Directed 933.TL7 User manual

DS3+ / DS4+ 933.TL7
v2.39.198.9
2016 Toyota 4Runner (G Key)
THTON10, THTON5 Compatible
(Sold Separately)

Introduction 3
Vehicle function compatibilities 4
Pre-installation and application warnings 5
Key type 5
Installation 6
Wiring diagram with T-Harness (THTON5) 6
Wiring diagram with T-Harness (THTON10) 7
Wiring diagram 8
Locating components in the vehicle 9
Vehicle connections 10
Module programming 13
Important! The master key is required to complete the module programming successfully. 13
Module programming for convenience only (skip transponder) 14
Module programming for security-only installations 15
Pairing remotes 16
Connecting the module 16
8556T Temperature Sensor 16
8504D Combo Sensor 16
RF Systems 16
When used in conjunction with SmartStart 17
D2D port configuration 17
Manual transmission 18
LED diagnostics and troubleshooting 19
Soft reset 21
Hard reset 21
Tach learning procedure (not needed with Virtual Tach) 22
Initializing Virtual Tach (not needed with hardwired or data tach applications) 22
Limited lifetime consumer warranty 23
Quick Reference Guide (customer copy) 24
Contents

3933.TL7 2.39.198.9 2016 Toyota 4Runner (G Key)
©2023 VOXX•DEI LLC. All rights reserved.
Introduction
This guide provides information on the installation of the DS3/DS3+ and DS4/DS4+ modules as a digital solution. Using these modules in a
digital configuration require the module to be flashed with vehicle specific firmware. Refer to our website (www.directechs.com) and click on
the DIRECTLINK text in the header for additional information.
DS3/DS3+ and DS4/DS4+ modules provide an all-in-one solution for most modern vehicles, and include remote start, keyless entry, security,
and immobilizer bypass capabilities. T-harnesses may also be used in many applications for easy installation.
The following methods are available to configure modules:
• Web: www.directechs.com (DS3/DS3+ and DS4/DS4+)
• Desktop Application: Directlink DT (DS3/DS3+ and DS4/DS4+)
• Mobile Device: Directlink App (DS4/DS4+ only)
When Flashing via Directlink DT (Desktop app) or via the Web, an XKloader2 will be required.
To configure via Web or DirectLink DT (mobile app):
1. Disconnect the main module from any (+) 12V power source.
2. Connect the module to your computer using the XKLoader2.
3. Follow the steps in the pop-up window that will be displayed when the module is detected.
Notes:
•Flashing via web is only possible using Internet Explorer on Windows 8, 8.1, and 10.
•This method is not compatible with any other browser (Edge, Chrome, Firefox, etc.)
•When using Windows 11 or newer, Directlink DT is mandatory.
The DS4/DS4+ module is designed to be configured using the DirectLink application through mobile devices.
To download the DirectLink mobile application, visit the Google Play or Apple store. They can also be
configured via Web and DirectLink DT. The DS4/DS4+ features are built in Bluetooth® 4.0, allowing you to
configure and control your system. The DS3/DS3+ module is not equipped with Bluetooth®, therefore is not
compatible with the DirectLink app for mobile devices.
To configure via DirectLink DT (mobile app):
1. Follow and complete the wiring diagram(s) related to your installation through the app.
2. When installation is complete, select Configure DS4/DS4+.
3. Follow the on-screen instructions.
FLASH REQUIRED!
FLASH REQUIRED!
4 White

4933.TL7 2.39.198.9 2016 Toyota 4Runner (G Key)
©2023 VOXX•DEI LLC. All rights reserved.
Vehicle function compatibilities
This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart.
Parking Lights Control
Arm Factory Security
Disarm Factory Security
Door Lock Control
Door Unlock
Driver Priority Unlock
Trunk / Hatch Release
DS4+/DS3+/VSM3 Only
Fuel level/EV battery level
* Odometer
Immobilizer Bypass-Data No Key Req'd
3x LOCK START (Start control using OEM Remote)
Accessory Activation
Ignition Activation
RAP Shut Down (Retained ACC Power)
Remote Start Takeover
SmartStart
Start (Crank) Activation
Tach / RPM Output
Entry Monitoring ALL Door Pins
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Factory Alarm Trigger Monitoring
Brake Status (foot brake)
Door Locks Status
E-Brake Status
Ignition Status

