DMP Electronics 692F Assembly instructions

InstallatIon sheet
692F Fire Command LED Keypad
Description
The 692F Fire Command LED Keypad offers 5 sets of highly visible LED annunciation of alarm and trouble conditions
on DMP XR5FC and XR5SL Commercial Fire/Communicator Panels. The 692F provides individual zone alarm and
trouble LEDs for zones one to ve. Also, system LEDs, an internal sounder, 2-button Fire alarm initiation, and
Silence, Reset, and Fire Drill functions are provided. The 692F operates on 8.0 to 16 VDC at 30mA in normal mode
and can draw up to 70mA in alarm.
Removing the Keypad Base
The 692F is made up two parts: the front, containing the circuit board and other components, and the base. To
remove the base, insert a at screwdriver into one of the openings on the bottom and carefully twist it while gently
lifting the keypad from the base. Repeat with the other opening, then lift the keypad from the base.
Inserting the Reference Card
A reference card has been supplied with the 692F
keypad. The reference card is provided to assist the users
when operating their security systems. Write the zone
descriptions on the front of the card. Slide the card in the
back of the base before installing the keypad. Refer to
Figure 1 for reference card installation.
Installing the Keypad
The 692F has been designed to easily install on any
4-square box, 3-gang switch box, 695 and 696 backbox,
or on any at surface. Figure 1 shows the mounting hole
locations on the keypad base.
Wiring the Keypad
The 692F keypad is supplied with a single 4-wire harness
for connection to the XR5FC to XR5SL panel’s keypad data
bus wiring. Connect the 4-wire harness to the back of the
PCB as shown. Then connect the wires to the panel terminals 7, 8, 9, and 10.
Buzzer Operation
Each time a user presses a key on the 692F, the buzzer emits a short tone. After the user performs a successful
keypad operation, the buzzer emits a 1/2 second tone. If the operation is not successful, the buzzer emits four short
tones. This alerts the user to perform the function again. During trouble conditions, the keypad emits a steady tone
to alert the user. Entering the user code silences the buzzer.
Keyboard Backlighting
The keyboard on the 692F lights anytime a key is pressed or the alert buzzer sounds making it easy for users in
darkened rooms to enter their code or perform a command.
984 COMMAND
Enter 984 + COMMAND to allow the panel to pick up the phone line when a Remote Link™ computer is calling
the panel. If the panel was previously programmed to answer calls from Remote Link™, the panel will answer
automatically.
Enter 984 + COMMAND plus up to a 15-digit phone number to contact a Remote Link™ computer from the panel.
Zone Alarm and Trouble LEDs
The 692F contains ve red zone alarm LEDs and ve yellow zone trouble LEDs. The red alarm LEDs turn on
steady during an alarm condition and turn off when the zone has restored to normal and a Sensor Reset has been
performed. If the zone alarm or trouble is a Supervisory type zone, the LED pulses (1 second on, 1 second off).
The yellow trouble LEDs turn on during a trouble condition, turn off when the zone restores to normal, and wink
(1/4 second on, 1 3/4 second off) when the zone has been bypassed.
Three System LEDs
The 692F has three system LEDs. The system LEDs are located near the top left corner of the keypad.
Yellow Silenced LED turns on when the bells are silenced manually from the keypad or after the
Bell Cutoff time. The Silenced LED turns off if the alarm sounds again or when a Sensor Reset
is performed.
Surface and Backbox
Mounting Holes
Surface and Backbox
Mounting Holes
Guide Tabs
Reference Card
Surface and Backbox
Mounting Holes
Surface and Backbox
Mounting Holes
Surface and Backbox Mounting Holes
Combined 4-Square
and 3-Gang Switch Box
Mounting Holes Black - 10
(Ground)
Green - 9
(Panel to Keypad Data)
Yellow - 8
(Keypad to Panel Data)
Red - 7
(Auxiliary Power)
Figure 1: 692F Wiring and Mounting Diagram

LT-0317 1.01 © 2008 Digital Monitoring Products, Inc.
