DMP Electronics Thinline Series Installation guide

INSTALLATION AND PROGRAMMING GUIDE
7000 Series
Thinline™ and Aqualite™ Keypad

7000 Series Installation and Programming Guide | Digital Monitoring Products b
CONTENTS
Get Started ......................................... 1
What’s Included.....................................................1
What You’ll Need ..................................................1
Procedure.................................................................1
Keypad Features ..................................................2
Enter Characters ................................................. 3
Panic Key Options .............................................. 3
User Options Menu............................................. 3
Install the Keypad............................. 4
Remove the Cover.............................................. 4
Wire the Keypad.................................................. 4
Wire for Access Control ................................... 5
Wire the Electronic Lock ................................. 5
Wire the 333 Suppressor ................................. 5
Program the Panel............................ 7
Program the Keypad ........................ 8
Keypad Options................................................... 8
Custom Card Format...................... 10
Additional Programming.................................13
Test the Keypad ...............................14
End User Training ............................15
Keypad Arming and Disarming ....................15
Keypad Access Control ...................................16
Keypad Entry Delay ..........................................16
Reference..........................................17
ULC Commercial Burglary .............................. 17
Keypad Bus Wiring Specifications.............. 17
Compatibility ....................................................... 17
Public Card Formats......................................... 17
Readers and Credentials.................................18
Specifications...................................19
Certifications....................................19
Underwriters Laboratory (UL) Listed ........19
FCC Information ................................................20
Industry Canada Information .......................20

7000 Series Installation and Programming Guide | Digital Monitoring Products 1
GET STARTED
Thinline™ Series and Aqualite™ Series LCD keypads oer flexible features and functionality. Each keypad provides:
▶Custom 16-character home or business name in the display
▶Four 2-button panic keys
▶AC Power/Armed LED
▶32-character display
▶Backlit keyboard and DMP logo
▶Internal speaker
▶Red keyboard lighting in alarm conditions
▶Simple harness connection to 4-wire keypad bus
▶Optional backboxes for conduit or wall mount applications
Models 7070/A, 7073/A, 7170, and 7173
Provides four fully-programmable, Class B, Style A, supervised, power limited protection zones that can be
programmed for a variety of burglary and access control applications.
Models 7063/A, 7073/A, 7163, and 7173
Provides a built-in proximity card reader designed to read 125KHz proximity credentials.
Models 7073/A and 7173
Provides a door strike relay and allows Wiegand input from external card readers.
What’s Included
▶One 7000 Series Keypad
▶Icon Stickers
▶Four screws (#6 x 1”)
▶One Model 333 Suppressor
▶Four 1k Ohm EOL resistors
What You’ll Need
▶5/64” (2.0mm) drill bit
▶#2 Phillips screwdriver
Procedure
To install a 7000 Series Keypad, this guide walks you through these required steps:
1. Enter characters.
2. Install the keypad.
3. Program the panel.
4. Program the keypad.
5. Custom card format.
6. Test the keypad.
7. End user training.

7000 Series Installation and Programming Guide | Digital Monitoring Products 2
INSTALL THE KEYPAD
1 Remove the Cover
The keypad housing is made up of two parts: the cover, which contains the
circuit board and components, and the base. When removing the cover, refer
to Figure 1.
To separate the keypad cover from the base, insert the flat tip of a slotted
screwdriver into one of the slots on the bottom of the keypad, then press
in slightly to disengage the tab and pry open. Repeat with the other slot.
Remove the cover from the base and set aside.
2
Wire the Keypad
To wire the keypad, make the connections shown in Figure 2. To wire external readers to the keypad, make the
connections shown in Figure 3 as required for your installation.
Caution: Disconnect all power before wiring. Failure to do so may result in equipment damage or injury.
Observe polarity when making power connections.
Each keypad model has specific wiring assignments. All zones are supervised and suitable for residential burglary
or fire applications. The maximum zone line impedance is 100 Ohms. The ground fault is detected at 1420 Ohms
or less. See “Keypad Bus Wiring Specifications” in this document for additional wiring information.
Use 1kOhm EOL resistors, DMP Model 311 on keypad zones 1-4.
1. Connect the harness to the keypad header.
2. Connect red wire to panel terminal 7.
3. Connect yellow wire to panel terminal 8.
4. Connect green wire to panel terminal 9.
5. Connect black wire to panel terminal 10.
Models 7060/A, 7063/A, 7160, and 7163
Supplied with a 4-wire harness for panel keypad bus connection.
Models 7070/A, 7073/A, 7170, and 7173
Supplied with a 12-wire data bus/zone harness. Four wires connect to the keypad bus. The remaining eight wires
are for the four zone inputs, four wires for each zone.
Models 7073/A and 7173
Supplied with a 5-wire output/reader harness and a 12-wire data bus/zone harness.
Cover
Base
Figure 1: Separate the Keypad Housing

