DMP Electronics Thinline Aqualite 7000 Series Installation guide

FRI 2: 52 PM
1 2 3 4
5 6 7 8
9 0 CMD
A
C
B
D
F
E
G
I
H
J
L
K
V
X
W
S
U
T
P
R
Q
M
O
N
Y
Z
E
N
T
E
R
B
A
C
K
INSTALLATION AND PROGRAMMING GUIDE
7000 Series ThinlineTM and
AqualiteTM Keypad

TABLE OF CONTENTS
About the Keypad .........................1
Keypad Features........................... 2
Enter Characters........................... 4
Number Pad .......................................................... 4
Panic Key Options .............................................. 5
User Options Menu............................................. 6
Install the Keypad......................... 7
Remove the Cover.............................................. 7
Wire the Keypad.................................................. 8
Wire for Access Control ................................... 11
Wire the Electronic Lock ................................13
Wire the 333 Suppressor .................................13
Program the Keypad ................... 16
Keypad Options...................................................16
Custom Card Format.................. 20
Additional Programming................................. 27
Test the Keypad ...........................28
End User Training ....................... 30
Keypad Arming and Disarming .....................31
Keypad Access Control ................................... 33
Keypad Entry Delay .......................................... 34
Wiring Specifications..................35
Keypad Specifications ............... 36
Public Card Formats ...................37
Readers and Credentials ............38
Compliance Specifications ....... 40
Accessories.................................. 40
Certifications................................ 41
FCC Information ......................... 42
Industry Canada Information.... 43

7000 Series Installation and Programming Guide | Digital Monitoring Products, Inc. 1
ABOUT THE KEYPAD
Thinline Series (7060, 7063, 7070, 7073, 7160, 7163, 7170, and 7173) and Aqualite Series
(7060A, 7063A, 7070A, and 7073A) LCD keypads oer flexible features and functionality.
Each keypad provides:
• Custom 16-character home or business name in the display
• Four 2-button panic keys
• AC Power/Armed LED
• 32-character display
• Backlit keyboard and DMP logo
• Internal speaker
• Red keyboard lighting in alarm conditions
• Simple harness connection to 4-wire keypad bus
• Optional backboxes for conduit or wall mount applications
Models 7070/A, 7073/A, 7170, and 7173
Provide four fully-programmable, Class B, Style A, supervised, power limited protection
zones that can be programmed for a variety of burglary and access control applications.
Models 7063/A, 7073/A, 7163, and 7173
Provide a built-in proximity card reader designed to read proximity credentials.
Models 7073/A and 7173
Provide a door strike relay and allow Wiegand input from external card readers.

Digital Monitoring Products, Inc | 7000 Series Installation and Programming Guide2
KEYPAD FEATURES
FRI 2: 52 PM
1 2 3 4
5 6 7 8
9 0 CMD
A
C
B
D
F
E
G
I
H
J
L
K
V
X
W
S
U
T
P
R
Q
M
O
N
Y
Z
E
N
T
E
R
B
A
C
K
Armed/Power
LEDs
Proximity
Credential Reader
and Backlit Logo
Keypad Display/
Status List
Select Keys
Panic Keys
Command
(CMD) Key
Back Arrow Key
1 43
2
Figure 1: 7000 Series LCD Keypad

7000 Series Installation and Programming Guide | Digital Monitoring Products, Inc. 3
ABC SECURITY
FRI 2: 52 PM
1 2 3 4
5 6 7 8
Power LED
Armed LED
32-Character Display
Select Keys
Command
Back Arrow
9 0 CMD
A
C
B
D
F
E
G
I
H
J
L
K
V
X
W
S
U
T
P
R
Q
M
O
N
Y
Z
E
N
T
E
R
B
A
C
K
Proximity
Credential
Reader and
Backlit Logo
Figure 2: Thinline 7100 Series LCD Keypad