5933.TL7 2.39.198.9 2016 Toyota 4Runner (G Key)
©2023 VOXX•DEI LLC. All rights reserved.
Pre-installation and application warnings
START HERE This section highlights important information for this specific firmware and will assist in pricing accordingly, as
well as bringing awareness to any operational or vehicle limitations.
Compatibilities and Requirements
T-Harness
compatible THTON5 or THTON10 Keys required for
programming 1Keys required for operation 0
Vehicle Takeover Refer to the Quick Reference Guide section for more details.
Firmware notes
Important! The master key is required to complete the module programming successfully.
A DS4+ module is required for this installation, as the Relay harness (H2), 10-pin white connector is used.
Keysense: Do not connect the keysense wire in the installation for each of these vehicles or you will encounter issues when
attempting to start the vehicle.
T-Harness (THTON5 or THTON10):
•All T-Harness wires not listed in the diagram are not required for the installation. Loose wires such as Siren Output and
Hood Input may need to be pulled from the tapped section of the T-harness. Refer to the "wiring diagram with T-Harness"
for more information on connections and installation instructions.
•The optional Plug & Play THTON5 or THTON10 T-Harness is sold separately.
•The OBDII Diagnostic Connector features will remain the same even when the T-Harness is installed.
•All T-Harness wires not listed in the diagram are not required for the installation.
Fuses: It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed on each
wiring diagram.
All connectors are displayed from the wire side (unless specified otherwise).
Refer to the Vehicle connections following the installation diagram.
Footnotes
[1] Hood pin: The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin or if
not supported in data.
[2] Siren: Only required when enabling the security features during module flashing.
[3] Green wire: Only required for starter disable and antigrind applications.
[4] Autolights Interrupt: Only required if vehicles are equipped with autolights.
[5] Parking light output: Only required if parking lights are not supported in data.
Key type
Some Toyota 2010+ models have different encryption types. Please look at your key blade and identify the markings.
G-stamped keys Standard Key H-stamped keys
H
For vehicles with H-stamped keys, see
the TL10 firmware.
For vehicles with G-stamped keys, see
the TL5 & TL7 firmware.
For vehicles with dot-stamped keys,
see the TL11 firmware.
Note: Some replacement keys
may not have any markings on
the key.

6933.TL7 2.39.198.9 2016 Toyota 4Runner (G Key)
©2023 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Wiring diagram with T-Harness (THTON5)
456
161718 131415
10
11
12
1
23
789
19
Autolights: Pin 19
(-) Parking Lights: Pin 18
20
Headlight
Switch
Autolights Interrupt (conn. side): Lt. Green
Autolights Interrupt (veh. side): Lt. Green/White
Ignition Connector
RDA: Orange/Black
THTON5
(optional T-Harness)
Diagnostic Connector OBDII
16
8
9
1
CUT
(-) Hood Input: Gray: 21
(+) Siren Output: Brown/Red: 11
(-) Parking Lights Output: Lt.Green/Black: 1
Siren
Hood Pin
Parking Light: Lt. Blue/Black
Lt. Blue/Black Parking Light
Refer to the Vehicle connections section
for more specific T-harness compatibility.
Body ECU Connector
Refer to the “Vehicle connections”
section for wire and connector
details.
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
IMPORTANT:
Position the
fuses correctly!
Slide to open
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
5
30
20
20
15
10-pin White Connector
8-pin White Connector
12-pin Black Connector

7933.TL7 2.39.198.9 2016 Toyota 4Runner (G Key)
©2023 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Cut the
Orange/Green and
Orange/Brown loops
labeled CAN2.
Wiring diagram with T-Harness (THTON10)
Main
Body
ECU
(Back)
Siren
Hood Pin (-) Hood Input: Gray
(+) Siren Output: Brown/Red
THTON10
(optional T-Harness)
Cut the
Dk. Green/Black and
Dk. Blue/Black loops
labeled Lock/Unlock.
10-pin White Connector
Cut the
Violet/White loop
labeled Tach.
12-pin Black Connector
Ignition Connector
Diagnostic Connector OBDII
Body ECU Connector
(middle conn. left side of
steering column)
8-pin White Connector
22-pin White Connector
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
IMPORTANT:
Position the
fuses correctly!
Slide to open
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
5
30
20
20
15
Steering Lock
(black 7-pin connector)
NOT USED
IMPORTANT
Programming error
can occur if the 7-pin
connector is used.

