Dormakaba Saflok Quantum Pixel User manual

Saflok Quantum® Pixel
Installation Instructions
PK3693-T - 2019 - 02
EN

2 Saflok Quantum Pixel PK3693_T 02-19
©2018 dormakaba USA, Inc. All trademarks and registered trademarks are the property of their respective owners.
Saflok Quantum Pixel Installation Instructions
CAUTION
WARNING
IMPORTANT
All parts needed to install the Quantum Pixel lock are included with each unit. Please check to make sure
all parts are accounted for before you begin the installation. Do not substitute any of the parts. The use
of substitute parts will result in poor performance of the lock.
All information contained herein, including but not limited to product pricing and other intellectual
property, is confidential and intended for the sole use of the addressee(s) so named. Any misuse of this
confidential information contained herein may result in legal action by dormakaba USA Inc. and
its parent company.
Door and door frame preparation
Tools required for this step
Recommend doors prepped at factory for higher precision
Do not drill both STD and ADB Ø7/16 thumb turn holes. Drill only the hole that corresponds to the mortise
purchased. Do not drill a Ø7/16 thumb turn hole for utility locks.
• Drill
• Plunge Router
- 1” Straight
- 1-⁄” Straight
• Drill bits
- ⁄” Reader
- ⁄” Thumb Turn
- ⁄” Mortise Mounting
• 2-⁄" Hole Saw
• Chisel
• Jigsaw
• 1:1 Door Prep Templates
• Optional Door Prep Jig P/N: FIXT-PIXEL (available for purchase)
- Door prep jig only available for 1-3/8" [34.9mm] OR 1-3/4" [44.5mm] doors with standard centered
lower mortise pocket and no rabbet.

Saflok Quantum Pixel PK3693_T 02-19 3
Figure 1 - Exploded Lock View
Controller face plate
#8-32 X 1/4 Flat Head Screws
#6 X 1/2 Flat Head Screws
#6 X 1/2 Flat
Head Screws Reader Cover
Reader Base
Lock Controller
#12 X 1 Pan
Head Screws
#4 X 3/16 Screw
Antenna PCB
Thumb Turn Base
Thumb Turn
Strike Plate
I/S Lever Rose
I/S Lever Assy
O/S Lever Assy
#12 X 1-1/2
OR
#12-24X 3/8
Flat Head Screws
#8-32 X 1/4 Flat Head Screws
Mortise Face Plate
Mortise
#12 X 1-1/4 Flat Head Screws
#8-32 Shoulder Screws
Figure 2 - Door preperation jig
Door and door frame preparation

4 Saflok Quantum Pixel PK3693_T 02-19
Door and door frame preparation (continued)
Figure 3 - Door preperation templates
*NOT TO SCALE
PAGE 1 - O/S TRIM &
LOWER MORTISE
PAGE 2 - I/S TRIM
PAGE 3 - UPPER
CONTROLLER MORTISE
PAGE 4 - STRIKE PREP
OUTSIDE
PREP
INSIDE
PREP
x
x
*LOWER MORTISE
CENTERED IN DOOR
*UPPER MORTISE OFFSET TO O/S DOOR
FACE IF GREATER THAN 1-3/4" DOOR
THICKNESS.
*CENTERED FOR 1-3/8" TO 1-3/4" DOOR
THICKNESS.

Saflok Quantum Pixel PK3693_T 02-19 5
Lock trim installation
Tools Required for Installation
• Driver handle (P/N: 24190)
• #1 Philips bit
• #2 Philips bit
• #3 Philips bit
• T-15 tamper resistant torx bit (P/N: A39250)
• Spanner wrench for thumb turn (P/N: A32370)
1. Lower Mortise Installation
a. Pre-Drill #12 screw pilot holes
b. Slide mortise into lower pocket
c. Route mortise cable harness along the side wire channel that connectsthe
top and bottom mortise pockets (see figure #6 for wire channel location)
d. Secure with included #12 flat head screws
e. Ensure wire harness is free and not pinched
Figure 5 - Lock Exploded View with Mounted Controller and Mortise
Figure 4 - Pixel Controller and
Mortise Mounting

