pivot points and fasteners for wear. If the
metal is worn, the parts MUST be replaced. Inspect these parts every six months thereafter.
• WARNING: After the first year of use, inspect the hooks of the cradle/hanger bar and the boom
mounting brackets every three months. Replace worn out parts as necessary. Inspect these parts every
six months thereafter.
• WARNING: Casters and axle bolts must be inspected every six months to check for tightness and
wear. NEVER use a resident lift if you suspect any portion of it is damaged or worn.
Electrical & Grounding
• WARNING: GROUNDING INSTRUCTIONS
The included battery charger should always be properly grounded to ensure resident and assistant safety. For
this reason, this device is equipped with a three-prong grounding plug to prevent possible shock hazards.
• WARNING: Avoid personal injury by making sure power is disconnected before conducting any
electrical inspection. Contact your distributor if any electrical problem is detected.
• WARNING: DO NOT alter, cut or remove the round grounding prong from this product. If a two-prong
wall receptacle is encountered, it is the customer’s responsibility to have the receptacle replaced by a
qualified electrician with a properly grounded three-prong wall receptacle in accordance with the National
Electrical Code and all local codes. If you must use an extension cord, use ONLY a three-wire extension
cord having the same or higher electrical rating as the device being connected, and verify the extension
cord is permitted in your community.
• WARNING: DO NOT remove warning tags located on your device. Carefully read battery/battery
charger information prior to installing, servicing or operating your resident lift
Disposal
• WARNING: This device contains lead acid batteries. DO NOT dispose of batteries in normal household
waste. They MUST be taken to a proper disposal site. Contact your local waste management company for
information. This product may contain substances that could be harmful to the environment if disposed of
in places (landfills) that are not appropriate according to legislation.
Radio Frequency Interference
• WARNING: Most electronic equipment is influenced by Radio Frequency Interference (RFI). CAUTION
should be exercised with regard to the use of portable communication equipment in the area around such
equipment. If RFI causes erratic behavior, PUSH the red power switch OFF IMMEDIATELY. DO NOT turn
the power switch ON while transmission is in progress.

8
Assembly
Unpacking
• WARNING: The lift components are heavy.
DO NOT attempt to remove lift from shipping
carton without assistance. Injury may occur.
Carefully unpack the components from the
shipping carton:
Parts Identification
1 Boom
2 Cradle/Spreader Bar
3 Mast
4Lifting Actuator
5a Base with Powered Width
Adjustment
5b Base with Manual Width
Adjustment
6 Hand Pendant
7 Battery/Control Box
8 Caster with Lock
9 Front Caster
10 Leg Actuator (Powered
Base Only)
Component Quantity
Base 1
Mast 1
Boom 1
6-Point Cradle/Hanger Bar 1
Lifting Actuator 1
Control Box 1
Battery 1
Hand Pendant 1
Hardware:
Carriage Bolts, 3⁄8" x 2¾" (3⁄8" x 70mm)
Hex-Head Bolts, M10 x 75mm L
Hex-Head Bolt, M10 x 50mm L
Nylon-Insert Lock Nuts, M10x1.5
Washers, M10
Black Plastic Hex Caps, M10
Clevis Pins + Key Rings
Socket Head Screw for Control Box
2
2
1
5
8
8
3
1
Charging Cable for Control Box 1
Optional Battery Charging Stand + Power Cord 1
5b
1
2
3
4
5a
6
7
8
9
10

9
1-800-634-7328 DirectSupply.com
Instructions Tools Required:
17mm Wrenches
#2 Philips Screwdriver
3mm Allen Wrench
1. Stand mast upright and place into sleeve on base.
2. Attach the mast to the base:
a. Align holes at bottom of mast with holes in sleeve on base (2 left-to-right, 2 front-to-rear).
b. Connect the mast to the base with the 8cm carriage bolts (x2), 8cm hex-head bolts (x2),
washers (x8), and lock nuts (x4).
c. Tighten using 17mm wrenches.
d. Ensure the bolts are secure and there is no movement between the mast and base.
e. Place the black caps (x6) over the bolt heads and nuts.
3. Attach the boom to the top of the mast:
a. Align the hole on the lifting arms with the mounting bracket at the top of the mast.
b. Connect the lifting arms to the mast with the 6cm hex-head bolt (x1), washers (x2) and lock nut (x1).
c. Tighten using a 17mm wrench. Do not overtighten so that the lift arms cannot rotate at the
connection point.
d. Place the black caps (x2) over the bolt head and nut.

