DMP Electronics PC0128 User manual

InstallatIon GuIde
Xt serIes™ Panels

MODEL XT30/XT50
XT SERIES™
INSTALLATION GUIDE
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changesormodicationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser’s
authority to operate the equipment.
This device has been designed to operate with the 1100 Series antenna listed in the Accessory Devices section,
and having a maximum gain of 1.8 dB. Antennas not included in this list or having a gain greater than 1.8 dB are
strictly prohibited for use with this device. The required antenna impedance is 50 ohms.
If necessary, the installer should consult the dealer or an experienced radio/television technician for
additionalsuggestions.Theinstallermayndthefollowingbooklet,preparedbytheFederalCommunications
Commission, helpful:
“How to identify and Resolve Radio-TV Interference Problems.”
ThisbookletisavailablefromtheU.S.GovernmentPrintingOfce,WashingtonD.C.20402
StockNo.004-000-00345-4
Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)
Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,
including interference that may cause undesired operation.
Industry Canada Information
ThisdevicecomplieswithIndustryCanadaLicence-exemptRSSstandard(s).Operationissubjecttothe
followingtwoconditions:(1)thisdevicemaynotcauseinterference,and(2)thisdevicemustacceptany
interference, including interference that may cause undesired operation of the device.
LeprésentappareilestconformeauxCNRd’IndustrieCanadaapplicablesauxappareilsradioexemptsde
licence.L’exploitationestautoriséeauxdeuxconditionssuivantes:(1)l’appareilnedoitpasproduirede
brouillage,et(2)l’utilisateurdel’appareildoitacceptertoutbrouillageradioélectriquesubi,mêmesile
brouillageestsusceptibled’encompromettrelefonctionnement.
©2013DigitalMonitoringProducts,Inc.
InformationfurnishedbyDMPisbelievedtobeaccurateandreliable.
Thisinformationissubjecttochangewithoutnotice.

XT30/XT50 Installation Guide Digital Monitoring Products
i
Table of ConTenTs
Panel Specications
1.1 Power Supply .........................................1
1.2 Communication.......................................1
1.3 Panel Zones............................................1
1.4 Keypads/Expansion.................................1
1.5 Number of Zones....................................1
1.6 Outputs..................................................1
1.7 EnclosureSpecications ..........................1
Introduction
2.1 SystemCongurations.............................2
2.2 Caution Notes.........................................2
2.3 Compliance Instructions..........................2
System Components
3.1 WiringDiagram.......................................2
3.2 LightningProtection ................................2
3.3 AccessoryDevices...................................2
3.4 XT30/XT50WiringDiagram .....................5
Installation
4.1 MountingtheEnclosure...........................6
4.2 MountingKeypads ..................................7
4.3 InstallationSpecications ........................7
Primary Power Supply
5.1 AC terminals 1 and 2...............................7
5.2 Transformer Types ..................................7
5.3 PowerLED .............................................7
Secondary Power Supply
6.1 Battery Terminals 3 and 4........................8
6.2 EarthGround..........................................8
6.3 Replacement Period ................................8
6.4 Discharge/Recharge ................................8
6.5 BatterySupervision .................................8
6.6 XT30/XT50 Power Requirements..............8
6.7 XT30/XT50 Standby Battery Calculations ..9
Bell Output
7.1 Terminals 5 and 6.................................10
Keypad Data Bus
8.1 Description...........................................10
8.2 Terminal7-RED...................................10
8.3 Terminal 8 - YELLOW ............................10
8.4 Terminal9-GREEN...............................10
8.5 Terminal 10 - BLACK .............................10
8.6 KeypadBusLEDs ..................................10
8.7 ProgrammingConnection ......................10
8.8 KeypadAddressing................................10
8.9 OvercurrentOVCLED............................11
Smoke and Glassbreak Detector Output
9.1 Terminal 11..........................................11
Burglary Zones
10.1 Description...........................................11
10.2 Operational Parameters.........................11
10.3 Zone Response Time.............................12
10.4 KeyswitchArmingZone .........................12

Digital Monitoring Products XT30/XT50 Installation Guide
ii
Table of ConTenTs
Powered Zone for 2-Wire Smoke Detectors
11.1 Terminals 25 and 26..............................12
Annunciator Outputs
12.1 Description...........................................12
12.2 HarnessWiring .....................................12
12.3 Model 860 Relay Module........................12
Telephone RJ Connector
13.1 Description...........................................13
13.2 FCCRegistration ...................................13
13.3 Notication...........................................13
Ethernet Connector J1
14.1 Description...........................................13
14.2 EthernetLEDs ......................................13
Reset Header J16
15.1 Description...........................................14
Flash Load Jumper J18
16.1 Description..........................................15
Cellular Connections
17.1 Cellular ...............................................15
On-Board 1100 Series Wireless Antenna Connection
18.1 Wireless Antenna .................................16
18.2 LEDOperation ......................................16
Wireless Keypads
19.1 MountingKeypads ................................16
19.2 Wireless Keypad Association..................16
Listed Compliance Specications
20.1 Introduction .........................................17
20.2 Bypass Reports.....................................17
20.3 CurrentDraw........................................17
20.4 Battery Standby....................................17
20.5 Auxiliary and Bell Current ......................17
20.6 CrossZoning ........................................17
20.7 SoftwareVersion...................................17
20.8 App Key ...............................................17
Household Burglar-Alarm System Units
ANSI/UL 1023
21.1 Bell Cutoff............................................17
21.2 EntryDelay ..........................................17
21.3 ExitDelay.............................................17
21.4 Wireless External Contact......................17
21.5 WirelessSupervisionTime .....................17
21.6 Wireless Audible Annunciation ...............17
21.7 Panel location.......................................17
21.8 Test Frequency.....................................17
Digital Burglar Alarm Communicator System Units
ANSI/UL 1635
22.1 EntryDelay ..........................................17
22.2 ExitDelay.............................................17
22.3 Test Frequency.....................................17
22.4 Automatic Bell Test ...............................17

