DMP Electronics XR550INT Series User manual

INSTALLATION GUIDE
XR150INT/XR550INT SERIES
INTERNATIONAL CONTROL PANEL

Digital Monitoring Products XR150INT/XR550INT Series Installation Guide
MODEL XR150INT/XR550INT SERIES PANELS
INSTALLATION GUIDE
© 2018 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.

XR150INT/XR550INT Series Installation Guide Digital Monitoring Products
i
TABLE OF CONTENTS
Product Specications Summary
1.1 Power Supply ..................................................................................................... 1
1.2 Communication................................................................................................... 1
1.3 Panel Zones........................................................................................................ 1
1.4 Keypad Bus ........................................................................................................ 1
1.5 LX500-LX900 Bus™............................................................................................. 1
1.6 Outputs.............................................................................................................. 1
1.7 EnclosureSpecications ...................................................................................... 2
Panel Features
2.1 Description......................................................................................................... 2
2.2 Zone Expansion .................................................................................................. 2
2.3 Output Expansion ............................................................................................... 2
2.4 Central Station Communication ............................................................................ 2
2.5 Caution Notes..................................................................................................... 3
2.6 Compliance Instructions ...................................................................................... 3
System Components
3.1 SpecicandNon-specicWiredInterconnections .................................................. 4
3.2 Lightning Protection ............................................................................................ 4
3.3 Accessory Devices............................................................................................... 5
Installation
4.1 Mounting the Enclosure....................................................................................... 7
4.2 Mounting Keypads and Zone Expansion Modules ................................................... 8
4.3 Connecting LX-Bus™, AX-Bus™ and Keypad Bus Devices ....................................... 9
4.4 WirelessKeypadAssociation ................................................................................ 9
5.1 AC Terminals 1 and 2 .........................................................................................10
5.2 50VA-75VA 3-Pin Header for Transformer Types ...................................................10
Secondary Power Supply
6.1 Battery Terminals 3 and 4...................................................................................10
6.2 Earth Ground (GND) ..........................................................................................10
6.3 Battery Only Restart...........................................................................................10
6.4 Battery Replacement Period................................................................................10
6.5 Discharge/Recharge ...........................................................................................10
6.6 Battery Supervision ............................................................................................11
6.7 Battery Cutoff....................................................................................................11
6.8 Power Requirements ..........................................................................................11
6.9 Standby Battery Selection...................................................................................13
Bell Output
7.1 Terminals 5 and 6 ..............................................................................................14
Keypad Bus
8.1 Description........................................................................................................14
8.2 Terminal 7 - RED................................................................................................14
8.3 Terminal8-YELLOW .........................................................................................14
8.4 Terminal 9 - GREEN ...........................................................................................14
8.5 Terminal 10 - BLACK ..........................................................................................14
8.6 Programming (PROG) Connection .......................................................................14
8.7 Keypad Bus LEDs ...............................................................................................14
8.8 OVC LED(s) .......................................................................................................14
Smoke and Glassbreak Detector Output
9.1 Terminals 11 and 12...........................................................................................15
9.2 Current Rating ...................................................................................................15

