Dormakaba ED250 User manual

ED250
Installation in In-ground Case
Installation Instructions
DL4614-070 – 08-2018
| EN |

2ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Blank page
This page left intentionally blank.

3
ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Warranty guidelines
Warranty guidelines
 Installation guidelines affecting warranty
. Opcon cement case enclosure.
Opcon cement case enclosure is listed and labeled as a
NEMA  water resistant enclosure under UL ,
Enclosures for electrical equipment, non-environmental
considerations, and CSA ., Special purpose electrical
enclosures industrial products.
Conformance with the following installation and service
procedures must be maintained to assure a proper
installation and to maintain the Opcon warranty.
. Enclosure penetrations: The cement case must only
be penetrated to install electric power service and
low voltage signal wires.
Liquidtight fittings: Opcon approved liquidtight
fittings shall be used (Ref. Chapter ) at all
electrical case penetrations. The liquidtight
fittings may only be placed as outlined in
Chapter  of this manual.
Use of liquidtight fittings is a National Electrical
Code requirement and is also an Opcon specification.
Cement case cover: Attachments to the cement case
cover are not permitted.
. Drain system.
In certain exterior conditions (downgrade elevation,
openings with direct contact to precipitation, extreme
humidity, or other similar conditions) a drain system or
provision from the cement case is recommended.
CAUTION
Drain system penetration into case will void
NEMA  enclosure rating.
. Seals
All seals provided with the Opcon system must be
installed including the following:
. Spindle seal cement case cover Ref. Chapter .
. Spindle seal at threshold, Ref. Chapter .
. Perimeter gasket between cement case and cover.
. Double door connector PVC conduit fittings and PVC
conduit at cement case are sealed with a special
silicone. Ref. Chapter . Any damage to the silicone
seal in these areas must be repaired.
SPECIAL NOTE ON SEALS. ANY SEAL FOUND TO BE
DAMAGED OR WORN MUST BE REPLACED
IMMEDIATELY TO MAINTAIN THE UL AND CSA
LISTINGS AS WELL AS OPCON SPECIFICATIONS AND
WARRANTY.
. Floor covers (thresholds)
Reference Chapter .
. All floor covers must be manufactured by Opcon or
manufactured to Opcon specifications.
. Floor covers must be:
• Manufactured to accept all seals.
• Removable for future service.
• Attached to the surrounding floor without
penetrating the cement case or cement case cover.
. All floor covers must have a perimeter seal of silicone
or a similar water proofing sealant applied to keep
water from encroaching between the cement case
cover and the floor cover.
. Technicians
. dormakaba USA Inc. and Opcon must certify
installation and service technicians.
. Technicians must also be certified by American
Association of Door Manufacturers (AAADM).
. Installation or servicing the Opcon system or
automatic equipment using non-certified technicians
will void this warranty.
. Pressure washing.
. Pressure washing is never permitted at or near the
Opcon installation.

4ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Table of Contents
Warranty guidelines 
Table of contents 
 General information 
 Product description 
 Safety information 
 ED in-ground door configurations 
. ED in-ground single swing door with
offset pivot arm 
. ED in-ground single swing door with
center hung arm 
. ED in-ground single swing door with
arm and track 
. ED in-ground double swing doors 
 ED in-ground packages 
 ED in-ground cement case assembly 
. ED in-ground cement case overall
assembly 
. ED in-ground cement case internal
assembly 
 Technical data 
. ED Technical data 
. Operating specifications 
 Operational mode overview 
. ED door closer modes 
 Recommended tools and torque chart 
. Recommended tools 
. Standard tightening torque 
. Drill bits 
 User interface 
. Overview 
.  button keypad and display 
. Program switch, RJ panels 
. Optional key switch panels 
 System accessories 
. System accessory electrical connections,
in-ground cement case 
. System accessories 
. ED terminal board interfaces 
 ED door signage 
. Low energy operator 
. Door signage, low energy swing doors,
initiation of door operation 
. Safety information label, low energy
swing doors 
 ED in ground installation templates 
. Center hung door 
. /" offset pivot door 
. Bottom arm and track 
Table of contents
 Door frame and door preparation 
. Install offset hung pivot in top of door
frame 
. Install center hung pivot in top of door
frame 
. Install butt hinge in side of door frame,
slide track door 
. Install door swing hardware 
 Prepare cement case for installation 
. Remove cement case cover 
. System accessory wiring into cement case,
single door 
. System accessory wiring into cement
cases, double door 
. Liquidtight conduit entry locations into
cement case 
. Liquidtight conduit and conduit fitting
requirements 
.  Vac wiring into cement case 
. Additional accessory wiring into cement
case 
. Internal cement case checks 