Digital Monitoring Products, Inc | 7000 Series Installation and Programming Guide4
ENTER CHARACTERS
NUMBER PAD
1. Choose a character from the table. Use the Greek Characters table if Greek was
selected as the keypad language setting.
2. Identify the Number the character correlates with and press that number on the
number pad.
3. Identify the Select Key for the character and press that select key on the keypad.
Press that select key again for the lowercase letter (Latin characters only).
4. When the desired character displays on the keypad, return to step 1 to enter
another character or press CMD if finished.
NUMBER SELECT KEY
12 3 4
1A B C ( [ {
2D E F ) ] }
3G H I ! ^ ~
4J K L ? “ |
5M N O / \ `
6P Q R & $
7S T U @ %
8V W X , =
9Y Z Space : _ ;
0- + . ‘ * < # >
Table 1: Latin Characters
NUMBER SELECT KEY
12 3 4
1Α Β Γ ( [ {
2Δ Ε Ζ ) ] }
3Η Θ Ι ! ^ ~
4Κ Λ Μ ? “ |
5Ν Ξ Ο / \ `
6Π Ρ Σ & $
7Τ Υ Φ @ %
8Χ Ψ Ω , =
9Space Space Space : _ ;
0- + . ‘ * < # >
Table 2: Greek Characters

7000 Series Installation and Programming Guide | Digital Monitoring Products, Inc. 5
PANIC KEY OPTIONS
2-Button Panic Keys
All keypads oer a panic key function that allows users to send panic, emergency, or fire
reports to the central station in an emergency. Enable the panic key function in the keypad
user menu. Place the supplied icon stickers below the top row select keys. The user must
press and hold the two select keys for two seconds until a beep is heard.
Panic (left two select keys)—Zone 19 + Device Address
Emergency Non-Medical (center two select keys)—Zone 29 + Device Address
Fire (right two select keys)—Zone 39 + Device Address
7/0 Panic Keys
All keypads allow the user to initiate a panic alarm by pressing the 7 and 0 (zero) keys at
the same time for one-half (1/2) second. Enable the 7/0 Panic function in Installer Options.
When enabled, all keypads send a Zone Short message to the panel for the first zone of
the keypad address. When the keys are released, a Zone Restore message can be sent
from the initiating keypad. To produce a panic alarm, program the first zone of the keypad
address as a panic type (PN) in panel programming. Place a 1k Ohm end-of-line (EOL)
resistor, DMP Model 311, across the white/brown pair of zone wires on models 7070/A,
7073/A, 7170, and 7173. A Zone Restore message sends when the keys are released. The 1k
Ohm EOL resistor is not required on 7060/A, 7063/A, 7160, and 7163 keypads.

Digital Monitoring Products, Inc | 7000 Series Installation and Programming Guide6
USER OPTIONS MENU
To access the Options menu, press and hold the back arrow and CMD keys for 2 seconds.
Backlighting Brightness
Adjust the LCD display brightness level, power and armed LEDs, the green keyboard,
and the logo backlighting. At SET BRIGHTNESS, use the left select key to decrease the
brightness and the right select key to increase the brightness. If the brightness level is
lowered, it reverts to maximum intensity whenever a key is pressed. If no keys are pressed,
and the speaker has not sounded for 30 seconds, the user-selected brightness level
restores.
Internal Speaker Tone
Adjust the keypad internal speaker tone. At SET TONE, use the left select key to decrease
the tone and the right select key to increase the tone.
Internal Volume Level
Adjust the keypad internal speaker volume for key presses and entry delay tone
conditions. During alarm and trouble conditions, the volume is always at maximum level.
At SET VOLUME LEVEL, use the left select key to decrease the volume and the right select
key to increase the volume.
Model Number
Display the keypad model number, firmware version, and date.
Keypad Address
Display the current keypad address.

7000 Series Installation and Programming Guide | Digital Monitoring Products, Inc. 7
INSTALL THE KEYPAD
REMOVE THE COVER
The keypad housing is made up of two parts: the cover,
which contains the circuit board and components, and
the base.
To separate the keypad cover from the base, insert a
flathead screwdriver into one of the slots on the bottom
of the keypad and gently lift the screwdriver upward.
Repeat with the other slot. Gently separate the cover
from the base and set the cover containing the keypad
components aside. See Figure 3.
1
Figure 3: Separate the
Keypad Housing
Cover
Base