7000 Series Installation and Programming Guide | Digital Monitoring Products 3
ExternalReader/Door Strike
7073/7073A, 7173 Keypads
All Keypads
Zones 1-4
7070/7070A
7073/7073A
7170/7173 Keypads
All zones are supervised and suitable for fire applications.
Maximum zone line impendence is 100 Ohms.
Ground fault detected at 1420 Ohms or less.
Surface and Backbox
Mounting Holes
Combined 4-square
and 3-gang switch box
Mounting Holes
Surface and Backbox
Mounting Holes
Violet - Door Strike, Normally Closed
Gray - Door Strike, Common
Orange - Door Strike, Normally Open
White/Green - Reader Data 0
White - Reader Data 1
Black - Ground
Green - Receive Data
Yellow - Send Data
Red - Power
White/Yellow - Zone 4
1k Ω
White/Orange - Zone 3 1k Ω
White/Red - Zone 2
1k Ω
White/Brown - Zone 1 1k Ω
Figure 2: Keypad Back Showing Wiring Harness Assignments
WIRE COLOR PURPOSE WIRE COLOR PURPOSE
Black Ground from Panel* Violet Door Strike, NC
Green Receive Data from Panel* Gray Door Strike, C
Yellow Send Data from Panel* Orange Door Strike, NO
Red Power from Panel* White/Brown Zone 1
Black Ground to Reader White/Red Zone 2
Red Power to Reader White/Orange Zone 3
White Reader Data 1 White/Yellow Zone 4
White/Green Reader Data 0
*Required connections
Additional Power Supply
If the current draw for all keypads exceeds the panel output, provide additional current by adding a Model 505-12
auxiliary power supply.
1. Connect all keypad black ground wires to the power supply negative terminal.
2. Run a jumper wire from the power supply negative terminal to the panel common ground terminal.
3. Connect all keypad power (+12VDC) wires to the power supply positive terminal.
Caution: Do not connect the power supply positive terminal to any panel terminal. Refer to the 505-12 Power
Supply Installation Guide (LT-0453) if needed.
Keypad Bus Monitor
For listed fire protective systems, the 893A Module or 277 Trouble Sounder must be installed on the XR150/XR550
Series panel to monitor the keypad bus. It should be programmed to sound when the keypad bus fails to operate.