5
ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Table of Contents
 In-ground case installation 
. Verify concrete floor blockout 
. Install cement case, single door 
. Install cement cases, double door 
. Locate center of cement case spindle 
. Reinstall cement case cover 
. Anchoring cement pour in blockout around
bottom one inch of cement case 
. Remove cement case cover. 
. Single door, install and terminate  Vac
liquidtight conduit and wiring 
. Double doors, install and terminate
 Vac liquidtight conduit and wiring 
. Single door, install PVC reducer fitting
and PVC pipe 
. Single door, route accessory wiring into
cement case 
. Double doors, install PVC reducer fittings
and PVC pipe 
. Double doors, route accessory wiring into
cement cases 
. Double doors, install case to case  Vac
cable 
. Rotate cement case spindle to enable
door hanging 
.. Set braking circuit plug position 
.. Set AS installation type parameter 
.. Initiate learning cycle to rotate spindle
to door hanging position 
. Set operator spring tension 
. Install program switch panel
Install RJ plate assembly (double doors
only) 
. Hang door 
. Reinstall cement case cover 
. Final anchoring cement pour 
. Remove cement case cover for ED
commissioning 
. Cement case chain tension 
. Cement case spindle height adjustment 
. Spindle centering 
 Measure door width, set reveal depth 
. Door width parameter Tb 
. Tb parameter values 
 Set reveal depth 
. Reveal depth parameter rd 
. rd parameter values 
 Power fail closing speed 
. Set power fail closing speed 
 Parameters 
. Parameters 
 Single door first commissioning 
. First commissioning 
. Set configuration parameter 
. Verify driving parameters for low energy
operation 
. Perform learning cycle 
 Double door first commissioning 
. Separately commission active and passive
doors 
. Set operator parameters for double door
operation 
. Connect communication cable between
operators 
 Connect accessory wiring 
. Connect accessory wiring, single door 
. Connect accessory wiring, double doors 
 ANSI/BHMA standards 
. A. Low energy power operated
doors 
 Install cement case cover 
. Install cement case cover 
 Install door threshold 
. Install door threshold 
 Install door signage 
. Install door signage 
 Upgrade cards 
. Upgrade cards 
. Container module 
. Installing upgrade cards 
Appendix A - Wiring diagrams 
A. DX-C Key Switch Panel with
RJ connector 
A. DX-C Key Switch Panel 

6ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Chapter 1
. Installation instructions
This manual provides installation instructions for
ED in ground cement case used in single door and
pair door installations.
. Manual storage
This document must be kept in a secure place, and
accessible for reference as required.
If the door system should be transferred to another
facility, insure that this document is transferred as well.
. dormakaba.com website
Manuals are available for review, download, and printing
on the dormakaba.com website.
. Symbols used in these instructions
WARNING
This symbol warns of hazards which could result
in personal injury or threat to health.
NOTICE
Draws attention to important information
presented in this document.
 General information
TIPS AND RECOMMENDATIONS
Clarifies instructions or other information
presented in this document.
. Dimensions
Unless otherwise specified, all dimensions are given in
inches (“).
. Building codes and standards
ED in ground installation: observe applicable
national and local building codes.
CAUTION
This symbol warns of a potentially unsafe
procedure or situation.

7
ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Chapter 2
 Product description
. Intended use.
The ED is an electromechanical operator used
exclusively for opening and closing interior or exterior
swing doors.
The ED operator is packaged in a cement case for
in-ground floor installations.
For double swing doors, two cement cases are supplied.
. ED low energy operator.
CAUTION
ED in-ground is configured as a low
energy operator from factory.
2.4 Maximum door weights.
TIPS AND RECOMMENDATIONS
Insure operator is qualified for use at the
respective smoke or fire-rated door.
. Cement case enclosure.
The cement case enclosure is listed and labeled to:
• UL, NEMA  water resistant enclosure..
• CSA .
. Hardware packages.
. Refer to Chapter  for details of hardware contained
in each in ground package.
. Floor threshold.
. Threshold to cover cement case is not supplied with
the ED in-ground package. Refer to Chapter 
for threshold installation instructions..
Fig. 2.1.1 In-ground case with ED250 operator
Fig. 2.3.3 Arm and track assembly (track in door)
Fig. 2.3.1 Center hung
Fig. 2.3.2 Offset pivot
Threshold
Fig. 2.3.4 Floor threshold
1Track
2Slide
12
3
4
3Arm
4M8 shoulder screw
. Arm configurations.
Door width
ED
Inches mm Pounds kg
 .  
 .  
 .  
 .  
   