Digital Monitoring Products, Inc | 7000 Series Installation and Programming Guide8
WIRE THE KEYPAD
Each keypad model has specific wiring assignments. All zones are supervised. Use
1kOhm EOL resistors, DMP Model 311 on keypad zones 1-4. Locate the keypad model
below and refer to Figure 5 to wire the keypad.
Models 7060/A, 7063/A, 7160, and 7163
Supplied with a 4-wire harness for panel keypad bus connection.
Models 7070/A, 7073/A, 7170, and 7173
Supplied with a 12-wire data bus/zone harness. Four wires connect to the keypad bus.
The remaining eight wires are for the four zone inputs, four wires for each zone.
Models 7073/A and 7173
Supplied with a 5-wire output/reader harness and a 12-wire data bus/zone harness.
Firmly grasp the wires near the base and hold the outside
edges of the keypad housing. Line up the red and yellow
wires with the guides on the board to inset the connector
into the J5 keypad terminal. Observe wire colors when
connecting the red, yellow, green, and black wires to the
keypad bus. See Figure 4.
• Connect red wire to panel terminal 7
• Connect yellow wire to panel terminal 8
• Connect green wire to panel terminal 9
• Connect black wire to panel terminal 10
2
Figure 4: Wiring Harness
J5
Y/W
R

7000 Series Installation and Programming Guide | Digital Monitoring Products, Inc. 9
Additional Power Supply
If the current draw for all keypads exceeds the panel output, provide additional current by
adding a Model 505-12 auxiliary power supply.
1. Connect all keypad black ground wires to the power supply negative terminal.
2. Run a jumper wire from the power supply negative terminal to the panel common
ground terminal.
3. Connect all keypad power (+12VDC) wires to the power supply positive terminal.
Do not connect the power supply positive terminal to any panel terminal. Refer to
the 505-12 Power Supply Installation Guide if needed (LT-0453).
Keypad Bus Monitor
For listed fire protective systems, the 893A Module or 277 Trouble Sounder must be
installed on the XR150/XR550 Series panel to monitor the keypad bus. It should be
programmed to sound when the keypad bus fails to operate.

Digital Monitoring Products, Inc | 7000 Series Installation and Programming Guide10
1K EOL
1K EOL
1K EOL
1K EOL
Green/White – Connect Reader Data 0
White – Connect Reader Data 1
Orange – Door Strike N/O
Gray – Door Strike C
Violet – Door Strike N/C
Yellow/White
White/Yellow
Orange White
White/Orange
Red/White
White/Red
Brown/White
White/Brown
Black – Ground
Green – Receive Data
Yellow – Send Data
Red – Keypad Power
– Zone 4
– Zone 3
– Zone 2
– Zone 1
ExternalReader/Door Strike
7073/7073A, 7173 Keypads
All Keypads
Zones 1-4
7070/7070A, 7073/7073A, 7170/7173 Keypads
Surface and Backbox
Mounting Holes
Combined 4-square
and 3-gang switch box
Mounting Holes
Surface and Backbox
Mounting Holes
*All zones are supervised and suitable for fire applications.
*Maximum zone line impedence is 100 Ohms.
*Ground fault detected at 1420 Ohms or less.
Figure 5: Keypad Back Showing Wiring
Harness Assignments

7000 Series Installation and Programming Guide | Digital Monitoring Products, Inc. 11
3WIRE FOR ACCESS CONTROL
Internal Access Control Reader
The 7063/A, 7073/A, 7163, and 7173 keypads provide a built-in proximity card reader
that is compatible with most standard 125kHz proximity credentials. An external
13.56MHz proximity reader can be connected and will be compatible with 13.56MHz
proximity credentials. For a list of publicly supported card formats, see Public Card
Formats.
Note: Some proximity credentials are not compatible with DMP proximity
keypads. Test the intended proximity credentials with the application before
installation. DMP does not guarantee compatibility with credentials not
purchased from DMP.
External Access Control Reader
To accept Wiegand data input from other external card readers, connect a 12VDC
external reader to a 7073/A or 7173 keypad. Connect the red and black power wires
from the reader to the power wires from the panel. These connect in parallel with the
keypad power wires. Connect the reader (Data 1) wire to the white wire on the 5–wire
keypad cable. Connect the reader (Data 0) wire to the green/white wire on the 5–wire
keypad cable. See Figure 6.