6 Saflok Quantum Pixel PK3693_T 02-19
Lock trim installation (continued)
2. Controller Assembly Installation
a. Lift controller to top of pocket and center horizontally to mark pilot hole locations based on case
mounting holes
b. Pre-Drill #12 screw pilot holes, ensure holes are centered for proper face plate alignment
c. Slide tray out partially from controller to ensure tabs are not bent when securing #12 screws
d. Lift and center assembly to ensure proper alignment
e. Secure with included #12 pan head screws
f. Slide the tray out partway to and ensure all connections are secure
*Do not connect the battery at this point
g. Connect the harnesses from the mortise and controller together
*Do not seat the slide tray in door at this point
Figure 6 - Wire Channel in Door Edge
Wire Channel
Figure 7 - Controller and Mortise Harness Connection

Saflok Quantum Pixel PK3693_T 02-19 7
Lock trim installation (continued)
3. Reader Assembly Installation
Figure 8 - Exploded Reader Assembly
Reader Cover
Reader Base
Antenna PCB
#6 X 1/2 Flat
Head Screws
#4 X 3/16 Pan
Head Screw
a. Remove the antenna from the antenna base by removing the #4 mounting screw
b. Align the reader base to the 6 pin antenna socket (inside controller assembly)
with the orientation arrow facing up
c. Ensure base is level and mounting holes are horizontal
d. Mark hole centers using center punch to ensure alignment is maintained
e. Drill small pilot hole with a short depth to aid in securing the screws
*Short depth is required so that controller case is not drilled into and damaged
**Don't apply too much pressure when drilling to help maintain door integrity
f. Secure the reader base to the outside of the door using the included #6 flat head screws
*Don't apply too much torque, but ensure base is fully seated against door
g. Plug the antenna into the 6 pin socket visible through the hole in the door
Figure 9 - Reader Base
i. Align pins in upper opening
ii. Insert antenna PCB by sliding the pins carefully into the socket
*Minimal force required if properly aligned
h. Secure the antenna to the base using the #4 pan head screw removed in step a
4. Initial lock power up
a. Connect the battery to the PCB. Green LED should flash 4 times
b. Present a valid keycard to the reader. Red and green LEDs will flash and motor will activate
c. Seat the tray into the controller being careful to not pinch any wires

8 Saflok Quantum Pixel PK3693_T 02-19
Installing the lock trim (continued)
Figure 10 - Exploded Lever Set Assembly
I/S Lever Assy
O/S Lever Assy
I/S Lever Rose
#8-32 Shoulder Screws
5. Lever Set Installation (If supplied by dormakaba)
a. Place the outside lever rose assembly on the outside of the door
b. Place the inside lever rose assembly on the inside of the door
c. Secure to the outside rose assembly using the included shoulder screws
d. Carefully slide the escutcheon over the lever and ensure removal notch is aligned below
lever set for concealment

Saflok Quantum Pixel PK3693_T 02-19 9
Installing the lock trim (continued)
Figure 11 - Exploded Thumb Turn Assembly
Thumb Turn Thumb Turn Base
#6 X 1/2 Flat
Head Screws
6. Thumb Turn Installation (If supplied by dormakaba)
a. Align base centered over the mortise cam (not hole in door)
b. Mark hole centers using center punch to ensure alignment is maintained
c. Drill small pilot hole with a short depth to aid in securing the screws
d. Secure the base to the door with the included screws
e. Align turn piece onto base so that it is at 12 and 6 o'clock (see figure #12)
Figure 12 - Thumb Turn Base Alignment
Mortise Cam
f. Install the turn piece onto the base by screwing the collar on clockwise until tight; torque secure
with spanner wrench
g. Check the turn for smooth operation ensuring no drag or binding occurs
*If binding occurs; verify base alignment with mortise cam
7. Faceplate Installation
a. Install lower mortise faceplate using #8 flat head screws
b. Install upper controller assembly faceplate using #8 flat head screws
*Ensure the controller harness does not become pinched when securing faceplates