XT30/XT50 Installation Guide Digital Monitoring Products
iii
Table of ConTenTs
Central Station Burglar Alarm Units
ANSI/UL 1610
23.1 Central Station......................................18
23.2 RemoteDisarm.....................................18
23.3 Central Station......................................18
Household Fire Warning System
ANSI/UL 985 NFPA 72 Specications
24.1 BellOutputDenition ............................18
24.2 HouseholdSystem ................................18
24.3 HouseholdFireWarning ........................18
24.4 WirelessSupervisionTime .....................18
24.5 WirelessFireVerication........................18
24.6 Battery Standby....................................18
24.7 AlarmVerication..................................18
24.8 Model 860............................................18
24.9 Test Frequency.....................................18
California State Fire Marshal Specications
25.1 BellOutputDenition ............................18
False Alarm Reduction Programmable Options
ANSI/SIA CP-01-2010
26.1 ShippingDefaultsand
 RecommendedProgramming .................19
26.2 CallWaiting ..........................................20
26.3 EntryDelay ..........................................20
26.4 Local Bell .............................................20
26.5 Minimum Installation Requirements........20
Troubleshooting
27.1 TroubleshootingSection ........................21
27.2 CommonLCDKeypadDisplays...............21
Wiring Diagrams
28.1 MultipleIndicatingCircuit
Modules Installation..............................22
28.2 SystemSensor2-WireSmokeDetectors .23
Revisions to This Document
Listings and Approvals

XT30/XT50 Installation Guide Digital Monitoring Products
1
Panel sPecifications
Panel Specications
1.1 Power Supply
TransformerInput: Plug-in—16.5VAC40VA,Model321
   Wire-in—16.5VAC40VA,Model320
StandbyBattery: 12VDC,1.0AmpsMax.chargingcurrent
   Models364,365,366,368,or369
   Replaceevery3to5years
AuxiliaryOutput: 12VDCat500mA
   12VDCat325mAwhenusedwithtwoModel364batteriesintheModel341enclosure
BellOutput:  12VDCat1.5Amps
SmokeDetectorOutput: 12VDCat100mA
All circuits inherent power limited
Note:PleaseseetheListedComplianceSpecicationssectionforcerticatedapplicationrequirements.
1.2 Communication
Built-inSDLCDigitalDialercommunicationtoDMPModelSCS-1RReceivers
Built-innetworkcommunicationtoDMPModelSCS-1RorSCS-VRReceivers
Built-inormodularcellularcommunicationtoDMPModelSCS-1RorSCS-VRReceivers
Built-inCID(ContactID)dialercommunicationtoDMPModelSCS-1RReceivers
1.3 Panel Zones
Nine1kOhmEOLburglaryzones:zones1to9
One3.3kOhmEOLClassBpoweredrezonewithresetcapability:zone10
1.4 Keypads/Expansion
Connectuptoeightsupervisedalphanumerickeypads.
Connectuptofouralphanumeric9000Serieswirelesskeypads.
Eightkeypadstotalperpanel.
Connectadditionalunsupervisedkeypads.
• GraphicTouchscreen,Thinline™,Aqualite™,ClearTouch™,andIconkeypads
Inaddition,thefollowingzoneexpanderscanbeadded:
• One,four,eightand16-zoneexpansionmodules
• Single-zonePIRandglassbreakdetectors
1.5 Number of Zones
• Onboardzones1-10
• Eightkeypadbusaddresseswithzones11-14,21-24,31-34,41-44,51-54,61-64,71-74,and81-84
• Zonenumbers31to34and41to44cansupport1100SeriesKeyFobsorDMPwirelessoutputmodules
• XT50has20additionalonboardwirelesszonesnumbered80-99
1.6 Outputs
TheXT30/XT50panelsprovidefouropencollectoroutputsratedfor50mAeach.AModel300OutputHarness
is required. The open collector outputs provide the ground connection for a positive voltage source.
1.7 Enclosure Specications
TheXT30/XT50panelshipsstandardina340enclosurewithEOLresistors,batteryleads,user’sguide,and
programming sheet.
Enclosure Model Size Color Construction (Cold Rolled Steel)
340 12.5”Wx9.5”Hx2.75”D Gray(G) 20-Gauge
349 12.5”Wx11.5”Hx3.5”D Gray(G) 20-Gauge
349A 13.25”Wx11.65”Hx3.6”D Gray(G) 18-Gaugewith16-Gaugedoor
341 13”Wx6.55”Hx3.5”D Gray(G) 20-Gauge

Digital Monitoring Products XT30/XT50 Installation Guide
2
IntroductIon
Introduction
2.1 System Congurations
The panel can be programmed to operate as any of the following system types:
• All/Perimetersystemthatprovidesoneperimeterareaandoneinteriorarea
• Home/Sleep/Awaysystemthatprovidesoneperimeter,oneinterior,andonebedroomarea.The
bedroom area provides for any protection devices the user wants disarmed during their sleeping hours
and armed in the Away mode.
• Sixareasystemthatprovidesareasofprotectionthatcanbeindependentlyarmedordisarmed.
2.2 Caution Notes
Throughoutthisguideyouwillseecautionnotescontaininginformationyouneedtoknowwheninstalling
thepanel.Thesecautionsareindicatedwithayieldsign.Wheneveryouseeacautionnote,makesureyou
completely read and understand its information. Failing to follow the caution note can cause damage to the
equipment or improper operation of one or more components in the system. See the example shown below.
Always ground the panel before applying power to any devices: The panel must be properly grounded
before connecting any devices or applying power to the panel. Proper grounding protects against
ElectrostaticDischarge(ESD)thatcandamagesystemcomponents.
Remove All Power From the Panel! Remove all AC and Battery power from the panel before installing or
connecting any modules, cards, or wires to the panel.
2.3 Compliance Instructions
ForapplicationsthatmustconformtoalocalauthoritiesinstallationstandardoraNationalRecognizedTesting
Laboratorycerticatedsystem,pleaseseetheListedComplianceSpecicationssectionneartheendofthis
guide for additional instructions.
System Components
3.1 Wiring Diagram
The system wiring diagram in Figure 1 shows some of the accessory devices for use in various applications. A
description of each module follows.
3.2 Lightning Protection
MetalOxideVaristorsandTransientVoltageSuppressorshelpprotectagainstvoltagesurgesoninputand
output circuits. This transient protection provides additional resistance to electrical surges such as lighting.
AdditionalsurgeprotectionisavailablebyinstallingtheDMP370or370RJLightningSuppressors.