10
Assembly (cont.)
4. Attach the cradle/spreader bar to end of boom:
a. Detach the key ring from the clevis pin.
b. Align the hole on the cradle with the mounting bracket at the end of the boom.
c. Insert pin and reattach key ring.
5. Attach the lifting actuator to the mounting brackets on
the mast and boom:
a. Detach the key rings from the clevis pins.
b. Align the actuator so that the actuator warning
label is facing toward the user in the sling and the
mounting holes at the top and bottom line up with
the holes on the mounting brackets.
c. Insert pins and reattach key rings.
6. Mount the control box to the mast:
a. Hang the control box mounting bracket on the two
screws on the rear face of the mast.
b. Use a #2 Phillips screwdriver to tighten the screws.
c. Attach the control box to the mounting bracket
using the socket-head screw and tighten using a
3mm Allen wrench.

11
1-800-634-7328 DirectSupply.com
7. Connect cables from the hand pendant and actuators to the ports on the bottom of the control box as
in the figure below.
• 1= Hand Pendant
• 2= Lifting Actuator
• 3= Base Legs Actuator (only for Powered Base Floor Lift)
8. The power/emergency stop button on the control box is compressed in the “Off” position. Release
the power button by twisting clockwise. This will turn on the control box. Verify the power indicator
light is on.
9. Install the battery onto the lift. Place the base of the battery on top of the control box. Push the top
lever onto the top edge of the control mounting bracket. Listen for an audible click.
10. Inspect the battery charge level on the control box display. Solid bars on the display indicate battery
charge level (0-100%). Ensure the battery has capacity for operation.
11. Test all actuator functions on the hand pendant and inspect all assemblies for proper operation.
Ensure all bolts are screwed tightly.
12.The lift is ready for use. Read this entire manual. Contact your distributer if you have any questions
regarding the proper assembly or use of this device.
1
2 3

12
Operation
• WARNING: Do not attempt to transfer the resident without prior approval from a medical professional.
Do not install, assemble or operate this equipment without first reading and understanding the
instruction manual and observing trained specialists perform a lift.
• WARNING: When lifting a resident, the legs of the lift must be in the maximum open position for
stability and safety. If it becomes necessary to maneuver the lift through a narrow space, only close
the legs of the lift enough to facilitate movement. When more space is available, return the legs to the
maximum open position.
• CAUTION: More than one assistant is recommended for all resident lift activities.
Raising/Lowering the Boom
• WARNING: When lifting a resident, DO NOT lock the rear casters. Doing so could cause the lift to tip
and could injure the resident or assistants. The rear casters should be left unlocked during lifting to allow
the resident lift to stabilize itself when the resident is initially lifted from a chair, bed or any stationary object.
• Press and hold the Up arrow on the hand pendant to raise the boom and resident.
• Press and hold the Down arrow on the hand pendant to lower the boom and resident.
Hand Pendant Controls
Raise/Lower Lift Press and hold Up
arrow to raise lift
Press and hold Down
arrow to lower lift
Open/Close Base Legs
(Powered Base Only) Press and hold to
open base legs
Press and hold to
close base legs

13
1-800-634-7328 DirectSupply.com
Opening/Closing the Legs
• WARNING: For optimal stability, operate this lift with the base legs in the open position when lifting
and lowering the resident.
Lift with Powered Base Adjustment:
• Ensure the rear casters are unlocked.
• Press and hold the Leg Open button on the hand pendant to open the legs on the base.
• Press and hold the Leg Close button on the hand pendant to open the legs on the base.
Lift with Manual Base Adjustment:
• Ensure the rear casters are unlocked.
• To open the legs, depress the right foot pedal. Hold onto the push handle for stability.
• To close the legs, depress the left foot pedal. Hold onto the push handle for stability.
Legs Open Legs Closed