Digital Monitoring Products, Inc | 7000 Series Installation and Programming Guide12
Figure 6: Access Control Wiring
Green/White* - Connect Reader Data 0
White - Connect Reader Data 1
Orange - Door Strike Normally Open
Gray - Door Strike Common
Violet - Door Strike Normally Closed
Black – Ground
Green – Receive Data
Yellow – Send Data
Red – Keypad Power
– Yellow & White
Zone 4
– Orange & White
Zone 3 (REX)
– Red & White
Zone 2
– Brown & White
Zone 1 (7/0 Panic)
NC
C
NO
WHT
GRN
Z4 -
Z4 +
Z3 -
Z3 +
Z2 -
Z2 +
Z1 -
Z1 +
BLK
GRN
YEL
RED
External Card
Reader
To Panel Keypad Bus
1K EOL
s
s
1K EOL
s
s
1K EOL
s
s
1K EOL
s
s
*Only the green/white,
white, black, and red
wires connect to the
external card reader.

7000 Series Installation and Programming Guide | Digital Monitoring Products, Inc. 13
WIRE THE ELECTRONIC LOCK
The 7073/A and 7173 keypads provide one internal programmable Form C single
pole, double throw (SPDT) relay for controlling door strikes or magnetic locks. Three
wires on the 5-wire harness, violet normally closed (N/C), gray common (COM), and
orange normally open (N/O), allow you to connect devices to the relay. The Form C
relay draws up to 15mA of current and the contacts are rated for 1Amp at 30VDC
maximum.
WIRE THE 333 SUPPRESSOR
One Model 333 Suppressor is included with the 7073/A and 7173 keypads. If the
device being controlled by the relay is connected to the N/O and C wires, install the
suppressor on the N/O and C wires. If the device is connected to the N/C and C wires,
install the 333 on N/C and C wires. See Figure 7.
4
5

Digital Monitoring Products, Inc | 7000 Series Installation and Programming Guide14
Model 333
Supressor
Common
–+
Magnetic Door Lock
DMP 505
Power Supply
Normally Open
Green/White – D0
White – D1
Orange – N/O
Gray – C
Violet – N/C
N/O
C
N/C
Normally
Closed
Keypad
5-Wire Harness
Figure 7: 5-Wire Harness and 333 Suppressor Installation

7000 Series Installation and Programming Guide | Digital Monitoring Products, Inc. 15
Door Strike Relay Operation
When the user code sent from the reader is verified by the panel, the keypad door
strike relay activates for five seconds. During this time, the access door connected to
Zone 2 must be opened to start the programmed entry/exit timer and Zone Bypass if
programmed and used. The five second door strike is panel programmable when the
keypad is used on an XR150/XR550 Series panel.
Zone 2 Door Contact with Bypass
If the door being released by the 7073/A and 7173 keypad is protected, you can provide
a programmed bypass time by connecting its contact to Zone 2 (white/red pair) on the
keypad and enabling the bypass feature. Door contacts may be N/C or N/O.
Zone 3 Request to Exit
You can also connect a N/O PIR (or other motion sensing device) or a mechanical switch
to Zone 3 (white/orange pair) on the 7073/A and 7173 keypad to provide Request to Exit
(REX) capability. When Zone 3 shorts, the keypad relay activates for 5 seconds. During
this time, the user can open the protected door to start the programmed Bypass entry/
exit timer. If the door is not opened within five seconds, the relay restores to its locked
state. A Zone 3 REX is inhibited for three seconds after the keypad reads a card and a
door strike occurs. This is to allow area entry and pass under a REX PIR.

Digital Monitoring Products, Inc | 7000 Series Installation and Programming Guide16
PROGRAM THE KEYPAD
Keypad Options and Keypad Diagnostic menus allow install and service technicians to
configure and test keypad operation. To access the installer options:
1. Hold down the back arrow and CMD keys for two seconds.
2. At SET BRIGHTNESS, enter 3577 (INST) and press CMD.
The display changes to KPD OPT KPD DIAG and STOP. The Keypad Options menu allows
you to set the keypad address, select Supervised or Unsupervised mode, change the
default keypad message, selectively enable the 2-button Panic keys, Bypass, REX, and set
entry card options.
All programming options display on all keypads. However, actual operation for some
programming options is restricted to the appropriate model.
KEYPAD OPTIONS
Keypad Options
To program keypad options, press KPD OPT.
Current Keypad Address
Set the current keypad address from 01 to 08 for
XT30/XT50/XR150 Series panels or 01 to 16 for XR550Series
panels. The default address is 01. To change the current
address, press any select key and enter the new address. Do
not enter a leading zero for addresses 01 to 09.
KPD KPD
OPT DIAG STOP
CURRENT KEYPAD
ADDRESS: 1