XT30/XT50 Installation Guide Digital Monitoring Products
3
system components
3.3 Accessory Devices
Cellular Communicator Cards
263GDigitalCellular
Communicator Card AllowsyoutoconnecttheXT30/XT50SeriestoanycompatibleGPRS/SMSnetworkanduse its communication in place of standard dial out lines.
263CCDMACellularCommunicator
Card AllowsyoutoconnecttheXT30/XT50SeriestoanycompatibleCDMA/SMSnetwork.
263HHSPA+Cellular
Communicator Card AllowsyoutoconnecttheXT30/XT50SeriestoanycompatibleHSPA+/SMSnetwork. The263HiscompatiblewithXT30andXT50Seriescontrolpanels,version112orhigher
Zone and Output Expansion Modules
710BusSplitter/Repeater Increaseskeypadwiringdistanceto2500feet.
711SinglePointZoneExpander ProvidesoneClassBzoneforburglarydevicesandnon-poweredredevices.
714,714-8,714-16ZoneExpander ProvidesClassBzonesforburglaryandnon-poweredredevices.
712-8ZoneExpander Provides8zonesforburglarydevices.
715,715-8,715-16Zone
Expander
Provides12VDCClassBpoweredzonesforsmokedetectors,glassbreakdetectors,and
other2-or4-wiredevices.
860RelayOutputModule Providesonerelayandthreerelaysocketsforexpansionofuptofourrelays.
Interface Module
734WiegandInterfaceModule Provides arming, disarming, and codeless entry using access control readers.
738ZZ-WaveInterfaceModule ProvidesconnectionforZ-Wavemodules.
DMP Two-Way Wireless Devices
1100D/1100DH/1100DI Receiver Supportstransmittersinresidentialorcommercialwirelessoperationonthekeypadbus.
1100R Repeater Provides additional range for wireless devices.
1101UniversalTransmitter Provides both internal and external contacts that may be used at the same time to yield two
individualreportingzonesfromonewirelesstransmitter.
1102UniversalTransmitter Provides one external contact.
1103UniversalTransmitter Provides both and internal and external contacts that may be used at the same time to
yieldtwoindividualreportingzonesfromonewirelesstransmitter.RequiresEOLresistorfor
external contact.
1105UniversalTransmitter Provides both internal and external contacts that may be used at the same time to yield two
individualreportingzonesfromonewirelesstransmitter.
*1107MicroWindowTransmitter Provides a window transmitter and magnet
*1114Four-ZoneExpander ProvidesfourwirelesszoneswithEOLresisters.
*1116RelayOutput Provides one Form C relay.
*1117LEDAnnunciator Provides a visual system status indicator.
*1119DoorSounder Provides a battery operated sounder
*1121PIRMotionDetector Provides motion detection with pet immunity.
1125PIRMotionDetector
Providesmultiplelenscongurations,dualcoverageareaselection,andsensitivity
adjustments.
*1126C/*1126RPIRMotion
Detector Ceiling mount motion detector with panel programmable sensitivity and Disarm/Disable functionality.
1127C/1127WPIRMotion
Detector WallmountmotiondetectorwithpanelprogrammablesensitivityandDisarm/Disable functionality.
*1129GlassbreakDetector Detects the shattering of framed glass mounted in an outside wall and provides full-pattern
coverage and false-alarm immunity.
*1131RecessedContact
Provides concealed protection for doors, windows or other applications.
1135/*1135DBSirens Provides a wireless siren
*1139BillTrap Providesasilentalarmoptionforretailandbankingcashdrawers.
1142BCTwo-buttonPanicBelt
Clip Transmitter Provides portable two-button panic operation.
1142Two-buttonPanicTransmitter Provides permanently mounted under-the-counter two-button panic operation.

Digital Monitoring Products XT30/XT50 Installation Guide
4
system components
*1145-4(Four-Button)
*1145-2(Two-Button)
*1145-1(One-Button)
KeyFobtransmittersdesignedtoclipontoakeyringorlanyard.
1161ResidentialSmokeDetector Residentialsmokedetectorwithsounder.
1162ResidentialSmokeDetector Residentialsmoke/heatdetectorwithsounderandxedrate-of-riseheatdetector
1183-135FHeatDetector Fixed temperature heat detector
1183-135RHeatDetector Fixed temperature and rate-of-rise heat detector
1184CarbonMonoxideDetector CarbonMonoxideDetector.
Keypads
*ePAD™MobileKeypad
Allows users to control the security system from any computer using the Internet.
LCDkeypads Allowsyoutocontrolthepanelfromvariousremotelocations.Connectuptoeightkeypads.
Model7060,7063,7070,7073,7160,7163,7170,7173Thinline™keypads,7060A,7063A,
7070A,7073AAqualite™keypads,7360,7363ThinlineIcon Serieskeypads,7760ClearTouch™
keypad,7872and7873GraphicTouchscreenkeypadstothekeypadbususingterminals7,8,
9,and10.
9000SeriesLCDkeypads Allowsyoutocontrolthepanelfromvariousremotelocations.Connectuptofourkeypads.
9060,9063WirelessKeypads.
* These devices have not been investigated and shall not be used in listed installations