7000 Series Installation and Programming Guide | Digital Monitoring Products 4
3 Wire for Access Control (Optional)
Internal Access Control Reader
The 7063/A, 7073/A, 7163, and 7173 keypads provide a built-in proximity card reader that is compatible with most
standard 125kHz proximity credentials. An external 13.56 MHZ proximity reader can be connected and will be
compatible with 13.56 MHz proximity credentials. For a list of publicly supported card formats, see Public Card
Formats.
Note: Some proximity credentials are not compatible with DMP proximity keypads. Test the intended
proximity credentials with the application before installation. DMP does not guarantee compatibility with
credentials not purchased from DMP.
External Access Control Reader
To accept Wiegand data input from other external card readers, connect a 12VDC external reader to a 7073/A or
7173 keypad. Connect the red and black power wires from the reader to the power wires from the panel. These
connect in parallel with the keypad power wires. Connect the reader (Data 1) wire to the white wire on the 5–wire
keypad cable. Connect the reader (Data 0) wire to the green/white wire on the 5–wire keypad cable. See Figure 2.
Violet - Door Strike, Normally Closed
Gray - Door Strike, Common
Orange - Door Strike, Normally Open
White/Green - Reader Data 0
White - Reader Data 1
Black - Ground
Green - Receive Data
Yellow - Send Data
Red - Keypad Power
White/Yellow - Zone 4 1k Ω
White/Orange - Zone 3 Request to Exit (option) 1k Ω
White/Red - Zone 2 Door Contact (option)
1k Ω
White/Brown - Zone 1 7/0 Panic (option)
1k Ω
External Card
Reader
To Keypad Bus
Figure 3: Access Control Wiring
Wire the Electronic Lock
The 7073/A and 7173 keypads provide a Form C (SPDT) relay for controlling locks and other electronically-
controlled barriers. The Form C relay draws up to 15 mA of current and the contacts are rated for 1 Amp at 30
VDC maximum, resistive. The wires marked NO C NC allow you to connect the device wiring to the relay for
module control. Use an additional power supply to power magnetic locks and door strikes. See Figure 6.
Wire the 333 Suppressor
Use the included 333 suppressor with the keypad to suppress any surges cause by energizing a magnetic lock or
door strike. Install the 333 across the keypad C (common and NO (normally open) or NC (normally closed wires.
If the device being controlled by the relay is connected to the NO and C wires, install the suppressor on the NO
and C wires. Conversely, if the devices is connected to the NC and C wires, install the 333 suppressor on NC and C
wires. See Figure 6.

7000 Series Installation and Programming Guide | Digital Monitoring Products 5
Green/White – D0
White – D1
Orange – N/O
Gray – C
Violet – N/C
NC
C
NO
WHT
GRN
None
To Keypad
Magnetic Door Lock
Normally Closed
Normally Closed Normally Open
Common
Power Supply
Model 333
Supressor
NC
C
NO
WHT
GRN
None
To Keypad
Door Strike Relay
Normally Opem
Common
Power Supply
Model 333
Supressor
Figure 4: 5-Wire Harness and 333 Suppressor Installation
4
Mount the Keypad
All DMP keypad housings are designed to install on any 4” square box, 3-gang switch box, compatible backboxes,
or directly on a flat surface.
1. Route the keypad wires through the cutouts in the
base. See Figure 7.
2. Use the keypad base to mark the holes for the
screws on the mounting surface.
3. Set the base aside and drill the holes.
4. Use the included screws to secure the keypad
base to the surface. Do not overtighten.
5. When all wire connections have been completed,
place the keypad cover back onto the base and
snap it into place.
A
A
A
A
B
B
D
B
B
C
C
DD
D
A
B
Backbox
mounting holes
Switchbox
mounting holes
CWiring cutouts
DCover latches
Figure 5: Mounting Hole Locations
Door Strike Relay Operation
When the user code sent from the reader is verified by the panel, the keypad door strike relay activates for five
seconds. During this time, the access door connected to Zone 2 must be opened to start the programmed entry/exit
timer and Zone Bypass if programmed and used. The five second door strike is panel programmable when the keypad
is used on an XR150/XR550 Series panel.
Zone 2 Door Contact with Bypass
If the door being released by the 7073/A and 7173 keypad is protected, you can provide a programmed bypass time
by connecting its contact to Zone 2 (white/red pair) on the keypad and enabling the bypass feature. Door contacts
may be N/C or N/O.
Zone 3 Request to Exit
You can also connect a N/O PIR (or other motion sensing device) or a mechanical switch to Zone 3 (white/orange
pair) on the 7073/A and 7173 keypad to provide Request to Exit (REX) capability. When Zone 3 shorts, the keypad
relay activates for 5 seconds. During this time, the user can open the protected door to start the programmed Bypass
entry/exit timer. If the door is not opened within five seconds, the relay restores to its locked state.
A Zone 3 REX is inhibited for three seconds after the keypad reads a card and a door strike occurs. This is to allow
area entry and pass under a REX PIR. For zone 3 REX when shorted, the lock relay will not activate and the zone 2
bypass begins (normally with electric strikes). If Zone 3 goes open, the lock relay will activate for the programmed
REX time and the zone 2 bypass begins (standard with magnetic locks).

