Dormakaba UNIQUIN User manual

Contents
1 About this manual 2
1.1 Information about the manual 2
1.2 Other applicable documents 2
1.3 Target group 2
1.4 Symbols used 2
1.4.1 Safety instructions 2
1.4.2 Further labeling 2
2 Safety 2
2.1 Intended use 2
2.2 Foreseeable misuse 3
3 Product description 3
3.1 Example of a UNIQUIN unit 3
3.2 Product variants 3
3.2.1 Locks 3
3.2.1.1 Escape door functions 3
3.2.2 Door handle 4
3.2.3 Door fittings for locks with
escape door function 4
3.3 Parts included 4
3.3.1 Standard lock with L-shaped
handle 5
3.3.2 Lock with transmission function
E, with C-shaped handle and
fixed door knob 6
3.3.3 Lock with transit function D, with
C-shaped handle both sides 7
3.3.4 Lock with transmission function
E, with panic door fitting and
fixed door knob 8
3.3.5 Lock with transit function D, with
panic door fitting and C-shaped
handle 9
3.3.6 Standard lock with L-shaped
handle
and c-lever compact 10
3.4 Technical information 11
4 Storage and transport 11
5 Installation 12
5.1 Tools for installation 12
5.2 Installing lock with door handle set 12
5.3 Installing the lock with fixed knob 16
5.4 Installing the screw-on pates for a
panic door fitting 18
5.5 Installing the lock with c-lever
compact 18
5.6 Completing the installation with panic
door fitting 21
5.7 Completing the installation without
panic door fitting 22
6 Maintenance and care 22
6.1 Maintenance instructions 22
6.2 Cleaning instructions 22
7 Dismantling and disposal 22
7.1 Tools for dismantling 22
7.2 Dismantling the door handle 22
7.3 Dismantling the other components 23
UNIQUIN locks
EN
WN 059607 45532 – 2018-10
Mounting instructions

2UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions About this manual
1 About this
manual
1.1 Information about the
manual
This manual describes the installation of
UNIQUIN locks onto a glass door as part of
a UNIQUIN door frame system and includes
maintenance and care information.
For the complete installation of the
UNIQUIN partition wall unit, further unit
components and installation manuals may
be required as specified in the project-
related unit drawing, e.g. for the door frame
system. The illustrated unit components and
configurations are exemplary and do not
show every possible installation scenario.
The components illustrated are shown in one
opening direction as an example.
1.2 Other applicable
documents
Refer to the following technical documents
for the product:
• The project-related unit drawing
• The enclosed installation manual for the
unit components included with delivery
• The installation manuals of all unit
components
• The UNIQUIN system manual
1.3 Target group
The target group of these installation
manual is qualified personnel specially
trained in glass fitting.
1.4 Symbols used
1.4.1 Safety instructions
Safety instructions are marked with
symbols. The safety instructions are
introduced by signal words that express the
extent of the hazard, e.g.:
CAUTION
This signal word indicates a
situation of potential risk, which
could lead to minor or slight
injury if not averted.
ATTENTION
This signal word indicates a
situation of potential risk, which
could lead to damage to property
or the environment if not
averted.
TIPS AND RECOMMENDATIONS
This signal word indicates useful
information for efficient and
trouble-free operation.
1.4.2 Further labeling
2.1. Step-by-step graphics
1 2 Position numbers for parts
in diagrams
2 Safety
2.1 Intended use
This product is designed to be used to
facilitate the opening and closing of a glass
door in a door frame system as part of a
UNIQUIN unit.
• The product may only be installed with
unit components designed by dormakaba
for the installation situation and approved
according to the project-related unit
drawing.

3UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Product description
• The product may only be installed
undamaged and in accordance with the
requirements of the assembly location.
• The product may only be installed by
qualified personnel who correspond to the
defined target group.
• Only tempered safety glass (TSG) or
laminated safety glass (LSG) made of
TSG may be installed with the product.
• The product is only suitable for indoor use.
• The product is suitable for use in tropical
countries.
2.2 Foreseeable misuse
• The product is not suitable for installation
outdoors.
• The product is not suitable for installation
in the vicinity of showers, saunas,
swimming and salt-water bath or rooms
in which chemicals (e.g. chlorine) are used.
Fig. 1 Not suitable for showers, saunas, baths or
salt-water baths
3 Product
description
3.1 Example of a
UNIQUIN unit
This UNIQUIN unit is an example of a
UNIQUIN partition wall system. Further
combinations with other unit components,
e.g. with an acoustic element or a sliding
door, are possible.
Fig. 2
13
5
6
7
2
4
Example of a UNIQUIN unit
1 Ground profile and cover profile
2 Overpanel
3Side panels
4Door frame system
5Glass door
6Lock with door handle set
7Door hinges
3.2 Product variants
There are several product variants for
different areas of application.
3.2.1 Locks
There are several lock sets for different
areas of application, e.g. a lock with escape
door function for an emergency exit.
3.2.1.1 Escape door
functions
Transmission function E:
Transmission function E is an escape door
function used when doors are supposed to
prevent unauthorized access from outside
under any circumstances. The door can only
be opened with a key from outside.
It is always possible to open a door with
transmission function E from inside by using
the handle.

4UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Product description
Transit function D:
Transit function D is an escape door function
used when doors are required to allow
occasional access from outside. The door
can only be opened with a key from outside,
or if the escape door function has been
activated in advance by using the handle
from inside. It is always possible to transit
from inside to outside with transit function
D by using the handle.
3.2.2 Door handle
There are 3 different handle types (Fig. 3)
for different product combinations.
Fig. 3
1
2
3
Overview of handle types
1L-shaped handle
2 C-shaped handle
3Knob
3.2.3 Door fittings for
locks with escape
door function
There are 2 different door fittings with
special functions (Fig. 4) for particular
requirements, e.g. for transmission
functionE and different product
combinations.
Fig. 4
1
2
Overview of door fittings with special
functions
1Fixed door knob
2Panic door fitting
3.3 Parts included
The parts included vary depending on the
function required or the intended
installation scenario situation.

5UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Product description
3.3.1 Standard lock with L-shaped handle
Fig. 5
16
1 2 3 4
5 6 7
8
1314
15
9
1112
10
Example of parts included for a lock with L-shaped handle on both sides
1L-shaped handle
2Screw-on plate
3Gasket
4Door handle rose
5Mortise for lock insert
6Screws:
M6x45 for glass thickness 10–15.5 mm
M6x50 for glass thickness 16–19 mm
7Screw: M5x8 for lock insert
8Lock insert
9Door handle rose
10 Screw: M5x14 for door handle rose
11 L-shaped handle
12 Cover
13 Screw: M5x20 for base plate
14 Base plate
15 Square spindle 8 mm x 8 mm
16 Installation manual

6UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Product description
3.3.2 Lock with transmission function E, with C-shaped
handle and fixed door knob
Fig. 6
13
5 6
7 8
11
12
9
10
1 2 3 4
Example of parts included for a lock with escape door function, handle inside and fixed door knob outside
1C-shaped handle
2Screw-on plate
3Gasket
4Door handle rose
5Mortise for lock insert
6Screws:
M6x45 for glass thickness 10–15.5 mm
M6x50 for glass thickness 16–19 mm
7Base plate
8Screw: M5x20 for base plate
9Screw: M5x8 for lock insert
10 Lock insert
11 Fixed door knob with door handle rose
and square spindle 9 mm x 9 mm
12 Screw: M5x14 for door handle rose
13 Installation manual

7UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Product description
3.3.3 Lock with transit function D, with C-shaped
handle both sides
Fig. 7
16
1 2 3
5
7
8
11109
12
6
4
1314
15
Example of parts included for a lock with escape door function, handle on both sides
1C-shaped handle
2Screw-on plate
3Gasket
4Door handle rose
5Mortise outside for lock insert
6Screws:
M6x45 for glass thickness 10–15.5 mm
M6x50 for glass thickness 16–19 mm
7Screw: M5x8 for lock insert
8 Lock insert, e.g. panic lock
9Door handle rose
10 Screw: M5x14 for door handle rose inside
11 Cover
12 C-shaped handle
13 Screw: M5x20 for base plate
14 Base plate
15 Split square spindle 9 mm x 9 mm
16 Installation manual

8UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Product description
3.3.4 Lock with transmission function E, with panic
door fitting and fixed door knob
Fig. 8
6
7
8
9
2
13 4 5
1110
1314
12
19
1516
1718
20
21
Example of parts included for a lock with escape door function, panic door fitting inside and fixed door
knob
1Fixed door knob with door handle rose
and square spindle 9 mm x 9 mm
2Screw: M5x20 for base plate
3Base plate
4Screws:
M6x45 for glass thickness 10–15.5 mm
M6x50 for glass thickness 16–19 mm
5Mortise for lock insert
6Screw: M5x8 for lock insert
7Lock insert
8Gasket
9Screw-on plate for opposite side to lock
10 Base plate for panic door fitting
11 Screw: M5x10 for base plate
12 Panic door fitting
13 Screw: M5x10 for base plate
14 Base plate for panic door fitting
15 Screw: M6x20 for screw-on plate
16 Screw-on plate for the opposite side to
the hinge
17 Gasket
18 Screw-on plate for the hinge side
19 Installation manual
20 Installation manual for panic door fitting
21 Screw M5x14 for door handle rose

9UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Product description
3.3.5 Lock with transit function D, with panic door
fitting and C-shaped handle
Fig. 9
10
12
13
1415
3
1 2 4
5
6
8 9
17
20 16
1819
21
11
7
Example of parts included for a lock with escape door function, panic door fitting inside and handle
1C-shaped handle
2Cover
3Screw: M5x14 for door handle rose
4Door handle rose
5Screw: M5x20 for base plate
6Base plate
7Split square spindle 9 mm x 9 mm
8Screws:
M6x45 for glass thickness 10–15.5 mm
M6x50 for glass thickness 16–19 mm
9Mortise for lock insert
10 Screw: M5x8 for lock insert
11 Lock insert
12 Gasket
13 Screw-on plate for opposite side to lock
14 Screw: M5x10 for base plate
15 Base plate for panic door fitting
16 Installation manual for panic door fitting
17 Panic door fitting
18 Screw: M6x20 for screw-on plate
19 Screw-on plate for the opposite side to
the hinge
20 Installation manual
21 Screw-on plate for the hinge side

10 UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Product description
3.3.6 Standard lock with L-shaped handle
and c-lever compact
Fig. 10
16
1 2 3
5
7
8
11109
12
6
4
1314
15
Example of parts included for a lock with c-lever compact
1L-shaped handle with c-lever compact
and square spindle 9 mm x 9 mm
2Base plate
3Gasket
4Screw for c-lever compact
5Mortise for lock insert
6Screws:
M6x45 for glass thickness 10–15.5 mm
M6x50 for glass thickness 16–19 mm
7Screw: M5x8 for lock insert
8Lock insert
9Door handle rose
10 Screw: M5x14 for door handle rose inside
11 Cover
12 L-shaped handle
13 Screw: M5x20 for base plate
14 Base plate
15 Installation manual
16 Manual for c-lever compact

11UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Storage and transport
3.4 Technical information
Fig. 11
1108
45
659216
1043
21
Ø24
Ø24
Ø24
Glass machining on the glass door for lock
installation on the main closing edge
Fig. 12
45
199
1108
Ø24Ø24
Glass machining on the glass door for
installation of the panic door fitting on the
secondary closing edge/hinge side (optional)
4 Storage and
transport
CAUTION
Risk of crushing and impact due
to unsecured components.
Unsecured components can lead
to crushing and impact injuries
during transport.
• Wear personal protective
equipment.
• Secure components
adequately during transport.

12 UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Installation
ATTENTION
Risk of damage during transport.
Unsecured components may be
damaged during transport.
• Secure components
adequately during transport.
5 Installation
CAUTION
Risk of crushing and impact due
to unsecured components.
Unsecured components can lead
to crushing and impact injuries
during transport.
• Wear personal protective
equipment.
• Secure components
adequately during transport.
CAUTION
Risk of injury due to sharp edges.
Contact with cut edges can lead
to cuts.
• Wear protective gloves.
• Secure cut edges against
contact.
CAUTION
Risk of injury from broken glass
during installation.
Incorrect installation can lead to
broken glass and cause injuries.
• Secure the installation site.
• Wear protective clothing.
TIPS AND RECOMMENDATIONS
The installation steps are
examples for standard product
combinations. Depending on
product combination it may be
necessary to combine different
installation steps or leave them
out.
Requirements
• Before installation, ensure that the glass
machining on the glass door complies with
specifications (Fig. 11 and Fig. 12) and the
project-related unit drawing.
• Check which of the installation steps
described are required with the given
combination of products before starting
installation.
5.1 Tools for installation
• Torx angle screwdriver
• Hexagonal socket set
• Torque wrench

13UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Installation
5.2 Installing lock with
door handle set
Requirements
• The door frame system is installed.
• The opening direction of the door
complies with the project-related unit
drawing.
• The lock has the required function, e.g.
transmission function E.
• The door and door frame are suitable for
use with the intended lock, e.g. emergency
exit with panic door fitting.
1. Attach the gasket to the lock mortise
on the glass side (Fig. 13).
2. Attach the gasket to the screw-on plate
on the glass side.
Fig. 13
1.
2.
Attach the gaskets.
3. Put the door handle rose into the
screw-on plate (Fig. 14).
4. Hold the screw-on plate against the
door on the side opposite the lock
(opposite side to the hinge).
5. Hold the lock mortise against the door
on the lock side.
Fig. 14
4.
3.
5.
Attach the lock mortise and the screw-on
plate
6. Connect the lock mortise and the
screw-on plate loosely through the door
with the appropriate screws (Fig. 15).
TIPS AND RECOMMENDATIONS
Select a screw length
appropriate for the glass
thickness (see Chapter3.3).
Fig. 15
6.
Connect the lock mortise and the screw-on
plate

14 UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Installation
7. Slide the lock insert into the mortise
and fix in place (Fig. 16).
Fig. 16
7.
Slide the lock insert into the mortise and fix in
place
8. Align the lock mortise so that it is
vertically flush with the glass edge (Fig.
17).
9. Align the upper edge of the lock mortise
so that it is flush with the upper edge of
the strike plate.
Fig. 17
8.
9.
Align the lock mortise and the latch
10. Fix the lock mortise and the screw-on
plate in place with 10 Nm (see Fig. 15).
11. Put the base plate on the lock mortise
(Fig. 18).
12. Fix the base plate onto the lock mortise
with 2 screws M5x20 with 5 Nm.
13. Fix the door handle rose onto the base
plate with 2 screws M5x14 with 5 Nm.
Fig. 18
13.
12.
11.
12.
Fix the base plate onto the lock mortise
14. Observe the alignment of the square
spindle (Fig. 19).
15. Push the square spindle through the
door handle rose from the lock side into
the lock as far as it will go.

15UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Installation
Fig. 19
15.
14.
Install the square spindle.
TIPS AND RECOMMENDATIONS
With the product variant with a
fixed knob (see Chapter 5.3) the
square spindle is inserted into
the lock together with the cover
and the knob.
16. Attach the cover to the base plate (Fig.
20).
17. Fix the cover in place with screw M6x10.
Fig. 20
3.
16.
17.
Attach the cover to the base plate and fix in
place
18. Attach the door handle on the lock side
and push until you hear it click into pace
against the square spindle (Fig. 21).
TIPS AND RECOMMENDATIONS
The door handle can only be
dismantled using circlip pliers
(see Chapter 7.2).
19. Fix the door handle in place onto the
square spindle.
Fig. 21
18.
19.
Fix the door handle in place on the lock side.

16 UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Installation
20. Attach the door handle in the same way
on the opposite side from the lock and
fix in place.
TIPS AND RECOMMENDATIONS
Installation instructions for the
L-shaped handle can be followed
for other variants.
→The lock with the handle is installed.
5.3 Installing the lock with
fixed knob
Requirement
• Set-up is to include a panic door fitting.
The following installation steps show an
example of how to mount a fixed door knob
in preparation for installation of a panic
door fitting.
1. Attach the gasket on the glass side of
the lock mortise (Fig. 22).
2. Attach the gasket on the glass side to
the screw-on plate.
Fig. 22
1.
2.
Attach the gaskets.
3. Put the screw-on plate on the opposite
side to the lock against the pre-drilled
hole in the glass door (Fig. 23).
TIPS AND RECOMMENDATIONS
A base plate can be installed
instead of a screw-on plate, for
instance for a standard lock.
4. Put the lock mortise on the lock side
against the pre-drilled holes in the glass
door.
5. Connect the screw-on plate and the
lock mortise loosely with 2 screws.
TIPS AND RECOMMENDATIONS
Select a screw length
appropriate for the glass
thickness (see Chapter3.2).
Fig. 23
3.
4.
5.
Connect the lock mortise and the screw-on
plate

17UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Installation
6. Slide the lock insert into the mortise
and fix in place (Fig. 24).
Fig. 24
6.
Slide the lock insert into the mortise and fix in
place
7. Align the lock mortise so that it is
vertically flush with the glass edge (Fig.
25).
8. Align the upper edge of the lock mortise
so that it is flush with the upper edge of
the strike plate.
Fig. 25
7.
8.
Align the lock mortise and the latch
9. Fix the lock mortise and the screw-on
plate in place with 10 Nm (see Fig. 23).
10. Put the base plate on the lock mortise
(Fig. 26).
11. Fix the base plate onto the lock mortise
with 2 screws M5x20 with 5 Nm.
12. Turn the cover horizontally and insert
the door handle rose into the base plate
with the square spindle.
13. Fix the door handle rose onto the base
plate with M5x14 screw with 5 Nm.
Fig. 26
11.
13.
12.
10.
Fix the base plate onto the lock mortise

18 UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Installation
14. Ensure that the square spindle extends
beyond the screw-on plate by
max. 11 mm for installation of a panic
door fitting (Fig. 27).
TIPS AND RECOMMENDATIONS
If necessary screw the spindle to
extend it or have it lengthened
using the correct methods.
15. Attach the cover to the base plate
vertically.
16. Fix the cover onto the base plate with
screw M6x10.
Fig. 27
15.
16.
11
14.
Fixing the cover to the base plate
→The lock with the handle is installed.
5.4 Installing the screw-
on pates for a panic
door fitting
Requirement
• Set-up is to include a panic door fitting.
1. Put the screw-on plates with the
gaskets onto the pre-drilled hole in the
glass door (Fig. 28).
2. Connect the screw-on plates with 2
M6x20 screws.
Fig. 28
1.
1.
2.
Installing the screw-on plates
→The screw-on pates for a panic door
fitting are installed.
5.5 Installing the lock with
c-lever compact
Requirements
• The door frame system is installed.
• The opening direction of the door
complies with the project-related unit
drawing.
• The lock has the required functions.
• The door and door frame are suitable for
use with the intended lock.
• The c-lever compact is prepared for
installation as per the enclosed manual.
• The c-lever compact is supplied with a
105mm square spindle pre-installed.

19UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Installation
TIPS AND RECOMMENDATIONS
The length of square spindle
required for UNIQUIN is 105mm.
1. Attach the gasket to the lock mortise
on the glass side (Fig. 29).
2. Attach the gasket to the screw-on plate
on the glass side.
Fig. 29
1.
2.
Attach the gaskets.
3. Slide the lock insert into the mortise
and fix in place (Fig. 30).
Fig. 30
3.
Slide the lock insert into the mortise and fix in
place
4. Attach the c-lever compact to the
screw-on plate and fix in place with
10Nm (Fig. 31).
Fig. 31
4.
Attaching the c-lever compact to the
screw-on plate
5. Hold the screw-on plate against the
door on the side opposite the lock (Fig.
32).
6. Hold the lock mortise against the door
on the lock side.

20 UNIQUIN locks 2018-10
WN 059607 45532
dormakaba Mounting instructions Installation
Fig. 32
6.
5.
Attach the lock mortise and the screw-on
plate
7. Connect the lock mortise and the
screw-on plate loosely through the door
with the appropriate screws (Fig. 33).
TIPS AND RECOMMENDATIONS
Select a screw length
appropriate for the glass
thickness (see Chapter3.3).
Fig. 33
7.
Connect the lock mortise and the screw-on
plate
8. Align the lock mortise so that it is
vertically flush with the glass edge (Fig.
34).
9. Align the upper edge of the lock mortise
so that it is flush with the upper edge of
the strike plate.
Fig. 34
8.
9.
Align the lock mortise and the latch
10. Fix the lock mortise and the screw-on
plate in place with 10 Nm (see Fig. 33).
11. Put the base plate on the lock mortise
(Fig. 35).
12. Fix the base plate onto the lock mortise
with 2 screws M5x20 with 5 Nm.
13. Fix the door handle rose onto the base
plate with 2 screws M5x14 with 5 Nm.