   

8ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Chapter 3
. Safety instructions
This document contains important instructions for
installation of the ED in ground operator.
Review these instructions thoroughly prior to
installation, and follow them carefully during installation,
commissioning, troubleshooting and maintenance.
. Door signage requirements
Proper signs and labels shall be applied and maintained on
the door controlled by the ED in-ground operator as
referenced in:
• ANSI/BHMA A.: Standard for power assist and
low energy power operated doors.
• Reference Chapter , Door signage.
. Safety warnings
WARNING
Damage to equipment or incorrect equipment
operation may result from an incorrect installation.
WARNING
Hazard to mechanical processes by use of
control settings, elements, or procedures not
documented in this manual!
WARNING
Electric shock hazard!
By use of control elements, settings, or
procedures not documented in this manual!
WARNING
Work on electrical equipment and  Vac
wiring installation must be performed only by
qualified personnel!
WARNING
Metallic doors must be grounded per national
and local codes!
 Safety information
WARNING
Hand pinch point and crushing hazards at door
closing edges!
WARNING
Crushing hazards at door closing edges!
. Residual hazards
WARNING
After installation, hazards such as minor
crushing, impact with limited force, and risk to
unsupervised children may exist depending on
structural design of door area, type of door,
and any safeguards that have been
implemented.
Fig. 3.1 Door closing edges
Opposing
closing edge
Main
closing edge
Secondary
closing edge

9
ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Chapter 4
 ED in-ground door configurations
. ED in-ground single swing door with offset pivot arm
1
2
3
4
5
15
Fig. 4.1.1 RH door with offset pivot arm
1ED250 in-ground
cement case
2Offset pivot arm
3Door pivot (by
others)
4Door frame pivot
(By others)
5Door frame
6Blockout
• Threshold not
shown
• Door transparent
for hardware views
12
2
13
4
5
5
1
Fig. 4.1.2 LH door with offset pivot arm
Fig. 4.1.1.1 Overhead view
Fig. 4.1.2.1 Overhead view
TIPS AND RECOMMENDATIONS
Door frames and doors are shown
transparent to provide hinge
views.
TIPS AND RECOMMENDATIONS
Door thresholds are not shown to
provide in ground cement case
and arm views.
1ED250 in-ground
cement case
2Offset pivot arm
3Door pivot (by
others)
4Door frame pivot
(By others)
5Door frame
6Blockout
• Threshold not
shown
• Door transparent
for hardware views 2
3

10 ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Chapter 4
Fig. 4.2.1 Door with center hung arm Fig. 4.2.1.1 Overhead view
1ED250 in-ground
cement case
2Blockout
5Door frame
6Center hung arm
9Top of door and
door frame
hardware
(by others)
Threshold not shown
. ED in-ground single swing door with center hung arm
Fig. 4.3.1 LH door with arm and track
. ED in-ground single swing door with arm and track
Fig. 4.3.1.1 Overhead view, door closed
1ED250 in-ground
cement case
2Blockout
3Door
4Butt hinge
(by others)
7Track
8Arm
9Threshold
(by others)
Fig. 4.3.2 RH door with arm and track
Fig. 4.3.2.2 Front view
7
8
1
23
Fig. 4.3.1.2 Front view
2
1
78
Fig. 4.3.2.1 Overhead view, door closed
12
7
8
3
4
6
1
69
1
5
8
7
21
1
6
2
9
7
8
4
1ED250 in-ground
cement case
2Blockout
3Door
4Butt hinge
(by others)
7Track
8Arm
9Threshold
(by others)
9
7
8
4

11
ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Chapter 4
. ED in-ground double swing doors
Fig. 4.4.1 Double doors with offset pivot arms
1
2
1ED250 in-ground
cement case
2 Offset pivot arm
1
6
Fig. 4.4.2 Double doors with center hung arms
12
1 6
1ED250 in-ground
cement case
6 Center hung arm
Fig. 4.4.3 Double doors with arm and track
1ED250 in-ground
cement case
2Blockout
4Butt hinge
7 Track
8Arm
1
2
1
4
4
7
8
78