XT30/XT50 Installation Guide Digital Monitoring Products
5
InstallatIon
3.4 XT30/XT50 Wiring Diagram
16 to 18
gauge wire
Maximum AC
Wire distance –
16 gauge wire: 70 feet
18 gauge wire: 40 feet
RED
BLACK
Earth Ground
ss
s
s
USE MARKING
Commercial Central Station; Household Fire and
Burglar Warning System Control Unit (DACT,
PSDN: IP or Cellular)
NFPA 72
This equipment should be installed in accordance with Chapter 11
of the National Fire Alarm Code, ANSI/NFPA 72-2002, (National
Fire Protection Association, Batterymarch Park, Quincy, MA
02269). Printed information describing proper installation,
operation, testing, maintenance, evacuation planning, and repair
service is to be provided with this equipment. Warning: Owner’s
instruction notice, not to be removed by anyone except occupant.
HOUSEHOLD FIRE WIRING
Recognized limited energy cable must be
used for connection of all initiating,
indicating, and supplementary devices.
POWER LIMITED
All circui
ts on the Model XT30/XT50 comply
with the requirements for inherent power
limitation and are Class 2.
TYPES OF SERVICE
Suitable for DACT Central Station.
Suitable for Household Fire and
Household Burglary. Test weekly.
SIA CP-01-2010 minimum system is
XT30 or XT50, local Bell, and off
premise DACT communication to an
SCS-1R receiver plus ANSI/SIA
CP-01-2010 classified compatible DMP
keypads as indicated in the installation
guide.
J3
Phone Line Outputs
J11
1
2
3
4
J1
Ethernet
J16
Reset
J20
Wireless
Antenna
connection
J7 RJ
Supervision
XT30/XT50
Command Processor™ Panel
RED
PROG
J8
Programmer Header J8
Use DMP Model 330 Harness
Terminals 5-20 are Power Limited.
Listed Resistors
1.0k Ohm - DMP Model 311
3.3k Ohm - DMP Model 309
Plug into
120 VAC
60 Hz
outlet not
controlled
by switch.
Zone 10 compatibility
identifier: A
Maximum operating
range:
8.8 VDC - 14.2 VDC.
DMP Transformers
Model 321 –16.5 VAC 40 VA
Class 2 plug-in.
Model 320 –16.5 VAC 40 VA
Class 2 wire-in.
Verification
Zone
10
Control Unit
Delay
13.6 sec.
Smoke
Model
______
Detector
Delay
____sec.
Heat detectors, manual pull stations, or any
other shorting device. Unlimited number of
units.
1K Ohm EOL
on each zone 3.3K Ohm EOLSwitched Voltage
Output
Zone 10Keypad
Bus Smoke Zones 1 to 9Bell
Secondary Power Supply
1.2 Amps maximum charging current. Use only
12 VDC rechargeable batteries. Replace ev
ery 3
to 5 years.
Minimum voltage on
Auxiliary output to
process Sensor trips
is 10.4 VDC.
For Wireless Devices, Control Unit delay is 0 (zero).
Bell — 10.2 - 13.9 VDC
Total current: 1.5 Amps max.
w/ 40 VA.
AUX (RED) — Up to 500mA
auxiliary current at
10.2 VDC -
13.9
VDC from Terminal 7.
Up to 325mA auxiliary current
at 10.2 VDC - 13.9 VDC from
Termical 7 when using (2)
Model 364 1.3Ah Batteries.
Smoke Output: — 100mA at
10.2 - 13.9 VDC Terminal 11.
Smoke
Detector
1k Ohm
ss
To Keypad
or Zone
Expander
For listed applications the maximum current from a combination of bell
output, auxillary output, and smoke output is 1.6 amps.
65555
263
Module
AC Wiring must be in conduit and exit
out the left side of the enclosure.
Wiring on terminals 5 through 26
must exit right and maintain a 1/4"
separation from the AC and battery
positive wiring.
Figure 1: System Wiring Diagram

Digital Monitoring Products XT30/XT50 Installation Guide
6
InstallatIon
Installation
4.1 Mounting the Enclosure
The metal enclosure must be mounted in a secure, dry place to protect the panel from damage due to
tampering or the elements. It is not necessary to remove the PCB when installing the enclosure. The PCB
maybeinstalledinthestandard340Smallenclosure,optional341Kioskenclosure,optional349Medium
enclosure,ortheoptional349AAttackenclosure.
Whenusingcellularcommunicationoron-boardwirelesswiththe341enclosure,anSMAandwireless
antennaexitmaybeaddedatthetimeoftheinstallation.The349AAttackResistantenclosureisfactory
shippedwithoneknockoutonthetopleftoftheenclosure.Asneeded,additionalknockoutsmaybe
addedatthetimeofinstallation.SeeFigure3forthepositionsontheenclosurethatcanbeadded.Each
additionalknockoutmustbelledwithconduit.
Dual1/2"and 3/4"Conduit Knockout
Battery Shel f
Enclosure Mounting Hole s
Slide panel PCB into lower enclosure slots
Panel
PCB
screw
Model 349 Enclosure
Slide panel PCB between formed metal supports
Dual1/2"and 3/4" Conduit Knockouts
Battery Shelf
Enclosure Mounting Holes
Enclosure
Mounting
Hole
Enclosure
Mounting
Hole Panel
PCB
screw
Model 340 Enclosure
J3
Phone
Line
Outputs
J11
1 2
3 4
J1
Ethernet J16
Reset
J20
Wireless
Antenna
connection
J7 RJ
Supervision
Panel
PCB
screw
Panel
PCB
screw
Enclosure
Mounting
Hole
J3
Phone
Line
Outputs
J11
J1
Ethernet J16
Reset
J20
Wireless
Antenna
connection
J7 RJ
Supervision
1 2
3 4
J18
Load
RED
Programming
J8
J18
Load
RED
Programming
J8
65555
263
Module
65555
263
Module
Figure 2: Standard 340 Enclosure (left), Optional 349 Enclosure (right)
Figure 3: Optional 341 Enclosure (left), Optional 349A Enclosure (right)
3-Hole
Pattern for
Accessory
Modules
* 349A Optional Knockout
Front and
Rear Tamper
Switches for
350A Attack
Resistant
Enclosure
Dual 1 3/4" and 1 3/8" Conduit Knockouts
Battery Shelf
*
**
*
*
Model 349A Enclosure
Slide panel PCB between formed metal supports
J3
Phone
Line
Outputs
J11
J1
Ethernet J16
Reset
J20
Wireless
Antenna
connection
J7 RJ
Supervision
1 2
3 4
J18
Load
RED
Programming
J8
65555
263
Module
Lid Mounting Holes (4 places)
Lid Mounting Holes
(4 places)
Enclosure Mounting Holes (4 places)
PEMs for optional battery bracket
Dual 1/2" and 3/4" Conduit Knockouts
J3
Phone Line
Outputs
J11
1
2
3
4
J1
Ethernet
J16
Reset
J20
Wireless
Antenna
connection
(XT50 only)
J7 RJ
Supervision J18
Load
Programming
J8
OVC LED
Power
LED XMIT
TX RX
Wireless LEDs
RCV
Tamper Mounting Holes
(Upper and Lower)
Openings drilled
at installation
Model 341 Enclosure
65555
263
Module