10 Saflok Quantum Pixel PK3693_T 02-19
Lock functionality testing
1. Initial Lock Test (Construction Mode)
a. Present a valid opening key to the reader
b. Ensure lock unlatches, lever turns freely, and lock re-latches
2. Lock Programming
a. Use HH6 to program lock to desired room number (see figure #13 for USB programming port)
Figure 13 - USB Programming Cable Connection
3. Reader Cover Installation
a. Locate release hole at 5:00 (see figure #14)
b. Place the lens onto the base and rotate clockwise to secure at 6:00
c. Ensure cover is secured (locking tab will click when fully seated)
*For ease of assembly and disassembly; wrap thumb around circumference of cover to get a good grip
Figure 14 - Reader Cover Installation

Saflok Quantum Pixel PK3693_T 02-19 11
Removing the cover
4. Final Lock Test
a. Present a valid opening key to reader
b. Ensure reader flashes the green LED 8 times
c. Ensure lock unlatches, lever turns freely, and lock re-latches
d. With door open; throw deadbolt and activate privacy
e. Present valid opening key to reader
f. Ensure reader flashes the yellow LED 12 times
g. Rotate inside lever to retract deadbolt and thumb turn
*Ensure I/S lever retracts smoothly
Refer to the table below for other LED feedback:
Lock Communication Electronic Function Description
Red and green LEDs flash 9 times simultaneously Time and date not set, use the Quantum LPI probe
to reset
Yellow LED flashes 12 times Dead bolt is thrown or switch cam is not properly
aligned
Yellow LED flashes 2 times Keycard not allowed OR keycard cancelled by new
keycard
Red and green LEDs flash alternately 9 times Low battery (contact the SAFLOK service
department)
Yellow and red LEDs flash 2 times simultaneously Bad keycard read or corrupted data (may require
new keycard)
5. Reader Cover Removal
a. Insert cover removal tool through release hole at bottom to unlock locking tab
b. Rotate cover counter-clockwise while maintaining upward pressure on locking tab
*A32360 Cover removal tool can be attached to HH6 programming cable or keychain
Figure 15 - Cover Removal Tool Alignment
Programming
Cable Slot
Keychain Hole
A32360 Cover Removal ToolCover Removal Tool Alignment

12 Saflok Quantum Pixel PK3693_T 02-19
Door Unit Inspection Criteria
Appearance
• Finish is free of blemishes or scratches that would distract from lock appearance
• Lock body and under plate (if used) are mounted straight on the door
• Door scalp is mounted straight and flush with the door edge
• Jamb strike is mounted straight and is flush with the jamb face
• Correction of minor blemishes on the door jamb are the responsibility of the property’s
maintenance
department
Lock Function
• Knob or lever rotates and moves freely
• Lever is horizontal to floor when at rest position
• Dead bolt extends fully and retracts without binding (door open)
• Lock latch and dead bolt engage jamb strike plate freely
• Anti-pick latch when depressed (door open)
• Anti-pick latch is depressed when contact is made with the strike plate (door closed)
Electronics/Keycards
• Present keycard in front of reader, and the yellow light flashes twice when incorrect keycard is used
• Green light flashes when the proper keycard is used
• Green light is flashing when the lever is operated
• Green light continues to flash for a five-second cycle
• Yellow light flashes 12 times when the dead bolt is extended and a guest/hotel keycard is used
• All keycards function to the specifications of the properties key design
Door function
• Door closes and latches with little or no interference
• Dead bolt extends fully through the strike plate without interference (door closed)
• Spacing between door edge and inside door jamb does not exceed ⁄” (door closed)
Note: If bumpers or other seals are added after strike plate installation and causes alignment and latch
problems, it is the property’s responsibility to correct this condition. This note generally applies to new
construction or new door installation.

Saflok Quantum Pixel PK3693_T 02-19 13
FCC and IC Warnings
FCC Interference Statement (Part 15.105 (b)):

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil
doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

PK3693-T 02-19 Subject to change without notice
www.dormakaba.com
dormakaba USA Inc.
Customer Services & Support
Saflok: 1.800.999.6213 / + 1.248.837.3700
General information:
dormakaba.us
Online consumable orders:
www.saflokstore.com
To access all of our easy steps, please
visit our support website:
www.dormakabalodgingsupport.com