12 ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Chapter 5
 ED in-ground packages
. Center hung single door
Fig. 5.1.1 ED250 in-ground cement case assembly
1ED250 in-ground
cement case
Fig. 5.1.2 Decals, low energy DK3137-010
6
1Center hung arm
2PVC reducer
coupling for case
2 3/8" hole,
1 1/2" PVC pipe
Fig. 5.1.6 RJ45 communication cable
Fig. 5.1.5 Center hung arm
1
Mounting screws supplied with arm.
2
Fig. 5.1.7 PVC reducer coupling
1
1 DD0586-010
2DD0758-010
3DD0762-010
4DD0762-020
8Safety Information
label, low energy
1Program switch
panel DX4604-020
1.1 Program switch
1.2 Comm. port for
dormakaba
handheld
1.3 Exit only switch,
5Cable, 10'
6RJ45 communication
cable,10',
DX4607-020
6.1 RJ45 port
8Key switch panel,
RJ45, DX4604-21C
9Key switch panel
DX4604-11C
Fig. 5.1.3 Program switch panel
1
1.2
1.3
1.1
Fig. 5.1.4 Optional key switch panels
8
9
5
6.1
SAFETY INFORMATION
Low Energy Swinging
Doors
1
. Activate the door. Door
shouldopen at a slow
smooth pace (4 or more
seconds), and stop withou
t
impact.
2
. Door must remain fully open
for a minimumof 5 seconds
before beginningto close.
3
. Door should closeat a slow,
smooth pace (4 or more
seconds), and stop without
impact.
4
. Inspect the floor area. It
should be clean with no
loose partsthatmight cause
user to trip or fall. Keep
traffic path clear.
5
. Inspect door‘s overall
condition. The appropriate
signageshould be present
andthe hardware should
be in good condition.
6
. Have door inspected by an
AAADM certified inspector
at least annually.
AAADM
American Association o f Automatic
Door Manufacturer s
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.19 ON:
DATE:______________
by AAADM Certified
Inspector
Number:___________
AAADM-3044
DO NOT USE DOOR if it fails
any of these safety checks of if
it malfunctions in any way. Call
a qualified automatic door
service company to have door
repaired or serviced.
See Owner’s manual or
instructions for details on
each of these and other
safety items. If you need
a copy of the manual,
contact the manufacturer.
These minimum safety checks,
in addition to those in the
Owner’s Manual, should be
made each day and after any
loss of electrical power.
1
3
4
2
8
DD0758-010
ACTIVATE SWITCH
TO OPERATE
DD0758-010
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0762-020
PULL
TO OPERATE
DD0762-010
PUSH
TO OPERATE

13
ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Chapter 5
1
. Center hung double door
Fig. 5.2.1 ED250 in-ground cement case assemblies
1ED250 in-ground
cement case
1Program switch
panel DX4604
1.1 Program switch,
1.2 Comm. port for
dormakaba
handheld
1.3 Exit only switch
5Cable, 10'
6RJ45 communication
cable, 10',
DX4607-020
6.1 RJ45 port
1Center hung arm
Double doors:
21 1/2" PVC pipe,
2 feet long
3PVC reducer
coupling for 2 3/8"
case hole
Fig. 5.2.4 Center hung arms
2
3
3
Fig. 5.2.5 115 Vac power and
communication cables
1
1
Mounting screws supplied with arms.
1 115 Vac power cable
,11', DX3484-030
2Communication
cable, 80"
DX3485-030
3RJ45 plug
6RJ45 communication
cable, 10',
DX4607-020
7RJ45 plate
assembly
DX4604-31C
1
1
Fig. 5.2.2 Decals, low energy, DK3137-030
2 sets
1 DD0586-010
2DD0758-010
3DD0762-010
4DD0762-020
8Safety Information
label, low energy
Fig. 5.2.3 Program switch, RJ45 panels
1
1.1
1.2
1.2
5
6.1
6.1
1.2
6
Fig. 5.2.6 RJ45 communication cable
Fig. 5.2.7 In ground pair conduit install kit
Fig. 5.2.8 Comm. cable for dormakaba handheld
6
Fig. 5.2.9 Optional key switch panels
2
3
8
9
SAFETY INFORMATION
Low Energy Swinging
Doors
1
. Activate the door. Door
shouldopen at a slow
smooth pace (4 or more
seconds), and stop withou
t
impact.
2
. Door must remain fully open
for a minimumof 5 seconds
before beginningto close.
3
. Door should closeat a slow,
smooth pace (4 or more
seconds), and stop without
impact.
4
. Inspect the floor area. It
should be clean with no
loose partsthatmight cause
user to trip or fall. Keep
traffic path clear.
5
. Inspect door‘s overall
condition. The appropriate
signageshould be present
andthe hardware should
be in good condition.
6
. Have door inspected by an
AAADM certified inspector
at least annually.
AAADM
American Association o f Automatic
Door Manufacturer s
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.19 ON:
DATE:______________
by AAADM Certified
Inspector
Number:___________
AAADM-3044
DO NOT USE DOOR if it fails
any of these safety checks of if
it malfunctions in any way. Call
a qualified automatic door
service company to have door
repaired or serviced.
See Owner’s manual or
instructions for details on
each of these and other
safety items. If you need
a copy of the manual,
contact the manufacturer.
These minimum safety checks,
in addition to those in the
Owner’s Manual, should be
made each day and after any
loss of electrical power.
1
3
4
2
8
DD0758-010
ACTIVATE SWITCH
TO OPERATE
DD0758-010
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0762-020
PULL
TO OPERATE
DD0762-010
PUSH
TO OPERATE