XT30/XT50 Installation Guide Digital Monitoring Products
7
InstallatIon
4.2 Mounting Keypads
DMPkeypadshaveremovablecoversthatallowthebasetobemountedonawallorotheratsurfaceusing
the screw holes provided on each corner.
Formountingkeypadsonsolidwalls,orforapplicationswhereconduitisrequired,useaDMP695or696
keypadconduitbackbox.
4.3 Installation Specications
Severalfactorsdeterminetheperformancecharacteristicsofthekeypadbus:thelengthofwireused,the
numberofdevicesconnected,andthevoltageateachdevice.Whenplanningakeypadbusinstallation,
keepinmindthefollowingfourspecications:
1.DMPrecommendsusing18or22-gaugeunshielded wireforallkeypadcircuits.Do not use twisted pair
orshieldedwireforkeypadbusdatacircuits.
2.Onkeypadbuscircuits,tomaintainauxiliarypowerintegritywhenusing22-gaugewiredonotexceed
500feet.Whenusing18-gaugewiredonotexceed1,000feet.Toincreasethewirelengthortoadd
devices, install an additional power supply.
Note:Eachpanelallowsaspecicnumberofsupervisedkeypads.Addadditionalkeypadsinthe
unsupervisedmode.Refertothepanelinstallationguideforthespecicnumberofsupervisedkeypads
allowed.
3.Maximumdistanceforanyonebuscircuit(lengthofwire)is2,500feetregardlessofthewiregauge.
This distance can be in the form of one long wire run or multiple branches with all wiring totaling no
morethan2,500feet.Aswiredistancefromthepanelincreases,DCvoltageonthewiredecreases.
4.Maximumvoltagedropbetweenthepanel(orauxiliarypowersupply)andanydeviceis2.0VDC.Ifthe
voltage at any device is less than the required level, add an auxiliary power supply at the end of the
circuit.Whenvoltageistoolow,thedevicescannotoperateproperly.
Foradditionalinformationrefertothe710InstallationSheet(LT-0310)andortheLX-Bus/KeypadBusWiring
ApplicationNote(LT-2031).
Primary Power Supply
5.1 AC terminals 1 and 2
Connectthetransformerwirestoterminals1and2onthepanel.Usenomorethan70ft.of16gauge,or
40ft.of18gauge,wirebetweenthetransformerandthepaneltodeliveraminimumof15.5VACwhen
500mAofcurrentdrawisusedfromtheauxiliarypowersupplyterminal7.
Always ground the panel before applying power to any devices: The panel must be properly grounded
before connecting any devices or applying power to the panel. Proper grounding protects against
ElectrostaticDischarge(ESD)thatcandamagesystemcomponents.SeeEarthground,intheSecondary
Power Supply section.
5.2 Transformer Types
Thetransformerforthepanelis16.5VAC40VA,whichprovidesupto1.5Ampsofbelloutputcurrent,
500mAofauxiliarycurrent,and100mAofsmokedetectoroutput.UseeithertheModel320wire-inor
321plug-intransformerwiththepanel.Thetotalcurrentavailableislimitedbythetotalbatterystandby
requirements of the installation.
 Thetransformermustbeconnectedtoa120VAC60Hzcommercialpoweroutletthatisnotcontrolledbya
wall switch. Never share the transformer output with any other equipment.
5.3 Power LED
WheneitherACtransformerpowerorDCbatterypowerisconnectedtothepanelthePWRLEDshowssteady
green.

Digital Monitoring Products XT30/XT50 Installation Guide
8
InstallatIon
Secondary Power Supply
6.1 Battery Terminals 3 and 4
Connecttheblackbatteryleadtothe
negative battery terminal. The negative
terminal connects to the enclosure
groundinternallythroughtheXT30or
XT50 circuit board. Connect the red
battery lead to the positive battery
terminal.Observepolaritywhen
connecting the battery.
Add a second battery in parallel
usingtheDMPModel318DualBattery
Harness. DMP requires each battery
be separated by a PTC in the battery
harness wiring to protect each battery
from a reversal or short within the
circuit. See Figure 4.
Use sealed lead-acid batteries only: Use12VDCsealedlead-acidrechargeablebattery.Batteriessupplied
byDMPhavebeentestedtoensureproperchargingwithDMPproducts.
GEL CELL BATTERIES CANNOT BE USED WITH THE XT30/XT50 PANEL.
6.2 Earth Ground
Terminal4ofthepanelmustbeconnectedtoearthgroundusing14gaugeorlargerwiretoprovideproper
transientsuppression.DMPrecommendsconnectingtoametalcoldwaterpipeorgroundrodonly.Donot
connect to electrical conduit or a telephone company ground.
6.3 Replacement Period
DMPrecommendsreplacingthebatteryevery3to5yearsundernormaluse.
6.4 Discharge/Recharge
Thepanelbatterychargingcircuitoatchargesat13.9VDCatamaximumcurrentof1.2Ampsusinga40VA
transformer.Thetotalcurrentavailableisreducedbythecombinedauxiliarycurrentdrawfromterminals7,
11,and25.Thevariousbatteryvoltagelevelsarelistedbelow:
BatteryTrouble: Below 11.9VDC
BatteryRestored: Above 12.6VDC
6.5 Battery Supervision
The panel tests the battery once every hour when AC power is present. This test occurs 15 minutes past
eachhourandlastsforveseconds.Aloadisplacedonthebatteryandifitsvoltagefallsbelow11.9VDCa
low battery is detected. If AC power has failed, a low battery is detected any time the battery voltage falls
below11.9VDC.
If a low battery is detected with AC power present, the test is repeated every two minutes until the battery
chargesabove12.6VDC;thebatteryrestoredvoltage.Ifafaultybatteryisreplacedwithafullycharged
battery, the restored battery will not be detected until the next two-minute test is done.
6.6 XT30/XT50 Power Requirements
During AC power failure, the panel and all auxiliary devices connected draw their power from the battery.
Alldevicesmustbetakenintoconsiderationwhencalculatingthebatterystandbycapacity.Onthefollowing
pageisalistofthepowerrequirementsofthepanel.AddtheadditionalcurrentdrawofDMPkeypads,
smokedetectoroutput,andanyotherauxiliarydevicesusedinthesystemforthetotalcurrentrequired.
The total is then multiplied by the total number of standby hours required to arrive at the total Ampere-
hours required.
AC
1234
+BAC –B
318 Battery
Harness
Panel Red and
Black Battery Cables
Red
Black
Battery
Battery
Red
Black
56
BELL GND
To AC
14 AWG to
Earth Ground
XT30/XT50
Command Processor
Panel
PTC
To Bell
Circuit
Figure 4: Wiring Multiple Batteries