14
Operation (cont.)
Emergency Release
Always use extreme caution when operating an emergency release.
Primary Emergency Release
To activate the primary emergency release, insert a pen into the hole labeled “EMERGENCY” on the control
box of the lift and push down on the boom at the same time.
This product’s lift actuator is equipped with a mechanical emergency release, which enables retraction
without electrical power. The actuator will only retract when the emergency release lever is pulled while
under load. Locate the emergency release red-colored grip lever.
Secondary Emergency Release
• CAUTION: The secondary emergency release is only a backup if
the primary emergency release fails. Use the primary release first.
If the primary release fails to function correctly or is out of reach,
the secondary emergency release may be used.
To activate the secondary release, pull up on the red-colored
emergency release lever to its maximum position, about 11 mm,
or when the red-colored lever can’t be pulled up any further, and
push down on the boom at the same time. Continue to lift the red
emergency release lever to its maximum position, and push down
on the boom until the boom has been fully lowered.
Emergency Stop
To stop the boom from raising or lowering, press the red emergency button on the control box.
To disengage the emergency stop, rotate the red emergency stop button clockwise.
Insert pen
here

15
1-800-634-7328 DirectSupply.com
Charging the Battery
NOTE: To prolong battery life, the battery should be recharged daily.
The battery can be charged via the control box:
• With the battery on the lift, plug the AC charging cable into the charging port on the bottom of the
control box.
• Plug the other end of the cable into the electrical wall outlet (120 V).
• Verify the CHARGE light is illuminated.
• When all 4 bars on the battery capacity display has solid fill, the battery is charged to 100%. Unplug the
AC charging cable from the wall outlet.
NOTE: The lift cannot be operated while the battery is charging via this method.
The battery can also be charged via the separate charging stand:
• Lift the handle on the back of the battery. Lift the battery up and away from the control box.
• Place the charging stand on a flat surface near an electrical wall outlet.
• Plug the AC charging cable from the charging stand into the electrical wall outlet. Verify the ON light
is illuminated.
• Set the battery on top of the charging stand. Verify the CHARGE light is illuminated.
• When charging is complete, the CHARGE light will turn off. The battery is now ready for use. It takes
approximately 4 hours for a battery to fully recharge.
Power/
Emergency
Stop
Primary
Emergency
Release
Power
Indicator
Battery
Charging
Indicator
Battery
Capacity
Display
Charging
Cable Port

16
Lifting the Resident
NOTE: Prior to first use, please make sure the battery has been charged for 24 hours in order to reach
proper function and prolong the battery life.
More than one assistant is recommended for all resident lift activities.
Positioning the Resident Lift
Refer to the Safety Warnings & Cautions section in this manual before proceeding further and observe all
warnings indicated. Before positioning the legs of the resident lift under a bed, make sure the area is clear
of any obstructions.
• WARNING: When lifting and lowering a resident, the legs of the lift must be in the maximum open
position for stability and safety. To facilitate movement of the lift during lift positioning and resident
transfers, the legs may in the open or closed position. Maximum open position is recommended for
optimal stability.
a) Depress the right foot pedal (for manual base lift) or press and hold the open legs button on the hand
pendant (for powered base lift) to open the legs of the resident lift to maximum width.
b) Use the steering handles to position the resident lift.
c) To lower the boom for easy attachment of the sling, press the DOWN arrow button on the hand pendant.
Attaching a Sling
a) Place the straps of the sling over the hooks of the cradle/hanger bar. Ensure the straps are contained
within the hooks by the spring-loaded clips.
b) Match the corresponding colors on each side of the sling so the sling is attached evenly.
c) Use the lift to move the resident. Refer to Lifting/Moving the Resident section.
d) The lift cradle/hanger bars have three hookup points per side. The middle hookup is ONLY used for
slings that have three sets of straps per side.
Lifting/Moving the Resident
a) Position the sling under the resident and place the resident’s arms inside the sling.
b) Press the UP arrow on the hand pendant to raise the resident high enough to clear the surface of the
bed. The resident’s weight will be fully supported by the resident lift.
c) When the resident is clear of the bed surface, swing the resident’s feet off the bed.
d) Use the steering handles to move the resident lift away from the bed.
e) When moving the resident lift away from the bed, turn the resident so he or she faces the assistant
operating the resident lift.
f) Press the DOWN arrow on the hand pendant to lower the resident until his or her legs straddle the mast
and his or her feet rest on the base of the resident lift.
g) Pull the resident lift away from the bed and then push the lift from the rear side of the mast with both
hands firmly on the steering handles.