14 ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Chapter 5
. Offset pivot single door
Fig. 5.3.1 ED250 in-ground cement case assembly
1ED250 in-ground
cement case
1Program switch
panel DX4604-020
1.1 Program switch
1.2 Comm. port for
dormakaba
handheld
1.3 Exit only switch,
5Cable, 10'
6RJ45 communication
cable,10',
DX4607-020
6.1 RJ45 port
8Key switch panel,
RJ45, DX4604-21C
9Key switch panel
DX4604-11C
6
Fig. 5.3.6 RJ45 communication cable
Fig. 5.3.5 Offset pivot arm
1
Mounting screws supplied with arm.
1Offset pivot arm
2PVC reducer
coupling 2 3/8" hole,
1 1/2" PVC pipe
2
Fig. 5.3.7 PVC reducer coupling
1
Fig. 5.3.2 Decals, low energy DK3137-010
1 DD0586-010
2DD0758-010
3DD0762-010
4DD0762-020
8Safety Information
label, low energy
Fig. 5.3.3 Program switch panel
1
1.2
1.3
1.1
Fig. 5.3.4 Optional key switch panels
8
9
5
6.1
SAFETY INFORMATION
Low Energy Swinging
Doors
1
. Activate the door. Door
shouldopen at a slow
smooth pace (4 or more
seconds), and stop withou
t
impact.
2
. Door must remain fully open
for a minimumof 5 seconds
before beginningto close.
3
. Door should closeat a slow,
smooth pace (4 or more
seconds), and stop without
impact.
4
. Inspect the floor area. It
should be clean with no
loose partsthatmight cause
user to trip or fall. Keep
traffic path clear.
5
. Inspect door‘s overall
condition. The appropriate
signageshould be present
andthe hardware should
be in good condition.
6
. Have door inspected by an
AAADM certified inspector
at least annually.
AAADM
American Association o f Automatic
Door Manufacturer s
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.19 ON:
DATE:______________
by AAADM Certified
Inspector
Number:___________
AAADM-3044
DO NOT USE DOOR if it fails
any of these safety checks of if
it malfunctions in any way. Call
a qualified automatic door
service company to have door
repaired or serviced.
See Owner’s manual or
instructions for details on
each of these and other
safety items. If you need
a copy of the manual,
contact the manufacturer.
These minimum safety checks,
in addition to those in the
Owner’s Manual, should be
made each day and after any
loss of electrical power.
1
3
4
2
8
DD0758-010
ACTIVATE SWITCH
TO OPERATE
DD0758-010
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0762-020
PULL
TO OPERATE
DD0762-010
PUSH
TO OPERATE