Digital Monitoring Products XR150INT/XR550INT Series Installation Guide
ii
TABLE OF CONTENTS
Protection Zones
10.1 Terminals 13–24 ................................................................................................15
10.2 Operational Parameters ......................................................................................15
10.3 Zone Response Time..........................................................................................16
10.4 Keyswitch Arming Zone ......................................................................................16
Powered Zones for 2-Wire Smoke Detectors
11.1 Terminals 25–26 and 27–28................................................................................16
Dry Contact Relay Outputs
12.1 Description........................................................................................................16
12.2 Contact Rating...................................................................................................16
12.3 Model431OutputHarnessWiring.......................................................................17
Annunciator Outputs
13.1 Description........................................................................................................17
13.2 Model300HarnessWiring ..................................................................................17
13.3 Model 860 Relay Module.....................................................................................17
Wireless Bus Expansion
14.1 Description........................................................................................................17
14.2 WirelessBusLEDs .............................................................................................17
LX-BusTM/AX-BusTM Expansion
15.1 LX-Bus HeadersLX-Bus/AX-Bus Headers...............................................................18
15.2 LX-Bus/AX-Bus LEDs ..........................................................................................18
15.3 OVC LEDs..........................................................................................................19
ETHERNET Connector (Panels with Network only)
16.1 Description........................................................................................................19
16.2 Ethernet LEDs ...................................................................................................19
16.3 Network Transient Suppression ...........................................................................19
PHONE LINE RJ Connector
17.1 Description........................................................................................................19
17.2 Phone Line Monitor ............................................................................................19
RESET and TAMPER Headers
18.1 RESET Header ...................................................................................................20
18.2 TAMPER Header.................................................................................................20
Cellular Modules
19.1 CELL MODULE Header........................................................................................21
19.2 Module Installation ............................................................................................21
19.3 Connecting the Antenna .....................................................................................21
International Certications

XR150INT/XR550INT Series Installation Guide Digital Monitoring Products
1
PANEL SPECIFICATIONS
Product Specications Summary
1.1 Power Supply
Transformer Input: Model 324INT wire-in — Primary input: 230 VAC, 50 Hz, Secondary output: 18 VAC 100
VA, 400 mA
Standby Battery: 12 VDC, 1.0 Amps Max. charging current
Models 365, 366, 368, or 369
Replace every 3 to 5 years
Auxiliary: 12 VDC output at 1.5 Amp Max
Bell Output: 12 VDC at 1.5 Amp Max
All circuits are inherent Power Limited except the red battery wire and AC terminal.
1.2 Communication
• Built-in network communication to DMP Model SCS-1R or SCS-VR Receivers (Panels with Network
only)
• Built-in Contact ID communication to DMP Model SCS-1R Receivers
• Can operate as a local panel
1.3 Panel Zones
• Eight 1k Ohm EOL/Dual EOL burglary zones (zones 1 to 8)
• Two 3.3k Ohm EOL powered zone with reset (zones 9 and 10)
1.4 Keypad Bus
You can connect up to a total of 16 of the following supervised keypads and expansion modules to keypad
bus:
• Alphanumeric keypads
• One, four, eight, and sixteen-zone expansion modules
• Wireless Keypads (maximum of 7)
1.5 LX500-LX900 Bus™
You can connect the following devices to the LX-Bus™ connections provided on the panel. See Accessory
Devices section 3.3.
• Four, eight, sixteen- and/or single-zone expansion modules
• Relay output expansion modules
• Graphic annunciator modules
1.6 Outputs
The XR150INT/XR550INT Series panels provide two Single Pole, Double Throw (SPDT) relay outputs which
require the installation of two Model 305 relays, each rated 1 Amp at 30 VDC resistive (power limited sources
only).
A Model 431 Output Harness is required to use these outputs.
The XR150INT/XR550INT Series panels also provide four open collector outputs rated for 50mA each. The
open collector outputs provide ground connection for a positive voltage source. A Model 300 Output Harness
is required to use these outputs.