7000 Series Installation and Programming Guide | Digital Monitoring Products 6
Keypad Features
FRI 2:52 PM
A
C
B
D
F
E
G
I
H
J
L
K
V
X
W
S
U
T
P
R
Q
M
O
N
Y
Z
E
N
T
E
R
B
A
C
K
ALL RESET HOME
CHIME PERIM SLEEP
1 2 3 4
5 6 7 8
9 0
CMD
A
POWE
R
R
M
E
D
Panic Keys
Power LED
Armed LED
Proximity
Credential
Reader and
Backlit Logo
32-Character
Display
Select Keys
Command Key
Back Arrow Key
Figure 6: 7000 Series LCD Keypad
1 2 3 4
5 6 7 8
9 0
A
C
B
D
F
E
G
I
H
J
L
K
V
X
W
S
U
T
P
R
Q
M
O
N
Y
Z
B
A
C
K
CMD
ABC SECURITY
FRI 2: 52 PM
POWER
ARMED
Command Key
Select Keys
32-Character
Display
Power LED
Armed LED
Back Arrow Key
Proximity
Credential
Reader and
Backlit Logo
Panic Keys
Figure 7: 7100 Series LCD Keypad

7000 Series Installation and Programming Guide | Digital Monitoring Products 7
Enter Characters
Number Pad
1. Choose a character from the table. Use the Greek Characters table if Greek was selected as the keypad
language setting.
2. Identify the Number the character correlates with and press that number on the number pad.
3. Identify the Select Key for the character and press that select key on the keypad. Press that select key again for
the lowercase letter (Latin characters only).
4. When the desired character displays on the keypad, return to step 1 to enter another character or press CMD if
finished.
Table 1: Latin Characters
NUMBER SELECT KEY
1 2 3 4
1 A B C ( [ {
2 D E F ) ] }
3 G H I ! ^ ~
4 J K L ? “ |
5 M N O / \ `
6 P Q R & $
7 S T U @ %
8 V W X , =
9 Y Z Space : _ ;
0 - + . ‘ * < # >
NUMBER SELECT KEY
1 2 3 4
1 Α Β Γ ( [ {
2 Δ Ε Ζ ) ] }
3 Η Θ Ι ! ^ ~
4 Κ Λ Μ ? “ |
5 Ν Ξ Ο / \ `
6 Π Ρ Σ & $
7 Τ Υ Φ @ %
8 Χ Ψ Ω , =
9 Space Space Space : _ ;
0 - + . ‘ * < # >
Table 2: Greek Characters

7000 Series Installation and Programming Guide | Digital Monitoring Products 8
Panic Key Options
2-Button Panic Keys
All keypads oer a panic key function that allows users to send panic, emergency, or fire reports to the central station
in an emergency. Enable the panic key function in the keypad user menu. Place the supplied icon stickers below the
top row select keys. The user must press and hold the two select keys for two seconds until a beep is heard.
▶Panic (left two select keys)—Zone 19 + Device Address
▶Emergency Non-Medical (center two select keys)—Zone 29 + Device Address
▶Fire (right two select keys)—Zone 39 + Device Address
User Options Menu
To access the Options menu, press and hold the back arrow and CMD keys for 2 seconds.
Backlighting Brightness
Adjust the LCD display brightness level, power and armed LEDs, the keyboard, and the logo backlighting. At SET
BRIGHTNESS, use the left select key to decrease the brightness and the right select key to increase the brightness. If
the brightness level is lowered, it reverts to maximum intensity whenever a key is pressed. If no keys are pressed, and
the speaker has not sounded for 30 seconds, the user-selected brightness level restores.
Internal Speaker Tone
Adjust the keypad internal speaker tone. At SET TONE, use the left select key to decrease the tone and the right
select key to increase the tone.
Internal Volume Level
Adjust the keypad internal speaker volume for key presses and entry delay tone conditions. During alarm and trouble
conditions, the volume is always at maximum level. At SET VOLUME LEVEL, use the left select key to decrease the
volume and the right select key to increase the volume.
Model Number
Displays the keypad model number, firmware version, and date.
Keypad Address
Displays the current keypad address.