15
ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Chapter 5
. Offset pivot double door
Fig. 5.4.1 ED250 In ground cement case assemblies
1ED250 in ground
cement case
Fig. 5.4.3 Program switch, RJ45 panels
1Offset pivot arm
Double doors:
21 1/2" PVC pipe,
2 feet long
3PVC reducer
coupling for 2 3/8"
case hole
Fig. 5.4.4 Offset pivot arms
2
3
3
Fig. 5.4.5 115 Vac power and
communication cables
1
1
1
1
1Program switch
panel DX4604-02C
1.1 Program switch,
1.2 Comm. port for
dormakaba
handheld
1.3 Exit only switch
5Cable, 10'
6RJ45 communication
cable, 10',
DX4607-020
6.1 RJ 45 port
Mounting screws supplied with arms.
1 115 Vac power cable
,11', DX3484-030
2Communication
cable, 80"
DX3485-030
3RJ45 plug
6RJ45 communication
cable, 10',
DX4607-020
8Key switch panel,
RJ45, DX4604-21C
9Key switch panel
DX4604-11C
5
6.1
1
Fig. 5.4.2 Decals, low energy, DK3137-030,
2 sets
1 DD0586-010
2DD0758-010
3DD0762-010
4DD0762-020
8Safety Information
label, low energy
6.1
1.2
6
Fig. 5.4.6 RJ45 communication cable
Fig. 5.4.7 In ground pair conduit install kit
Fig. 5.4.8 Comm. cable for dormakaba handheld
6
Fig. 5.4.9 Optional key switch panels
2
3
8
9
1
1.2
1.3
1.1
SAFETY INFORMATION
Low Energy Swinging
Doors
1
. Activate the door. Door
shouldopen at a slow
smooth pace (4 or more
seconds), and stop withou
t
impact.
2
. Door must remain fully open
for a minimumof 5 seconds
before beginningto close.
3
. Door should closeat a slow,
smooth pace (4 or more
seconds), and stop without
impact.
4
. Inspect the floor area. It
should be clean with no
loose partsthatmight cause
user to trip or fall. Keep
traffic path clear.
5
. Inspect door‘s overall
condition. The appropriate
signageshould be present
andthe hardware should
be in good condition.
6
. Have door inspected by an
AAADM certified inspector
at least annually.
AAADM
American Association o f Automatic
Door Manufacturer s
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.19 ON:
DATE:______________
by AAADM Certified
Inspector
Number:___________
AAADM-3044
DO NOT USE DOOR if it fails
any of these safety checks of if
it malfunctions in any way. Call
a qualified automatic door
service company to have door
repaired or serviced.
See Owner’s manual or
instructions for details on
each of these and other
safety items. If you need
a copy of the manual,
contact the manufacturer.
These minimum safety checks,
in addition to those in the
Owner’s Manual, should be
made each day and after any
loss of electrical power.
1
3
4
2
8
DD0758-010
ACTIVATE SWITCH
TO OPERATE
DD0758-010
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0762-020
PULL
TO OPERATE
DD0762-010
PUSH
TO OPERATE

16 ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Chapter 5
. Arm and track single door
Fig. 5.5.1 ED250 in-ground cement case assembly
1ED250 in-ground
cement case
1Program switch
panel DX4604-020
1.1 Program switch,
1.2 Comm port for
dormakaba
handheld
3Exit only switch,
5Cable, 10'
6RJ45 communication
cable,10', DX4607-020
8Key switch panel,
RJ45, DX4604-21C
9Key switch panel
DX4604-11C
Fig. 5.5.3 Program switch panel
6
Fig. 5.5.6 RJ45 communication cable
Fig. 5.5.5 Arm and track
1
1
1.2
1.3
1.1
Mounting screws supplied with track and
arm.
1Track
2Slide
3Arm
4M8 shoulder screw
5PVC reducer
coupling for case
2 3/8" hole,
1 1/2" PVC pipe
Fig. 5.5.7 PVC reducer coupling
12
3
4
5
Fig. 5.5.2 Decals, low energy, DK3137-010
1 DD0586-010
2DD0758-010
3DD0762-010
4DD0762-020
8Safety Information
label, low energy
Fig. 5.5.4 Optional key switch panels
8
9
5
6.1
SAFETY INFORMATION
Low Energy Swinging
Doors
1
. Activate the door. Door
shouldopen at a slow
smooth pace (4 or more
seconds), and stop withou
t
impact.
2
. Door must remain fully open
for a minimumof 5 seconds
before beginningto close.
3
. Door should closeat a slow,
smooth pace (4 or more
seconds), and stop without
impact.
4
. Inspect the floor area. It
should be clean with no
loose partsthatmight cause
user to trip or fall. Keep
traffic path clear.
5
. Inspect door‘s overall
condition. The appropriate
signageshould be present
andthe hardware should
be in good condition.
6
. Have door inspected by an
AAADM certified inspector
at least annually.
AAADM
American Association o f Automatic
Door Manufacturer s
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.19 ON:
DATE:______________
by AAADM Certified
Inspector
Number:___________
AAADM-3044
DO NOT USE DOOR if it fails
any of these safety checks of if
it malfunctions in any way. Call
a qualified automatic door
service company to have door
repaired or serviced.
See Owner’s manual or
instructions for details on
each of these and other
safety items. If you need
a copy of the manual,
contact the manufacturer.
These minimum safety checks,
in addition to those in the
Owner’s Manual, should be
made each day and after any
loss of electrical power.
1
3
4
2
8
DD0758-010
ACTIVATE SWITCH
TO OPERATE
DD0758-010
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0762-020
PULL
TO OPERATE
DD0762-010
PUSH
TO OPERATE