17
1-800-634-7328 DirectSupply.com
• WARNING: DO NOT exceed the maximum weight capacity of 500 lbs.
• WARNING: Do not attempt to transfer the resident without prior approval from a medical professional.
• WARNING: Only slings and accessories verified for use with Direct Supply resident lifts should be
used. Use of other manufacturers’ components or accessories may compromise the operation of this
resident lift.
• WARNING: When lifting a resident, DO NOT lock the rear casters. Doing so could cause the lift to tip
and could injure the resident or assistants.
• WARNING: When lifting or lowering a resident, the legs of the lift must be in the maximum open
position for optimal stability and safety.
• WARNING: Perform resident transfers with the lift base legs in the maximum open position for
optimal stability. If it becomes necessary to transfer a resident through a narrow space, only close the
legs of the lift enough to facilitate movement. When more space is available, return the legs to the
maximum open position.
• WARNING: After elevating the resident a few inches above a stationary object, ensure the sling and
all attachments are secure and properly connected. If any attachments are not correct, lower the resident
back onto the stationary object and correct this problem. Otherwise, damage or injury could occur.
Adjustments for safety and comfort should be made before moving the resident. The resident’s arms
should be inside the straps.
• WARNING: Be sure to check the sling attachments each time the sling is removed and replaced to
ensure it is properly attached before the resident is removed from a bed or chair. Slings with commode
openings are designed to be used with either a commode chair or standard commode.
• CAUTION: Direct Supply recommends the sling remain connected to the cradle/hanger bar hooks
during the resident’s use of either the commode chair or standard commode.

18
Transferring the Resident
• WARNING: Do not attempt to transfer the resident without prior approval from a medical professional.
Transferring to a Commode Chair
a) Lift the resident from the bed. Refer to Lifting/Moving the Resident section.
b) Press the UP arrow on the hand pendant to lift the resident high enough to clear the arms of the
commode chair. Their weight will be supported by the resident lift.
c) Guide the resident onto the commode chair. This may require two assistants.
d) Press the DOWN arrow on the hand pendant to lower the resident onto the commode chair, leaving
the sling attached to the cradle/hanger bar hooks.
e) When complete, recheck the sling for correct attachments.
f) Press the UP arrow on the hand pendant to raise the resident off the commode chair.
g) When the resident is clear of the commode surface, use the steering handles to move the resident lift
away from the commode chair.
h) To return the resident to bed, reverse the steps in Lifting the Resident section.
i) To return or place the resident in a wheelchair, refer to Transferring to a Wheelchair section.
Transferring to a Standard Commode
• WARNING: This lift is NOT intended to transport a resident. It is intended only to transfer the resident
from one surface to another, such as from a bed to a commode. Injury or damage may occur if not used
as intended.
If the bathroom facilities are NOT near the bed or if the resident lift cannot be easily maneuvered towards
the commode, the resident MUST be transferred to a wheelchair and transported to the bathroom
facilities before using the resident lift again to position the resident on a standard commode. Refer to
Transferring to a Wheelchair section.
a) To ensure the resident lift can maneuver around the commode, use an empty resident lift to
confirm maneuverability.
b) Once confirmed the resident lift can maneuver around the commode, lift the resident from the bed.
Refer to Lifting the Resident section.
c) To elevate the resident high enough to clear the commode, press the UP/DOWN arrows on the hand
pendant. The resident’s weight will be supported by the resident lift.
d) Carefully guide the resident onto the commode. This may require two assistants.
e) Press the DOWN arrow on the hand pendant to lower the resident onto the standard commode leaving
the sling attached to the cradle/hanger bar hooks.
f) When complete, recheck the sling for correct attachments.
g) Press the UP arrow on the hand pendant to raise the resident off the commode.
h) When resident is clear of the commode surface, use the steering handle to move the lift away from
the commode.
i) To return the resident to bed, reverse the steps in Lifting/Moving the Resident section.
j) To return or place resident in a wheelchair, refer to the Transferring to a Wheelchair section.