XT30/XT50 Installation Guide Digital Monitoring Products
9
InstallatIon
6.7 XT30/XT50 Standby Battery Calculations
Standby Battery Power Calculations Alarm Current
XT30 Panel
XT50 Panel
Built-in Network (additional current)
Built-in Cellular (additional current)
ActiveZones1-9
ActiveZone10
2-WireSmokeDetectors
Panel Bell Output
x
x
x
x
x
x
125mA
145mA
145mA
18mA
1.6mA
4mA
0.1mA
______mA
______
______
______
______
______
______
Qty ______
Qty ______
Qty ______
1500mA
x
x
x
x
125mA
145mA
145mA
18mA
*2mA
30mA
0.1mA
Max.
______mA
______
______
______
______
______
______
______
263GDigitalCellularCommunicator x 18mA ______ Qty ______ x 18mA ______
263CDigitalCellularCommunicator x 13mA ______ Qty ______ x 13mA ______
263H HSPA+ Cellular Communicator x 24mA ______ Qty ______ x 28mA ______
1100DWirelessReceiver x 40mA ______ Qty ______ x 40mA ______
1100DHWirelessHighPowerReceiver x 160mA ______ Qty ______ 160mA ______
1100DIWirelessIn-LineReceiver x 30mA ______ Qty ______ 30mA ______
860RelayOutputModule(onerelayactive)
Allfourrelaysactive x 34mA 138mA ______ ______ Qty _______ x 34mA 138mA ______ ______
7060/7160Thinline/7060AAqualiteKeypad x 72mA ______ Qty ______ x 87mA ______
7063/7163Thinline/7063AAqualiteKeypad x 85mA ______ Qty ______ x 100mA ______
7070/7170Thinline/7070AAqualiteKeypad
ActiveZones(EOLInstalled)
x 72mA
1.6mA ______ ______ Qty ______ Qty ______ 67mA 80mA ______ ______
7073/7173Thinline/7073AAqualiteKeypad
ActiveZones(EOLInstalled)
x 85mA
1.6mA ______ ______
7360ThinlineIconKeypad
7363ThinlineIconKeypad
x
x60mA 73mA ______ ______ Qty ______ Qty ______ x x67mA 80mA ______ ______
7872GraphicTouchscreenKeypad
ActiveZones(EOLInstalled)
x 145mA
1.6mA ______ ______ Qty ______ x 215mA 2.0mA ______ ______
7873GraphicTouchscreenKeypad
ActiveZones(EOLInstalled)
x 143mA
1.6mA ______ ______ Qty ______ x 243mA 2.0mA ______ ______
708 Bus Extender Module (one pair) x 20mA ______ Qty ______ x 20mA ______
710 Bus Splitter/Repeater Module x 30mA ______ Qty ______ x 30mA ______
714 Zone Expansion Modules
ActiveZones(EOLInstalled)
x
x7mA 1.6mA ______ ______ Qty ______ Qty ______ x x7mA *2mA ______ ______
712-8 Zone Expansion Module
ActiveZones(EOLInstalled)
x
x17mA 1.6mA ______ ______ Qty ______ Qty ______ x x17mA *2mA ______ ______
714-8, 714-16 Zone Expansion Module
ActiveZones(EOLInstalled)
x
x20mA 1.6mA ______ ______ Qty ______ Qty ______ x x20mA *2mA ______ ______
715 Zone Expansion Module
ActiveZones(EOLInstalled)
2-Wire Smokes
x
x
x
7mA
4mA
.1mA
______
______
______
Qty ______
Qty ______
Qty ______
x
x
x
7mA
*30mA
.1mA
______
______
______
715-8, 715-16 Zone Expansion Modules
ActiveZones(EOLInstalled)
2-Wire Smokes
x 20mA
4mA
.1mA
______
______
______
Qty ______ x 20mA
*30mA
.1mA
______
______
______
734WiegandInterfaceModule
ActiveZones(EOLInstalled)
x
x15mA 1.6mA ______ ______ Qty ______ Qty ______ x x15mA *2mA ______ ______
738A Ademco Wireless Interface Module x 75mA ______ Qty ______ x 75mA ______
738ZZ-WaveInterfaceModule x 32mA ______ Qty ______ x 47mA ______
Aux.PoweredDevicesonTerminals7and11
OtherthanKeypadsandModules
______mA ______mA
Total Standby
Total Standby______mA x number of Standby Hours
needed
Total Alarm
*Basedon10%ofactivezonesinalarmcondition.
______mA
______ =
______mA
+Total
Total Alarm
________mA-hours
________mA-hours
________mA-hours
X .001
=________Amp-hrs
______mA
Required

Digital Monitoring Products XT30/XT50 Installation Guide
10
InstallatIon
Bell Output
7.1 Terminals 5 and 6
Nominal12VDCissuppliedbyterminal5onthepaneltopoweralarmbellsorhorns.Theoutputisrated
foramaximumof1.5Ampswitha40VAtransformer.Thisoutputcanbesteady,pulsed,orTemporalCode3
dependingupontheBellActionspeciedinOutputOptionsprogramming.Terminal6isthegroundreference
forthebellcircuit.Ifusingahornorsiren,a1k0hmresistershouldbeaddedacrossthebellcircuitfor
supervision. Keypad Data Bus
8.1 Description
Terminals7,8,9,and10ofthepanelaredesignatedasthekeypaddatabus.Inadditiontokeypads,the
XT30/XT50allowstheconnectionofanycombinationofzoneexpansionmodules,GlassbreakDetectors,and
PIRstothekeypadbusuptothemaximumofeightdevices.
8.2 Terminal 7 - RED
Nominal12VDCissuppliedatterminal7topowerkeypadsandzoneexpanders.Thisisalsowherepower
foranyauxiliarydeviceissupplied.Thegroundreferenceforterminal7isterminal10.Themaximumoutput
isratedat500mA.AllauxiliarydevicestotaledtogethermustnotexceedtheTerminal7maximumcurrent
ratingof500mA.Whenthenumberofkeypadsorotherexpansiondevicesattachedexceedstheamountof
outputcurrentavailable,attachanexternalpowersupplyasdenedintheModel710InstallationSheet
(LT-0310).
8.3 Terminal 8 - YELLOW
Datareceivefromkeypadsandzoneexpanders.
8.4 Terminal 9 - GREEN
Datatransmittokeypadsandzoneexpanders.
8.5 Terminal 10 - BLACK
Terminal10isthegroundreferenceforLCDkeypads,zoneexpanders,andanyauxiliarydevicesbeing
poweredbyterminals7and11.
8.6 Keypad Bus LEDs
ThetwoLEDslocatedjustaboveterminal13indicatekeypadtransmitdata(XMIT)andkeypadreceivedata
(RCV).ThebottomLEDashesgreentoindicatedatabeingtransmittedfromthepanel.ThetopLEDashes
yellowtoindicatedatabeingreceivedbythepanelfromkeypads,zoneexpanders,etc.
8.7 Programming Connection
Alocking4-pinheader(J8)isprovidedtoconnectakeypadwhenusingaDMPModel330ProgrammingCable.
Thisprovidesaquickandeasyconnectionforprogrammingthepanel.
8.8 Keypad Addressing
KeypadBusexpansionzonesarenumberedingroupsoffourcorrespondingtotheaddress.Example:address
1iszones11-14andaddress5iszones51-54.Thereareamaximumof32zonespossibleontheKeypadBus.
Allkeypadzonesterminatewitha1k0hmEOLresister.
Address XT30/XT50
Zone Number
1 11-14
2 21-24
3 31-34
4 41-44
5 51-54
6 61-64
7 71-74
8 81-84