17
ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Chapter 5
. Arm and track double door
Fig. 5.6.1 ED250 in-ground cement case assemblies
1ED250 in-ground
cement case
6
1Offset pivot arm
Double doors:
21 1/2" PVC pipe,
2 feet long
3PVC reducer
coupling for 2 3/8"
case hole
Fig. 5.6.5 RJ45 communication cable
Fig. 5.6.4 Arm and track
Fig. 5.6.6 In ground pair conduit install kit
1 115 Vac power cable
,11', DX3484-030
2Communication
cable, 80"
DX3485-030
3RJ45 plug
6RJ45 communication
cable, 10', DX4607-020
8Key switch panel,
RJ45, DX4604-21C
9Key switch panel
DX4604-11C
2
3
3
Fig. 5.6.9 115 Vac power and
communication cables
1
1
1
1
1
1Program switch
panel DX4604-02C
1.1 Program switch
1.2 Comm. port for
dormakaba
handheld
1.3 Exit only switch
5Cable, 10'
6RJ45 communication
cable, 10', DX4607-020
6.1 RJ45 comm. port
Mounting screws supplied with track.
Fig. 5.6.7 Comm. cable for dormakaba handheld
6
Fig. 5.6.2 Decals, low energy, DK3137-030 2 sets
1 DD0586-010
2DD0758-010
3DD0762-010
4DD0762-020
8Safety Information
label, low energy
Fig. 5.4.3 Program switch, RJ45 panels
1
1.1
1.2
1.2
5
6.1
6.1
1.2
Fig. 5.6.10 Optional key switch panels
2
3
8
9
SAFETY INFORMATION
Low Energy Swinging
Doors
1
. Activate the door. Door
shouldopen at a slow
smooth pace (4 or more
seconds), and stop withou
t
impact.
2
. Door must remain fully open
for a minimumof 5 seconds
before beginningto close.
3
. Door should closeat a slow,
smooth pace (4 or more
seconds), and stop without
impact.
4
. Inspect the floor area. It
should be clean with no
loose partsthatmight cause
user to trip or fall. Keep
traffic path clear.
5
. Inspect door‘s overall
condition. The appropriate
signageshould be present
andthe hardware should
be in good condition.
6
. Have door inspected by an
AAADM certified inspector
at least annually.
AAADM
American Association o f Automatic
Door Manufacturer s
ANNUAL COMPLIANCE
INSPECTION
INSPECT FOR AND
COMPLIES WITH ANSI
A156.19 ON:
DATE:______________
by AAADM Certified
Inspector
Number:___________
AAADM-3044
DO NOT USE DOOR if it fails
any of these safety checks of if
it malfunctions in any way. Call
a qualified automatic door
service company to have door
repaired or serviced.
See Owner’s manual or
instructions for details on
each of these and other
safety items. If you need
a copy of the manual,
contact the manufacturer.
These minimum safety checks,
in addition to those in the
Owner’s Manual, should be
made each day and after any
loss of electrical power.
1
3
4
2
8
DD0758-010
ACTIVATE SWITCH
TO OPERATE
DD0758-010
CAUTION
DOOR
AUTOMATIC
DD0586-010
DD0762-020
PULL
TO OPERATE
DD0762-010
PUSH
TO OPERATE

18 ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Chapter 6
. ED in-ground cement case overall assembly
2(28) 3
2
45
4
6
2
(28) 3
1
2
7
Fig. 6.1.1 ED250 in-ground case dimensions
 ED in-ground cement case assembly
1Cement case
2Cover
3Gasket
1In-ground case
2Covers
38-32 x 3/4" PFHMS
(Philips flat head
machine screw)
4Center bearing
shaft, ED250-IG
5Shaft seal
6Gasket, 1/8" thick
72 3/8" hole for PVC
reducer coupling
Fig. 6.1.2 ED250 in-ground case cover and fasteners
36”
4 7/8”
4 1/2”
5.9”
(6 1/4”
REF)
Ø 2 3/8”
2
3
1
7”