Digital Monitoring Products XR150INT/XR550INT Series Installation Guide
2
PANEL SPECIFICATIONS
1.7 Enclosure Specications
The XR150INT/XR550INT Series panels are shipped in an enclosure with a transformer, End-of-Line resistors,
battery leads, user guide, and programming sheets.
Enclosure
Model
Size Color(s) Construction (Cold
Rolled Steel)
350INT 44.45 W x 34.29 H x 8.89 D cm Gray (G) or Red (R) 18-Gauge
350AINT 44.45 W x 34.29 H x 8.89 D cm Gray (G) 18-Gauge with
16-Gauge door
349INT 31.75 W x 29.21 H x 8.89 D cm Gray (G) 20-Gauge
352PINT 36.83 W x 81.28 H x 10.16 D cm Gray (G) 16-Gauge
352XINT 36.83 W x 81.28 H x 10.16 D cm Gray (G) 16-Gauge
Panel Features
2.1 Description
The DMP XR150INT/XR550INT Series system is made up of an alarm panel with a built-in communicator, an
enclosure, battery, one transformer, and keypads. Each panel is a versatile 12VDC, combined access control,
burglary, and re communicator panel with battery backup. The panels provide eight on-board burglary zones
and two on-board 12 VDC Class B powered zones. The powered zones have a reset capability to provide for 2-wire
smoke detectors, relays, or other latching devices. Combined current requirements of additional modules may
require an auxiliary power supply. Refer to the Power Requirements section in this guide when calculating power
requirements. The panels can communicate to DMP SCS-1R Receivers using digital dialer, cellular, network, or
Contact ID communication. Panels using cellular, network, or encrypted communication can also communicate to
DMP SCS-VR Receivers.
2.2 Zone Expansion
Each panel provides multiple options for zone expansion:
• 10 on-board zones
• Up to 64 programmable keypad zones
• Up to 500 LX-Bus zones
Using DMP LCD keypad remote zone capability and zone expansion modules, additional zones are available on each
panel:
• XR550INT provides up to 574 additional zones
• XR150INT provides up to 142 additional zones
The panel keypad data bus supports up to 16 supervised device addresses with each address supporting up to four
programmable expansion zones (64 total).
Using the on board LX-Bus™ connections, and any combination of single, four, eight, or sixteen-zone expansion
modules and single-zone LX-Bus™ detectors, additional zones are available on each panel:
• XR550INT provides up to 500 additional zones (LX500-LX900)
• XR150INT provides up to 100 additional zones (LX500)
Note: Do not use shielded or twisted pair wiring for LX-Bus or Keypad Bus circuits.
2.3 Output Expansion
In addition to the two SPDT relays and four programmable open collector outputs on the XR150INT/XR550INT
Series panels, you can also connect up to 25 programmable Model 716 Output Expansion Modules to each LX-Bus.
These modules can provide an additional 500 or 100 programmable SPDT relays.
The panels provide Output Schedules for programming the 716 to perform a variety of annunciation and control
functions. Also assign the 716 outputs to any panel Output Options such as Fire Alarm, Communication Fail, or
Phone Trouble Outputs. Refer to the 716 Installation Guide (LT-0183).
2.4 Central Station Communication
You can program the panel for reporting to DMP SCS-VR or SCS-1R Receivers using digital dialer, cellular, network,
or Contact ID communication. The panels connect at the premises to a standard RJ31X or RJ38X telephone jack.

XR150INT/XR550INT Series Installation Guide Digital Monitoring Products
3
PANEL SPECIFICATIONS
2.5 Caution Notes
Throughout this guide you will see caution notes containing information you need to know when installing the
panel. These cautions are indicated with a yield sign. Whenever you see a caution note, make sure you completely
read and understand its information. Failing to follow the caution note can cause damage to the equipment or
improper operation of one or more components in the system. See the example shown below.
Always ground the panel before applying power to any devices: The panel must be properly grounded
before connecting any devices or applying power to the panel. Proper grounding protects against Electrostatic
Discharge (ESD) that can damage system components.
2.6 Compliance Instructions
For applications that must conform to a local authorities installation standard or a National Recognized Testing
Laboratory certicated system, please see the Compliance Listing Guide LT-1330INT for additional instructions.