XT30/XT50 Installation Guide Digital Monitoring Products
11
InstallatIon
8.9 Overcurrent OVC LED
TheOvercurrentLED(OVC)lightsRedwhenthedevices
connectedtotheKeypadBusdrawmorecurrentthanthe
auxiliaryoutputrating.TheOVCLEDislocatedabove
terminals9and10asshowninFigure4.WhentheOVCLED
lightsRed,theKeypadbus/auxiliarypower(terminal7)and
theProgrammingheader(J8)shutdown.
Smoke and Glassbreak Detector Output
9.1 Terminal 11
Nominal12VDCat100mAmaximum(sharedbyterminal25)
issuppliedatterminal11topower4-wiresmokedetectorsor
other auxiliary powered devices. This output can be turned
off by the user for 5 seconds using the Sensor Reset option
intheUserMenu.Terminal10isthegroundreferencefor
terminal 11.
Burglary Zones
10.1 Description
OnXT30/XT50panels,terminals12to24arethenineburglaryzones.Forprogrammingpurposes,thezone
numbersare1to9.Thezonecongurationsonterminals12to24aredescribedbelow.
Terminal Function Terminal Function
 12 Zone1voltagesensing 19 Groundforzones5&6
 13 Groundforzones1&2 20 Zone6voltagesensing
 14 Zone2voltagesensing 21 Zone7voltagesensing
 15 Zone3voltagesensing 22 Groundforzones7,8,&9
 16 Groundforzones3&4 23 Zone8voltagesensing
 17 Zone4voltagesensing 24 Zone9voltagesensing
18 Zone 5 voltage sensing
Thevoltagesensingterminalmeasuresthevoltageacrossthe1kOhmEnd-of-Lineresistorandthezone’s
groundterminal.Drycontactsensingdevicescanbeusedinseries(normally-closed)orinparallel(normally-
open)withanyoftheburglaryprotectionzones.
10.2 Operational Parameters
Eachburglaryprotectionzonedetectsthreeconditions:open,normal,andshort.
The parameters for each are listed below:
Condition Resistance on zone Voltage on zone terminal
  Open over1300ohms over2.0VDC
 Normal 600to1300ohms 1.2to2.0VDC
  Short under600ohms under1.2VDC
J3
Phone Line
J7 RJ
Supervision
OVC LED
Power
LED
Figure 5: OVC LED location
1K Ohm
Normally
Closed
1K Ohm
Normally Open 1K Ohm
Combination Normally Open
and Normally Closed
Figure 6: Protection Zone Contact Wiring

Digital Monitoring Products XT30/XT50 Installation Guide
12
InstallatIon
10.3 Zone Response Time
Aconditionmustbepresentonazonefor500millisecondsbeforeitisdetectedbythepanel.Ensure
detectiondevicesusedontheprotectionzonesareratedforusewiththisdelay.
10.4 Keyswitch Arming Zone
YoucanuseamomentarykeyswitchonazoneprogrammedasanArmingtypeforuseinarmingand
disarming the system without a code.
Powered Zone for 2-Wire Smoke Detectors
11.1 Terminals 25 and 26
Aresettable2-wireClassBpoweredzoneisprovidedonterminals25(positive)and26(negative)ofthe
panel.Forprogrammingpurposes,thezonenumberis10ontheXT30/XT50.ThezoneusesaModel309,3.3k
OhmEOLresistor(providedwiththepanel)andhasanoperatingrangeof8.8to13.9VDC.
Thecompatibilityidentieris:B
Caution:Sensorresetonzone10dropspowertodevicesonthiszone,causingthepaneltosenseanopen
conditiononallzonetypesotherthanFire,FireVerify,andSupervisory.Whenevernon-Fireandnon-
Supervisoryzonetypesareusedonzone10,maketheappropriateadjustmentstothezone’sArmedAction
to prevent false alarms from occurring.
Manufacturer Model Detector
ID # of Detectors Zone Expansion Modules
DMP/Hochiki SLR-835B HD-6 7 715, 715-8, 715-16, 725
Sentrol/ESL 429AT, 521B, 521BXT S09A 12 715, 715-8, 715-16
System Sensor 2WTA-B, 2WTR-B A 10 715, 715-8, 715-16
Annunciator Outputs
12.1 Description
Thefourannunciatoroutputscanbeprogrammedtoindicatetheactivityofthepanel’szonesorconditions
occurring on the system. Annunciator outputs do not provide a voltage but instead switch-to-ground voltage
from another source. The outputs can respond to any of the conditions listed below:
1) Activationbyzonecondition:Steady,Pulse,Momentary,orFollower 6) Ambushalarm
2) Manuallyfromthekeypad 7) ExitandEntrytimers
3) Communicationfailure 8) SystemReady
4) Armedareaannunciation 9) LatetoClose
5) FireAlarmorFireTrouble
12.2 Harness Wiring
TheopencollectoroutputsareaccessiblebyinstallingtheDMP300Harnessonthe4-pinheaderlabeledJ11.
The output locations are shown below. For listed applications, devices connected to outputs must be located
within the same room as the panel.
Output Color Wire Output Color Wire
 1 Red 1 3 Green 3
 2 Yellow 2 4 Black 4
12.3 Model 860 Relay Module
ConnectaModel860RelayModuletothepaneltoproviderelaysfortheannunciatoroutputsthatcanbe
used for electrical isolation between the alarm panel and other systems or for switching voltage to control
variousfunctions.Themoduleincludesonerelayandprovidesthreeadditionalsocketsforexpansionofup
tofourrelays.Powerissuppliedtotherelaycoilsfromthepanelkeypadbus.The860mountsinsidethe
panelenclosureusingthe3-holemountingconguration.Plasticstandoffsareprovidedwiththemodulefor
easeofinstallation.A4-wireharnessisalsoprovidedthatconnectstheModel860tothepanel.
Relay Contact Rating: 1Ampat30VDC