800-641-4282
www.dmp.com
Made in the USA
INTRUSION • FIRE • ACCESS • NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
8365
Yellow Trouble LED turns on when the panel has failed to
communicate with the central station receiver after 10
attempts, or when phone line 1 or 2 is in a bad condition. The
Trouble LED turns off after a successful communication to
the central station, or when the phone line(s) are restored to
normal. The yellow Trouble LED also ashes if the keypad loses
communication with the panel.
Green Power LED turns on steady when there is AC or DC power
to the panel, and is off when power is lost. The Power LED
ashes when the panel’s battery is low or missing.
Keypad Function Keys
SILENCE - Press the SILENCE key and enter the user code to
silence a system alarm and the keypad sounder. You may also
use the SILENCE key to silence the bells during the Fire Drill function.
RESET - Press the RESET key and enter the user code (or press COMMAND 47) to reset a zone after an alarm. This
resets all zone alarm LEDs and momentarily drops power to the panel’s zones 2 to 5 and smoke power output.
TEST - Press the TEST function key and enter the user code (or press COMMAND 41) to initiate the panel’s System
Test function. This test rings the panel bells for 2 seconds, checks the battery charge level, and sends a system test
report to the central station on monitored systems.
CODE - To change the system user code, press CODE, enter the current user code followed by 0 + 1, and then enter
the new 4-digit user code. (The user code must always be 4 digits.)
SPECIAL- Pressing the SPECIAL key and entering the user code initiates the Fire Drill function. The Fire Drill sounds
the alarm bells and keypad sounder for the duration of the Bell Cutoff time. If the Bell Cutoff time is set to zero, the
Fire Drill will continue until the bells are silenced by entering a code. No keypad LEDs are turned on and no reports
are sent to the central station during the Fire Drill. In the event of a real re during a re drill, the system will send
a report to the central station and the LED for any zone detecting a re will glow red on the 692F.
Manual Fire Alarm - To manually initiate a re alarm, press and hold the TEST and CODE keys simultaneously for
about 2 seconds until the alarm sounds.
Wiring Specications
When planning a keypad bus installation, keep in mind the following specications:
1. DMP recommends using 18 or 22-gauge unshielded wire for all keypad and LX-Bus circuits. Do Not use
twisted pair or shielded wire for LX-Bus and keypad bus data circuits. To maintain auxiliary power integrity
when using 22-gauge wire do not exceed 500 feet. When using 18-gauge wire do not exceed 1,000 feet.
2. Maximum distance for any one circuit (length of wire) is 2,500 feet regardless of the wire gauge. This
distance can be in the form of one long wire run or multiple branches with all wiring totaling no more than
2,500 feet. As wire distance from the panel increases, DC voltage on the wire decreases.
3. Maximum number of devices per 2,500 feet circuit is 40.
Note: Each panel allows a specic number of supervised keypads. Add additional keypads in the
unsupervised mode. Refer to the panel installation guide for the specic number of supervised keypads
allowed.
4. Maximum voltage drop between the panel (or auxiliary power supply) and any device is 2.0 VDC. If the
voltage at any device is less than the required level, add a regulated, power limited, power supply listed
for Fire Protective Signaling at the end of the circuit. When voltage is too low, the devices cannot operate
properly.
Refer to the LX-Bus/Keypad Bus Wiring Application Note (LT-2031) for more information. Also see the 710/710F
Module Installation Sheet (LT-0310).
Specications
Operating Voltage 8.0 to 16 VDC
Current Draw 30mA standby, 70mA max
Dimensions 5.0” H x 6.8” W x 1.1” D
Panel Compatibility
XR5FC and XR5SL
Listings and Approvals
FCC Part 15
California State Fire Marshal (CSFM)
New York City (MEA)
Underwriters Laboratories (UL) Listed
UL 864 Fire Protective Signaling
System LEDs
Zone
Alarm
LEDs
Zone Tr ouble
LEDs
Function
Keys
SPECIAL
Key
COMMAND
Key
Data Entry
Keys
Figure 2: 692F Keypad