Digital Monitoring Products XR150INT/XR550INT Series Installation Guide
4
SYSTEM COMPONENTS
System Components
3.1 Specic and Non-specic Wired Interconnections
The XR150INT/XR550INT Series panels diagram below shows some of the accessory modules you can connect
for use in various applications. A brief description of each module follows in section 3.3.
AC
1 2 3 4 5 6 7 8 10 11 12 13 14 15 16 17 18 199 20 21 22 23 24 25 26 27 28
+B BELL GND SMK GNDRED YEL GRN BLK Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9+ Z9– Z10+ Z10–AC –B GND GND GNDGND
Auxiliary Power
Total current combined from terminals
7, 11, 25, 27, XBUS and LX500-LX900
1.5 Amp Max 13.8 VDC to 10.2 VDC
LX800 LX900
J4
Tamper
K6 K7
Output 1 Output 2
J3
Phone Line
Battery
Start
J8
J16
Reset
Out1 Out2
Outputs 3-6
J11
3
4
5
6
J2
OVC
XR550INT Series
International Panel
LX500 LX700
XBUS
J13
J14 J9 J15 J19J17
J24
Form C Relays (J2)
Output Color Code–Model 431 Harness
Output 2 N/O Orange/White
Output 2 Com White/Gray
Output 2 N/C Violet/White
Output 1 N/O Orange
Output 1 Com Gray
Output 1 N/C Violet
Annunciator Outputs (J11)
Output Color Code
Output 3 Red
Output 4 Yellow
Output 5 Green
Output 6 Black
ss
J12 75VA
50VA
Listed Resistors
1.0k Ohm - DMP Model 311
3.3k Ohm - DMP Model 309
10K Ohm - DMP Model 308
LX600
Tamper
16 to 18 gauge wire
Maximum AC Wire distance
with 16 gauge wire: 70 feet
with 18 gauge wire: 40 feet
RED
BLACK
Cold Water
Pipe Earth
Ground
Bell
3.3k Ohm
Resistor DMP
Model 309
3.3k Ohm
Resistor DMP
Model 309
s
= Supervised Circuit
Zone
9
Zone
10
22 gauge minimum 22 gauge minimum 22 gauge minimum 22 gauge minimum
RED
YELLOW
GREEN
BLACK
Zone Expander
Models 714-8INT,
714-16INT
20mA @ 12 VDC
RED
YELLOW
GREEN
BLACK
s
Dual
1k
Ohm
Zone Expander
(up to 8 zones)
Model 712-8INT
19mA @ 12 VDC
1k
Ohm
Earth Ground
s s s s
sss
s
s
s
s
s
s
¼"
AC Wiring must be in conduit and exit
out the left side of the enclosure.
Wiring on terminals 5 through 22 must
exit right and maintain 1/4" separation
from the AC and battery positive wiring.
Dual
1k
Ohm
Dual
1k
Ohm
Dual
1k
Ohm
Dual
1k
Ohm
Dual
1k
Ohm
Dual
1k
Ohm
Dual
1k
Ohm
ssssssss
ssssssss
Dual
1k
Ohm
ss
Dual
1k
Ohm
ss
Dual
1k
Ohm
ss
Dual
1k
Ohm
ss
s
Model 324INT 230V 100VA
18 VAC, 50 Hz,
400 mA
CAUTION: DO NOT USE LOOPED WIRE
UNDER TERMINALS. BREAK WIRE RUN TO
PROVIDE SUPERVISION OF CONNECTIONS.
WARNING: Incorrect
connections may cause
damage to the unit.
Bell cutoff time
range is 2 to 15
minutes, non-coded.
Bell
12 VDC
Default cutoff time 15 min.
Minimum cutoff time 2 min.
1.5 Amp Max
Conduit
INPUT OUTPUT
GROUND
Figure 1: XR550INT Series Wiring Diagram
3.2 Lightning Protection
Metal Oxide Varistors and Transient Voltage Suppressors help protect against voltage surges on panel input and
output circuits. Additional surge protection is available by installing the Model 270 Network Transient Suppression
Module.