8933.TL7 2.39.198.9 2016 Toyota 4Runner (G Key)
©2023 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Wiring diagram
Autolights Interr. (conn. side): Lt. Green: 8
Autolights Interr. (veh. side): Lt. Green/White: 9
(-) Ground: Black: 10
(+) Starter 2 Output: White: 5 & 11
HS CAN Low: Tan: 1
HS CAN High: Tan/Black: 2
RDA: Orange/Black: 7
SIL Data Output: Yellow/Black: 8
Siren
Hood Pin
(+) 12V Input: Red: 6 & 12
(-) Hood Input: Gray: 21
(+) Siren Output: Brown/Red: 11
RDA
16
8
9
1
Diagnostic Connector OBDII
Headlight
Switch
HS CAN Low:
Pin 14
HS CAN High:
Pin 6
SIL DATA:
Pin 7
456
161718 131415
10
1112
123
789
1920
(-) Parking Lights Output: Lt.Green/Black: 1
(-) Parking Lights: Pin 18
Autolights: Pin 19
(+) Ignition Input/Ouput: Pink: 10
(+) 12V Input: Red: 5
(+) Accessory Output: Orange: 8
(+) 12V Input: Red/White: 9
(+) 12V Input: Red/Black: 2
(+) Ignition 2 Output: Pink/White: 4
(+) Starter Output (veh. side): Violet: 7
Starter Input (conn. side): Green: 6
67
1234
85
(+) Ignition 2:
Pin 4
(+) Ignition 1: Pin 6
(+) Accessory: Pin 3
(+) Starter 2: Pin 1
(+) 12V: Pin 7
Ignition
Connector
(+) Starter 1:
Pin 8
CUT
CUT Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
IMPORTANT:
Position the
fuses correctly!
Slide to open
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
5
30
20
20
15
Body ECU Connector
Refer to the “Vehicle connections”
section for wire and connector
details.

9933.TL7 2.39.198.9 2016 Toyota 4Runner (G Key)
©2023 VOXX•DEI LLC. All rights reserved.
Locating components in the vehicle

10 933.TL7 2.39.198.9 2016 Toyota 4Runner (G Key)
©2023 VOXX•DEI LLC. All rights reserved.
Vehicle connections
The connection information listed below is specific to the 2016 Toyota 4Runner (G Key). Refer to “Pre-installation and application warnings” for a list of important notes.
Data harness, 8-pin white connector (H1)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H1/1 Tan (Data) HS CAN Low OBD-Data Link Connector, white 16 pin plug, pin 14 Data White Mandatory
H1/2 Tan/Black (Data) HS CAN High OBD-Data Link Connector, white 16 pin plug, pin 6 Data Violet Mandatory
H1/3 Orange/Brown No Connection No Connection
H1/4 Orange/Green No Connection No Connection
H1/5 Lt. Green No Connection No Connection
H1/6 Violet/Brown No Connection No Connection
H1/7 Orange/Black (Data) RDA Body ECU on dash fuse box, white 30 pin plug, pin 26 Data Pink Mandatory
H1/8 Yellow/Black (Data) SIL OBD-Data Link Connector, white 16 pin plug, pin 7 Data Green Remote Start
Only
Analog input/output harness, 22-pin white connector (H2)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H2/1 Lt. Green/Black (-) Pk Light Output [5] Headlight Switch, white 20 pin plug, pin 18 - Red
H2/2 Blue/White No Connection No Connection
H2/3 Dk. Green/Black No Connection No Connection
H2/4 Red/White (-) Trunk Output No Connection
H2/5 Brown/Black (-) Horn Output Horn Switch --or-- Dash Fuse Box, white 40 pin plug (2D), pin 29 - Gray to Gray/Blue Optional
H2/6 Brown/White No Connection No Connection
H2/7 White (+) No Connection No Connection
H2/8 Violet/Black No Connection No Connection
H2/9 Dk. Blue/Black No Connection No Connection
H2/10 Lt. Blue/Black No Connection No Connection
H2/11 Brown/Red (+) Siren Output [2] Security Only
H2/12 Pink No Connection No Connection
H2/13 Violet No Connection No Connection
H2/14 Brown No Connection No Connection
H2/15 White/Blue No Connection No Connection
H2/16 Red/Blue No Connection No Connection
H2/17 Black/White No Connection No Connection
H2/18 Orange/Black No Connection No Connection
H2/19 Blue No Connection No Connection
H2/20 Green No Connection No Connection
H2/21 Gray (-) Hood Switch Input [1]
H2/22 Violet/White No Connection No Connection