19
1-800-634-7328 DirectSupply.com
Transferring to a Bathing Unit
a) Lift the resident from the bed. Refer to Lifting/Moving the Resident section.
b) To elevate the resident high enough to clear the portable bath tub, press the UP/DOWN arrows on the
hand pendant.
c) Slide the portable bath tub under the resident.
d) Press the boom down arrow to lower the resident into the portable bath tub.
e) Detach the sling from the cradle/hanger bar hooks.
f) Attach the portable bath tub straps to the resident lift.
g) Press the UP arrow on the hand pendant to raise the sides of the portable bath tub.
h) Bathe the resident.
i) Reverse this procedure to return the resident to bed.
Transferring to a Wheelchair
• WARNING: DO NOT place the resident in the wheelchair if the locks are not engaged. Before lowering
the resident into the wheelchair, the wheelchair wheel locks MUST be in a locked position. Otherwise,
injury can occur.
a) Lift the resident from the bed. Refer to Lifting/Moving the Resident section.
b) Ensure the legs of the lift with resident in the sling are in the maximum open position.
c) Move the wheelchair into position.
d) To prevent movement of the wheelchair, engage the rear wheel locks.
e) For proper positioning, guide the resident’s hips as far back as possible into the seat by using the
straps or handles on the side and the back of the sling.
f) Position the resident over the seat with their back against the chair back.
g) Begin to lower the resident by pressing the DOWN arrow on the hand pendant.
h) Two assistants are recommended for this step – one assistant stands behind the chair and the other
operates the resident lift. The assistant behind the chair pulls back on the grab handle on the sling (on
select models) or pulls back on the sides of the sling to seat the resident against the wheelchair back.
This will help maintain a good center of balance. Take care to prevent the chair from tipping forward.
i) Leave the sling in place unless a divided leg sling was used. Remove a divided leg sling.
j) Reverse Lifting the Resident section to return to the seating surface of the wheelchair.

20
Troubleshooting
Problem Possible Cause Corrective Action
Cannot lift patient up and
battery indicator light is off.
Battery not connected to control box.
The fuse has blown.
Control box defective.
Charge the battery.
Reconnect battery to control box.
Replace fuse, if the system is prepared
for external fuse replacement, or send
the system to repair.
Replace control box.
Power indicator lights up and
battery shows charge, but lift
actuator does not run.
Hand pendant connection to control
box is loose.
Lift actuator connection to control box
is loose.
Control box defective.
Hand pendant defective.
Check connection between hand
pendant and control box
Check connection between lift actuator
and control box
Replace control box.
Replace hand pendant.
Power indicator lights up and
battery shows charge, but
base legs will not open/close
(powered base only)
Hand pendant connection to control
box is loose.
Leg actuator connection to control box
is loose.
Control box defective.
Hand pendant defective.
Check connection between hand
pendant and control box
Check connection between leg
actuator and control box
Replace control box.
Replace hand pendant.
Power indicator lights up, but
actuator does not run.
Relays in control box are
heard clicking.
Actuator plug not pushed into control
box properly.
Actuator defective.
Control box defective.
Push actuator plug into control box
securely.
Replace actuator.
Replace control box.
No relay noise is heard from
control box.
Handset plug not properly connected.
Emergency stop engaged.
Check all cord connections.
Deactivate emergency stop.
Control box will not turn on
with battery installed and no
relay clicking is heard.
Battery completely discharged.
Battery defective.
Charge battery.
Replace battery.
Control box working in one
direction on one channel.
Handset defective.
Control box defective.
Replace hand control.
Replace control box.
Noisy or grinding sound from
pivot locations. Loss of lubrication. Lubricate using light oil.
Boom/lift arm will not lower
from uppermost position.
Boom/lift arm requires a minimum
weight load to lower from the
uppermost height position.
Pull down slightly on the boom/ lifting
arm to lower.
Boom/lift arm will not lower
when mechanical emergency
release lever is actuated.
Boom/lift arm requires a minimum
200 lb. weight load to lower from
the uppermost height position when
emergency release is activated.
Pull down with full weight on the
boom/lift arm to lower.
Charge light not on while
battery is charging via the
control box
Emergency stop engaged.
Charging cable connection to control
box is loose.
Charging cable or plug is damaged.
Deactivate emergency stop.
Check charging cable connection to
control box.
Replace charging cable.