DMP Electronics XR500 SERIES User manual

XR500 Series Update
March 2005
Version 108 Software
Effective March 2005, all XR500 Series panels are being manufactured with version 108 (3/1/05)
software. This version is an update from the 106 (1/4/05) software previously shipped and contains
new features.
New Features
Multi-Lingual Option
The XR500 Series panel now provides the option in System Options to view the Programming and User
menus in multiple languages.When more than one language is programmed, the installer or user is
prompted to choose the language to display.
PROG LANGUAGE
Programming Menu Language
Press the COMMAND key to select the programming language(s). Any changes
in PROG LANGUAGE do not take effect until the STOP routine completes.
PRI LANG: ENGLSH
The current primary programming language is displayed. The default language
is English. Press a Select key to change the primary programming language.
ENG SPN
Select the primary programming language.
ENG = English
SPN = Spanish
SEC LANG: NONE
The current secondary programming language is displayed. Selecting a
secondary language allows the installer to view programming in English or
Spanish. When the Programming Menu is accessed, the installer is prompted to
choose the programming display language. If SEC LANG: is set to NONE, the
option to choose a language does not display. To select a secondary language,
press the Select key below the language. Default is NONE.
NONE ENG SPN
Select the secondary programming language.
NONE = No secondary language options are displayed
ENG = English
SPN = Spanish
USER LANGUAGE
User Menu and Status List Language
Press the COMMAND key to select User language(s).
PRI LANG: ENGLSH
The current primary user language is displayed. The default language is
English.
Press a Select key to change the primary User language.
ENG SPN
Select the primary user language.
ENG = English
SPN = Spanish

TU
-
0317 © 2005 Digital Monitoring
Products
SEC LANG: NONE
The current secondary user language is displayed. Selecting a secondary user
language allows the user to view the User Menu and Status List text in English
or Spanish. When the User Menu is accessed, the user is prompted to choose
the display language. Status List text displays in the selected language until
another language is chosen. If SEC LANG: is set to NONE, the option to choose
a language does not display. To select a secondary language, press the Select
key below the language. Default is NONE.
For example, when Spanish is selected at a keypad, the User Menu and Status
List text display in Spanish at that keypad. When the user later accesses the
keypad, pressing the COMMAND key once displays the option for English or
Spanish. Pressing the COMMAND key again continues to display the Status List
text in Spanish. Later on, if English is selected at that keypad, the User Menu
and Status List text display in English at that keypad.
NONE ENG SPN
Select the secondary user language.
NONE = No secondary language options are displayed
ENG = English
SPN = Spanish
Arm First Option
The XR500 Series panel now provides the option in Area Information to program an area to
automatically arm when any other area is armed from a keypad.
ARM FIRST NO YES
Arm First Area
Select YES to enable this area to operate as an Arm First area. This area is
automatically armed when any non-Arm First area assigned to the same
keypad is armed but does not disarm when other areas become disarmed.
Assign areas to keypads using the Display Areas option in Device Setup
programming. You can have multiple Arm First areas in a system and divide
them among keypads if needed. If an Arm First area has faulted zones that
cannot be bypassed, arming stops and the areas are not armed. Correct the
problem with the Arm First area and then begin the arming process again.
Default value is NO.
Note: The Arm First automatic arming only occurs when arming from a
keypad. Arming from a zone, schedule, or remotely is not affected and Arm
First areas do not automatically arm.
User Codes
The XR500 Series panel now allows six-digits to be programmed for user codes. These six-digit user
codes can be used when manually entered at a keypad or entered from a card reader attached to a 734
Access Control Module. User Codes entered by the user from card readers attached to keypads and the
733 Access Control Module continue to accept a maximum five-digit codes only.

Closing Wait Output
The XR500 Series panel now provides a Closing Wait Output in Output Options just after the Sensor
Reset Output that turnson when a closing message is successfully sent to the receiver.
CLS WAIT OUT: 0
Closing Wait Output
Enter the output number to turn on for approximately four (4) seconds when
Closing Wait is programmed as YES and the panel successfully communicates
the closing message at arming. If the closing message does not communicate
successfully, this output does not turn on. Enter zero to disable this output.
Cancel Ambush Option
The XR500 Series panel now provides a Cancel Early Morning Ambush message (C) for a zone Alarm
Action in Zone Information programming. This zone action cancels a running Early Morning Ambush
timer.
A T L -
ALARM -Select A to send an alarm report to the receiver and activate the bell
output according to zone type. The zone name appears in the panel alarmed
zones and status lists.
TROUBLE -Select T to send a trouble report to the receiver. The zone name
appears in the panel alarmed zones and status lists.
Note: UL requirements prevent the Alarm (A) and Trouble (T) action for Fire
(FI), and Fire Verify (FV) zone types from being changed.
LOCAL -When you select L, an alarm report is NOT sent to the receiver. The
bell output activates and the zone name appears in the panel alarmed zones
and status lists.
-(Dash) -When you select a –(dash), reports are NOT sent to the receiver.
The bell output does not activate and there is no display in the panel alarmed
zones or status list. Only the relay output selected in the next section
operates.
D S C
CANCEL AMBUSH -Select C for the zone to cancel the Early Morning Ambush
timer and stop an Ambush message from being sent to the receiver. Faulting
the zone takes the place of a second user code being entered at the keypad
and is only available for non-fire type zones. Area assignment for the zone
does not affect this option. See Early Morning Ambush in Area Information
programming.

TU
-
0317 © 2005 Digital Monitoring
Products
New Feature Available for Purchase
Service User Authentication –Feature Key 105
The XR500 Series panel now offers the ability to authenticate service personnel with the SCS-1R
receiver before allowing access to panel programming or performing any user operations.
SVC USER AUTH
Service User Authentication
DISABLED
This feature offers the ability to authenticate service personnel before
allowing access to panel programming or performing any user operations.
When this feature is enabled and a valid Service User code is entered for
system operation or 6653 is entered for programming, the Service Code entry
option displays.
SVC CODE:
When the service person enters the Service Code, the panel authenticates the
code with the Service Code preprogrammed in the SCS-1R receiver, and access
to panel programming or the User Menu is granted. The Service Code can be
used for system operation for 30 minutes before authenticating again. If the
code entered is not validated, access to programming or the User Menu using
the Service User code is denied.
Note: The Service User code is user number zero (0) and can only be created
in the panel remotely.
Note: The SCS-1R receiver must have firmware version 902 or higher to
authenticate service personnel.
Purchasing Feature Upgrades
To purchase a feature upgrade, you may contact DMP Customer Service with the feature you would like
to enable and the panel serial number. The serial number(s) should be sent in writing via e-mail or fax.
A separate feature key is issued for each panel. The feature key only enables the requested feature on
the specified panel.
The panel serial number can be located in several different ways:
Printed on a label located on the right side of the XR500 PCB.
Using panel diagnostics. See the Appendix in the XR500 Series Programming Guide (LT-0679).
Using Remote Link (version 1.18 or higher)
—Initial panel connection screen displays panel serial number when you connect.
—New System Information screen displays all enabled panel features.
—The Panel>Feature Upgrade screen displays panel model, enabled panel
features, and panel serial number.
Ordering the New Software
XR500 Series software update version 108 (3/1/05)is available for download free of charge on the DMP
Dealer Direct Website at http://dmp.com/dealer.
Note: Remote Link Version 1.22 or higher is required to support the panel version 108 features. Remote
Link Version 1.22 is available for download free of charge on the DMP Dealer Direct Website at
http://dmp.com/dealer.