19
ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Chapter 6
7
86
3 2 159
410
Fig. 6.2.1 ED250 in-ground case component view
1ED250 in-ground
case
2Gasket, 1/8" thick
3 8-32 x 3/4" FHMSPH
(flat head machine
screw, Phillips)
4ED250 operator
5PCB bracket
assembly
6Operator drive axle
7Center bearing
shaft
8Shaft seal
9Spring tension
adjustment
10 PVC reducer fitting
. ED in-ground cement case internal assembly
Fig. 6.2.2 ED250 operator
Fig. 6.2.3 ED250 PCB bracket assembly
1PCB bracket
1.1 PCB plate
1.2 PCB plate cover
2 Accessory
connection terminal
board
3Power off/on switch
and 115 Vac
connection board
3.1 115 Vac terminal
block and
connection board
4Keypad and 2 digit
display
5Circuit board
6Braking circuit plug
receptacle
7Power fail closing
speed
potentiometer
8Program switch
connector
9Double door
operator to
operator
communication
cable port
10 dormakaba
handheld
communication port
11 Upgrade card slot
11.1 Upgrade card
socket
12 1/4 x 1/2" x 1/2"
SHCS
13 Ribbon cable
Fig. 6.2.5 115 Vac terminal block and wire
harness assembly
3
3.1
115 VAC
Neutral
Fig. 6.2.4 Operator communication
connectors, upgrade card slot
6
9
3
2
5
6
7
1
11
2
10
9
8
1.1
1.2 (7)12
13
10 9 8
11
11.1 4

20 ED250 08-2018DL4614-070
dormakaba ED250 IG Installation Instructions Chapter 7
 Technical data
Maximum wire size
Connector plug
screw size
 AWG
/”
Door
status
X
,,
Sr parameter
Door closed
Door open
Door closed, locked
Com, N.O., N.C.
contacts
.. Integrated functions
Hold open time:
Automatic opening dd parameter  to  s
NIght / bank dn parameter  to  s
Manual opening do parameter  to  s
Door blocking
behavior hd parameter Automatic, manual door modes
Electric strike
delayed opening for
locking mechanism
Ud parameter  to  s
Locking
device
feedback
X
,  Motor lock
Wind load control,
maximum Fo, Fc parameters . lb f  N
Power fail closing
speed Chapter  Adjustable with potentiometer
LED status indicators
Service manual
Green
Red
Yellow
 VDC power
Error codes
Service interval
Program and Exit
Only switches Chapter  Auto, Close, Open Exit only; Off, On
User interface Chapter   button keypad,
 digit display
Slot for dormakaba
upgrade cards Chapter  Extension of range of functions
Interface update
Service manual Firmware update
TMP, temperature
management program
Service manual
Overload protection
IDC, initial drive control Driving phase optimization
Cycle counter CC parameter  to ,,
Power assist function hA, hF, hS
parameters
Drive support for
manual opening of
door
Push & go function PG parameter Auto opening of
door at ° open
. ED Technical data
.. Required operating conditions
Ambient temperature  to  °F
Suitable for dry
rooms only
Relative air humidity:
% maximum, non-condensing
Power supply  Vac ±%, / Hz
. A maximum
Branch circuit
protection (provided
by others)
 A maximum,
dedicated branch circuit
Protection class NEMA 
Power wiring:
black, white, bare
copper (ground)
 AWG
Operating noise Maximum  db(A)
.. General specifications
In ground cement
case (W x H x D) " x  /" x ”
Internal power
supply available for
external accessories
 Vdc ± %, . A
Maximum door
opening angle  to ° depending on installation type
.. Inputs
Maximum wire size
Connector plug
screw size
 AWG
/”
Activation
inputs X* Interior, exterior N. O. contact
Safety
sensors X Swing, approach sides
Night-bank
(intercom
system)
X
,
a
- Vdc/
VAC +%
Night-bank
(key switch)
X
,  d parameter Configure for N.O. or N.C. contact
Deactivation
of drive
function
X
, a d parameter Configure for N.O. or N.C. contact
*X,terminal board numbers, reference Chapter .
Parameters, reference Chapter .
.. Outputs