XT30/XT50 Installation Guide Digital Monitoring Products
13
InstallatIon
Telephone RJ Connector
13.1 Description
ConnectthepaneltothepublictelephonenetworkbyinstallingaDMP356RJCablebetweenthepanel’sJ3
connectorandtheRJ31XorRJ38Xphonejack.CAUTION-Toreducetheriskofre,useonlyNo.26AWGor
largertelecommunicationlinecord,suchasDMPModel356SeriesPhoneCords.
AtwopinheaderlabeledRJSUP(J7)isprovidedtoallowmonitoringofthetelephonecableconnected
betweenthepanelandaRJ38Xjack(pins2and7jumpered).AttachaDMPModel306HarnessbetweenJ7
andanyavailablezone.TheJ7pinsareconnectedviathetelephonecabletotheRJ38Xjackpins2and7.
TheRJ38Xjackprovidesajumperbetweenpins2and7whichcompletesthecircuit.Programthezoneasa
Supervisorytype(SV).Whenthetelephonecableisremoved,thekeypaddisplayszonetroubleandproduces
a steady tone.
To Telephone
Line
RJ31X or RJ38X
Phone Block
8
7
6
54
3
2
1
Ring Tip
To Premise
Phone(s)
Ring 1 Tip 1
Figure 7: Phone Jack Wiring
13.2 FCC Registration
The panel complies with FCC part 68 and is registered with the FCC.
Registrationnumber:CCKAL00BXT50
RingerEquivalence:0.0B
13.3 Notication
Registered terminal equipment must not be repaired by the user. In case of trouble, the device must be
immediatelyunpluggedfromthetelephonejack.Thefactorywarrantyprovidesforrepairs.Registered
terminalequipmentmaynotbeusedonpartylinesorinconnectionwithcointelephones.Noticationmust
be given to the telephone company with the following information:
   a.Theparticularline(s)theserviceisconnectedto
b. The FCC registration number
c. The ringer equivalence
   d.Themake,model,andserialnumberofthedevice
Ethernet Connector J1
14.1 Description
TheEthernetConnector(J1)isavailableontheNetworkversionandconnectsdirectlytoanEthernet
networkusingastandardpatchcable.
14.2 Ethernet LEDs
ThetwoLEDs,locatedontheleftsideoftheJ1EthernetConnector,indicatenetworkoperation.Thetop,
LinkLEDisasteadygreenlightwhenanethernetcableisconnected.Thebottom,ActivityLEDashes
yellow to indicate messages are being received or transmitted.

Digital Monitoring Products XT30/XT50 Installation Guide
14
InstallatIon
Reset Header J16
15.1 Description
Theresetheaderislocatedjustabovetheterminalstripontherightsideofthecircuitboardandisused
toresettheXT30/XT50microprocessor.Toresetthepanelwhenrstinstallingthesystem,installthereset
jumperbeforeapplyingpowertothepanel.AfterconnectingtheACandbattery,removetheresetjumper.
To reset the panel while the system is operational, for example, prior to reprogramming, install the reset
jumperwithoutpoweringdownthesystem.Removetheresetjumperafteroneortwoseconds.
Afterresettingthepanel,beginprogrammingwithin30minutes.Ifyouwaitlongerthan30minutes,reset
the panel again.
XT30/XT50 Panel
J3
Phone Line Outputs
J11
1
2
3
4
J20
Wireless
Antenna
connection
J7 RJ
Supervision
J24 Celllular
header
Momentarily
place the Reset
jumper over both
of the J16 pins to
reset the panel.
J16
Reset
J18
Load
J1
Ethernet
OVC LED
Power
LED
TX RX
Wireless LEDs
Programming
J8
XMIT
RCV
Figure 8: Panel Showing the Reset Header

XT30/XT50 Installation Guide Digital Monitoring Products
15
InstallatIon
Flash Load Jumper J18
16.1 Description
TheXTSeriespanelsoftwarecanbeupdatedviathepanel’sprogramming(PROG)header.Toupdatethe
panel with a new software version, complete the following steps at the protected premise:
1.PlaceajumperacrosstheReset(J16)headerandthenremovetheyellowandgreenwiresfromkeypad
busterminals8and9.
2.ConnectaDMP399CablefromtheJ8ProgrammingHeadertotheserialportofyourPCoperating
RemoteLinkandcontainingtheXTRUle.RequiresRemoteLink1.43orhigher.
3.StartRemoteLinkandcreateoropentheXTSeriescontrolpanelaccountthatmatchesthepaneltobeupdated.
4.SettheConnectionInformationTypetoDirectwithabaudrateof38400andchoosetheappropriateCOMport.
5.SelectPanel>RemoteUpdate,thenselectthecorrectRUlefortheXTpanelmodel.
6.WhileplacingashortacrosstheLOAD(J18)header,removethejumperfromtheReset(J16)header.
Click<Update>inRemoteLink.
7.Afterthesoftwareversionisupdated,removetheshortfromtheLOADheader.Placethejumperacross
Reset(J16)thenremovethe399cable.
8.Replacetheyellowandgreenwirestoterminals8and9.
9.RemoveReset(J16)jumpertoresumenormalpaneloperation.
Cellular Connections
17.1 Cellular
TheJ24headerisprovidedtoconnecta263GDigitalCellularCommunicator,263CCDMACellular
Communicator,or263HHSPA+CellularCommunicator.Thecellularantennaconnectionprotrudesthrough
the top of the enclosure.
Outputs
J11
1
2
3
4
J16
Reset
J20
1100 Series
Wireless Antenna
connection
To J24 Celllular
header
Connect
antenna to
right side
only
Brass
Washer
J18
Load
1100 Series
Antenna
(XT50)
J1
Ethernet
TX RX
Wireless LEDs
Programming
J8
XMIT
RCV
65555
263 Module
Figure 9: Cellular and 1100 Series Wireless Antenna Connections