XR150INT/XR550INT Series Installation Guide Digital Monitoring Products
5
SYSTEM COMPONENTS
3.3 Accessory Devices
Cellular Communicator Cards
263HINT HSPA+ Cellular
Communicator
Allows you to connect the XR150INT/XR550INT Series panels to any compatible HSPA/SMS
network.
Accessory Modules
270 Network Transient
Suppression Module
Provides transient surge protection for the ETHERNET Connector.
Expansion Modules
710 Bus Splitter/Repeater Allows you to increase keypad or LX-Bus™ wiring distance to 2500 feet.
714-8INT, 714-16INT Zone
Expanders
Provides Class B zones for connecting burglary and non-powered re devices.
712-8INT Zone Expander Provides Class B zones for connecting burglary devices.
716 Output Expander Provides four Form C relays (SPDT) and four switched grounds (open collector) for use in a
variety of remote annunciation and control applications for use on the LX-Bus only.
7 34INT, 734NINT Wiegand Interface
Modules
Provides system codeless entry, and arming and disarming using access control readers.
DMP Two-Way Wireless Devices
1100XINT Receiver Supports up to 500/100 devices in residential or commercial wireless operation.
1100RINT Repeater Provides additional range for wireless devices.
1101INT Universal Transmitter Provides both internal and external contacts that may be used at the same time to yield
two individual reporting zones from one wireless transmitter.
1103INT Universal Transmitter Provides both internal and external contacts that may be used at the same time to yield
two individual reporting zones from one wireless transmitter. Requires EOL resistor for
external contact. Provides Disarm/Disable functionality.
1106INT Universal Transmitter Provides both internal and external contacts that may be used at the same time to yield
two individual reporting zones from one wireless transmitter.
1107INT Micro Window Transmitter Provides a wireless window transmitter.
1114INT Four-Zone Expander Provides four wireless zones.
1116INT Relay Output Provides one Form C relay.
1117INT LED Annunciator Provides a visual system status indicator.
1118INT Remote Indicator Light Provides a visual indication of a Panic situation.
1121INT PIR Motion Detector Provides motion detection with pet immunity.
1126RINT PIR Motion Detector Ceiling mount motion detector with panel programmable sensitivity and Disarm/Disable
functionality.
1127CINT/1127WINT PIR Motion
Detector
Wall mount motion detector with panel programmable sensitivity and Disarm/Disable
functionality.
1129INT Glassbreak Detector Detects the shattering of framed glass mounted in an outside wall and provides full-pattern
coverage and false-alarm immunity.
1131INT Recessed Contact Provides a recessed contact option for door or window applications.
1135INT Wireless Siren Provides a wireless siren.
1139INT Bill Trap Provides a silent alarm option for retail and banking cash drawers.
1141WINT Wireless Wall Button Provides a water-resistant one-button wireless transmitter.

Digital Monitoring Products XR150INT/XR550INT Series Installation Guide
6
SYSTEM COMPONENTS
DMP Two-Way Wireless Devices (continued)
1142BCINT Two-button Hold-up
Belt Clip Transmitter
Provides two-button hold-up operation with a belt clip.
1142INT Two-button Hold-up
Transmitter
Provides permanently mounted under-the-counter two-button hold-up operation.
1144-4INT (Four-Button)
1144-2INT (Two-Button)
1144-1INT (One-Button)
Key Fob transmitters designed to clip onto a key ring or lanyard.
1166 Wireless Smoke Ring Installs on any traditional AC-powered, three wire, interconnected smoke alarm system.
1183-135F Heat Detector Fixed temperature heat detector.
1183-135R Heat Detector Fixed temperature and rate-of-rise heat detector.
1184 Carbon Monoxide Detector Carbon monoxide detector.
Interface Modules
738Z+ Z-Wave Interface Module Provides connection for Z-Wave modules.
Indicating and Initiating Devices
860INT Relay Module Provides dry relay contacts that are programmable and controlled from the DMP panel
annunciator outputs. Includes one Form C (SPDT) relay rated 1 Amp @ 30VDC. Sockets are
provided to allow the addition of three Model 305 plug-in relays. These relays can be used
for electrical isolation between the alarm panel and another system or switching 5, 12, or
24 Volts to control various functions within a building or around its perimeter.
Keypads
LCD keypads Allows you to control the panel from various remote locations. Connect up to sixteen Model
7060-WINT, 7063-WINT, 7073-WINT, Thinline™ keypads, or the 7872-WINT and 7873-WINT
Graphic Touchscreen keypads to the keypad bus using terminals 7, 8, 9, and 10.
Wireless keypads Allows you to control the panel from various remote locations. Connect up to seven
9060-WINT/9063-WINT Wireless Keypads or 9862-WINT/9863-WINT Wireless Graphics
Keypads.